When compiling with clang in certain configurations, an objtool warning
appears:

drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: warning: objtool:
ipq806x_gmac_probe() falls through to next function phy_modes()

This happens because the unreachable annotation in the third switch
statement is not eliminated. The compiler should know that the first
default case would prevent the second and third from being reached as
the comment notes but sanitizer options can make it harder for the
compiler to reason this out.

Help the compiler out by eliminating the unreachable() annotation and
unifying the default case error handling so that there is no objtool
warning, the meaning of the code stays the same, and there is less
duplication.
Reported-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
s390/qeth: Add bridge to switchdev LEARNING_SYNC

The netlink bridgeport attribute LEARNING_SYNC can be used to enable
qeth interfaces to report MAC addresses that are reachable via this
qeth interface to the attached software bridge via switchdev
notifiers SWITCHDEV_FDB_ADD_TO_BRIDGE and SWITCHDEV_FDB_DEL_TO_BRIDGE.

Extend this support of LEARNING_SYNC to the bridge to switchdev notifiers
SWITCHDEV_FDB_ADD_TO_DEVICE and SWITCHDEV_FDB_DEL_TO_DEVICE.

Add the capability to sync MAC addresses that are learned by a
north-facing, non-isolated bridgeport of a software bridge to
south-facing, isolated bridgeports. This enables the software bridge to
influence south to north traffic steering in hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the MAC addresses that are registered with a LEARNING_SYNC qeth
device with the events announced by the attached software bridge.

Typically the LEARNING_SYNC qeth bridge port has an isolated sibling (the
default interface of an 'HiperSockets Converged Interface' (HSCI)). Update
the MACs of isolated siblings as well, to avoid unnecessary flooding in
the attached virtualized switches.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

QETH HiperSockets devices with LEARNING_SYNC capability can be used
to construct a linux bridge with:
2 isolated southbound interfaces:
     a) a default network interface
     b) a LEARNING-SYNC HiperSockets interface
and 1 non-isolated northbound interface. This is called a 'HiperSockets
Converged Interface' (HSCI).
The existing LEARNING_SYNC functionality is used to update the bridge fdb
with MAC addresses that should be sent-out via the HiperSockets interface,
instead of the default network interface.

Add handling of switchdev events SWITCHDEV_FDB_ADD_TO_DEVICE and
SWITCHDEV_FDB_DEL_TO_DEVICE to the qeth LEARNING_SYNC functionality. Thus
if the northbound bridgeport of an HSCI doesn't only have a single static
MAC address, but instead is a learning bridgeport, work is enqueued, so
the HiperSockets virtual switch (that is external to this Linux instance)
can update its fdb.

When BRIDGE is a loadable module, QETH_L2 mustn't be built-in:

drivers/s390/net/qeth_l2_main.o: in function 'qeth_l2_switchdev_event':
drivers/s390/net/qeth_l2_main.c:927: undefined reference to
'br_port_flag_is_set'

Add Kconfig dependency to enforce usable configurations.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conditionally register a qeth_l2 switchdev_event handler to handle bridge
to device switchdev events, when at least one qeth interface has the
bridgeport attribute LEARNING_SYNC enabled.
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The true check on the variable startable in the ternary operator
is always false because the previous if statement handles the true
condition for startable. Hence the ternary check is dead code and
can be removed.

Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 9ffc513f ("net: ethernet: ti: davinci_cpdma: drop
frame padding") which has depndency from not yet merged patch [1] and so
breaks cpsw_new driver.

[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210805145511.12016-1-grygorii.strashko@ti.com/
Fixes: 9ffc513f ("net: ethernet: ti: davinci_cpdma: drop frame padding")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20210806142809.15069-1-grygorii.strashko@ti.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The "skb" pointer is NULL on this error path so we can't dereference it.
Use "dev" instead.

Fixes: 14ee70ca ("vrf: use skb_expand_head in vrf_finish_output")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210806150435.GB15586@kiliSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver currently still accepts untagged frames on VLAN-aware ports
without PVID. Use PVC.ACC_FRM to drop untagged frames in that case.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Always flood multicast to the DSA CPU port

Discussing with Qingfang, it became obvious that DSA is not prepared to
disable multicast flooding towards the CPU port under any circumstance
right now, and this in fact breaks traffic quite blatantly.

This series is a revert done in reverse chronological order. These
should be propagated to stable trees up to commit a8b659e7 ("net:
dsa: act as passthrough for bridge port flags") which is in v5.12.
For older kernels, that commit blocks further backporting, so I need to
send a modified version of patch 3 separately to Greg after these go
into "net".

v1->v2: delete unused b53_set_mrouter function prototype
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).

And commit a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.

The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:

- ICMP6 neighbor solicitation messages are unregistered multicast
  packets as far as the bridge is concerned. So if we stop flooding
  multicast, the outside world cannot ping the bridge device's IPv6
  link-local address.

- There might be foreign interfaces bridged with our DSA switch ports
  (sending a packet towards the host does not necessarily equal
  termination, but maybe software forwarding). So if there is no one
  interested in that multicast traffic in the local network stack, that
  doesn't mean nobody is.

- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
  the bridge is concerned. This should reach the CPU port.

- The switch driver might not do FDB partitioning. And since we don't
  even bother to do more fine-grained flood disabling (such as "disable
  flooding _from_port_N_ towards the CPU port" as opposed to "disable
  flooding _from_any_port_ towards the CPU port"), this breaks standalone
  ports, or even multiple bridges where one has an IGMP querier and one
  doesn't.

Reverting the logic makes all of the above work.

Fixes: a8b659e7 ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA's idea of optimizing out multicast flooding to the CPU port leaves
quite a few holes open, so it should be reverted.

The mt7530 driver is the only new driver which added a .port_set_mrouter
implementation after the reorg from commit a8b659e7 ("net: dsa: act
as passthrough for bridge port flags"), so it needs to be reverted
separately so that the other revert commit can go a bit further down the
git history.

Fixes: 5a30833b ("net: dsa: mt7530: support MDB and bridge flag operations")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qingfang points out that when a bridge with the default settings is
created and a port joins it:

ip link add br0 type bridge
ip link set swp0 master br0

DSA calls br_multicast_router() on the bridge to see if the br0 device
is a multicast router port, and if it is, it enables multicast flooding
to the CPU port, otherwise it disables it.

If we look through the multicast_router_show() sysfs or at the
IFLA_BR_MCAST_ROUTER netlink attribute, we see that the default mrouter
attribute for the bridge device is "1" (MDB_RTR_TYPE_TEMP_QUERY).

However, br_multicast_router() will return "0" (MDB_RTR_TYPE_DISABLED),
because an mrouter port in the MDB_RTR_TYPE_TEMP_QUERY state may not be
actually _active_ until it receives an actual IGMP query. So, the
br_multicast_router() function should really have been called
br_multicast_router_active() perhaps.

When/if an IGMP query is received, the bridge device will transition via
br_multicast_mark_router() into the active state until the
ip4_mc_router_timer expires after an multicast_querier_interval.

Of course, this does not happen if the bridge is created with an
mcast_router attribute of "2" (MDB_RTR_TYPE_PERM).

The point is that in lack of any IGMP query messages, and in the default
bridge configuration, unregistered multicast packets will not be able to
reach the CPU port through flooding, and this breaks many use cases
(most obviously, IPv6 ND, with its ICMP6 neighbor solicitation multicast
messages).

Leave the multicast flooding setting towards the CPU port down to a driver
level decision.

Fixes: 010e269f ("net: dsa: sync up switchdev objects and port attributes when joining the bridge")
Reported-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables support for hard irqs deferral feature from Eric Dumazet
[1] for TI K3 CPSW driver by using napi_complete_done() in TX completion
path.

Depending on gro_flush_timeout and napi_defer_hard_irqs at gives up to 30%
CPU utilization reduction:

gro_flush_timeout=50000
napi_defer_hard_irqs=2

netperf -l 10 -H 192.168.1.1  -t UDP_STREAM -c -C -- -m 1470
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.1 () port 0 AF_INET
Socket  Message  Elapsed      Messages                   CPU      Service
Size    Size     Time         Okay Errors   Throughput   Util     Demand
bytes   bytes    secs            #      #   10^6bits/sec % SS     us/KB

before:
212992    1470   10.00      809632      0      952.0     42.98    14.792
212992           10.00      809630             952.0     50.66    8.719

after:
212992    1470   10.00      813686      0      956.8     32.14    11.009
212992           10.00      813686             956.8     50.05    8.570

[1] https://lore.kernel.org/netdev/20200422161329.56026-1-edumazet@google.com/Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On TI K3 am64x platform the issue with RX IRQ is observed - it's become
disabled forever after .ndo_stop(). The K3 CPSW driver manipulates RX IRQ
by using standard Linux enable_irq()/disable_irq_nosync() API as there is
no IRQ enable/disable options in CPSW HW itself, as result during
.ndo_stop() following sequence happens

  phy_stop()
  teardown TX/RX channels
  wait for TX tdown complete
  napi_disable(TX)
  clean up TX channels

  (a)

  napi_disable(RX)

At point (a) it's not possible to predict if RX IRQ was triggered or not.
if RX IRQ was triggered then it also not possible to definitely say if RX
NAPI was run or only scheduled and immediately canceled by
napi_disable(RX). Actually the last case causes RX IRQ to be permanently
disabled.

Another observed issue is that RX IRQ enable counter become unbalanced if
(gro_flush_timeout =! 0) while (napi_defer_hard_irqs == 0):

Unbalanced enable for IRQ 44
WARNING: CPU: 0 PID: 10 at ../kernel/irq/manage.c:776 __enable_irq+0x38/0x80
__enable_irq+0x38/0x80
enable_irq+0x54/0xb0
am65_cpsw_nuss_rx_poll+0x2f4/0x368
__napi_poll+0x34/0x1b8
net_rx_action+0xe4/0x220
_stext+0x11c/0x284
run_ksoftirqd+0x4c/0x60

To avoid above issues introduce flag indicating if RX was actually disabled
before enabling it in am65_cpsw_nuss_rx_poll() and restore RX IRQ state in
.ndo_open()

Fixes: 4f7cce27 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jonathan Lemon says:

====================
ptp: ocp: assorted fixes.

Assorted fixes for the ocp timecard.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After writing an image blob to the flash memory, a reboot is required
to reload the FPGA.  There is no versioning prsent in the FPGA image
file, so only a running version is available.  The 'stored version'
was set to 'pending' in order to indicate a reboot was needed.

This isn't reliable, as the module could be unloaded/loaded, losing
the "reboot needed" indicator.  Also, the devlink 'stored version'
information is designed to refer to the actual image version.

Unfortunately, there is no method to determine the flash image version
other than booting it, so remove the devlink stored version setting.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TimeCard has two FPGA images in the flash: the actual firmware,
and a manufacturing fallback version which is intended to act as a
loader in case the flash update failed.

Name these "fw" and "loader", which are reflected in devlink:

    [root@timecard drv]# devlink dev info
    pci/0000:04:00.0:
      driver ptp_ocp
      serial_number fc:c2:3d:2e:d7:c0
      versions:
          running:
            fw 5
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GPS is not the only available positioning system.  Use the generic
naming of "GNSS" instead.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"devlink health" was used as a way to monitor the GNSS signal
status.  This isn't really the intended use, and the same
functionality can be achived by monitoring the status file.

Remove the devlink heath support entirely, and also remove the
currently unused devlink parameters.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two PPS blocks: one handles the external PPS signal output,
with the other handling the PPS signal input to the internal clock.
Add controls for the external PPS block.

Rename the fields so they match their function.

Add cable_delay to the register definitions.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the put_device() call to the error handling path, so the
device is released after the .release callback, avoiding a
use-after-free.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian reported that after d43c65b0 Coverity complains about a
missing check whether dev is NULL in ethnl_ops_complete().
There doesn't seem to be any valid case where dev could be NULL when
calling ethnl_ops_begin(), therefore return an error if dev is NULL.

Fixes: d43c65b0 ("ethtool: runtime-resume netdev parent in ethnl_ops_begin")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't progress with adding and deleting ports as long as devlink
reload is running.

Fixes: 23809a72 ("netdevsim: Forbid devlink reload when adding or deleting ports")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Grygorii Strashko says:

====================
net: ethernet: ti: cpsw/emac: switch to use skb_put_padto()

Now frame padding in TI TI CPSW/EMAC is implemented in a bit of entangled way as
frame SKB padded in drivers (without skb->len) while frame length fixed in CPDMA.
Things became even more confusing hence CPSW switcdev driver need to perform min
TX frame length correction in switch mode [1].

To avoid further confusion, make xmit path more clear and linear, and avoid
updating CPDMA configuration interface for min TX frame length correction
(which is not CPDMA job in general) this series switches TI CPSW/EMAC
drivers to skb_put_padto() instead of skb_padto() in their xmit path, so
skb->len also got updated properly and then removes TX frame length
fixup from CPDMA code.

[1] https://patchwork.kernel.org/project/netdevbpf/patch/20210611132732.10690-1-grygorii.strashko@ti.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hence all users of davinci_cpdma switched to skb_put_padto() the frame
padding can be removed from it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).

Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
  589918df ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
  0fac6aa0 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")

Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from ipsec.

  Current release - regressions:

   - sched: taprio: fix init procedure to avoid inf loop when dumping

   - sctp: move the active_key update after sh_keys is added

  Current release - new code bugs:

   - sparx5: fix build with old GCC & bitmask on 32-bit targets

  Previous releases - regressions:

   - xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix

   - xfrm: fixes for the compat netlink attribute translator

   - phy: micrel: Fix detection of ksz87xx switch

  Previous releases - always broken:

   - gro: set inner transport header offset in tcp/udp GRO hook to avoid
     crashes when such packets reach GSO

   - vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec

   - dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110

   - bridge: validate the NUD_PERMANENT bit when adding an extern_learn
     FDB entry

   - usb: lan78xx: don't modify phy_device state concurrently

   - usb: pegasus: check for errors of IO routines"

* tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
  net: vxge: fix use-after-free in vxge_device_unregister
  net: fec: fix use-after-free in fec_drv_remove
  net: pegasus: fix uninit-value in get_interrupt_interval
  net: ethernet: ti: am65-cpsw: fix crash in am65_cpsw_port_offload_fwd_mark_update()
  bnx2x: fix an error code in bnx2x_nic_load()
  net: wwan: iosm: fix recursive lock acquire in unregister
  net: wwan: iosm: correct data protocol mask bit
  net: wwan: iosm: endianness type correction
  net: wwan: iosm: fix lkp buildbot warning
  net: usb: lan78xx: don't modify phy_device state concurrently
  docs: networking: netdevsim rules
  net: usb: pegasus: Remove the changelog and DRIVER_VERSION.
  net: usb: pegasus: Check the return value of get_geristers() and friends;
  net/prestera: Fix devlink groups leakage in error flow
  net: sched: fix lockdep_set_class() typo error for sch->seqlock
  net: dsa: qca: ar9331: reorder MDIO write sequence
  VSOCK: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST
  mptcp: drop unused rcu member in mptcp_pm_addr_entry
  net: ipv6: fix returned variable type in ip6_skb_dst_mtu
  nfp: update ethtool reporting of pauseframe control
  ...

syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].

It seems that history of this locking problem is a trial and error.

Commit b40df574 ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.

Then, commit 4ce61d1c ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.

Then, commit 4b5dd696 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().

Then, commit e305509e ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.

This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).

But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.

Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.

Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag.  There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.

Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull selinux fix from Paul Moore:
 "One small SELinux fix for a problem where an error code was not being
  propagated back up to userspace when a bogus SELinux policy is loaded
  into the kernel"

* tag 'selinux-pr-20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: correct the return value when loads initial sids

Pull ucounts fix from Eric Biederman:
 "Fix a subtle locking versus reference counting bug in the ucount
  changes, found by syzbot"

* 'for-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  ucounts: Fix race condition between alloc_ucounts and put_ucounts

Pull tracing fixes from Steven Rostedt:
 "Various tracing fixes:

   - Fix NULL pointer dereference caused by an error path

   - Give histogram calculation fields a size, otherwise it breaks
     synthetic creation based on them.

   - Reject strings being used for number calculations.

   - Fix recordmcount.pl warning on llvm building RISC-V allmodconfig

   - Fix the draw_functrace.py script to handle the new trace output

   - Fix warning of smp_processor_id() in preemptible code"

* tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Quiet smp_processor_id() use in preemptable warning in hwlat
  scripts/tracing: fix the bug that can't parse raw_trace_func
  scripts/recordmcount.pl: Remove check_objcopy() and $can_use_local
  tracing: Reject string operand in the histogram expression
  tracing / histogram: Give calculation hist_fields a size
  tracing: Fix NULL pointer dereference in start_creating

Pull s390 fixes from Heiko Carstens:

 - fix zstd build for -march=z900 (undefined reference to __clzdi2)

 - add missing .got.plts to vdso linker scripts to fix kpatch build
   errors

 - update defconfigs

* tag 's390-5.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: update defconfigs
  s390/boot: fix zstd build for -march=z900
  s390/vdso: add .got.plt in vdso linker script

Pull kvm fixes from Paolo Bonzini:
 "Mostly bugfixes; plus, support for XMM arguments to Hyper-V hypercalls
  now obeys KVM_CAP_HYPERV_ENFORCE_CPUID.

  Both the XMM arguments feature and KVM_CAP_HYPERV_ENFORCE_CPUID are
  new in 5.14, and each did not know of the other"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86/mmu: Fix per-cpu counter corruption on 32-bit builds
  KVM: selftests: fix hyperv_clock test
  KVM: SVM: improve the code readability for ASID management
  KVM: SVM: Fix off-by-one indexing when nullifying last used SEV VMCB
  KVM: Do not leak memory for duplicate debugfs directories
  KVM: selftests: Test access to XMM fast hypercalls
  KVM: x86: hyper-v: Check if guest is allowed to use XMM registers for hypercall input
  KVM: x86: Introduce trace_kvm_hv_hypercall_done()
  KVM: x86: hyper-v: Check access to hypercall before reading XMM registers
  KVM: x86: accept userspace interrupt only if no event is injected

Pull pcmcia fix from Dominik Brodowski:
 "Zheyu Ma found and fixed a null pointer dereference bug in the device
  driver for the i82092 card reader"

* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
  pcmcia: i82092: fix a null pointer dereference bug

This program always prints 4096 and hangs before the patch, and always
prints 8192 and exits successfully after:

  int main()
  {
      int pipefd[2];
      for (int i = 0; i < 1025; i++)
          if (pipe(pipefd) == -1)
              return 1;
      size_t bufsz = fcntl(pipefd[1], F_GETPIPE_SZ);
      printf("%zd\n", bufsz);
      char *buf = calloc(bufsz, 1);
      write(pipefd[1], buf, bufsz);
      read(pipefd[0], buf, bufsz-1);
      write(pipefd[1], buf, 1);
  }

Note that you may need to increase your RLIMIT_NOFILE before running the
program.

Fixes: 759c0114 ("pipe: limit the per-user amount of pages allocated in pipes")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/lkml/1628086770.5rn8p04n6j.none@localhost/
Link: https://lore.kernel.org/lkml/1628127094.lxxn016tj7.none@localhost/Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pavel Skripkin says:

====================
net: fix use-after-free bugs

I've added new checker to smatch yesterday. It warns about using
netdev_priv() pointer after free_{netdev,candev}() call. I hope, it will
get into next smatch release.

Some of the reported bugs are fixed and upstreamed already, but Dan ran new
smatch with allmodconfig and found 2 more. Big thanks to Dan for doing it,
because I totally forgot to do it.
====================

Link: https://lore.kernel.org/r/cover.1628091954.git.paskripkin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);

Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function

Fixes: 6cca2003 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>