Ok, this requires quite a dance to actually hit:
1) We plug in a 2nd screen, enable it in both X and (by vt-switching)
in the fbcon.
2) We disable that screen again in with xrandr.
3) We vt-switch again, so that fbcon displays on the 2nd screen, but X
on the first screen. This obviously needs a driver that doesn't switch
off unused functions when regaining the VT.
3) When X controls the vt, we unplug that screen.

Now drm_fb_helper_hotplug_event we noticed that that some crtcs are
bound, but because we still have the fbcon on the 2nd screeen we also
have bound set. Which means the fbcon wrongly assumes it's in control
of everything an happily disables the output on the 2nd screen, but
enables its fb on the first screen.

Work around this issue by counting how many crtcs are bound and how
many are bound to fbcon and assuming that when fbcon isn't bound to
all of them, it better not touch the output configuration.

Conceptually this is the same as only restoring the fbcon output
configuration on the driver's ->lastclose, when we're sure that no one
else is using kms. So this should be consistent with existing kms
drivers.

Chris has created a separate patch for the intel ddx, but I think we
should fix this issue here regardless - the fbcon messing with the
output config while it's not fully in control simply isn't a too
polite behaviour.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50772Tested-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This contains all the radeon documentation rebased on top of the ib fixes.

* 'next' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: fix SS setup for DCPLL
  drm/radeon: fix up pll selection on DCE5/6
  drm/radeon: start to document evergreen.c
  drm/radeon: start to document the functions r100.c
  drm/radeon: document VM functions in radeon_gart.c (v3)
  drm/radeon: document non-VM functions in radeon_gart.c (v2)
  drm/radeon: document radeon_ring.c (v4)
  drm/radeon: document radeon_fence.c (v2)
  drm/radeon: document radeon_asic.c
  drm/radeon: document radeon_irq_kms.c
  drm/radeon: document radeon_kms.c
  drm/radeon: document radeon_device.c (v2)
  drm/radeon: add rptr save support for r1xx-r5xx
  drm/radeon: update rptr saving logic for memory buffers
  drm/radeon: remove radeon_ring_index()
  drm/radeon: update ib_execute for SI (v2)
  drm/radeon: fix const IB handling v2
  drm/radeon: let sa manager block for fences to wait for v2
  drm/radeon: return an error if there is nothing to wait for

Need to actually set the SS parameters rather than just 0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Still a lot to do.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Still a lot more to do.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Document the VM functions in radeon_gart.c

v2: adjust per Christian's suggestions
v3: adjust to Christians's latest changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Document the non-VM functions in radeon_gart.c

v2: adjust per Christian's suggestions
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_ring.c

v2: adjust per Christian's suggestions
v3: adjust per Christian's latest patches
v4: adjust per my latest changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_fence.c

v2: address Christian's comments:
- split common concept description into it's own comment
- fix description of intr parameter
- Improve description of -EDEADLK error
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_asic.c
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_irq_kms.c
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_kms.c
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Adds documentation to most of the functions in
radeon_device.c

v2: split out general descriptions as per Christian's
comments.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Add support for using memory buffers rather than
scratch registers.  Some rings may not be able to
write to scratch registers.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Just store the index in the ring structure.
Idea taken from one of Jerome's wip rptr patches.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

When submitting a CONST_IB, emit a SWITCH_BUFFER
packet before the CONST_IB.  This isn't strictly necessary
(the driver will work fine without it), but is good practice
and allows for more flexible DE/CE sychronization options
in the future.  Current userspace drivers do not take
advantage of the CE yet.

v2: - clean up code flow a bit
    - no need to flush caches for CONST IB
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Const IBs are executed on the CE not the CP, so we can't
fence them in the normal way.

So submit them directly before the IB instead, just as
the documentation says.

v2: keep the extra documentation
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Otherwise we can encounter out of memory situations under extreme load.

v2: add documentation for the new function
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Otherwise the sa managers out of memory
handling doesn't work.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

DRM_IOCTL_MODESET_CTL must only be used for UMS drivers. Make it a no-op
for KMS drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@gmail.com>

This merges Christian work that has been hanging around on the list.

Try to save whatever is on the rings when
we encounter an lockup.

v2: Fix spelling error. Free saved ring data if reset fails.
    Add documentation for the new functions.
v3: Some more spelling fixes
v4: It doesn't make sense to save anything if all fences
    are signaled
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Before emitting any indirect buffer, emit the offset of the next
valid ring content if any. This allow code that want to resume
ring to resume ring right after ib that caused GPU lockup.

v2: use scratch registers instead of storing it into memory
v3: skip over the surface sync for ni and si as well
v4: use SET_CONFIG_REG instead of PACKET0
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Making it easier to control when it is executed.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Just restore the page table instead. Addressing three
problem with this change:

1. Calling vm_manager_suspend in the suspend path is
   problematic cause it wants to wait for the VM use
   to end, which in case of a lockup never happens.

2. In case of a locked up memory controller
   unbinding the VM seems to make it even more
   unstable, creating an unrecoverable lockup
   in the end.

3. If we want to backup/restore the leftover ring
   content we must not unbind VMs in between.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Just reinitialize the shader content on resume instead.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

The IB pool is in gart memory, so it is completely
superfluous to unpin / repin it on suspend / resume.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

It's not critical, but the current code isn't
100% correct.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

For a normal suspend/resume we allready wait for
the rings to be empty, and for a suspend/reasume
in case of a lockup we REALLY don't want to wait
for anything.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Start with last signaled fence number instead
of last emitted one.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

It is possible that radeon_fence_process is called
after writeback is disabled for suspend, leading
to an invalid read of register 0x0.

This fixes a problem for me where the fence value
is temporary incremented by 0x100000000 on
suspend/resume.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

We don't need to pad anything if the number of dwords
written to the ring already matches the requirements.

Fixes some "writting more dword to ring than expected"
warnings.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

GPU reset need to be exclusive, one happening at a time. For this
add a rw semaphore so that any path that trigger GPU activities
have to take the semaphore as a reader thus allowing concurency.

The GPU reset path take the semaphore as a writer ensuring that
no concurrent reset take place.

v2: init rw semaphore
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Don't return success if scheduling the IB fails, otherwise
we end up with an oops in ttm_eu_fence_buffer_objects.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Waiting for a fence can fail for different reasons,
the most common is a deadlock.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Instead of returning the error handle it directly
and while at it fix the comments about the ring lock.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

In order to support snoopable memory on non-LLC architectures (so that
we can bind vgem objects into the i915 GATT for example), we have to
avoid the prefetcher on the GPU from crossing memory domains and so
prevent allocation of a snoopable PTE immediately following an uncached
PTE. To do that, we need to extend the range allocator with support for
tracking and segregating different node colours.

This will be used by i915 to segregate memory domains within the GTT.

v2: Now with more drm_mm helpers and less driver interference.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>

If drm can't find proc it should fail more gracefully, than just
oopsing, this tests drm_class is NULL, and sets it to NULL in the
fail paths.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>