test_lru_sanity5() fails when the number of online cpus
is fewer than the number of possible cpus.  It can be
reproduced with qemu by using cmd args "--smp cpus=2,maxcpus=8".

The problem is the loop in test_lru_sanity5() is testing
'i' which is incorrect.

This patch:
1. Make sched_next_online() always return -1 if it cannot
   find a next cpu to schedule the process.
2. In test_lru_sanity5(), the parent process does
   sched_setaffinity() first (through sched_next_online())
   and the forked process will inherit it according to
   the 'man sched_setaffinity'.

Fixes: 5db58faf ("bpf: Add tests for the LRU bpf_htab")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan->cfg.dst_port is in network byte order, so an htons()
is needed here. Also reduced comment length to stay closer
to 80 column width (still slightly over, however).

Fixes: e1e5314d ("vxlan: implement GPE")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value.  This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt.  Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt.  It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch part reverts fd2a0437 and e858fae2 which introduced a
subtle change in how the virtio_net flags are derived from the SKBs
ip_summed field.

With the above commits, the flags are set to VIRTIO_NET_HDR_F_DATA_VALID
when ip_summed == CHECKSUM_UNNECESSARY, thus treating it differently to
ip_summed == CHECKSUM_NONE, which should be the same.

Further, the virtio spec 1.0 / CS04 explicitly says that
VIRTIO_NET_HDR_F_DATA_VALID must not be set by the driver.

Fixes: fd2a0437 ("virtio_net: introduce virtio_net_hdr_{from,to}_skb")
Fixes: e858fae2 (" virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Handle multicast packets properly in fast-RX path of mac80211, from
    Johannes Berg.

 2) Because of a logic bug, the user can't actually force SW
    checksumming on r8152 devices. This makes diagnosis of hw
    checksumming bugs really annoying. Fix from Hayes Wang.

 3) VXLAN route lookup does not take the source and destination ports
    into account, which means IPSEC policies cannot be matched properly.
    Fix from Martynas Pumputis.

 4) Do proper RCU locking in netvsc callbacks, from Stephen Hemminger.

 5) Fix SKB leaks in mlxsw driver, from Arkadi Sharshevsky.

 6) If lwtunnel_fill_encap() fails, we do not abort the netlink message
    construction properly in fib_dump_info(), from David Ahern.

 7) Do not use kernel stack for DMA buffers in atusb driver, from Stefan
    Schmidt.

 8) Openvswitch conntack actions need to maintain a correct checksum,
    fix from Lance Richardson.

 9) ax25_disconnect() is missing a check for ax25->sk being NULL, in
    fact it already checks this, but not in all of the necessary spots.
    Fix from Basil Gunn.

10) Action GET operations in the packet scheduler can erroneously bump
    the reference count of the entry, making it unreleasable. Fix from
    Jamal Hadi Salim. Jamal gives a great set of example command lines
    that trigger this in the commit message.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
  net sched actions: fix refcnt when GETing of action after bind
  net/mlx4_core: Eliminate warning messages for SRQ_LIMIT under SRIOV
  net/mlx4_core: Fix when to save some qp context flags for dynamic VST to VGT transitions
  net/mlx4_core: Fix racy CQ (Completion Queue) free
  net: stmmac: don't use netdev_[dbg, info, ..] before net_device is registered
  net/mlx5e: Fix a -Wmaybe-uninitialized warning
  ax25: Fix segfault after sock connection timeout
  bpf: rework prog_digest into prog_tag
  tipc: allocate user memory with GFP_KERNEL flag
  net: phy: dp83867: allow RGMII_TXID/RGMII_RXID interface types
  ip6_tunnel: Account for tunnel header in tunnel MTU
  mld: do not remove mld souce list info when set link down
  be2net: fix MAC addr setting on privileged BE3 VFs
  be2net: don't delete MAC on close on unprivileged BE3 VFs
  be2net: fix status check in be_cmd_pmac_add()
  cpmac: remove hopeless #warning
  ravb: do not use zero-length alignment DMA descriptor
  mlx4: do not call napi_schedule() without care
  openvswitch: maintain correct checksum state in conntrack actions
  tcp: fix tcp_fastopen unaligned access complaints on sparc
  ...

Merge branch 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb

Pull swiotlb fix from Konrad Rzeszutek Wilk:
 "A tiny fix to make sure that page-sized mappings are page-aligned (and
  not say straddle two pages). This is important for some drivers (such
  as NVME)"

* 'stable/for-linus-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
  swiotlb: ensure that page-sized mappings are page-aligned

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - fix regressions detecting HS/HS DDR eMMC cards related to CMD6

  MMC host:
   - mmc: mxs-mmc: Fix additional cycles after transmission stop
   - sdhci-acpi: Only powered up enabled acpi child devices
   - meson: avoid possible NULL dereference"

* tag 'mmc-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: Restore parts of the polling policy when switch to HS/HS DDR
  mmc: mxs-mmc: Fix additional cycles after transmission stop
  mmc: sdhci-acpi: Only powered up enabled acpi child devices
  MMC: meson: avoid possible NULL dereference

Pull MTD fixes from Brian Norris:
 "Just NAND updates from Boris:

   - avoid compiling xway NAND controller driver as a module (which
     didn't work)

   - fix tango NAND DT binding and make sure the controller is in a
     clean state at probe time

   - add dependency on HAS_IOMEM to the oxnas NAND driver

   - fix irq number validity check in the lpc32xx driver"

* tag 'for-linus-20170116' of git://git.infradead.org/linux-mtd:
  mtd: nand: lpc32xx: fix invalid error handling of a requested irq
  mtd: nand: tango: Reset pbus to raw mode in probe
  mtd: nand: tango: Update DT binding description
  mtd: nand: oxnas_nand: fix build errors on arch/um, require HAS_IOMEM
  mtd: nand: xway: fix build because of module functions
  mtd: nand: xway: disable module support

Demonstrating the issue:

.. add a drop action
$sudo $TC actions add action drop index 10

.. retrieve it
$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 2 bind 0 installed 29 sec used 29 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

... bug 1 above: reference is two.
    Reference is actually 1 but we forget to subtract 1.

... do a GET again and we see the same issue
    try a few times and nothing changes
~$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 2 bind 0 installed 31 sec used 31 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

... lets try to bind the action to a filter..
$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
  u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10

... and now a few GETs:
$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 3 bind 1 installed 204 sec used 204 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 4 bind 1 installed 206 sec used 206 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 5 bind 1 installed 235 sec used 235 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

.... as can be observed the reference count keeps going up.

After the fix

$ sudo $TC actions add action drop index 10
$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 1 bind 0 installed 4 sec used 4 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 1 bind 0 installed 6 sec used 6 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

$ sudo $TC qdisc add dev lo ingress
$ sudo $TC filter add dev lo parent ffff: protocol ip prio 1 \
  u32 match ip dst 127.0.0.1/32 flowid 1:1 action gact index 10

$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 2 bind 1 installed 32 sec used 32 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

$ sudo $TC -s actions get action gact index 10

	action order 1: gact action drop
	 random type none pass val 0
	 index 10 ref 2 bind 1 installed 33 sec used 33 sec
 	Action statistics:
	Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

Fixes: aecc5cef ("net sched actions: fix GETing actions")
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull NFS client bugfixes from Trond Myklebust:

 - fix invalid fget()/fput() calls when doing file locking

 - fix multiple directory cache invalidation issues due to the client
   failing to recognise that the directory wasn't changed

 - fix client recovery when server reboots multiple times

* tag 'nfs-for-4.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv4: Fix client recovery when server reboots multiple times
  NFSv4: update_changeattr should update the attribute timestamp
  NFSv4: Don't call update_changeattr() unless the unlink is successful
  NFSv4: Don't apply change_info4 twice on rename within a directory
  NFSv4: Call update_changeattr() from _nfs4_proc_open only if a file was created
  nfs: Don't take a reference on fl->fl_file for LOCK operation

Tariq Toukan says:

====================
mlx4 core fixes

This patchset contains bug fixes from Jack to the mlx4 Core driver.

Patch 1 solves a race in the flow of CQ free.
Patch 2 moves some qp context flags update to the correct qp transition.
Patch 3 eliminates warnings from the path of SRQ_LIMIT that flood the message log,
and keeps them only in the path of SRQ_CATAS_ERROR.

Series generated against net commit:
1a717fcf Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.

Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.

Fixes: acba2420 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9c ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Save the qp context flags byte containing the flag disabling vlan stripping
in the RESET to INIT qp transition, rather than in the INIT to RTR
transition. Per the firmware spec, the flags in this byte are active
in the RESET to INIT transition.

As a result of saving the flags in the incorrect qp transition, when
switching dynamically from VGT to VST and back to VGT, the vlan
remained stripped (as is required for VST) and did not return to
not-stripped (as is required for VGT).

Fixes: f0f829bf ("net/mlx4_core: Add immediate activate for VGT->VST->VGT")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function mlx4_cq_completion() and mlx4_cq_event(), the
radix_tree_lookup requires a rcu_read_lock.
This is mandatory: if another core frees the CQ, it could
run the radix_tree_node_rcu_free() call_rcu() callback while
its being used by the radix tree lookup function.

Additionally, in function mlx4_cq_event(), since we are adding
the rcu lock around the radix-tree lookup, we no longer need to take
the spinlock. Also, the synchronize_irq() call for the async event
eliminates the need for incrementing the cq reference count in
mlx4_cq_event().

Other changes:
1. In function mlx4_cq_free(), replace spin_lock_irq with spin_lock:
   we no longer take this spinlock in the interrupt context.
   The spinlock here, therefore, simply protects against different
   threads simultaneously invoking mlx4_cq_free() for different cq's.

2. In function mlx4_cq_free(), we move the radix tree delete to before
   the synchronize_irq() calls. This guarantees that we will not
   access this cq during any subsequent interrupts, and therefore can
   safely free the CQ after the synchronize_irq calls. The rcu_read_lock
   in the interrupt handlers only needs to protect against corrupting the
   radix tree; the interrupt handlers may access the cq outside the
   rcu_read_lock due to the synchronize_irq calls which protect against
   premature freeing of the cq.

3. In function mlx4_cq_event(), we change the mlx_warn message to mlx4_dbg.

4. We leave the cq reference count mechanism in place, because it is
   still needed for the cq completion tasklet mechanism.

Fixes: 6d90aa5c ("net/mlx4_core: Make sure there are no pending async events when freeing CQ")
Fixes: 225c7b1f ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't use netdev_info and friends before the net_device is registered.
This avoids ugly messages like
"meson8b-dwmac c9410000.ethernet (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As found by Olof's build bot, we gain a harmless warning about a
potential uninitialized variable reference in mlx5:

drivers/net/ethernet/mellanox/mlx5/core/en_tc.c: In function 'parse_tc_fdb_actions':
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:769:13: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:811:21: note: 'out_dev' was declared here

This was introduced through the addition of an 'IS_ERR/PTR_ERR' pair
that gcc is unfortunately unable to completely figure out.

The problem being gcc cannot tell that if(IS_ERR()) in
mlx5e_route_lookup_ipv4() is equivalent to checking if(err) later,
so it assumes that 'out_dev' is used after the 'return PTR_ERR(rt)'.

The PTR_ERR_OR_ZERO() case by comparison is fairly easy to detect
by gcc, so it can't get that wrong, so it no longer warns.

Hadar Hen Zion already attempted to fix the warning earlier by adding fake
initializations, but that ended up not fully addressing all warnings, so
I'm reverting it now that it is no longer needed.

Link: http://arm-soc.lixom.net/buildlogs/mainline/v4.10-rc3-98-gcff3b2c/
Fixes: a42485eb ("net/mlx5e: TC ipv4 tunnel encap offload error flow fixes")
Fixes: a757d108 ("net/mlx5e: Fix kbuild warnings for uninitialized parameters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ax.25 socket connection timed out & the sock struct has been
previously taken down ie. sock struct is now a NULL pointer. Checking
the sock_flag causes the segfault.  Check if the socket struct pointer
is NULL before checking sock_flag. This segfault is seen in
timed out netrom connections.

Please submit to -stable.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7bd509e3 ("bpf: add prog_digest and expose it via
fdinfo/netlink") was recently discussed, partially due to
admittedly suboptimal name of "prog_digest" in combination
with sha1 hash usage, thus inevitably and rightfully concerns
about its security in terms of collision resistance were
raised with regards to use-cases.

The intended use cases are for debugging resp. introspection
only for providing a stable "tag" over the instruction sequence
that both kernel and user space can calculate independently.
It's not usable at all for making a security relevant decision.
So collisions where two different instruction sequences generate
the same tag can happen, but ideally at a rather low rate. The
"tag" will be dumped in hex and is short enough to introspect
in tracepoints or kallsyms output along with other data such
as stack trace, etc. Thus, this patch performs a rename into
prog_tag and truncates the tag to a short output (64 bits) to
make it obvious it's not collision-free.

Should in future a hash or facility be needed with a security
relevant focus, then we can think about requirements, constraints,
etc that would fit to that situation. For now, rework the exposed
parts for the current use cases as long as nothing has been
released yet. Tested on x86_64 and s390x.

Fixes: 7bd509e3 ("bpf: add prog_digest and expose it via fdinfo/netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now, we allocate memory always with GFP_ATOMIC flag.
When the system is under memory pressure and a user tries to send,
the send fails due to low memory. However, the user application
can wait for free memory if we allocate it using GFP_KERNEL flag.

In this commit, we use allocate memory with GFP_KERNEL for all user
allocation.
Reported-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With ip6gre we have a tunnel header which also makes the tunnel MTU
smaller. We need to reserve room for it. Previously we were using up
space reserved for the Tunnel Encapsulation Limit option
header (RFC 2473).

Also, after commit b05229f4 ("gre6: Cleanup GREv6 transmit path,
call common GRE functions") our contract with the caller has
changed. Now we check if the packet length exceeds the tunnel MTU after
the tunnel header has been pushed, unlike before.

This is reflected in the check where we look at the packet length minus
the size of the tunnel header, which is already accounted for in tunnel
MTU.

Fixes: b05229f4 ("gre6: Cleanup GREv6 transmit path, call common GRE functions")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is an IPv6 version of commit 24803f38 ("igmp: do not remove igmp
souce list..."). In mld_del_delrec(), we will restore back all source filter
info instead of flush them.

Move mld_clear_delrec() from ipv6_mc_down() to ipv6_mc_destroy_dev() since
we should not remove source list info when set link down. Remove
igmp6_group_dropped() in ipv6_mc_destroy_dev() since we have called it in
ipv6_mc_down().

Also clear all source info after igmp6_group_dropped() instead of in it
because ipv6_mc_down() will call igmp6_group_dropped().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull nfsd fixes from Bruce Fields:
 "Miscellaneous nfsd bugfixes, one for a 4.10 regression, three for
  older bugs"

* tag 'nfsd-4.10-1' of git://linux-nfs.org/~bfields/linux:
  svcrdma: avoid duplicate dma unmapping during error recovery
  sunrpc: don't call sleeping functions from the notifier block callbacks
  svcrpc: don't leak contexts on PROC_DESTROY
  nfsd: fix supported attributes for acl & labels

During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.

This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.

The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.

To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.

Fixes: e3a7ae2c be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

The #warning was present 10 years ago when the driver first got merged.
As the platform is rather obsolete by now, it seems very unlikely that
the warning will cause anyone to fix the code properly.

kernelci.org reports the warning for every build in the meantime, so
I think it's better to just turn it into a code comment to reduce
noise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to alignment requirements of the hardware transmissions are split into
two DMA descriptors, a small padding descriptor of 0 - 3 bytes in length
followed by a descriptor for rest of the packet.

In the case of IP packets the first descriptor will never be zero due to
the way that the stack aligns buffers for IP packets. However, for non-IP
packets it may be zero.

In that case it has been reported that timeouts occur, presumably because
transmission stops at the first zero-length DMA descriptor and thus the
packet is not transmitted. However, in my environment a BUG is triggered as
follows:

[   20.381417] ------------[ cut here ]------------
[   20.386054] kernel BUG at lib/swiotlb.c:495!
[   20.390324] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[   20.395805] Modules linked in:
[   20.398862] CPU: 0 PID: 2089 Comm: mz Not tainted 4.10.0-rc3-00001-gf13ad2db193f #162
[   20.406689] Hardware name: Renesas Salvator-X board based on r8a7796 (DT)
[   20.413474] task: ffff80063b1f1900 task.stack: ffff80063a71c000
[   20.419404] PC is at swiotlb_tbl_map_single+0x178/0x2ec
[   20.424625] LR is at map_single+0x4c/0x98
[   20.428629] pc : [<ffff00000839c4c0>] lr : [<ffff00000839c680>] pstate: 800001c5
[   20.436019] sp : ffff80063a71f9b0
[   20.439327] x29: ffff80063a71f9b0 x28: ffff80063a20d500
[   20.444636] x27: ffff000008ed5000 x26: 0000000000000000
[   20.449944] x25: 000000067abe2adc x24: 0000000000000000
[   20.455252] x23: 0000000000200000 x22: 0000000000000001
[   20.460559] x21: 0000000000175ffe x20: ffff80063b2a0010
[   20.465866] x19: 0000000000000000 x18: 0000ffffcae6fb20
[   20.471173] x17: 0000ffffa09ba018 x16: ffff0000087c8b70
[   20.476480] x15: 0000ffffa084f588 x14: 0000ffffa09cfa14
[   20.481787] x13: 0000ffffcae87ff0 x12: 000000000063abe2
[   20.487098] x11: ffff000008096360 x10: ffff80063abe2adc
[   20.492407] x9 : 0000000000000000 x8 : 0000000000000000
[   20.497718] x7 : 0000000000000000 x6 : ffff000008ed50d0
[   20.503028] x5 : 0000000000000000 x4 : 0000000000000001
[   20.508338] x3 : 0000000000000000 x2 : 000000067abe2adc
[   20.513648] x1 : 00000000bafff000 x0 : 0000000000000000
[   20.518958]
[   20.520446] Process mz (pid: 2089, stack limit = 0xffff80063a71c000)
[   20.526798] Stack: (0xffff80063a71f9b0 to 0xffff80063a720000)
[   20.532543] f9a0:                                   ffff80063a71fa30 ffff00000839c680
[   20.540374] f9c0: ffff80063b2a0010 ffff80063b2a0010 0000000000000001 0000000000000000
[   20.548204] f9e0: 000000000000006e ffff80063b23c000 ffff80063b23c000 0000000000000000
[   20.556034] fa00: ffff80063b23c000 ffff80063a20d500 000000013b1f1900 0000000000000000
[   20.563864] fa20: ffff80063ffd18e0 ffff80063b2a0010 ffff80063a71fa60 ffff00000839cd10
[   20.571694] fa40: ffff80063b2a0010 0000000000000000 ffff80063ffd18e0 000000067abe2adc
[   20.579524] fa60: ffff80063a71fa90 ffff000008096380 ffff80063b2a0010 0000000000000000
[   20.587353] fa80: 0000000000000000 0000000000000001 ffff80063a71fac0 ffff00000864f770
[   20.595184] faa0: ffff80063b23caf0 0000000000000000 0000000000000000 0000000000000140
[   20.603014] fac0: ffff80063a71fb60 ffff0000087e6498 ffff80063a20d500 ffff80063b23c000
[   20.610843] fae0: 0000000000000000 ffff000008daeaf0 0000000000000000 ffff000008daeb00
[   20.618673] fb00: ffff80063a71fc0c ffff000008da7000 ffff80063b23c090 ffff80063a44f000
[   20.626503] fb20: 0000000000000000 ffff000008daeb00 ffff80063a71fc0c ffff000008da7000
[   20.634333] fb40: ffff80063b23c090 0000000000000000 ffff800600000037 ffff0000087e63d8
[   20.642163] fb60: ffff80063a71fbc0 ffff000008807510 ffff80063a692400 ffff80063a20d500
[   20.649993] fb80: ffff80063a44f000 ffff80063b23c000 ffff80063a69249c 0000000000000000
[   20.657823] fba0: 0000000000000000 ffff80063a087800 ffff80063b23c000 ffff80063a20d500
[   20.665653] fbc0: ffff80063a71fc10 ffff0000087e67dc ffff80063a20d500 ffff80063a692400
[   20.673483] fbe0: ffff80063b23c000 0000000000000000 ffff80063a44f000 ffff80063a69249c
[   20.681312] fc00: ffff80063a5f1a10 000000103a087800 ffff80063a71fc70 ffff0000087e6b24
[   20.689142] fc20: ffff80063a5f1a80 ffff80063a71fde8 000000000000000f 00000000000005ea
[   20.696972] fc40: ffff80063a5f1a10 0000000000000000 000000000000000f ffff00000887fbd0
[   20.704802] fc60: fffffff43a5f1a80 0000000000000000 ffff80063a71fc80 ffff000008880240
[   20.712632] fc80: ffff80063a71fd90 ffff0000087c7a34 ffff80063afc7180 0000000000000000
[   20.720462] fca0: 0000ffffcae6fe18 0000000000000014 0000000060000000 0000000000000015
[   20.728292] fcc0: 0000000000000123 00000000000000ce ffff0000088d2000 ffff80063b1f1900
[   20.736122] fce0: 0000000000008933 ffff000008e7cb80 ffff80063a71fd80 ffff0000087c50a4
[   20.743951] fd00: 0000000000008933 ffff000008e7cb80 ffff000008e7cb80 000000100000000e
[   20.751781] fd20: ffff80063a71fe4c 0000ffff00000300 0000000000000123 0000000000000000
[   20.759611] fd40: 0000000000000000 ffff80063b1f0000 000000000000000e 0000000000000300
[   20.767441] fd60: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[   20.775271] fd80: 0000000000000000 0000000000000000 ffff80063a71fda0 ffff0000087c8c20
[   20.783100] fda0: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[   20.790930] fdc0: ffffffffffffffff 0000ffffa0903078 0000000000000000 000000001ea87232
[   20.798760] fde0: 000000000000000f ffff80063a71fe40 ffff800600000014 ffff000000000001
[   20.806590] fe00: 0000000000000000 0000000000000000 ffff80063a71fde8 0000000000000000
[   20.814420] fe20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
[   20.822249] fe40: 0000000203000011 0000000000000000 0000000000000000 ffff80063a68aa00
[   20.830079] fe60: ffff80063a68aa00 0000000000000003 0000000000008933 ffff0000081f1b9c
[   20.837909] fe80: 0000000000000000 ffff000008082f30 0000000000000000 0000800637260000
[   20.845739] fea0: ffffffffffffffff 0000ffffa07ca81c 0000000060000000 0000000000000015
[   20.853569] fec0: 0000000000000003 000000001ea87232 000000000000000f 0000000000000000
[   20.861399] fee0: 0000ffffcae6fe18 0000000000000014 0000000000000300 0000000000000000
[   20.869228] ff00: 00000000000000ce 0000000000000000 00000000ffffffff 0000000000000000
[   20.877059] ff20: 0000000000000002 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[   20.884888] ff40: 0000000000000000 0000ffffa09ba018 0000ffffcae6fb20 000000001ea87010
[   20.892718] ff60: 0000ffffa09b9000 0000ffffcae6fe30 0000ffffcae6fe18 000000000000000f
[   20.900548] ff80: 0000000000000003 000000001ea87232 0000000000000000 0000000000000000
[   20.908378] ffa0: 0000000000000000 0000ffffcae6fdc0 0000ffffa09a7824 0000ffffcae6fdc0
[   20.916208] ffc0: 0000ffffa0903078 0000000060000000 0000000000000003 00000000000000ce
[   20.924038] ffe0: 0000000000000000 0000000000000000 ffffffffffffffff ffffffffffffffff
[   20.931867] Call trace:
[   20.934312] Exception stack(0xffff80063a71f7e0 to 0xffff80063a71f910)
[   20.940750] f7e0: 0000000000000000 0001000000000000 ffff80063a71f9b0 ffff00000839c4c0
[   20.948580] f800: ffff80063a71f840 ffff00000888a6e4 ffff80063a24c418 ffff80063a24c448
[   20.956410] f820: 0000000000000000 ffff00000811cd54 ffff80063a71f860 ffff80063a24c458
[   20.964240] f840: ffff80063a71f870 ffff00000888b258 ffff80063a24c418 0000000000000001
[   20.972070] f860: ffff80063a71f910 ffff80063a7b7028 ffff80063a71f890 ffff0000088825e4
[   20.979899] f880: 0000000000000000 00000000bafff000 000000067abe2adc 0000000000000000
[   20.987729] f8a0: 0000000000000001 0000000000000000 ffff000008ed50d0 0000000000000000
[   20.995560] f8c0: 0000000000000000 0000000000000000 ffff80063abe2adc ffff000008096360
[   21.003390] f8e0: 000000000063abe2 0000ffffcae87ff0 0000ffffa09cfa14 0000ffffa084f588
[   21.011219] f900: ffff0000087c8b70 0000ffffa09ba018
[   21.016097] [<ffff00000839c4c0>] swiotlb_tbl_map_single+0x178/0x2ec
[   21.022362] [<ffff00000839c680>] map_single+0x4c/0x98
[   21.027411] [<ffff00000839cd10>] swiotlb_map_page+0xa4/0x138
[   21.033072] [<ffff000008096380>] __swiotlb_map_page+0x20/0x7c
[   21.038821] [<ffff00000864f770>] ravb_start_xmit+0x174/0x668
[   21.044484] [<ffff0000087e6498>] dev_hard_start_xmit+0x8c/0x120
[   21.050407] [<ffff000008807510>] sch_direct_xmit+0x108/0x1a0
[   21.056064] [<ffff0000087e67dc>] __dev_queue_xmit+0x194/0x4cc
[   21.061807] [<ffff0000087e6b24>] dev_queue_xmit+0x10/0x18
[   21.067214] [<ffff000008880240>] packet_sendmsg+0xf40/0x1220
[   21.072873] [<ffff0000087c7a34>] sock_sendmsg+0x18/0x2c
[   21.078097] [<ffff0000087c8c20>] SyS_sendto+0xb0/0xf0
[   21.083150] [<ffff000008082f30>] el0_svc_naked+0x24/0x28
[   21.088462] Code: d34bfef7 2a1803f3 1a9f86d6 35fff878 (d4210000)
[   21.094611] ---[ end trace 5bc544ad491f3814 ]---
[   21.099234] Kernel panic - not syncing: Fatal exception in interrupt
[   21.105587] Kernel Offset: disabled
[   21.109073] Memory Limit: none
[   21.112126] ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Fixes: 2f45d190 ("ravb: minimize TX data copying")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable BH around the call to napi_schedule() to avoid following warning

[   52.095499] NOHZ: local_softirq_pending 08
[   52.421291] NOHZ: local_softirq_pending 08
[   52.608313] NOHZ: local_softirq_pending 08

Fixes: 8d59de8f ("net/mlx4_en: Process all completions in RX rings after port goes up")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2017-01-16

Here are a couple of important 802.15.4 driver fixes for the 4.10
kernel.

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.

The commit e173f891 ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.

To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.

In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Gary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f891 ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>

Merge tag 'mac80211-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
We have a number of fixes, in part because I was late
in actually sending them out - will try to do better in
the future:
 * handle VHT opmode properly when hostapd is controlling
   full station state
 * two fixes for minimum channel width in mac80211
 * don't leave SMPS set to junk in HT capabilities
 * fix headroom when forwarding mesh packets, recently
   broken by another fix that failed to take into account
   frame encryption
 * fix the TID in null-data packets indicating EOSP (end
   of service period) in U-APSD
 * prevent attempting to use (and then failing which
   results in crashes) TXQs on stations that aren't added
   to the driver yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When executing conntrack actions on skbuffs with checksum mode
CHECKSUM_COMPLETE, the checksum must be updated to account for
header pushes and pulls. Otherwise we get "hw csum failure"
logs similar to this (ICMP packet received on geneve tunnel
via ixgbe NIC):

[  405.740065] genev_sys_6081: hw csum failure
[  405.740106] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G          I     4.10.0-rc3+ #1
[  405.740108] Call Trace:
[  405.740110]  <IRQ>
[  405.740113]  dump_stack+0x63/0x87
[  405.740116]  netdev_rx_csum_fault+0x3a/0x40
[  405.740118]  __skb_checksum_complete+0xcf/0xe0
[  405.740120]  nf_ip_checksum+0xc8/0xf0
[  405.740124]  icmp_error+0x1de/0x351 [nf_conntrack_ipv4]
[  405.740132]  nf_conntrack_in+0xe1/0x550 [nf_conntrack]
[  405.740137]  ? find_bucket.isra.2+0x62/0x70 [openvswitch]
[  405.740143]  __ovs_ct_lookup+0x95/0x980 [openvswitch]
[  405.740145]  ? netif_rx_internal+0x44/0x110
[  405.740149]  ovs_ct_execute+0x147/0x4b0 [openvswitch]
[  405.740153]  do_execute_actions+0x22e/0xa70 [openvswitch]
[  405.740157]  ovs_execute_actions+0x40/0x120 [openvswitch]
[  405.740161]  ovs_dp_process_packet+0x84/0x120 [openvswitch]
[  405.740166]  ovs_vport_receive+0x73/0xd0 [openvswitch]
[  405.740168]  ? udp_rcv+0x1a/0x20
[  405.740170]  ? ip_local_deliver_finish+0x93/0x1e0
[  405.740172]  ? ip_local_deliver+0x6f/0xe0
[  405.740174]  ? ip_rcv_finish+0x3a0/0x3a0
[  405.740176]  ? ip_rcv_finish+0xdb/0x3a0
[  405.740177]  ? ip_rcv+0x2a7/0x400
[  405.740180]  ? __netif_receive_skb_core+0x970/0xa00
[  405.740185]  netdev_frame_hook+0xd3/0x160 [openvswitch]
[  405.740187]  __netif_receive_skb_core+0x1dc/0xa00
[  405.740194]  ? ixgbe_clean_rx_irq+0x46d/0xa20 [ixgbe]
[  405.740197]  __netif_receive_skb+0x18/0x60
[  405.740199]  netif_receive_skb_internal+0x40/0xb0
[  405.740201]  napi_gro_receive+0xcd/0x120
[  405.740204]  gro_cell_poll+0x57/0x80 [geneve]
[  405.740206]  net_rx_action+0x260/0x3c0
[  405.740209]  __do_softirq+0xc9/0x28c
[  405.740211]  irq_exit+0xd9/0xf0
[  405.740213]  do_IRQ+0x51/0xd0
[  405.740215]  common_interrupt+0x93/0x93

Fixes: 7f8a436e ("openvswitch: Add conntrack action")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull namespace fixes from Eric Biederman:
 "This tree contains 4 fixes.

  The first is a fix for a race that can causes oopses under the right
  circumstances, and that someone just recently encountered.

  Past that are several small trivial correct fixes. A real issue that
  was blocking development of an out of tree driver, but does not appear
  to have caused any actual problems for in-tree code. A potential
  deadlock that was reported by lockdep. And a deadlock people have
  experienced and took the time to track down caused by a cleanup that
  removed the code to drop a reference count"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  sysctl: Drop reference added by grab_header in proc_sys_readdir
  pid: fix lockdep deadlock warning due to ucount_lock
  libfs: Modify mount_pseudo_xattr to be clear it is not a userspace mount
  mnt: Protect the mountpoint hashtable with mount_lock

Pull char/misc driver fixes from Greg KH:
 "Here are some small char/misc driver fixes for 4.10-rc4 that resolve
  some reported issues.

  The MEI driver issue resolves a lot of problems that people have been
  having, as does the mem driver fix. The other minor fixes resolve
  other reported issues.

  All of these have been in linux-next for a while"

* tag 'char-misc-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  vme: Fix wrong pointer utilization in ca91cx42_slave_get
  auxdisplay: fix new ht16k33 build errors
  ppdev: don't print a free'd string
  extcon: return error code on failure
  drivers: char: mem: Fix thinkos in kmem address checks
  mei: bus: enable OS version only for SPT and newer

Merge tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fix from Greg KH:
 "Here is a single patch being reverted to remove a feature that was
  added in 4.10-rc1 that isn't quite ready for release.

  It will be redone as a debugfs file instead of a sysfs file in the
  future"

* tag 'driver-core-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Revert "driver core: Add deferred_probe attribute to devices in sysfs"

Pull tty/serial fixes from Greg KH:
 "Here are some small tty/serial driver fixes for 4.10-rc4 to resolve a
  number of reported issues.

  Nothing major here at all, one revert of a problematic patch, and some
  other tiny bugfixes. Full details are in the shortlog below.

  All have been in linux-next with no reported issues"

* tag 'tty-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  sysrq: attach sysrq handler correctly for 32-bit kernel
  Revert "tty: serial: 8250: add CON_CONSDEV to flags"
  Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break
  8250_pci: Fix potential use-after-free in error path
  tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done
  tty/serial: atmel_serial: BUG: stop DMA from transmitting in stop_tx

Pull USB fixes from Greg KH:
 "Here are a few small USB driver fixes for 4.10-rc4 to resolve some
  reported issues.

  The "largest" here is a number of bugs being fixed in the ch341
  usb-serial driver, to hopefully resolve the mess of different devices
  floating around that use this driver that have been having problems
  with the 4.10-rc1 release.

  There's also a tiny musb fix that I missed in the last pull request,
  as well as the traditional xhci fix rounding out the batch.

  All have been in linux-next with no reported issues"

* tag 'usb-4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  xhci: fix deadlock at host remove by running watchdog correctly
  USB: serial: ch341: fix control-message error handling
  usb: musb: fix runtime PM in debugfs
  wusbcore: Fix one more crypto-on-the-stack bug
  USB: serial: kl5kusb105: fix line-state error handling
  USB: serial: ch341: fix baud rate and line-control handling
  USB: serial: ch341: fix line settings after reset-resume
  USB: serial: ch341: fix resume after reset
  USB: serial: ch341: fix open error handling
  USB: serial: ch341: fix modem-control and B0 handling
  USB: serial: ch341: fix open and resume after B0
  USB: serial: ch341: fix initial modem-control state

Pull i2c fixes from Wolfram Sang:
 "Bugfixes for I2C. Mostly core this time which is a bit unusual but
  nothing really scary in there"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: piix4: Avoid race conditions with IMC
  i2c: fix spelling mistake: "insufficent" -> "insufficient"
  i2c: print correct device invalid address
  i2c: do not enable fall back to Host Notify by default
  i2c: fix kernel memory disclosure in dev interface