Cascading DSA switches can be done multiple ways. There is the brute
force approach / tag stacking, where one upstream switch, located
between leaf switches and the host Ethernet controller, will just
happily transport the DSA header of those leaf switches as payload.
For this kind of setups, DSA works without any special kind of treatment
compared to a single switch - they just aren't aware of each other.
Then there's the approach where the upstream switch understands the tags
it transports from its leaves below, as it doesn't push a tag of its own,
but it routes based on the source port & switch id information present
in that tag (as opposed to DMAC & VID) and it strips the tag when
egressing a front-facing port. Currently only Marvell implements the
latter, and Marvell DSA trees contain only Marvell switches.

So it is safe to say that DSA trees already have a single tag protocol
shared by all switches, and in fact this is what makes the switches able
to understand each other. This fact is also implied by the fact that
currently, the tagging protocol is reported as part of a sysfs installed
on the DSA master and not per port, so it must be the same for all the
ports connected to that DSA master regardless of the switch that they
belong to.

It's time to make this official and enforce it (yes, this also means we
won't have any "switch understands tag to some extent but is not able to
speak it" hardware oddities that we'll support in the future).

This is needed due to the imminent introduction of the dsa_switch_ops::
change_tag_protocol driver API. When that is introduced, we'll have
to notify switches of the tagging protocol that they're configured to
use. Currently the tag_ops structure pointer is held only for CPU ports.
But there are switches which don't have CPU ports and nonetheless still
need to be configured. These would be Marvell leaf switches whose
upstream port is just a DSA link. How do we inform these of their
tagging protocol setup/deletion?

One answer to the above would be: iterate through the DSA switch tree's
ports once, list the CPU ports, get their tag_ops, then iterate again
now that we have it, and notify everybody of that tag_ops. But what to
do if conflicts appear between one cpu_dp->tag_ops and another? There's
no escaping the fact that conflict resolution needs to be done, so we
can be upfront about it.

Ease our work and just keep the master copy of the tag_ops inside the
struct dsa_switch_tree. Reference counting is now moved to be per-tree
too, instead of per-CPU port.

There are many places in the data path that access master->dsa_ptr->tag_ops
and we would introduce unnecessary performance penalty going through yet
another indirection, so keep those right where they are.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The existence of dsa_broadcast has generated some confusion in the past:
https://www.mail-archive.com/netdev@vger.kernel.org/msg365042.html

So let's document the existing dsa_port_notify and dsa_broadcast
functions and explain when each of them should be used.

Also, in fact, the in-between function has always been there but was
lacking a name, and is the main reason for this patch: dsa_tree_notify.
Refactor dsa_broadcast to use it.

This patch also moves dsa_broadcast (a top-level function) to dsa2.c,
where it really belonged in the first place, but had no companion so it
stood with dsa_port_notify.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.

Unfortunately, a lesson learned in commit 69df578c ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.

The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.

There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Applying the bridge forwarding mask currently is done only on the STP
state changes for any port. But it depends on both STP state changes,
and bonding interface state changes. Export the bit that recalculates
the forwarding mask so that it could be reused, and call it when a port
starts and stops offloading a bonding interface.

Now that the logic is split into a separate function, we can rename "p"
into "port", since the "port" variable was already taken in
ocelot_bridge_stp_state_set. Also, we can rename "i" into "lag", to make
it more clear what is it that we're iterating through.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We will be adding some private VCAP filters that should not interfere in
any way with the filters added using tc-flower. So we need to allocate
some IDs which will not be used by tc.

Currently ocelot uses an u32 id derived from the flow cookie, which in
itself is an unsigned long. This is a problem in itself, since on 64 bit
systems, sizeof(unsigned long)=8, so the driver is already truncating
these.

Create a struct ocelot_vcap_id which contains the full unsigned long
cookie from tc, as well as a boolean that is supposed to namespace the
filters added by tc with the ones that aren't.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The Felix driver will need to preinstall some VCAP filters for its
tag_8021q implementation (outside of the tc-flower offload logic), so
these need to be exported to the common includes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The sja1105 implementation can be blind about this, but the felix driver
doesn't do exactly what it's being told, so it needs to know whether it
is a TX or an RX VLAN, so it can install the appropriate type of TCAM
rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

buf_info structures in RX & TX queues are private driver data that
do not need to be visible to the device.  Although there is physical
address and length in the queue descriptor that points to these
structures, their layout is not standardized, and device never looks
at them.

So lets allocate these structures in non-DMA-able memory, and fill
physical address as all-ones and length as zero in the queue
descriptor.

That should alleviate worries brought by Martin Radev in
https://lists.osuosl.org/pipermail/intel-wired-lan/Week-of-Mon-20210104/022829.html
that malicious vmxnet3 device could subvert SVM/TDX guarantees.
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing dependency to TAPRIO to avoid build failures such as:

|ERROR: modpost: "taprio_offload_get" [drivers/net/dsa/hirschmann/hellcreek_sw.ko] undefined!
|ERROR: modpost: "taprio_offload_free" [drivers/net/dsa/hirschmann/hellcreek_sw.ko] undefined!

Fixes: 24dfc6eb ("net: dsa: hellcreek: Add TAPRIO offloading support")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20210128163338.22665-1-kurt@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use cache friendly helpers to better use cpu caches
while reading /proc/net/netstat

Tested on a platform with 256 threads (AMD Rome)

Before: 305 usec spent in netstat_seq_show()
After: 130 usec spent in netstat_seq_show()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210128162145.1703601-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The commit 41b14fb8 ("net: Do not clear the sock TX queue in
sk_set_socket()") removes sk_tx_queue_clear() from sk_set_socket() and adds
it instead in sk_alloc() and sk_clone_lock() to fix an issue introduced in
the commit e022f0b4 ("net: Introduce sk_tx_queue_mapping"). On the
other hand, the original commit had already put sk_tx_queue_clear() in
sk_prot_alloc(): the callee of sk_alloc() and sk_clone_lock(). Thus
sk_tx_queue_clear() is called twice in each path.

If we remove sk_tx_queue_clear() in sk_alloc() and sk_clone_lock(), it
currently works well because (i) sk_tx_queue_mapping is defined between
sk_dontcopy_begin and sk_dontcopy_end, and (ii) sock_copy() called after
sk_prot_alloc() in sk_clone_lock() does not overwrite sk_tx_queue_mapping.
However, if we move sk_tx_queue_mapping out of the no copy area, it
introduces a bug unintentionally.

Therefore, this patch adds a compile-time check to take care of the order
of sock_copy() and sk_tx_queue_clear() and removes sk_tx_queue_clear() from
sk_prot_alloc() so that it does the only allocation and its callers
initialize fields.

CC: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210128150217.6060-1-kuniyu@amazon.co.jpSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Huazhong Tan says:

====================
net: hns3: updates for -next

This patchset adds dump tm info of nodes, priority and qset in debugfs.
Three debugfs files tm_nodes, tm_priority and tm_qset are created in
new tm directory, and use cat command to dump their info, for examples:

$ cat tm_nodes
       BASE_ID  MAX_NUM
PG         0         8
PRI        0         8
QSET       0         8
QUEUE      0      1024

$ cat tm_priority
ID    MODE  DWRR  C_IR_B  C_IR_U  C_IR_S  C_BS_B  C_BS_S  C_FLAG  C_RATE(Mbps)  P_IR_B  P_IR_U  P_IR_S  P_BS_B  P_BS_S  P_FLAG  P_RATE(Mbps)
0000  dwrr  100     0       0       0       5      20       0          0        150       7       0       5      20       0          0
0001    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0002    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0003    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0004    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0005    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0006    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0
0007    sp    0     0       0       0       0       0       0          0          0       0       0       0       0       0          0

$ cat tm_qset
ID    MAP_PRI  LINK_VLD  MODE  DWRR
0000     0        1      dwrr  100
0001     0        0        sp    0
0002     0        0        sp    0
0003     0        0        sp    0
0004     0        0        sp    0
0005     0        0        sp    0
0006     0        0        sp    0

change log:
V2: add readonly files for dump all nodes, priority and qset info
    suggested by Jakub Kicinski.

previous version:
V1: https://patchwork.kernel.org/project/netdevbpf/patch/1610694569-43099-1-git-send-email-tanhuazhong@huawei.com/
====================

Link: https://lore.kernel.org/r/1611834696-56207-1-git-send-email-tanhuazhong@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In order to query tm info of nodes, priority and qset
for debugging, adds three debugfs files tm_nodes,
tm_priority and tm_qset in newly created tm directory.

Unlike previous debugfs commands, these three files
just support read ops, so they only support to use cat
command to dump their info.

The new tm file style is acccording to suggestion from
Jakub Kicinski's opinion as link https://lkml.org/lkml/2020/9/29/2101.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add some interfaces to get information of tm priority and qset,
then they can be used by debugfs.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: add support for ip generic checksum offload for gre

This patchset it to add ip generic csum processing first in
skb_csum_hwoffload_help() in Patch 1/2 and then add csum
offload support for GRE header in Patch 2/2.
====================

Link: https://lore.kernel.org/r/cover.1611825446.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch is to add csum offload support for gre header:

On the TX path in gre_build_header(), when CHECKSUM_PARTIAL's set
for inner proto, it will calculate the csum for outer proto, and
inner csum will be offloaded later. Otherwise, CHECKSUM_PARTIAL
and csum_start/offset will be set for outer proto, and the outer
csum will be offloaded later.

On the GSO path in gre_gso_segment(), when CHECKSUM_PARTIAL is
not set for inner proto and the hardware supports csum offload,
CHECKSUM_PARTIAL and csum_start/offset will be set for outer
proto, and outer csum will be offloaded later. Otherwise, it
will do csum for outer proto by calling gso_make_checksum().

Note that SCTP has to do the csum by itself for non GSO path in
sctp_packet_pack(), as gre_build_header() can't handle the csum
with CHECKSUM_PARTIAL set for SCTP CRC csum offload.

v1->v2:
  - remove the SCTP part, as GRE dev doesn't support SCTP CRC CSUM
    and it will always do checksum for SCTP in sctp_packet_pack()
    when it's not a GSO packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NETIF_F_IP|IPV6_CSUM feature flag indicates UDP and TCP csum offload
while NETIF_F_HW_CSUM feature flag indicates ip generic csum offload
for HW, which includes not only for TCP/UDP csum, but also for other
protocols' csum like GRE's.

However, in skb_csum_hwoffload_help() it only checks features against
NETIF_F_CSUM_MASK(NETIF_F_HW|IP|IPV6_CSUM). So if it's a non TCP/UDP
packet and the features doesn't support NETIF_F_HW_CSUM, but supports
NETIF_F_IP|IPV6_CSUM only, it would still return 0 and leave the HW
to do csum.

This patch is to support ip generic csum processing by checking
NETIF_F_HW_CSUM for all protocols, and check (NETIF_F_IP_CSUM |
NETIF_F_IPV6_CSUM) only for TCP and UDP.

Note that we're using skb->csum_offset to check if it's a TCP/UDP
proctol, this might be fragile. However, as Alex said, for now we
only have a few L4 protocols that are requesting Tx csum offload,
we'd better fix this until a new protocol comes with a same csum
offset.

v1->v2:
  - not extend skb->csum_not_inet, but use skb->csum_offset to tell
    if it's an UDP/TCP csum packet.
v2->v3:
  - add a note in the changelog, as Willem suggested.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-next-for-5.12-20210129' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
linux-can-next-for-5.12-20210129

All patches are by me and target the mcp251xfd driver. The first 4
patches update the information regarding the "85% of (FSYSCLK/2)"
errata. The other 4 are misc cleanups, unitfy error messages, add
missing postfix to a macro, simplify the return of a function, and
make use of dev_err_probe() in the mcp251xfd_probe() function.
====================

Link: https://lore.kernel.org/r/20210129084302.3040284-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the new mhi_get_free_desc_count helper to track queue usage
instead of relying on the locally maintained rx_queued count.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The RX queue size can be determined at runtime by retrieving the
number of available transfer descriptors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Needed by mhi-net patches.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This section was missed during the conversion to ReST, so convert it in the
same style as the surrounding section titles.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Link: https://lore.kernel.org/r/20210128111930.29473-1-jlu@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simplify the code by using module_platform_driver macro
for octeon_mgmt.
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Link: https://lore.kernel.org/r/20210128035330.17676-1-dingsenjie@163.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This converts the driver to use the new tasklet API introduced in
commit 12cc923f ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-2-kernel@esmil.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Previously a temporary tasklet structure was initialized on the stack
using DECLARE_TASKLET_OLD() and then copied over and modified. Nothing
else in the kernel seems to use this pattern, so let's just call
tasklet_init() like everyone else.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Link: https://lore.kernel.org/r/20210127173256.13954-1-kernel@esmil.dkSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Paul Blakey says:

====================
net/sched: cls_flower: Add support for matching on ct_state reply flag

This patchset adds software match support and offload of flower
match ct_state reply flag (+/-rpl).

The first patch adds the definition for the flag and match to flower.

Second patch gives the direction of the connection to the offloading
drivers via ct_metadata flow offload action.

The last patch does offload of this new ct_state by using the supplied
connection's direction.
====================

Link: https://lore.kernel.org/r/1611757967-18236-1-git-send-email-paulb@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for matching on ct_state reply flag.

Example:
$ tc filter add dev ens1f0_0 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est+rpl \
  action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_1 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est-rpl \
  action mirred egress redirect dev ens1f0_0
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Give offloading drivers the direction of the offloaded ct flow,
this will be used for matches on direction (ct_state +/-rpl).
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add match on the ct_state reply flag.

Example:
$ tc filter add dev ens1f0_0 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est+rpl \
  action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_1 ingress prio 1 chain 1 proto ip flower \
  ct_state +trk+est-rpl \
  action mirred egress redirect dev ens1f0_0
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Bongsu Jeon says:

====================
Add nci suit and virtual nci device driver

1/2 is the Virtual NCI device driver.
2/2 is the NCI selftest suite
====================

Link: https://lore.kernel.org/r/20210127130829.4026-1-bongsu.jeon@samsung.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This is the NCI test suite. It tests the NFC/NCI module using virtual NCI
device. Test cases consist of making the virtual NCI device on/off and
controlling the device's polling for NCI1.0 and NCI2.0 version.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

NCI virtual device simulates a NCI device to the user. It can be used to
validate the NCI module and applications. This driver supports
communication between the virtual NCI device and NCI module.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It's better make 'pkt_sk()' inline here, as non-inline function
shouldn't occur in headers. Besides, this function is simple
enough to be inline.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20210127123302.29842-1-dong.menglong@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pointers to receive-buffer packets sent by Hyper-V are used within the
guest VM.  Hyper-V can send packets with erroneous values or modify
packet fields after they are processed by the guest.  To defend against
these scenarios, copy (sections of) the incoming packet after validating
their length and offset fields in netvsc_filter_receive().  In this way,
the packet can no longer be modified by the host.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20210126162907.21056-1-parri.andrea@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.

Link: https://lore.kernel.org/r/20210128104644.2982125-9-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch simplifies the return of the mcp251xfd_chip_clock_enable()
function by direct returning the error.

Link: https://lore.kernel.org/r/20210128104644.2982125-8-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As MCP251XFD_OBJ_FLAGS_DLC is a mask, add the missing _MASK postfix,
that all other masks in the driver have.

Link: https://lore.kernel.org/r/20210128104644.2982125-7-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch unifies the error messages:
- have a "." and the end of each message
- write controller with a small "c", if not the first word of an error
  message.

Link: https://lore.kernel.org/r/20210128104644.2982125-6-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch adds an imx6 as known good to the errata table.

Link: https://lore.kernel.org/r/20210128104644.2982125-5-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The published errata specify the maximum allowed SPI frequency to be
max 85% of (FSYSCLK/2). So there's no need to track known bad clock
settings in the driver. As the setup of known good values is a bit
tricky, keep them.

Link: https://lore.kernel.org/r/20210128104644.2982125-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>