[why]
We have dynamic power control in driver but
should be ignored when power is forced on.

[how]
Bypass any power control when it's forced on.

Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.

Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

KFD_GC_VERSION was recently updated to use a new function
for IP version checks. As a result, use KFD_GC_VERSION as
the common function for all IP version checks in KFD.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.

The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.

[How]
Build the table based on DcfClock with the following assumptions:

1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.

2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.

3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.

[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix the amdgpu runpm dereference usage count.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.

[How]
As a workaround, increase the limit to block these panels.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.

[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.

Don't support enabling Z8 during the DRR region.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Fix a memory overflow issue in the gfx IB test
for some ASICs. At least 20 bytes are needed for
the IB test packet.

v2: correct code indentation errors. (Christian)
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

enable init_registers callback func for nbio v7.11.
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.

[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[WHY]
Currently DCN35 does not spread DPREFCLK

[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.

[How]
Use the correct cm3_helper function.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.

[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Setting register to force ordering to prevent read/write or write/read
hazards for un-cached modes.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x

In nbio v7_9, host driver should not issu gpu reset
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We can override SR watermarks but not Z8 ones.

[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.

These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The smu needs to get the rlc power down message to sync the rlc state
with smu, the rlc state updating message need to be sent at while smu
begin suspend sequence , otherwise SMU will crash while RLC state is not
notified by driver, and rlc state probally changed after that
notification, so it needs to notify rlc state to smu at the end of the
suspend sequence in amdgpu_device_suspend() that can make sure the rlc
state  is correctly set to SMU.

[  101.000590] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[  101.000598] amdgpu 0000:03:00.0: amdgpu: Failed to disable gfxoff!
[  110.838026] amdgpu 0000:03:00.0: amdgpu: SMU: I'm not done with your previous command: SMN_C2PMSG_66:0x0000001E SMN_C2PMSG_82:0x00000000
[  110.838035] amdgpu 0000:03:00.0: amdgpu: Failed to disable smu features.
[  110.838039] amdgpu 0000:03:00.0: amdgpu: Fail to disable dpm features!
[  110.838040] [drm:amdgpu_device_ip_suspend_phase2 [amdgpu]] *ERROR* suspend of IP block <smu> failed -62
[  110.884394] PM: suspend of devices aborted after 21213.620 msecs
[  110.884402] PM: start suspend of devices aborted after 21213.882 msecs
[  110.884405] PM: Some devices failed to suspend, or early wake event detected
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.

[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

GC IP 9.4.2 and up support TA reporting of the number
of xGMI links between peers.
Tested-by: Vignesh Chander <vignesh.chander@amd.com>
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Mukul Joshi <mukul.joshi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.

This means we are unconditionally allowing Z8, the hardware default.

[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

When waiting for the ACK for INBOX0 message,
we have to ensure to include the udelay
for proper wait time

Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pull tracing fixes from Steven Rostedt::
 "Eventfs fixes:

   - With the usage of simple_recursive_remove() recommended by Al Viro,
     the code should not be calling "d_invalidate()" itself. Doing so is
     causing crashes. The code was calling d_invalidate() on the race of
     trying to look up a file while the parent was being deleted. This
     was detected, and the added dentry was having d_invalidate() called
     on it, but the deletion of the directory was also calling
     d_invalidate() on that same dentry.

   - A fix to not free the eventfs_inode (ei) until the last dput() was
     called on its ei->dentry made the ei->dentry exist even after it
     was marked for free by setting the ei->is_freed. But code elsewhere
     still was checking if ei->dentry was NULL if ei->is_freed is set
     and would trigger WARN_ON if that was the case. That's no longer
     true and there should not be any warnings when it is true.

   - Use GFP_NOFS for allocations done under eventfs_mutex. The
     eventfs_mutex can be taken on file system reclaim, make sure that
     allocations done under that mutex do not trigger file system
     reclaim.

   - Clean up code by moving the taking of inode_lock out of the helper
     functions and into where they are needed, and not use the parameter
     to know to take it or not. It must always be held but some callers
     of the helper function have it taken when they were called.

   - Warn if the inode_lock is not held in the helper functions.

   - Warn if eventfs_start_creating() is called without a parent. As
     eventfs is underneath tracefs, all files created will have a parent
     (the top one will have a tracefs parent).

  Tracing update:

   - Add Mathieu Desnoyers as an official reviewer of the tracing subsystem"

* tag 'trace-v6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  MAINTAINERS: TRACING: Add Mathieu Desnoyers as Reviewer
  eventfs: Make sure that parent->d_inode is locked in creating files/dirs
  eventfs: Do not allow NULL parent to eventfs_start_creating()
  eventfs: Move taking of inode_lock into dcache_dir_open_wrapper()
  eventfs: Use GFP_NOFS for allocation when eventfs_mutex is held
  eventfs: Do not invalidate dentry in create_file/dir_dentry()
  eventfs: Remove expectation that ei->is_freed means ei->dentry == NULL

Pull parisc architecture fixes from Helge Deller:
 "This patchset fixes and enforces correct section alignments for the
  ex_table, altinstructions, parisc_unwind, jump_table and bug_table
  which are created by inline assembly.

  Due to not being correctly aligned at link & load time they can
  trigger unnecessarily the kernel unaligned exception handler at
  runtime. While at it, I switched the bug table to use relative
  addresses which reduces the size of the table by half on 64-bit.

  We still had the ENOSYM and EREMOTERELEASE errno symbols as left-overs
  from HP-UX, which now trigger build-issues with glibc. We can simply
  remove them.

  Most of the patches are tagged for stable kernel series.

  Summary:

   - Drop HP-UX ENOSYM and EREMOTERELEASE return codes to avoid glibc
     build issues

   - Fix section alignments for ex_table, altinstructions, parisc unwind
     table, jump_table and bug_table

   - Reduce size of bug_table on 64-bit kernel by using relative
     pointers"

* tag 'parisc-for-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Reduce size of the bug_table on 64-bit kernel by half
  parisc: Drop the HP-UX ENOSYM and EREMOTERELEASE error codes
  parisc: Use natural CPU alignment for bug_table
  parisc: Ensure 32-bit alignment on parisc unwind section
  parisc: Mark lock_aligned variables 16-byte aligned on SMP
  parisc: Mark jump_table naturally aligned
  parisc: Mark altinstructions read-only and 32-bit aligned
  parisc: Mark ex_table entries 32-bit aligned in uaccess.h
  parisc: Mark ex_table entries 32-bit aligned in assembly.h

Pull x86 microcode fixes from Ingo Molnar:
 "Fix/enhance x86 microcode version reporting: fix the bootup log spam,
  and remove the driver version announcement to avoid version confusion
  when distros backport fixes"

* tag 'x86-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Rework early revisions reporting
  x86/microcode: Remove the driver announcement and version

Pull x86 perf event fix from Ingo Molnar:
 "Fix a bug in the Intel hybrid CPUs hardware-capabilities enumeration
  code resulting in non-working events on those platforms"

* tag 'perf-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Correct incorrect 'or' operation for PMU capabilities

Pull locking fix from Ingo Molnar:
 "Fix lockdep block chain corruption resulting in KASAN warnings"

* tag 'locking-urgent-2023-11-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep: Fix block chain corruption

Pull smb client fixes from Steve French:

 - use after free fix in releasing multichannel interfaces

 - fixes for special file types (report char, block, FIFOs properly when
   created e.g. by NFS to Windows)

 - fixes for reporting various special file types and symlinks properly
   when using SMB1

* tag '6.7-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  smb: client: introduce cifs_sfu_make_node()
  smb: client: set correct file type from NFS reparse points
  smb: client: introduce ->parse_reparse_point()
  smb: client: implement ->query_reparse_point() for SMB1
  cifs: fix use after free for iface while disabling secondary channels

Pull USB / PHY / Thunderbolt fixes from Greg KH:
 "Here are a number of reverts, fixes, and new device ids for 6.7-rc3
  for the USB, PHY, and Thunderbolt driver subsystems. Include in here
  are:

   - reverts of some PHY drivers that went into 6.7-rc1 that shouldn't
     have been merged yet, the author is reworking them based on review
     comments as they were using older apis that shouldn't be used
     anymore for newer drivers

   - small thunderbolt driver fixes for reported issues

   - USB driver fixes for a variety of small issues in dwc3, typec,
     xhci, and other smaller drivers.

   - new device ids for usb-serial and onboard_usb_hub drivers.

  All of these have been in linux-next with no reported issues"

* tag 'usb-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  USB: serial: option: add Luat Air72*U series products
  USB: dwc3: qcom: fix ACPI platform device leak
  USB: dwc3: qcom: fix software node leak on probe errors
  USB: dwc3: qcom: fix resource leaks on probe deferral
  USB: dwc3: qcom: simplify wakeup interrupt setup
  USB: dwc3: qcom: fix wakeup after probe deferral
  dt-bindings: usb: qcom,dwc3: fix example wakeup interrupt types
  usb: misc: onboard-hub: add support for Microchip USB5744
  dt-bindings: usb: microchip,usb5744: Add second supply
  usb: misc: ljca: Fix enumeration error on Dell Latitude 9420
  USB: serial: option: add Fibocom L7xx modules
  USB: xhci-plat: fix legacy PHY double init
  usb: typec: tipd: Supply also I2C driver data
  usb: xhci-mtk: fix in-ep's start-split check failure
  usb: dwc3: set the dma max_seg_size
  usb: config: fix iteration issue in 'usb_get_bos_descriptor()'
  usb: dwc3: add missing of_node_put and platform_device_put
  USB: dwc2: write HCINT with INTMASK applied
  usb: misc: ljca: Drop _ADR support to get ljca children devices
  usb: cdnsp: Fix deadlock issue during using NCM gadget
  ...

Pull xfs fix from Chandan Babu:

 - Validate quota records recovered from the log before writing them to
   the disk.

* tag 'xfs-6.7-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: dquot recovery does not validate the recovered dquot
  xfs: clean up dqblk extraction

Pull arm64 fixes from Catalin Marinas:

 - Fix "rodata=on" not disabling "rodata=full" on arm64

 - Add arm64 make dependency between vmlinuz.efi and Image, leading to
   occasional build failures previously (with parallel building)

 - Add newline to the output formatting of the za-fork kselftest

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: add dependency between vmlinuz.efi and Image
  kselftest/arm64: Fix output formatting for za-fork
  arm64: mm: Fix "rodata=on" when CONFIG_RODATA_FULL_DEFAULT_ENABLED=y

Pull xen fixes from Juergen Gross:

 - A small cleanup patch for the Xen privcmd driver

 - A fix for the swiotlb-xen driver which was missing the advertising of
   the maximum mapping length

 - A fix for Xen on Arm for a longstanding bug, which happened to occur
   only recently: a structure in percpu memory crossed a page boundary,
   which was rejected by the hypervisor

* tag 'for-linus-6.7a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  arm/xen: fix xen_vcpu_info allocation alignment
  xen: privcmd: Replace zero-length array with flex-array member and use __counted_by
  swiotlb-xen: provide the "max_mapping_size" method

Enable GENERIC_BUG_RELATIVE_POINTERS which will store 32-bit relative
offsets to the bug address and the source file name instead of 64-bit
absolute addresses. This effectively reduces the size of the
bug_table[] array by half on 64-bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>

Those return codes are only defined for the parisc architecture and
are leftovers from when we wanted to be HP-UX compatible.

They are not returned by any Linux kernel syscall but do trigger
problems with the glibc strerrorname_np() and strerror() functions as
reported in glibc issue #31080.

There is no need to keep them, so simply remove them.
Signed-off-by: Helge Deller <deller@gmx.de>
Reported-by: Bruno Haible <bruno@clisp.org>
Closes: https://sourceware.org/bugzilla/show_bug.cgi?id=31080
Cc: stable@vger.kernel.org

Make sure that the __bug_table section gets 32- or 64-bit aligned,
depending if a 32- or 64-bit kernel is being built.
Mark it non-writeable and use .blockz instead of the .org assembler
directive to pad the struct.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org   # v6.0+