this makes it easier to filter function traces.
No functional changes.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Whenever babble happens, MUSB controller will
drop session automatically.

The only case where it won't drop the session,
is when we're running on AM335x and SW_SESSION_CTRL
bit has been set. In that case, controller will
not touch session bit so SW has a chance to recover
from babble condition.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We want to check if that particular bit is
set. It could very well be that bootloader
(or romcode) has fiddled with MUSB before
us which could leave other bits set in this
register.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

musb->int_usb already contains the correct
information for musb-core to handle babble.

In fact, this very check was just causing a
nonsensical babble interrupt storm.

With this I can get test.sh to run and, even though
all tests fail with timeout, that's still better
than locking up the system due to IRQ storm.

Also, if I remove g_zero and load g_mass_storage,
then everything works fine again.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

MUSB does not generate a connect IRQ when working
in peripheral mode.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

when musb is operating as host and a remote wakeup
fires up, a resume interrupt will be raised. At that
point SUSPENDM bit is automatically cleared and
RESUME bit is automatically set.

Remove those two from IRQ handler.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

no functional changes, clean up only.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There was already a proper place where we were
checking for babble interrupts, move babble
recovery there.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

if reset fails, we should return a *negative*
error code, not a positive value.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

FSDEV is set for both HIGH and FULL speeds,
the correct HIGHSPEED check is done through
power register's HSMODE bit.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

no functional changes, clean up only.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

devctl & MUSB_DEVCTL_HM represents a single bit,
just check for the bit, there's really no need
to compare the result against 0.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As per the SAF1761 data sheet[0], the DcChipID register represents
the hardware version number (0001h) and the chip ID (1582h) for the
Peripheral Controller.

However as per the ISP1761 data sheet[1], the DcChipID register
represents the hardware version number (0015h) and the chip ID (8210h)
for the Peripheral Controller.

This patch adds support for both the chip ID values.

[0] http://www.nxp.com/documents/data_sheet/SAF1761.pdf
[1] http://pdf.datasheetcatalog.com/datasheets2/74/742102_1.pdf

Cc: Felipe Balbi <balbi@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The seq_printf return value, because it's frequently misused,
will eventually be converted to void.

See: commit 1f33c41c ("seq_file: Rename seq_overflow() to
     seq_has_overflowed() and make public")

While there, simplify the error handler logic by returning
immediately and remove the unnecessary labels.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Now that we're using XFERINPROGRESS for all endpoint
types (except Control), we will *always* be completing
one TRB at a time, so it's safe to remove the loop
from dwc3_cleanup_done_reqs.
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch fixes a bug where removing dwc3-omap.ko
would not trigger removal of dwc3.ko.

of_platform_depopulate() already bakes an easy to
use API for removing all our children which were
populated during probe(); Let's use that one instead
of cooking our own solution.

Note that this is kind of a revert of commit c5a1fbca
(usb: dwc3: dwc3-omap: Fix the crash on module removal)
although we can't simply revert that because a direct
call to platform_device_unregister would also be flakey.
Signed-off-by: Felipe Balbi <balbi@ti.com>

That trick is only needed if we end up with an error, so
there's no point in messing that outside of an error path.

In fact doing so causes problems when removing dwc3.ko,
problems which commit c5a1fbca (usb: dwc3: dwc3-omap: Fix
the crash on module removal) mistakenly tried to fix.
Signed-off-by: Felipe Balbi <balbi@ti.com>

instead of using manually spelled out bit-shits
and iterate over each of the 16-bits (one for
each endpoint) on each direction, we can make use
of for_each_set_bit() which internally uses
find_first_bit().

This makes the code slightly more readable while
also making we only iterate over bits which are
actually set.
Signed-off-by: Felipe Balbi <balbi@ti.com>

As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.

This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().

This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that function is pretty close to a no-op by now,
all we need is a call to musb_stop().
Signed-off-by: Felipe Balbi <balbi@ti.com>

POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"

Pull staging driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.0-rc3.

  Details are in the shortlog, nothing major, mostly IIO fixes for
  reported issues.

  All have been in linux-next successfully"

* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
  staging: comedi: vmk80xx: remove "firmware version" kernel messages
  staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
  iio: ak8975: fix AK09911 dependencies
  iio: common: ssp_sensors: Protect PM-only functions to kill warning
  IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
  Revert "iio:humidity:si7020: fix pointer to i2c client"
  iio: light: gp2ap020a00f: Select REGMAP_I2C
  iio: light: jsa1212: Select REGMAP_I2C
  iio: ad5686: fix optional reference voltage declaration
  iio:adc:mcp3422 Fix incorrect scales table
  iio: mxs-lradc: fix iio channel map regression
  iio: imu: adis16400: Fix sign extension
  staging: iio: ad2s1200: Fix sign extension
  iio: mxs-lradc: only update the buffer when its conversions have finished
  iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
  iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
  iio: mxs-lradc: separate touchscreen and buffer virtual channels
  iio: imu: inv_mpu6050: Prevent dereferencing NULL
  iio: iadc: wait_for_completion_timeout time in jiffies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are two char/misc fixes for 4.0-rc3.

  One is a reported binder driver fix needed due to a change in the mm
  core that happened in 4.0-rc1.  Another is a mei driver fix that
  resolves a reported issue in that driver.

  Both have been in linux-next for a while"

* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: make device disabled on stop unconditionally
  android: binder: fix binder mmap failures

Pull "code of conflict" from Greg KH:
 "This file tries to set the rational basis for our code reviews, gives
  some advice on how to conduct them, and provides an excalation channel
  for any kernel developers if they so desire it"

[ Let's see how this works ]

* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Code of Conflict

Pull i2c fixes from Wolfram Sang:
 "A set of updates and bugfixes for the new designware-baytrail driver.

  And a documentation bugfix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: add required clocks property to binding
  i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
  i2c: designware-baytrail: cross-check lock functions
  i2c: designware-baytrail: fix sparse warnings
  i2c: designware-baytrail: fix typo in error path
  i2c: designware-baytrail: describe magic numbers

Pull slave-dmaengine fixes from Vinod Koul:
 "This contains small fixes spread across the drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mmp_pdma: fix warning about slave caps
  dmaengine: qcom_bam_dma: fix wrong register offsets
  dmaengine: bam-dma: fix a warning about missing capabilities
  dmaengine: ioatdma: workaround for incorrect DMACAP register
  dmaengine: at_xdmac: fix for chan conf simplification
  dmaengine: dw: don't handle interrupt when dmaengine is not used
  dma: mmp-tdma: refine dma disable and dma-pos update
  dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks
  dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue

Pull arm64 fixes from Catalin Marinas:
 "arm64 and generic kernel/module.c (acked by Rusty) fixes for
  CONFIG_DEBUG_SET_MODULE_RONX"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kernel/module.c: Update debug alignment after symtable generation
  arm64: Don't use is_module_addr in setting page attributes

Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.

Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.

Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.

This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.

The first symptom  was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.

Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.

Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to handle an infinite timeout (0).

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: dcf01050 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org>	# v3.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.

Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3ffb1a81 ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.

Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix return from sprd_handle_irq() with spin_lock held.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6ae9200f ("enlarge console.name") increased the storage
for the console name to 16 bytes, but not the corresponding
struct console_cmdline::name storage. Console names longer than
8 bytes cause read beyond end-of-string and failure to match
console; I'm not sure if there are other unexpected consequences.

Cc: <stable@vger.kernel.org> # 2.6.22+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>