The Cubox has a recessed button between the HDMI and RJ-45 connectors
that wasn't mapped in the device tree, so I've mapped it to gpio-keys
BTN_0.
Signed-off-by: George Joseph <george.joseph@fairview5.com>
Tested-by: George Joseph <george.joseph@fairview5.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Setup pwm lines as follows -
pwm1: In case HummingBoard base carrier; this pin drives through a serial
      capacitor the mono out of the audio jack.
      In case HummingBoard pro the this pad can be reached by wiring to
      C8 capacitors on the board.
pwm2: Setup pwm2 on gpio-1 but leave the default function of the iopad as
      a gpio.
      The user can change the io pad mux in user space and therefore use
      this function on gpio-1 (pin number 7 on the 26 pin header).
pwm3,pwm4: unused
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
[tweaked alias for pwm pinctrl group --rmk]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Enable the commented out PCF8523 RTC support for Hummingboard pro
base boards.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Update SolidRun iMX6 platforms DT descriptions to be dual-licensed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It may be useful to disable the internal snvs-rtc when an external rtc is
available. This patch adds a label so that dts files can disable it.

Based on a patch from Markus Pargmann for imx6qdl.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It may be useful to disable the internal snvs-rtc when an external rtc is
available. This patch adds a label so that dts files can disable it.

Based on a patch from Markus Pargmann for imx6qdl.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Now that the GPC has been converted to be a full blown irqchip
(and not a mole on the side of the GIC), booting a new kernel
with an old DT is likely to result in a rough ride for the user.

This patch makes sure such a situation is promptly detected and
the user made aware that a DT update is in order.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

While converting the GPC code to a stacked irqchip, we lost the
possibility to change the CPU affinity of an interrupt routed
through the GPC.

This patch restore the expected behaviour by forwarding the
affinity setup to the underlying irqchip (GIC).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

max7310 is an i2c interface gpio expander
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Warp has a Murata chip based on a BCM4330 that provides Wifi and Bluetooth
functionality.

Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

input values are only useful for pin functions which define a input
register. This patch removes all input values of pin functions which do
not have an input configuration register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add the Miscellaneous System Control Module (MSCM) to the base
device tree for Vybrid SoC's. This module contains registers
to get information of the individual and current (accessing)
CPU. In a second block, there is an interrupt router, which
handles the routing of the interrupts between the two CPU cores
on VF6xx variants of the SoC. However, also on single core
variants the interrupt router needs to be configured in order
to receive interrupts on the CPU's interrupt controller. Almost
all peripheral interrupts are routed through the router, hence
the MSCM module is the default interrupt parent for this SoC.

In a earlier commit the interrupt nodes were moved out of the
peripheral nodes and specified in the CPU specific vf500.dtsi
device tree. This allowed to use the base device tree vfxxx.dtsi
also for a Cortex-M4 specific device tree, which uses different
interrupt nodes due to the NVIC interrupt controller. However,
since the interrupt parent for peripherals is the MSCM module
independently which CPU the device tree is used for, we can move
the interrupt nodes into the base device tree vfxxx.dtsi again.
Depending on which CPU this base device tree will be used with,
the correct parent interrupt controller has to be assigned to
the MSCM-IR node (GIC or NVIC). The driver takes care of the
parent interrupt controller specific needs (interrupt-cells).
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

USDHC2 port uses all the 8 data signals, so pass the 'bus-width' property
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

All PWM users should explicitly enable the used PWMs in their device tree
so they can be disabled by default in imx6qdl.dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PU regulator is enabled during boot, but not necessarily always-on.
It can be disabled by the generic pm domain framework when the PU power
domain is shut down. The ramp delay of 150 us might be a bit conservative,
the value is taken from the Freescale kernel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled and a list of clocks to be enabled during powerup
for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled, and a list of phandles to all clocks that must be
enabled during powerup for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The chipidea driver adds an extra line of spam to the log when a
host-only chipidea instance is left set to the default of a dual role
controller.

[    2.010873] ci_hdrc ci_hdrc.1: doesn't support gadget

Set the dr_mode property to host on all the host-only nodes
to avoid this warning.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The WaRP Board is a Wearable Reference Plaform. The board features:

 - Freescale i.MX6 SoloLite processor with 512MB of RAM
 - Freescale FXOS8700CQ 6-axis Xtrinsic sensor
 - Freescale Kinetis KL16 MCU
 - Freescale Xtrinsic MMA955xL intelligent motion sensing platform

The board implements a hybrid architecture to address the evolving
needs of the wearables market. The platform consists of a main board
and an example daughtercard with the ability to add additional
daughtercards for different usage models.

For more information about the project, visit:

 http://www.warpboard.org/Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The anyway depricated gpio-range-cells property was never used
by the pin controller driver. This patch removes it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

IMX6 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.

This patch does just this, updating the DT files to actually
reflect what the HW provides.

BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the GPC block is actually the first
interrupt controller in the chain, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs won't even boot.
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add support for the CLAA057VC01CW display.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Add some defines currently missing, fix ordering to make the list
sorted by (mux_reg, mux_val), make sure pins are grouped by mux_reg.

The same definitions are missing from the old pinmux header
(arch/arm/mach-imx/iomux-mx25.h) but as only legacy machine support uses
that and therefor the existing list is obviously good enough I didn't
spend the effort to add the corresponding definitions there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Noticed while looking over the pad definitions. None of the bogus
definitions is used in-tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

It may be useful to disable the internal rtc snvs-rtc because an
external rtc is available. This patch adds a label so that board files
can disable this rtc.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Sebastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The MIPI DSI node contains some ports which represent possible DRM CRTCs
it can connect with.  Each port has a 'reg' property embedded.  This
property will be wrongly interpretted by the MIPI DSI bus driver, because
the driver will take each subnode which contains a 'reg' property as a
DSI peripheral device.  This patch moves the existing MIPI DSI ports into
a new 'ports' node so that the MIPI DSI bus driver may distinguish its
DSI peripheral device(s) from the existing ports.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since imx6sx-sdb reva board is experimental and will not be used
formally (eg, no software release based on it), we set revb board
as the formal imx6sx-sdb board.

The imx6sx-sdb uses pfuse200 as pmic which has only one power supply
for both VDDARM_IN and VDDSOC_IN, so VDDARM_IN and VDDSOC_IN have to
use the same (higher one in the same frequency) one as its power supply,
that's the reason we override the OPP setting in board dts file.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

The imx6sx sdb board has two revisions, the current mainline one
is reva which is experimental and mainly for internal use. In
this commit, we rename imx6sx-sdb.dts to imx6sx-sdb.dtsi, and
move the reva dedicated contents to imx6sx-sdb-reva.dts.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

MCP2515 CAN controller is available on Colibri Evaluation board.
Hence enable MCP2515 CAN.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>