The SA2UL hardware is also used by SYSFW and OP-TEE. It should be
requested using the shared TI-SCI flags instead of the exclusive
flags or the request will fail.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20220823001136.10944-3-afd@ti.com

The first TX and first two RX PSI-L threads for SA2UL are used
by SYSFW on High Security(HS) devices. Use the next available
threads to prevent resource allocation conflicts.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20220823001136.10944-2-afd@ti.com

The hardware random number generator is used by OP-TEE and is access is
denied to other users with SoC level bus firewalls. Any access to this
device from Linux will result in firewall errors.

We could remove this node, but it is still valid device description,
and it is possible it could be re-enabled in the bootloader if OP-TEE
is not used. So only disable this node for now.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20220823001136.10944-1-afd@ti.com

Add DT entries for main domain watchdog instances.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20220822235006.7081-1-afd%40ti.com

The ELM module is used for GPMC NAND accesses for detecting
and correcting errors during reads due to NAND bitflips errors.

4-, 8-, and 16-bit error-correction levels are supported using
the BCH (Bose-ChaudhurI-Hocquenghem) algorithm.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220802104456.11069-3-rogerq@kernel.org

The GPMC is a unified memory controller dedicated for interfacing
with external memory devices like
  - Asynchronous SRAM-like memories and ASICs
  - Asynchronous, synchronous, and page mode burst NOR flash
  - NAND flash
  - Pseudo-SRAM devices
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20220802104456.11069-2-rogerq@kernel.org

The RNG node for this platform claims pka_in_clk. Change it to claim the
correct clock x1_clk. [1]

[1]: https://downloads.ti.com/tisci/esd/latest/5_soc_doc/j721e/clocks.html#clocks-for-sa2-ul0-deviceSigned-off-by: Daniel Parks <danielrparks@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/f29e2c65dc7310a926af8a676651592afac04b03.1659981162.git.danielrparks@ti.com

Add the node for SA2UL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[s-anna@ti.com: drop label, minor cleanups]
Signed-off-by: Suman Anna <s-anna@ti.com>
[j-choudhary@ti.com: disable rng-node, change flag to shared]
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20220711085743.10128-3-j-choudhary@ti.com

Add the address space for the SA2UL in MAIN domain to the ranges property
of the cbass_main interconnect node so that the addresses within the
corresponding sram nodes and its children can be translated properly by
the relevant OF address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20220711085743.10128-2-j-choudhary@ti.com

Makes it easier to reference the node in board dts files.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20220822095943.18563-1-christian.gmeiner@gmail.com

Use alphabetical sort to organize the SoCs
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220830160507.7726-3-nm@ti.com

Use alphabetical sort to organize the am654 board names.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220830160507.7726-2-nm@ti.com

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well

Pull more cifs updates from Steve French:

 - two fixes for stable, one for a lock length miscalculation, and
   another fixes a lease break timeout bug

 - improvement to handle leases, allows the close timeout to be
   configured more safely

 - five restructuring/cleanup patches

* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
  cifs: Add constructor/destructors for tcon->cfid
  SMB3: fix lease break timeout when multiple deferred close handles for the same file.
  smb3: allow deferred close timeout to be configurable
  cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
  cifs: Move cached-dir functions into a separate file
  cifs: Remove {cifs,nfs}_fscache_release_page()
  cifs: fix lock length calculation

Enable multipage folio support for the afs filesystem.

Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.

Note that it does require a change to afs_write_begin() to return the
correct subpage.  This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Ingo Molnar:
 "Misc timer fixes:

   - fix a potential use-after-free bug in posix timers

   - correct a prototype

   - address a build warning"

* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-cpu-timers: Cleanup CPU timers before freeing them during exec
  time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
  posix-timers: Make do_clock_gettime() static

Pull x86 fix from Ingo Molnar:
 "Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
  turned on by default), which also need STIBP enabled (if available) to
  be '100% safe' on even the shortest speculation windows"

* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/bugs: Enable STIBP for IBPB mitigated RETBleed

Pull more i2c updates from Wolfram Sang:

 - two driver fixes for issues introduced this cycle

 - one trivial driver improvement regarding ACPI

 - more DTS conversion and additions

 - documentation updates

 - subsystem-wide move from strlcpy to strscpy

* tag 'i2c-for-5.20-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  docs: i2c: i2c-sysfs: fix hyperlinks
  docs: i2c: i2c-sysfs: improve wording
  docs: i2c: instantiating-devices: add syntax coloring to dts and C blocks
  docs: i2c: smbus-protocol: improve DataLow/DataHigh definition
  docs: i2c: i2c-protocol: remove unused legend items
  docs: i2c: i2c-protocol,smbus-protocol: remove nonsense words
  docs: i2c: i2c-protocol: update introductory paragraph
  i2c: move core from strlcpy to strscpy
  i2c: move drivers from strlcpy to strscpy
  i2c: kempld: Support ACPI I2C device declaration
  i2c: mediatek: add i2c compatible for MT8188
  dt-bindings: i2c: update bindings for mt8188 soc
  i2c: microchip-corei2c: fix erroneous late ack send
  dt-bindings: i2c: qcom,i2c-cci: convert to dtschema
  i2c: qcom-geni: Fix GPI DMA buffer sync-back

Pull NTB updates from Jon Mason:
 "Non-Transparent Bridge updates.

  Fix of heap data and clang warnings, support for a new Intel NTB
  device, and NTB EndPoint Function (EPF) support and the various fixes
  for that"

* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
  MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
  NTB: EPF: Tidy up some bounds checks
  NTB: EPF: Fix error code in epf_ntb_bind()
  PCI: endpoint: pci-epf-vntb: reduce several globals to statics
  PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
  PCI: endpoint: Fix Kconfig dependency
  NTB: EPF: set pointer addr to null using NULL rather than 0
  Documentation: PCI: extend subheading underline for "lspci output" section
  Documentation: PCI: Use code-block block for scratchpad registers diagram
  Documentation: PCI: Add specification for the PCI vNTB function device
  PCI: endpoint: Support NTB transfer between RC and EP
  NTB: epf: Allow more flexibility in the memory BAR map method
  PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
  ntb: intel: add GNR support for Intel PCIe gen5 NTB
  NTB: ntb_tool: uninitialized heap data in tool_fn_write()
  ntb: idt: fix clang -Wformat warnings

Pull more xfs updates from Darrick Wong:
 "There's not a lot this time around, just the usual bug fixes and
  corrections for missing error returns.

   - Return error codes from block device flushes to userspace

   - Fix a deadlock between reclaim and mount time quotacheck

   - Fix an unnecessary ENOSPC return when doing COW on a filesystem
     with severe free space fragmentation

   - Fix a miscalculation in the transaction reservation computations
     for file removal operations"

* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix inode reservation space for removing transaction
  xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
  xfs: fix intermittent hang during quotacheck
  xfs: check return codes when flushing block devices

Pull more SCSI updates from James Bottomley:
 "Mostly small bug fixes and trivial updates.

  The major new core update is a change to the way device, target and
  host reference counting is done to try to make it more robust (this
  change has soaked for a while to try to winkle out any bugs)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: pm8001: Fix typo 'the the' in comment
  scsi: megaraid_sas: Remove redundant variable cmd_type
  scsi: FlashPoint: Remove redundant variable bm_int_st
  scsi: zfcp: Fix missing auto port scan and thus missing target ports
  scsi: core: Call blk_mq_free_tag_set() earlier
  scsi: core: Simplify LLD module reference counting
  scsi: core: Make sure that hosts outlive targets
  scsi: core: Make sure that targets outlive devices
  scsi: ufs: ufs-pci: Correct check for RESET DSM
  scsi: target: core: De-RCU of se_lun and se_lun acl
  scsi: target: core: Fix race during ACL removal
  scsi: ufs: core: Correct ufshcd_shutdown() flow
  scsi: ufs: core: Increase the maximum data buffer size
  scsi: lpfc: Check the return value of alloc_workqueue()

Pull block fixes from Jens Axboe:

 - NVMe pull request
     - print nvme connect Linux error codes properly (Amit Engel)
     - fix the fc_appid_store return value (Christoph Hellwig)
     - fix a typo in an error message (Christophe JAILLET)
     - add another non-unique identifier quirk (Dennis P. Kliem)
     - check if the queue is allocated before stopping it in nvme-tcp
       (Maurizio Lombardi)
     - restart admin queue if the caller needs to restart queue in
       nvme-fc (Ming Lei)
     - use kmemdup instead of kmalloc + memcpy in nvme-auth (Zhang
       Xiaoxu)

 - __alloc_disk_node() error handling fix (Rafael)

* tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block:
  block: Do not call blk_put_queue() if gendisk allocation fails
  nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S70
  nvme-tcp: check if the queue is allocated before stopping it
  nvme-fabrics: Fix a typo in an error message
  nvme-fabrics: parse nvme connect Linux error codes
  nvmet-auth: use kmemdup instead of kmalloc + memcpy
  nvme-fc: fix the fc_appid_store return value
  nvme-fc: restart admin queue if the caller needs to restart queue

Pull io_uring fixes from Jens Axboe:

 - Regression fix for this merge window, fixing a wrong order of
   arguments for io_req_set_res() for passthru (Dylan)

 - Fix for the audit code leaking context memory (Peilin)

 - Ensure that provided buffers are memcg accounted (Pavel)

 - Correctly handle short zero-copy sends (Pavel)

 - Sparse warning fixes for the recvmsg multishot command (Dylan)

 - Error handling fix for passthru (Anuj)

 - Remove randomization of struct kiocb fields, to avoid it growing in
   size if re-arranged in such a fashion that it grows more holes or
   padding (Keith, Linus)

 - Small series improving type safety of the sqe fields (Stefan)

* tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block:
  io_uring: add missing BUILD_BUG_ON() checks for new io_uring_sqe fields
  io_uring: make io_kiocb_to_cmd() typesafe
  fs: don't randomize struct kiocb fields
  io_uring: consistently make use of io_notif_to_data()
  io_uring: fix error handling for io_uring_cmd
  io_uring: fix io_recvmsg_prep_multishot sparse warnings
  io_uring/net: send retry for zerocopy
  io_uring: mem-account pbuf buckets
  audit, io_uring, io-wq: Fix memory leak in io_sq_thread() and io_wqe_worker()
  io_uring: pass correct parameters to io_req_set_res

This is a prelude to adding more tests to shell tests and in order to
support putting those tests into subdirectories, I need to change the
test code that scans/finds and runs them.

To support subdirs I have to recurse so it's time to refactor the code
to allow this and centralize the shell script finding into one location
and only one single scan that builds a list of all the found tests in
memory instead of it being duplicated in 3 places.

This code also optimizes things like knowing the max width of desciption
strings (as we can do that while we scan instead of a whole new pass of
opening files).

It also more cleanly filters scripts to see only *.sh files thus
skipping random other files in directories like *~ backup files, other
random junk/data files that may appear and the scripts must be
executable to make the cut (this ensures the script lib dir is not seen
as scripts to run).

This avoids perf test running previous older versions of test scripts
that are editor backup files as well as skipping perf.data files that
may appear and so on.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight@lists.linaro.org
Link: https://lore.kernel.org/r/20220812121641.336465-2-carsten.haitzler@foss.arm.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v1.20, update events for snowridgex by the latest
event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the snowridgex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-12-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v1.28, the metrics are based on TMA 4.4 full, update
events and metrics for skylakex by the latest event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the skylakex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-11-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
sapphirerapids.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the sapphirerapids files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-10-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v9, update events for knightslanding by the latest
event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the knightslanding files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-9-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
jaketown.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the jaketown files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-8-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The metrics are based on TMA 4.4 full, add new metrics “UNCORE_FREQ” for
ivytown.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the ivytown files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-7-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v1.15, the metrics are based on TMA 4.4 full, update
events and metrics for icelakex by the latest event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the icelakex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-6-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update the events to v25, the metrics are based on TMA 4.4 full, update
events and metrics for haswellx by the latest event converter tools.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the haswellx files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-5-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Update to v16, the metrics are based on TMA 4.4 full, update events and add
new metrics “UNCORE_FREQ” for cascadelakex.

Use script at:
https://github.com/intel/event-converter-for-linux-perf/blob/master/download_and_gen.py

to download and generate the latest events and metrics. Manually copy
the cascadelakex files into perf.
Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Tested-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220812085239.3089231-4-zhengjun.xing@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>