Right now, we don't reset the id of spilled registers in case of
clear_all_pkt_pointers(). Given pkt_pointers are highly likely to
contain an id, do so by reusing __mark_reg_unknown_value().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever we set the register to the type CONST_IMM, we currently don't
reset the id to 0. id member is not used in CONST_IMM case, so don't
let it become stale, where pruning won't be able to match later on.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

spilled_regs[] state is only used for stack slots of type STACK_SPILL,
never for STACK_MISC. Right now, in states_equal(), even if we have
old and current stack state of type STACK_MISC, we compare spilled_regs[]
for that particular offset. Just skip these like we do everywhere else.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

perf_sample_data consumes 386 bytes on stack, reduce excessive stack
usage and move it to per cpu buffer. It's allowed due to preemption
being disabled for tracing, xdp and tc programs, thus at all times
only one program can run on a specific CPU and programs cannot run
from interrupt. We similarly also handle bpf_pt_regs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 2b30842b ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.

Add the missing empty stub to fix the build failure.

Fixes: Commit 2b30842b ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After moves the skb->dev and skb->protocol initialization into
ip6_output, setting the skb->dev inside ip6_fragment is unnecessary.

Fixes: 97a7a37a("ipv6: Initial skb->dev and skb->protocol in ip6_output")
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_assoc_set_id does the assoc id check in the beginning when
processing dupcookie, no need to do the same check before calling
it.

v1->v2:
  fix some typo errs Marcelo pointed in changelog.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to use read_lock_bh instead of local_bh_disable
and read_lock in sctp_eps_seq_show.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry got the following recursive locking report while running syzkaller
fuzzer, the Call Trace:
 __dump_stack lib/dump_stack.c:16 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:52
 print_deadlock_bug kernel/locking/lockdep.c:1729 [inline]
 check_deadlock kernel/locking/lockdep.c:1773 [inline]
 validate_chain kernel/locking/lockdep.c:2251 [inline]
 __lock_acquire+0xef2/0x3430 kernel/locking/lockdep.c:3340
 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755
 lock_sock_nested+0xcb/0x120 net/core/sock.c:2536
 lock_sock include/net/sock.h:1460 [inline]
 sctp_close+0xcd/0x9d0 net/sctp/socket.c:1497
 inet_release+0xed/0x1c0 net/ipv4/af_inet.c:425
 inet6_release+0x50/0x70 net/ipv6/af_inet6.c:432
 sock_release+0x8d/0x1e0 net/socket.c:597
 __sock_create+0x38b/0x870 net/socket.c:1226
 sock_create+0x7f/0xa0 net/socket.c:1237
 sctp_do_peeloff+0x1a2/0x440 net/sctp/socket.c:4879
 sctp_getsockopt_peeloff net/sctp/socket.c:4914 [inline]
 sctp_getsockopt+0x111a/0x67e0 net/sctp/socket.c:6628
 sock_common_getsockopt+0x95/0xd0 net/core/sock.c:2690
 SYSC_getsockopt net/socket.c:1817 [inline]
 SyS_getsockopt+0x240/0x380 net/socket.c:1799
 entry_SYSCALL_64_fastpath+0x1f/0xc2

This warning is caused by the lock held by sctp_getsockopt() is on one
socket, while the other lock that sctp_close() is getting later is on
the newly created (which failed) socket during peeloff operation.

This patch is to avoid this warning by use lock_sock with subclass
SINGLE_DEPTH_NESTING as Wang Cong and Marcelo's suggestion.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unneeded forward declaration of tpacket_snd()
in net/packet/af_packet.c.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two tcp_filter hooks in tcp_ipv6 ingress path currently.
One is at tcp_v6_rcv and another is in tcp_v6_do_rcv. It seems the
tcp_filter() call inside tcp_v6_do_rcv is redundent and some packet
will be filtered twice in this situation. This will cause trouble
when using eBPF filters to account traffic data.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Goal is to advertise the user when ethtool speeds and 802.3ad speeds are
desynchronized.
When this case happens, the kernel needs to be patched.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the user tries to assign a specific nsid, idr_alloc() is called with
the range [nsid, nsid+1]. If this nsid is already used, idr_alloc() returns
ENOSPC (No space left on device). In our case, it's better to return
EEXIST to make it clear that the nsid is not available.

CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It helps the user to identify errors.

CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Free up mbox_log allocated for PF0 to PF3.

Fixes: 7829451c ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_QED_SRIOV is disabled, we get a build error:

drivers/net/ethernet/qlogic/qed/qed_int.c: In function 'qed_int_sb_init':
drivers/net/ethernet/qlogic/qed/qed_int.c:1499:4: error: implicit declaration of function 'qed_vf_set_sb_info'; did you mean 'qed_mcp_get_resc_info'? [-Werror=implicit-function-declaration]

All the other declarations have a 'static inline' stub as an alternative
here, so this adds one more for qed_int_sb_init.

Fixes: 50a20714 ("qed: Hold a single array for SBs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Light L2 updates

This series does a major overhaul of the LL2 logic in qed.
The single biggest change done here is in #5 where we're changing
the API qed provides for LL2 [both internally in case of storage and
externally in case of RoCE] to become callback-based to allow cleaner
scalability in preperation to the future iWARP submission which would
aadd additional flavors of LL2. It's also the only patch in series
to modify !qed logic [qedr].

Patches prior to that mostly deal with refactoring LL2 code,
encapsulating varaious parameters into structure and re-ordering
of LL2 code. The latter patches add some small missing bits of LL2
ffunctionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The LL2 statistics already have place holders for these, but haven't
populated them so far.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver to inform the connection owner that the its buffers are being
released as part of a flush.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a legacy leftover; There's no current flow where 'frags_mapped'
would be set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LL2 today is interrupt driven - when tx/rx completion arrives [or any
other indication], qed needs to operate on the connection and pass
the information to the protocol-driver [or internal qed consumer].
Since we have several flavors of ll2 employeed by the driver,
each handler needs to do an if-else to determine the right functionality
to use based on the connection type.

In order to make things more scalable [given that we're going to add
additional types of ll2 flavors] move the infrastrucutre into using
a callback-based approach - the callbacks would be provided as part
of the connection's initialization parameters.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having the OOO logic packetd, divide it with rest of code
according to establish/release flows.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A LL2 connection [qed_ll2_info] has a sub-structure of type qed_ll2_conn
that contain various inputs for ll2 acquisition, but the connection also
utilizes a couple of other inputs.

Restructure the input structure to include all the inputs and refactor
the code necessary to populate those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This introduces qed_ll2_comp_rx_data as a public struct
and moves handling of Rx packets in LL2 into using it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First step in revising the LL2 interface, this declares
qed_ll2_tx_pkt_info as part of the ll2 interface, and uses it for
transmission instead of receiving lots of parameters.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: minor adjustment

Adjust some code to make it reasonable or satisfy the suggestion from
the engineers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stop queuing rx packets if it is more than 1000.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.

Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.

Disable U2P3 first in rtl8153_up().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llvm 5.0 does not like the section name and the function name
to be the same:

clang -I. -I./include/uapi -I../../../include/uapi \
	-I../../../../samples/bpf/ \
	-Wno-compare-distinct-pointer-types \
	-O2 -target bpf -c \
	linux/tools/testing/selftests/bpf/test_obj_id.c -o \
	linux/tools/testing/selftests/bpf/test_obj_id.o
fatal error: error in backend: 'test_prog_id' label emitted multiple times to
assembly file
clang-5.0: error: clang frontend command failed with exit code 70 (use -v to
see invocation)
clang version 5.0.0 (trunk 304326) (llvm/trunk 304329)

This patch makes changes to the section name and the function name.

Fixes: 95b9afd3 ("bpf: Test for bpf ID")
Reported-by: Alexei Starovoitov <ast@fb.com>
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

test_bpf_obj_id() should not expect a non zero jited_prog_len
to be returned by bpf_obj_get_info_by_fd() when
net.core.bpf_jit_enable is 0.

The patch checks for net.core.bpf_jit_enable and
has different expectation on jited_prog_len.

This patch also removes the pwd.h header which I forgot
to remove after making changes.

Fixes: 95b9afd3 ("bpf: Test for bpf ID")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization of skb->dev and skb->protocol from
ip6_finish_output2 to ip6_output. This can make the skb->dev and
skb->protocol information avalaible to the CGROUP eBPF filter.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>