- 06 Aug, 2014 39 commits
-
-
Miklos Szeredi authored
commit 126b9d43 upstream. As suggested by checkpatch.pl, use time_before64() instead of direct comparison of jiffies64 values. Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> [bwh: Backported to 3.2: adjust context] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Guenter Roeck authored
commit 145e74a4 upstream. Upper limit for write operations to temperature limit registers was clamped to a fractional value. However, limit registers do not support fractional values. As a result, upper limits of 127.5 degrees C or higher resulted in a rounded limit of 128 degrees C. Since limit registers are signed, this was stored as -128 degrees C. Clamp limits to (-55, +127) degrees C to solve the problem. Value on writes to auto_temp[12]_min and auto_temp[12]_max were not clamped at all, but masked. As a result, out-of-range writes resulted in a more or less arbitrary limit. Clamp those attributes to (0, 127) degrees C for more predictable results. Cc: Axel Lin <axel.lin@ingics.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> [bwh: Backported to 3.2: - Adjust context - Driver was using SENSORS_LIMIT(), which we can replace with clamp_val()] Signed-off-by:
-
Lan Tianyu authored
commit 75646e75 upstream. Some machines (eg. Lenovo Z480) ECs are not stable during boot up and causes battery driver fails to be loaded due to failure of getting battery information from EC sometimes. After several retries, the operation will work. This patch is to retry to get battery information 5 times if the first try fails. Link: https://bugzilla.kernel.org/show_bug.cgi?id=75581Reported-and-tested-by:
naszar <naszar@ya.ru> Signed-off-by:
Lan Tianyu <tianyu.lan@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> [bwh: Backported to 3.2: acpi_battery_update() doesn't take a second parameter] Signed-off-by:
-
Lv Zheng authored
commit c0d65341 upstream. There is a race condition in ec_transaction_completed(). When ec_transaction_completed() is called in the GPE handler, it could return true because of (ec->curr == NULL). Then the wake_up() invocation could complete the next command unexpectedly since there is no lock between the 2 invocations. With the previous cleanup, the IBF=0 waiter race need not be handled any more. It's now safe to return a flag from advance_condition() to indicate the requirement of wakeup, the flag is returned from a locked context. The ec_transaction_completed() is now only invoked by the ec_poll() where the ec->curr is ensured to be different from NULL. After cleaning up, the EVT_SCI=1 check should be moved out of the wakeup condition so that an EVT_SCI raised with (ec->curr == NULL) can trigger a QR_SC command. Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911Reported-and-tested-by:
Gareth Williams <gareth@garethwilliams.me.uk> Reported-and-tested-by:
Hans de Goede <jwrdegoede@fedoraproject.org> Reported-by:
Barton Xu <tank.xuhan@gmail.com> Tested-by:
Steffen Weber <steffen.weber@gmail.com> Tested-by:
Arthur Chen <axchen@nvidia.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
-
Lv Zheng authored
commit 9b80f0f7 upstream. After we've added the first command byte write into advance_transaction(), the IBF=0 waiter is duplicated with the command completion waiter implemented in the ec_poll() because: If IBF=1 blocked the first command byte write invoked in the task context ec_poll(), it would be kicked off upon IBF=0 interrupt or timed out and retried again in the task context. Remove this seperate and duplicate IBF=0 waiter. By doing so we can reduce the overall number of times to access the EC_SC(R) status register. Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911Reported-and-tested-by:
-
Lv Zheng authored
commit f92fca00 upstream. Move the first command byte write into advance_transaction() so that all EC register accesses that can affect the command processing state machine can happen in this asynchronous state machine advancement function. The advance_transaction() function then can be a complete implementation of an asyncrhonous transaction for a single command so that: 1. The first command byte can be written in the interrupt context; 2. The command completion waiter can also be used to wait the first command byte's timeout; 3. In BURST mode, the follow-up command bytes can be written in the interrupt context directly, so that it doesn't need to return to the task context. Returning to the task context reduces the throughput of the BURST mode and in the worst cases where the system workload is very high, this leads to the hardware driven automatic BURST mode exit. In order not to increase memory consumption, convert 'done' into 'flags' to contain multiple indications: 1. ACPI_EC_COMMAND_COMPLETE: converting from original 'done' condition, indicating the completion of the command transaction. 2. ACPI_EC_COMMAND_POLL: indicating the availability of writing the first command byte. A new command can utilize this flag to compete for the right of accessing the underlying hardware. There is a follow-up bug fix that has utilized this new flag. The 2 flags are important because it also reflects a key concept of IO programs' design used in the system softwares. Normally an IO program running in the kernel should first be implemented in the asynchronous way. And the 2 flags are the most common way to implement its synchronous operations on top of the asynchronous operations: 1. POLL: This flag can be used to block until the asynchronous operations can happen. 2. COMPLETE: This flag can be used to block until the asynchronous operations have completed. By constructing code cleanly in this way, many difficult problems can be solved smoothly. Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911Reported-and-tested-by:
-
Feng Tang authored
commit a3cd8d27 upstream. Currently when advance_transaction() is called in EC interrupt handler, if there is nothing driver can do with the interrupt, it will be taken as a false one. But this is not always true, as there may be a SCI EC interrupt fired during normal read/write operation, which should not be counted as a false one. This patch fixes the problem. Signed-off-by:
Feng Tang <feng.tang@intel.com> Signed-off-by:
-
Lv Zheng authored
commit 66b42b78 upstream. The advance_transaction() will be invoked from the IRQ context GPE handler and the task context ec_poll(). The handling of this function is locked so that the EC state machine are ensured to be advanced sequentially. But there is a problem. Before invoking advance_transaction(), EC_SC(R) is read. Then for advance_transaction(), there could be race condition around the lock from both contexts. The first one reading the register could fail this race and when it passes the stale register value to the state machine advancement code, the hardware condition is totally different from when the register is read. And the hardware accesses determined from the wrong hardware status can break the EC state machine. And there could be cases that the functionalities of the platform firmware are seriously affected. For example: 1. When 2 EC_DATA(W) writes compete the IBF=0, the 2nd EC_DATA(W) write may be invalid due to IBF=1 after the 1st EC_DATA(W) write. Then the hardware will either refuse to respond a next EC_SC(W) write of the next command or discard the current WR_EC command when it receives a EC_SC(W) write of the next command. 2. When 1 EC_SC(W) write and 1 EC_DATA(W) write compete the IBF=0, the EC_DATA(W) write may be invalid due to IBF=1 after the EC_SC(W) write. The next EC_DATA(R) could never be responded by the hardware. This is the root cause of the reported issue. Fix this issue by moving the EC_SC(R) access into the lock so that we can ensure that the state machine is advanced consistently. Link: https://bugzilla.kernel.org/show_bug.cgi?id=70891 Link: https://bugzilla.kernel.org/show_bug.cgi?id=63931 Link: https://bugzilla.kernel.org/show_bug.cgi?id=59911Reported-and-tested-by:
-
Puneet Kumar authored
commit 36b15875 upstream. A bug was introduced by commit b76b51ba ('ACPI / EC: Add more debug info and trivial code cleanup') that erroneously caused the struct member to be accessed before acquiring the required lock. This change fixes it by ensuring the lock acquisition is done first. Found by Aaron Durbin <adurbin@chromium.org> Fixes: b76b51ba ('ACPI / EC: Add more debug info and trivial code cleanup') References: http://crbug.com/319019Signed-off-by:
Puneet Kumar <puneetster@chromium.org> Reviewed-by:
Aaron Durbin <adurbin@chromium.org> [olof: Commit message reworded a bit] Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Feng Tang authored
commit b76b51ba upstream. Add more debug info for EC transaction debugging, like the interrupt status register value, the detail info of a EC transaction. Signed-off-by:
-
Bernd Wachter authored
commit 3d28bd84 upstream. Add ID of the Telewell 4G v2 hardware to option driver to get legacy serial interface working Signed-off-by:
Bernd Wachter <bernd.wachter@jolla.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Andras Kovacs authored
commit b9326057 upstream. Corsair USB Dongles are shipped with Corsair AXi series PSUs. These are cp210x serial usb devices, so make driver detect these. I have a program, that can get information from these PSUs. Tested with 2 different dongles shipped with Corsair AX860i and AX1200i units. Signed-off-by:
Andras Kovacs <andras@sth.sze.hu> Signed-off-by:
-
Eric Sandeen authored
commit 5dd21424 upstream. The mount manpage says of the max_batch_time option, This optimization can be turned off entirely by setting max_batch_time to 0. But the code doesn't do that. So fix the code to do that. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.2: option parsing looks different] Signed-off-by:
-
Theodore Ts'o authored
commit ae0f78de upstream. Make it clear that values printed are times, and that it is error since last fsck. Also add note about fsck version required. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
Andreas Dilger <adilger@dilger.ca> Signed-off-by:
-
Axel Lin authored
commit 1035a9e3 upstream. Writing to fanX_div does not clear the cache. As a result, reading from fanX_div may return the old value for up to two seconds after writing a new value. This patch ensures the fan_div cache is updated in set_fan_div(). Reported-by:
Axel Lin <axel.lin@ingics.com> Signed-off-by:
-
Axel Lin authored
commit df86754b upstream. temp2_input should not be writable, fix it. Reported-by:
-
Thomas Hellstrom authored
commit 4e578080 upstream. Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register: SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to SVGA_REG_PITCHLOCK. This patch is Cc'd stable because of the unknown effects writing to this register might have, particularly on older device versions. v2: Updated log message. Cc: Christopher Friedt <chrisfriedt@gmail.com> Tested-by:
Christopher Friedt <chrisfriedt@gmail.com> Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by:
Jakob Bornecrantz <jakob@vmware.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 43d826ca upstream. We should always prefer to use full RTS protection. Using CTS to self gives a meaningless improvement, but this flow is much harder for the firmware which is likely to have issues with it. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> [bwh: Backported to 3.2: - Adjust filename - Condition for RXON_FLG_SELF_CTS_EN in iwlagn_commit_rxon() was different] Signed-off-by:
-
David Vrabel authored
commit 1b647823 upstream. Calling xen_console_resume() in xen_suspend() causes a warning because it locks irq_mapping_update_lock (a mutex) and this may sleep. If a userspace process is using the evtchn device then this mutex may be locked at the point of the stop_machine() call and xen_console_resume() would then deadlock. Resuming the console after stop_machine() returns avoids this deadlock. Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
NeilBrown authored
commit 133d4527 upstream. When we write to a degraded array which has a bitmap, we make sure the relevant bit in the bitmap remains set when the write completes (so a 're-add' can quickly rebuilt a temporarily-missing device). If, immediately after such a write starts, we incorporate a spare, commence recovery, and skip over the region where the write is happening (because the 'needs recovery' flag isn't set yet), then that write will not get to the new device. Once the recovery finishes the new device will be trusted, but will have incorrect data, leading to possible corruption. We cannot set the 'needs recovery' flag when we start the write as we do not know easily if the write will be "degraded" or not. That depends on details of the particular raid level and particular write request. This patch fixes a corruption issue of long standing and so it suitable for any -stable kernel. It applied correctly to 3.0 at least and will minor editing to earlier kernels. Reported-by:
Bill <billstuff2001@sbcglobal.net> Tested-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
HATAYAMA Daisuke authored
commit b292d7a1 upstream. Currently, any NMI is falsely handled by a NMI handler of NMI watchdog if CondChgd bit in MSR_CORE_PERF_GLOBAL_STATUS MSR is set. For example, we use external NMI to make system panic to get crash dump, but in this case, the external NMI is falsely handled do to the issue. This commit deals with the issue simply by ignoring CondChgd bit. Here is explanation in detail. On x86 NMI watchdog uses performance monitoring feature to periodically signal NMI each time performance counter gets overflowed. intel_pmu_handle_irq() is called as a NMI_LOCAL handler from a NMI handler of NMI watchdog, perf_event_nmi_handler(). It identifies an owner of a given NMI by looking at overflow status bits in MSR_CORE_PERF_GLOBAL_STATUS MSR. If some of the bits are set, then it handles the given NMI as its own NMI. The problem is that the intel_pmu_handle_irq() doesn't distinguish CondChgd bit from other bits. Unlike the other status bits, CondChgd bit doesn't represent overflow status for performance counters. Thus, CondChgd bit cannot be thought of as a mark indicating a given NMI is NMI watchdog's. As a result, if CondChgd bit is set, any NMI is falsely handled by the NMI handler of NMI watchdog. Also, if type of the falsely handled NMI is either NMI_UNKNOWN, NMI_SERR or NMI_IO_CHECK, the corresponding action is never performed until CondChgd bit is cleared. I noticed this behavior on systems with Ivy Bridge processors: Intel Xeon CPU E5-2630 v2 and Intel Xeon CPU E7-8890 v2. On both systems, CondChgd bit in MSR_CORE_PERF_GLOBAL_STATUS MSR has already been set in the beginning at boot. Then the CondChgd bit is immediately cleared by next wrmsr to MSR_CORE_PERF_GLOBAL_CTRL MSR and appears to remain 0. On the other hand, on older processors such as Nehalem, Xeon E7540, CondChgd bit is not set in the beginning at boot. I'm not sure about exact behavior of CondChgd bit, in particular when this bit is set. Although I read Intel System Programmer's Manual to figure out that, the descriptions I found are: In 18.9.1: "The MSR_PERF_GLOBAL_STATUS MSR also provides a ¡sticky bit¢ to indicate changes to the state of performancmonitoring hardware" In Table 35-2 IA-32 Architectural MSRs 63 CondChg: status bits of this register has changed. These are different from the bahviour I see on the actual system as I explained above. At least, I think ignoring CondChgd bit should be enough for NMI watchdog perspective. Signed-off-by:
HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com> Acked-by:
Don Zickus <dzickus@redhat.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/20140625.103503.409316067.d.hatayama@jp.fujitsu.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Alan Stern authored
commit b14bf2d0 upstream. Some buggy JMicron USB-ATA bridges don't know how to translate the FUA bit in READs or WRITEs. This patch adds an entry in unusual_devs.h and a blacklist flag to tell the sd driver not to use FUA. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Michael Büsch <m@bues.ch> Tested-by:
James Bottomley <James.Bottomley@HansenPartnership.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: - Adjust context - Use sd_printk() not sd_first_printk()] Signed-off-by:
-
Michal Nazarewicz authored
commit f35f7124 upstream. It appears that no one ever run ffs-test on a big-endian machine, since it used cpu-endianess for fs_count and hs_count fields which should be in little-endian format. Fix by wrapping the numbers in cpu_to_le32. Signed-off-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
J. Bruce Fields authored
commit 76f47128 upstream. An NFS operation that creates a new symlink includes the symlink data, which is xdr-encoded as a length followed by the data plus 0 to 3 bytes of zero-padding as required to reach a 4-byte boundary. The vfs, on the other hand, wants null-terminated data. The simple way to handle this would be by copying the data into a newly allocated buffer with space for the final null. The current nfsd_symlink code tries to be more clever by skipping that step in the (likely) case where the byte following the string is already 0. But that assumes that the byte following the string is ours to look at. In fact, it might be the first byte of a page that we can't read, or of some object that another task might modify. Worse, the NFSv4 code tries to fix the problem by actually writing to that byte. In the NFSv2/v3 cases this actually appears to be safe: - nfs3svc_decode_symlinkargs explicitly null-terminates the data (after first checking its length and copying it to a new page). - NFSv2 limits symlinks to 1k. The buffer holding the rpc request is always at least a page, and the link data (and previous fields) have maximum lengths that prevent the request from reaching the end of a page. In the NFSv4 case the CREATE op is potentially just one part of a long compound so can end up on the end of a page if you're unlucky. The minimal fix here is to copy and null-terminate in the NFSv4 case. The nfsd_symlink() interface here seems too fragile, though. It should really either do the copy itself every time or just require a null-terminated string. Reported-by:
Jeff Layton <jlayton@primarydata.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Amitkumar Karwar authored
commit d76744a9 upstream. https://bugzilla.kernel.org/show_bug.cgi?id=70191 https://bugzilla.kernel.org/show_bug.cgi?id=77581 It is observed that sometimes Tx packet is downloaded without adding driver's txpd header. This results in firmware parsing garbage data as packet length. Sometimes firmware is unable to read the packet if length comes out as invalid. This stops further traffic and timeout occurs. The root cause is uninitialized fields in tx_info(skb->cb) of packet used to get garbage values. In this case if MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd header was skipped. This patch makes sure that tx_info is correctly initialized to fix the problem. Reported-by:
Andrew Wiley <wiley.andrew.j@gmail.com> Reported-by:
Linus Gasser <list@markas-al-nour.org> Reported-by:
Michael Hirsch <hirsch@teufel.de> Tested-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Maithili Hinge <maithili@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Gu Zheng authored
commit 391acf97 upstream. When runing with the kernel(3.15-rc7+), the follow bug occurs: [ 9969.258987] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:586 [ 9969.359906] in_atomic(): 1, irqs_disabled(): 0, pid: 160655, name: python [ 9969.441175] INFO: lockdep is turned off. [ 9969.488184] CPU: 26 PID: 160655 Comm: python Tainted: G A 3.15.0-rc7+ #85 [ 9969.581032] Hardware name: FUJITSU-SV PRIMEQUEST 1800E/SB, BIOS PRIMEQUEST 1000 Series BIOS Version 1.39 11/16/2012 [ 9969.706052] ffffffff81a20e60 ffff8803e941fbd0 ffffffff8162f523 ffff8803e941fd18 [ 9969.795323] ffff8803e941fbe0 ffffffff8109995a ffff8803e941fc58 ffffffff81633e6c [ 9969.884710] ffffffff811ba5dc ffff880405c6b480 ffff88041fdd90a0 0000000000002000 [ 9969.974071] Call Trace: [ 9970.003403] [<ffffffff8162f523>] dump_stack+0x4d/0x66 [ 9970.065074] [<ffffffff8109995a>] __might_sleep+0xfa/0x130 [ 9970.130743] [<ffffffff81633e6c>] mutex_lock_nested+0x3c/0x4f0 [ 9970.200638] [<ffffffff811ba5dc>] ? kmem_cache_alloc+0x1bc/0x210 [ 9970.272610] [<ffffffff81105807>] cpuset_mems_allowed+0x27/0x140 [ 9970.344584] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150 [ 9970.409282] [<ffffffff811b1385>] __mpol_dup+0xe5/0x150 [ 9970.471897] [<ffffffff811b1303>] ? __mpol_dup+0x63/0x150 [ 9970.536585] [<ffffffff81068c86>] ? copy_process.part.23+0x606/0x1d40 [ 9970.613763] [<ffffffff810bf28d>] ? trace_hardirqs_on+0xd/0x10 [ 9970.683660] [<ffffffff810ddddf>] ? monotonic_to_bootbased+0x2f/0x50 [ 9970.759795] [<ffffffff81068cf0>] copy_process.part.23+0x670/0x1d40 [ 9970.834885] [<ffffffff8106a598>] do_fork+0xd8/0x380 [ 9970.894375] [<ffffffff81110e4c>] ? __audit_syscall_entry+0x9c/0xf0 [ 9970.969470] [<ffffffff8106a8c6>] SyS_clone+0x16/0x20 [ 9971.030011] [<ffffffff81642009>] stub_clone+0x69/0x90 [ 9971.091573] [<ffffffff81641c29>] ? system_call_fastpath+0x16/0x1b The cause is that cpuset_mems_allowed() try to take mutex_lock(&callback_mutex) under the rcu_read_lock(which was hold in __mpol_dup()). And in cpuset_mems_allowed(), the access to cpuset is under rcu_read_lock, so in __mpol_dup, we can reduce the rcu_read_lock protection region to protect the access to cpuset only in current_cpuset_is_being_rebound(). So that we can avoid this bug. This patch is a temporary solution that just addresses the bug mentioned above, can not fix the long-standing issue about cpuset.mems rebinding on fork(): "When the forker's task_struct is duplicated (which includes ->mems_allowed) and it races with an update to cpuset_being_rebound in update_tasks_nodemask() then the task's mems_allowed doesn't get updated. And the child task's mems_allowed can be wrong if the cpuset's nodemask changes before the child has been added to the cgroup's tasklist." Signed-off-by:
Gu Zheng <guz.fnst@cn.fujitsu.com> Acked-by:
Li Zefan <lizefan@huawei.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Brian King authored
commit 7114aae0 upstream. Add a memory barrier prior to sending a new command to the VIOS to ensure the VIOS does not receive stale data in the command buffer. Also add a memory barrier when processing the CRQ for completed commands. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Acked-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> [bwh: Backported to 3.2: as the iSeries code is still present, these functions have different names and live in rpa_vscsi.c.] Signed-off-by:
-
Brian King authored
commit 9ee75597 upstream. If a CRQ reset is triggered for some reason while in the middle of performing VSCSI adapter initialization, we don't want to call the done function for the initialization MAD commands as this will only result in two threads attempting initialization at the same time, resulting in failures. Signed-off-by:
-
Wang, Yu authored
commit d6236f6d upstream. The system suspend flow as following: 1, Freeze all user processes and kenrel threads. 2, Try to suspend all devices. 2.1, If pci device is in RPM suspended state, then pci driver will try to resume it to RPM active state in the prepare stage. 2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two workqueue items to resume usb2&usb3 roothub devices. 2.3, Call suspend callbacks of devices. 2.3.1, All suspend callbacks of all hcd's children, including roothub devices are called. 2.3.2, Finally, hcd_pci_suspend callback is called. Due to workqueue threads were already frozen in step 1, the workqueue items can't be scheduled, and the roothub devices can't be resumed in this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in usb_hcd_resume_root_hub won't be cleared. Finally, hcd_pci_suspend will return -EBUSY, and system suspend fails. The reason why this issue doesn't show up very often is due to that choose_wakeup will be called in step 2.3.1. In step 2.3.1, if udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then udev will resume to RPM active for changing the wakeup settings. This has been a lucky hit which hides this issue. For some special xHCI controllers which have no USB2 port, then roothub will not match hub driver due to probe failed. Then its do_remote_wakeup will be set to zero, and we won't be as lucky. xhci driver doesn't need to resume roothub devices everytime like in the above case. It's only needed when there are pending event TRBs. This patch should be back-ported to kernels as old as 3.2, that contains the commit f69e3120 "USB: XHCI: resume root hubs when the controller resumes" Signed-off-by:
Wang, Yu <yu.y.wang@intel.com> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Lu Baolu authored
commit ff8cbf25 upstream. When xHCI PCI host is suspended, if do_wakeup is false in xhci_pci_suspend, xhci_bus_suspend needs to clear all root port wake on bits. Otherwise some Intel platforms may get a spurious wakeup, even if PCI PME# is disabled. This patch should be back-ported to kernels as old as 2.6.37, that contains the commit 9777e3ce "USB: xHCI: bus power management implementation". Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by:
-
Mathias Nyman authored
commit 3213b151 upstream. The transfer burst count (TBC) field in xhci 1.0 hosts should be set to the number of bursts needed to transfer all packets in a isoc TD. Supported values are 0-2 (1 to 3 bursts per service interval). Formula for TBC calculation is given in xhci spec section 4.11.2.3: TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1 This patch should be applied to stable kernels since 3.0 that contain the commit 5cd43e33 "xhci 1.0: Set transfer burst count field." Suggested-by:
ShiChun Ma <masc2008@qq.com> Signed-off-by:
-
Bjørn Mork authored
commit b0ebef36 upstream. Adding a couple of Olivetti modems and blacklisting the net function on a couple which are already supported. Reported-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Johan Hovold authored
commit aea1ae87 upstream. Fix NULL-pointer dereference when probing an interface with no endpoints. These devices have two bulk endpoints per interface, but this avoids crashing the kernel if a user forces a non-FTDI device to be probed. Note that the iterator variable was made unsigned in order to avoid a maybe-uninitialized compiler warning for ep_desc after the loop. Fixes: 895f28ba ("USB: ftdi_sio: fix hi-speed device packet size calculation") Reported-by:
Mike Remski <mremski@mutualink.net> Tested-by:
-
Michal Nazarewicz authored
commit f0688c8b upstream. If the descriptors do not need any strings and user space sends empty set of strings, the ffs->stringtabs field remains NULL. Thus *ffs->stringtabs in functionfs_bind leads to a NULL pointer dereferenece. The bug was introduced by commit [fd7c9a00: “use usb_string_ids_n()”]. While at it, remove double initialisation of lang local variable in that function. ffs->strings_count does not need to be checked in any way since in the above scenario it will remain zero and usb_string_ids_n() is a no-operation when colled with 0 argument. Signed-off-by:
-
Paolo Bonzini authored
commit 7cb060a9 upstream. KVM does not really do much with the PAT, so this went unnoticed for a long time. It is exposed however if you try to do rdmsr on the PAT register. Reported-by:
Valentine Sinitsyn <valentine.sinitsyn@gmail.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Nadav Amit authored
commit 682367c4 upstream. Recent Intel CPUs have 10 variable range MTRRs. Since operating systems sometime make assumptions on CPUs while they ignore capability MSRs, it is better for KVM to be consistent with recent CPUs. Reporting more MTRRs than actually supported has no functional implications. Signed-off-by:
Nadav Amit <namit@cs.technion.ac.il> Signed-off-by:
-
David R. Piegdon authored
commit c021f241 upstream. Fix a parser-bug in the omap2 muxing code where muxtable-entries will be wrongly selected if the requested muxname is a *prefix* of their m0-entry and they have a matching mN-entry. Fix by additionally checking that the length of the m0_entry is equal. For example muxing of "dss_data2.dss_data2" on omap32xx will fail because the prefix "dss_data2" will match the mux-entries "dss_data2" as well as "dss_data20", with the suffix "dss_data2" matching m0 (for dss_data2) and m4 (for dss_data20). Thus both are recognized as signal path candidates: Relevant muxentries from mux34xx.c: _OMAP3_MUXENTRY(DSS_DATA20, 90, "dss_data20", NULL, "mcspi3_somi", "dss_data2", "gpio_90", NULL, NULL, "safe_mode"), _OMAP3_MUXENTRY(DSS_DATA2, 72, "dss_data2", NULL, NULL, NULL, "gpio_72", NULL, NULL, "safe_mode"), This will result in a failure to mux the pin at all: _omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2 Patch should apply to linus' latest master down to rather old linux-2.6 trees. Signed-off-by:
David R. Piegdon <lkml@p23q.org> [tony@atomide.com: updated description to include full description] Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Ben Hutchings authored
This reverts commit caa53449, which was commit fe6cc55f upstream. In 3.2, the transport header length is not calculated in the forwarding path, so skb_gso_network_seglen() returns an incorrect result. We also have problems due to the local_df flag not being set correctly. Signed-off-by:
-
Ben Hutchings authored
This reverts commit 59d9f389, which was commit ca6c5d4a upstream. It is a valid fix, but depends on sk_buff::local_df being set in all the right cases, which it wasn't in 3.2. We need to defer it unless and until the other fixes are also backported to 3.2.y. Signed-off-by:
-
- 11 Jul, 2014 1 commit
-
-
Ben Hutchings authored
-
