This patch adds a new network driver implementing MHI transport for
network packets. Packets can be in any format, though QMAP (rmnet)
is the usual protocol (flow control + PDN mux).

It support two MHI devices, IP_HW0 which is, the path to the IPA
(IP accelerator) on qcom modem, And IP_SW0 which is the software
driven IP path (to modem CPU).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-2-git-send-email-loic.poulain@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This function can be used by client driver to determine whether it's
possible to queue new elements in a channel ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604424234-24446-1-git-send-email-loic.poulain@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ioana Ciornei says:

====================
net: phy: add support for shared interrupts (part 1)

This patch set aims to actually add support for shared interrupts in
phylib and not only for multi-PHY devices. While we are at it,
streamline the interrupt handling in phylib.

For a bit of context, at the moment, there are multiple phy_driver ops
that deal with this subject:

- .config_intr() - Enable/disable the interrupt line.

- .ack_interrupt() - Should quiesce any interrupts that may have been
  fired.  It's also used by phylib in conjunction with .config_intr() to
  clear any pending interrupts after the line was disabled, and before
  it is going to be enabled.

- .did_interrupt() - Intended for multi-PHY devices with a shared IRQ
  line and used by phylib to discern which PHY from the package was the
  one that actually fired the interrupt.

- .handle_interrupt() - Completely overrides the default interrupt
  handling logic from phylib. The PHY driver is responsible for checking
  if any interrupt was fired by the respective PHY and choose
  accordingly if it's the one that should trigger the link state machine.

From my point of view, the interrupt handling in phylib has become
somewhat confusing with all these callbacks that actually read the same
PHY register - the interrupt status.  A more streamlined approach would
be to just move the responsibility to write an interrupt handler to the
driver (as any other device driver does) and make .handle_interrupt()
the only way to deal with interrupts.

Another advantage with this approach would be that phylib would gain
support for shared IRQs between different PHY (not just multi-PHY
devices), something which at the moment would require extending every
PHY driver anyway in order to implement their .did_interrupt() callback
and duplicate the same logic as in .ack_interrupt(). The disadvantage
of making .did_interrupt() mandatory would be that we are slightly
changing the semantics of the phylib API and that would increase
confusion instead of reducing it.

What I am proposing is the following:

- As a first step, make the .ack_interrupt() callback optional so that
  we do not break any PHY driver amid the transition.

- Every PHY driver gains a .handle_interrupt() implementation that, for
  the most part, would look like below:

	irq_status = phy_read(phydev, INTR_STATUS);
	if (irq_status < 0) {
		phy_error(phydev);
		return IRQ_NONE;
	}

	if (!(irq_status & irq_mask))
		return IRQ_NONE;

	phy_trigger_machine(phydev);

	return IRQ_HANDLED;

- Remove each PHY driver's implementation of the .ack_interrupt() by
  actually taking care of quiescing any pending interrupts before
  enabling/after disabling the interrupt line.

- Finally, after all drivers have been ported, remove the
  .ack_interrupt() and .did_interrupt() callbacks from phy_driver.

This patch set is part 1 and it addresses the changes needed in phylib
and 7 PHY drivers. The rest can be found on my Github branch here:
https://github.com/IoanaCiornei/linux/commits/phylib-shared-irq

I do not have access to most of these PHY's, therefore I Cc-ed the
latest contributors to the individual PHY drivers in order to have
access, hopefully, to more regression testing.

Changes in v2:
 - Rework the .handle_interrupt() implementation for each driver so that
   only the enabled interrupts are taken into account when
   IRQ_NONE/IRQ_HANDLED it returned. The main idea is so that we avoid
   falsely blaming a device for triggering an interrupt when this is not
   the case.
   The only devices for which I was unable to make this adjustment were
   the BCM8706, BCM8727, BCMAC131 and BCM5241 since I do not have access
   to their datasheets.
 - I also updated the pseudo-code added in the cover-letter so that it's
   more clear how a .handle_interrupt() callback should look like.
====================
Tested-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201101125114.1316879-1-ciorneiioana@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Michael Walle <michael@walle.cc>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.

After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.

Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.

For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.

At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.

To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.

Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.

Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.

Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

inet(6)_skb_parm was removed from sctp_input_cb by Commit a1dd2cf2
("sctp: allow changing transport encap_port by peer packets"), as it
thought sctp_input_cb->header is not used any more in SCTP.

syzbot reported a crash:

  [ ] BUG: KASAN: use-after-free in decode_session6+0xe7c/0x1580
  [ ]
  [ ] Call Trace:
  [ ]  <IRQ>
  [ ]  dump_stack+0x107/0x163
  [ ]  kasan_report.cold+0x1f/0x37
  [ ]  decode_session6+0xe7c/0x1580
  [ ]  __xfrm_policy_check+0x2fa/0x2850
  [ ]  sctp_rcv+0x12b0/0x2e30
  [ ]  sctp6_rcv+0x22/0x40
  [ ]  ip6_protocol_deliver_rcu+0x2e8/0x1680
  [ ]  ip6_input_finish+0x7f/0x160
  [ ]  ip6_input+0x9c/0xd0
  [ ]  ipv6_rcv+0x28e/0x3c0

It was caused by sctp_input_cb->header/IP6CB(skb) still used in sctp rx
path decode_session6() but some members overwritten by sctp6_rcv().

This patch is to fix it by bring inet(6)_skb_parm back to sctp_input_cb
and not overwriting it in sctp4/6_rcv() and sctp_udp_rcv().

Reported-by: syzbot+5be8aebb1b7dfa90ef31@syzkaller.appspotmail.com
Fixes: a1dd2cf2 ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/136c1a7a419341487c504be6d1996928d9d16e02.1604472932.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kurt Kanzenbach says:

====================
Hirschmann Hellcreek DSA driver

this series adds a DSA driver for the Hirschmann Hellcreek TSN switch
IP. Characteristics of that IP:

 * Full duplex Ethernet interface at 100/1000 Mbps on three ports
 * IEEE 802.1Q-compliant Ethernet Switch
 * IEEE 802.1Qbv Time-Aware scheduling support
 * IEEE 1588 and IEEE 802.1AS support

That IP is used e.g. in

 https://www.arrow.com/en/campaigns/arrow-kairos

Due to the hardware setup the switch driver is implemented using DSA. A special
tagging protocol is leveraged. Furthermore, this driver supports PTP and
hardware timestamping.

This work is part of the AccessTSN project: https://www.accesstsn.com/

The previous versions can be found here:

 * https://lkml.kernel.org/netdev/20200618064029.32168-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200710113611.3398-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200723081714.16005-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200820081118.10105-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200901125014.17801-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20200904062739.3540-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20201004112911.25085-1-kurt@linutronix.de/
 * https://lkml.kernel.org/netdev/20201028074221.29326-1-kurt@linutronix.de/

Changes since v7:

 * Simplify tagging code (rebase to net-next)
 * Pass info instead of ptr (Florian Fainelli)
 * Fix yamllint warnings (Rob Herring)

Changes since v6:

 * Add .tail_tag = true (Vladimir Oltean)
 * Fix vlan_filtering=0 bridges (Vladimir Oltean)
 * Enforce restrictions (Vladimir Oltean)
 * Sort stuff alphabetically (Vladimir Oltean)
 * Rename hellcreek.yaml to hirschmann,hellcreek.yaml
 * Typo fixes

Changes since v5:

 * Implement configure_vlan_while_not_filtering behavior (Vladimir Oltean)
 * Minor cleanups

Changes since v4:

 * Fix W=1 compiler warnings (kernel test robot)
 * Add tags

Changes since v3:

 * Drop TAPRIO support (David Miller)
   => Switch to mutexes due to the lack of hrtimers
 * Use more specific compatible strings and add platform data (Andrew Lunn)
 * Fix Kconfig ordering (Andrew Lunn)

Changes since v2:

 * Make it compile by getting all requirements merged first (Jakub Kicinski, David Miller)
 * Use "tsn" for TSN register set (Rob Herring)
 * Fix DT binding issues (Rob Herring)

Changes since v1:

 * Code simplifications (Florian Fainelli, Vladimir Oltean)
 * Fix issues with hellcreek.yaml bindings (Florian Fainelli)
 * Clear reserved field in ptp v2 event messages (Richard Cochran)
 * Make use of generic ptp parsing function (Richard Cochran, Vladimir Oltean)
 * Fix Kconfig (Florian Fainelli)
 * Add tags (Florian Fainelli, Rob Herring, Richard Cochran)

Changes since RFC ordered by reviewers:

 * Andrew Lunn
   * Use dev_dbg for debug messages
   * Get rid of __ function names where possible
   * Use reverse xmas tree variable ordering
   * Remove redundant/useless checks
   * Improve comments e.g. for PTP
   * Fix Kconfig ordering
   * Make LED handling more generic and provide info via DT
   * Setup advertisement of PHYs according to hardware
   * Drop debugfs patch
 * Jakub Kicinski
   * Fix compiler warnings
 * Florian Fainelli
   * Switch to YAML DT bindings
 * Richard Cochran
   * Fix typo
   * Add missing NULL checks
====================

Link: https://lore.kernel.org/r/20201103071101.3222-1-kurt@linutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add basic documentation and example.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Hirschmann is building devices for automation and networking. Add them to the
vendor prefixes.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The switch has two controllable I/Os which are usually connected to LEDs. This
is useful to immediately visually see the PTP status.

These provide two signals:

 * is_gm

   This LED can be activated if the current device is the grand master in that
   PTP domain.

 * sync_good

   This LED can be activated if the current device is in sync with the network
   time.

Expose these via the LED framework to be controlled via user space
e.g. linuxptp.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The switch has the ability to take hardware generated time stamps per port for
PTPv2 event messages in Rx and Tx direction. That is useful for achieving needed
time synchronization precision for TSN devices/switches. So add support for it.

There are two directions:

 * RX

   The switch has a single register per port to capture a timestamp. That
   mechanism is not used due to correlation problems. If the software processing
   is too slow and a PTPv2 event message is received before the previous one has
   been processed, false timestamps will be captured. Therefore, the switch can
   do "inline" timestamping which means it can insert the nanoseconds part of
   the timestamp directly into the PTPv2 event message. The reserved field (4
   bytes) is leveraged for that. This might not be in accordance with (older)
   PTP standards, but is the only way to get reliable results.

 * TX

   In Tx direction there is no correlation problem, because the software and the
   driver has to ensure that only one event message is "on the fly". However,
   the switch provides also a mechanism to check whether a timestamp is
   lost. That can only happen when a timestamp is read and at this point another
   message is timestamped. So, that lost bit is checked just in case to indicate
   to the user that the driver or the software is somewhat buggy.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The switch has internal PTP hardware clocks. Add support for it. There are three
clocks:

 * Synchronized
 * Syntonized
 * Free running

Currently the synchronized clock is exported to user space which is a good
default for the beginning. The free running clock might be exported later
e.g. for implementing 802.1AS-2011/2020 Time Aware Bridges (TAB). The switch
also supports cross time stamping for that purpose.

The implementation adds support setting/getting the time as well as offset and
frequency adjustments. However, the clock only holds a partial timeofday
timestamp. This is why we track the seconds completely in software (see overflow
work and last_ts).

Furthermore, add the PTP multicast addresses into the FDB to forward that
packages only to the CPU port where they are processed by a PTP program.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are
implementing features needed for Time Sensitive Networking (TSN) such as support
for the Time Precision Protocol and various shapers like the Time Aware Shaper.

This driver includes basic support for networking:

 * VLAN handling
 * FDB handling
 * Port statistics
 * STP
 * Phylink
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some switches rely on unique pvids to ensure port separation in
standalone mode, because they don't have a port forwarding matrix
configurable in hardware. So, setups like a group of 2 uppers with the
same VLAN, swp0.100 and swp1.100, will cause traffic tagged with VLAN
100 to be autonomously forwarded between these switch ports, in spite
of there being no bridge between swp0 and swp1.

These drivers need to prevent this from happening. They need to have
VLAN filtering enabled in standalone mode (so they'll drop frames tagged
with unknown VLANs) and they can only accept an 8021q upper on a port as
long as it isn't installed on any other port too. So give them the
chance to veto bad user requests.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Kurt: Pass info instead of ptr]
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The Hirschmann Hellcreek TSN switches have a special tagging protocol for frames
exchanged between the CPU port and the master interface. The format is a one
byte trailer indicating the destination or origin port.

It's quite similar to the Micrel KSZ tagging. That's why the implementation is
based on that code.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Allow user to request action terse dump with new flag value
TCA_FLAG_TERSE_DUMP. Only output essential action info in terse dump (kind,
stats, index and cookie, if set by the user when creating the action). This
is different from filter terse dump where index is excluded (filter can be
identified by its own handle).

Move tcf_action_dump_terse() function to the beginning of source file in
order to call it from tcf_dump_walker().
Signed-off-by: Vlad Buslov <vlad@buslov.dev>
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20201102201243.287486-1-vlad@buslov.devSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

1) Move existing bridge packet reject infra to nf_reject_{ipv4,ipv6}.c
   from Jose M. Guisado.

2) Consolidate nft_reject_inet initialization and dump, also from Jose.

3) Add the netdev reject action, from Jose.

4) Allow to combine the exist flag and the destroy command in ipset,
   from Joszef Kadlecsik.

5) Expose bucket size parameter for hashtables, also from Jozsef.

6) Expose the init value for reproducible ipset listings, from Jozsef.

7) Use __printf attribute in nft_request_module, from Andrew Lunn.

8) Allow to use reject from the inet ingress chain.

* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
  netfilter: nft_reject_inet: allow to use reject from inet ingress
  netfilter: nftables: Add __printf() attribute
  netfilter: ipset: Expose the initval hash parameter to userspace
  netfilter: ipset: Add bucketsize parameter to all hash types
  netfilter: ipset: Support the -exist flag with the destroy command
  netfilter: nft_reject: add reject verdict support for netdev
  netfilter: nft_reject: unify reject init and dump into nft_reject
  netfilter: nf_reject: add reject skbuff creation helpers
====================

Link: https://lore.kernel.org/r/20201104141149.30082-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mat Martineau says:

====================
mptcp: Miscellaneous MPTCP fixes

This is a collection of small fixup and minor enhancement patches that
have accumulated in the MPTCP tree while net-next was closed. These are
prerequisites for larger changes we have queued up.

Patch 1 refines receive buffer autotuning.

Patches 2 and 4 are some minor locking and refactoring changes.

Patch 3 improves GRO and RX coalescing with MPTCP skbs.

Patches 5-7 add a sysctl for tuning ADD_ADDR retransmission timeout,
corresponding test code, and documentation.

v2: Add sysctl documentation and fix signoff tags.
====================

Link: https://lore.kernel.org/r/20201103190509.27416-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This patch added the test case for retransmitting ADD_ADDR when timeout
occurs. It set NS1's add_addr_timeout to 1 second, and drop NS2's ADD_ADDR
echo packets.

Here we need to slow down the transfer process of all data to let the
ADD_ADDR suboptions can be retransmitted three times. So we added a new
parameter "speed" for do_transfer, it can be set with fast or slow.

We also added three new optional parameters for run_tests, and dropped
run_remove_tests function.

Since we added the netfilter rules in this test case, we need to update
the "config" file.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Describe the two MPTCP sysctls, what the values mean, and the default
settings.
Acked-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch added a new sysctl, named add_addr_timeout, to control the
timeout value (in seconds) of the ADD_ADDR retransmission.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mptcp_clean_una() will wake writers in case memory could be reclaimed.
When called from mptcp_sendmsg the wakeup code isn't needed.

Move the wakeup to a new helper and then use that from the mptcp worker.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the TCP stack splits a packet on the write queue, the tail
half currently lose the associated skb extensions, and will not
carry the DSM on the wire.

The above does not cause functional problems and is allowed by
the RFC, but interact badly with GRO and RX coalescing, as possible
candidates for aggregation will carry different TCP options.

This change tries to improve the MPTCP behavior, propagating the
skb extensions on split.

Additionally, we must prevent the MPTCP stack from updating the
mapping after the split occur: that will both violate the RFC and
fool the reader.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>