This patch adds a new msk->flags bit MPTCP_FAIL_NO_RESPONSE, then reuses
sk_timer to trigger a check if we have not received a response from the
peer after sending MP_FAIL. If the peer doesn't respond properly, reset
the subflow.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new struct member mp_fail_response_expect in struct
mptcp_subflow_context to support MP_FAIL response. In the single subflow
with checksum error and contiguous data special case, a MP_FAIL is sent
in response to another MP_FAIL.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mptcp_data_lock() needs to be held when manipulating the msk
retransmit_timer or the sk sk_timer. This patch adds the data
lock for the both timers.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the helper mptcp_stop_timer() instead of using sk_stop_timer() to
stop icsk_retransmit_timer directly.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the single subflow test case for MP_FAIL, to test the infinite
mapping case. Use the test_linkfail value to make 128KB test files.

Add a new function reset_with_fail(), in it use 'iptables' and 'tc
action pedit' rules to produce the bit flips to trigger the checksum
failures. Set validate_checksum to enable checksums for the MP_FAIL
tests without passing the '-C' argument. Set check_invert flag to
enable the invert bytes check for the output data in check_transfer().
Instead of the file mismatch error, this test prints out the inverted
bytes.

Add a new function pedit_action_pkts() to get the numbers of the packets
edited by the tc pedit actions. Print this numbers to the output.

Also add the needed kernel configures in the selftests config file.
Suggested-by: Davide Caratti <dcaratti@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix spelling in comment.

Fixes: 94abdad6 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Link: https://lore.kernel.org/r/20220425154856.169499-1-marcel@ziswiler.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The only remaining definitions of __SLOW_DOWN_IO (for alpha and ia64) do
nothing, and the only mentions in networking are in comments.  Remove these
mentions.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

atp.h is included only by atp.c, which does not use eeprom_delay().  Remove
the unused definition.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When NIC takes care of crypto (or the record has already
been decrypted) we forget to update darg->async. ->async
is supposed to mean whether record is async capable on
input and whether record has been queued for async crypto
on output.
Reported-by: Gal Pressman <gal@nvidia.com>
Fixes: 3547a1f9 ("tls: rx: use async as an in-out argument")
Tested-by: Gal Pressman <gal@nvidia.com>
Link: https://lore.kernel.org/r/20220425233309.344858-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Golle reports that the conversion of mt753x to phylink PCS caused
an oops as below.

The problem is with the placement of the PCS initialisation, which
occurs after mt7531_setup() has been called. However, burited in this
function is a call to setup the CPU port, which requires the PCS
structure to be already setup.

Fix this by changing the initialisation order.

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020
Mem abort info:
  ESR = 0x96000005
  EC = 0x25: DABT (current EL), IL = 32 bits
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
  FSC = 0x05: level 1 translation fault
Data abort info:
  ISV = 0, ISS = 0x00000005
  CM = 0, WnR = 0
user pgtable: 4k pages, 39-bit VAs, pgdp=0000000046057000
[0000000000000020] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
Internal error: Oops: 96000005 [#1] SMP
Modules linked in:
CPU: 0 PID: 32 Comm: kworker/u4:1 Tainted: G S 5.18.0-rc3-next-20220422+ #0
Hardware name: Bananapi BPI-R64 (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mt7531_cpu_port_config+0xcc/0x1b0
lr : mt7531_cpu_port_config+0xc0/0x1b0
sp : ffffffc008d5b980
x29: ffffffc008d5b990 x28: ffffff80060562c8 x27: 00000000f805633b
x26: ffffff80001a8880 x25: 00000000000009c4 x24: 0000000000000016
x23: ffffff8005eb6470 x22: 0000000000003600 x21: ffffff8006948080
x20: 0000000000000000 x19: 0000000000000006 x18: 0000000000000000
x17: 0000000000000001 x16: 0000000000000001 x15: 02963607fcee069e
x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101
x11: ffffffc037302000 x10: 0000000000000870 x9 : ffffffc008d5b800
x8 : ffffff800028f950 x7 : 0000000000000001 x6 : 00000000662b3000
x5 : 00000000000002f0 x4 : 0000000000000000 x3 : ffffff800028f080
x2 : 0000000000000000 x1 : ffffff800028f080 x0 : 0000000000000000
Call trace:
 mt7531_cpu_port_config+0xcc/0x1b0
 mt753x_cpu_port_enable+0x24/0x1f0
 mt7531_setup+0x49c/0x5c0
 mt753x_setup+0x20/0x31c
 dsa_register_switch+0x8bc/0x1020
 mt7530_probe+0x118/0x200
 mdio_probe+0x30/0x64
 really_probe.part.0+0x98/0x280
 __driver_probe_device+0x94/0x140
 driver_probe_device+0x40/0x114
 __device_attach_driver+0xb0/0x10c
 bus_for_each_drv+0x64/0xa0
 __device_attach+0xa8/0x16c
 device_initial_probe+0x10/0x20
 bus_probe_device+0x94/0x9c
 deferred_probe_work_func+0x80/0xb4
 process_one_work+0x200/0x3a0
 worker_thread+0x260/0x4c0
 kthread+0xd4/0xe0
 ret_from_fork+0x10/0x20
Code: 9409e911 937b7e60 8b0002a0 f9405800 (f9401005)
---[ end trace 0000000000000000 ]---
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Fixes: cbd1f243 ("net: dsa: mt7530: partially convert to phylink_pcs")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1nj6FW-007WZB-5Y@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Logic added in commit f35f8219 ("tcp: defer skb freeing after socket
lock is released") helped bulk TCP flows to move the cost of skbs
frees outside of critical section where socket lock was held.

But for RPC traffic, or hosts with RFS enabled, the solution is far from
being ideal.

For RPC traffic, recvmsg() has to return to user space right after
skb payload has been consumed, meaning that BH handler has no chance
to pick the skb before recvmsg() thread. This issue is more visible
with BIG TCP, as more RPC fit one skb.

For RFS, even if BH handler picks the skbs, they are still picked
from the cpu on which user thread is running.

Ideally, it is better to free the skbs (and associated page frags)
on the cpu that originally allocated them.

This patch removes the per socket anchor (sk->defer_list) and
instead uses a per-cpu list, which will hold more skbs per round.

This new per-cpu list is drained at the end of net_action_rx(),
after incoming packets have been processed, to lower latencies.

In normal conditions, skbs are added to the per-cpu list with
no further action. In the (unlikely) cases where the cpu does not
run net_action_rx() handler fast enough, we use an IPI to raise
NET_RX_SOFTIRQ on the remote cpu.

Also, we do not bother draining the per-cpu list from dev_cpu_dead()
This is because skbs in this list have no requirement on how fast
they should be freed.

Note that we can add in the future a small per-cpu cache
if we see any contention on sd->defer_lock.

Tested on a pair of hosts with 100Gbit NIC, RFS enabled,
and /proc/sys/net/ipv4/tcp_rmem[2] tuned to 16MB to work around
page recycling strategy used by NIC driver (its page pool capacity
being too small compared to number of skbs/pages held in sockets
receive queues)

Note that this tuning was only done to demonstrate worse
conditions for skb freeing for this particular test.
These conditions can happen in more general production workload.

10 runs of one TCP_STREAM flow

Before:
Average throughput: 49685 Mbit.

Kernel profiles on cpu running user thread recvmsg() show high cost for
skb freeing related functions (*)

    57.81%  [kernel]       [k] copy_user_enhanced_fast_string
(*) 12.87%  [kernel]       [k] skb_release_data
(*)  4.25%  [kernel]       [k] __free_one_page
(*)  3.57%  [kernel]       [k] __list_del_entry_valid
     1.85%  [kernel]       [k] __netif_receive_skb_core
     1.60%  [kernel]       [k] __skb_datagram_iter
(*)  1.59%  [kernel]       [k] free_unref_page_commit
(*)  1.16%  [kernel]       [k] __slab_free
     1.16%  [kernel]       [k] _copy_to_iter
(*)  1.01%  [kernel]       [k] kfree
(*)  0.88%  [kernel]       [k] free_unref_page
     0.57%  [kernel]       [k] ip6_rcv_core
     0.55%  [kernel]       [k] ip6t_do_table
     0.54%  [kernel]       [k] flush_smp_call_function_queue
(*)  0.54%  [kernel]       [k] free_pcppages_bulk
     0.51%  [kernel]       [k] llist_reverse_order
     0.38%  [kernel]       [k] process_backlog
(*)  0.38%  [kernel]       [k] free_pcp_prepare
     0.37%  [kernel]       [k] tcp_recvmsg_locked
(*)  0.37%  [kernel]       [k] __list_add_valid
     0.34%  [kernel]       [k] sock_rfree
     0.34%  [kernel]       [k] _raw_spin_lock_irq
(*)  0.33%  [kernel]       [k] __page_cache_release
     0.33%  [kernel]       [k] tcp_v6_rcv
(*)  0.33%  [kernel]       [k] __put_page
(*)  0.29%  [kernel]       [k] __mod_zone_page_state
     0.27%  [kernel]       [k] _raw_spin_lock

After patch:
Average throughput: 73076 Mbit.

Kernel profiles on cpu running user thread recvmsg() looks better:

    81.35%  [kernel]       [k] copy_user_enhanced_fast_string
     1.95%  [kernel]       [k] _copy_to_iter
     1.95%  [kernel]       [k] __skb_datagram_iter
     1.27%  [kernel]       [k] __netif_receive_skb_core
     1.03%  [kernel]       [k] ip6t_do_table
     0.60%  [kernel]       [k] sock_rfree
     0.50%  [kernel]       [k] tcp_v6_rcv
     0.47%  [kernel]       [k] ip6_rcv_core
     0.45%  [kernel]       [k] read_tsc
     0.44%  [kernel]       [k] _raw_spin_lock_irqsave
     0.37%  [kernel]       [k] _raw_spin_lock
     0.37%  [kernel]       [k] native_irq_return_iret
     0.33%  [kernel]       [k] __inet6_lookup_established
     0.31%  [kernel]       [k] ip6_protocol_deliver_rcu
     0.29%  [kernel]       [k] tcp_rcv_established
     0.29%  [kernel]       [k] llist_reverse_order

v2: kdoc issue (kernel bots)
    do not defer if (alloc_cpu == smp_processor_id()) (Paolo)
    replace the sk_buff_head with a single-linked list (Jakub)
    add a READ_ONCE()/WRITE_ONCE() for the lockless read of sd->defer_list
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220422201237.416238-1-eric.dumazet@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

add support for Sierra Wireless EM7590 0xc081 composition.
Signed-off-by: Ethan Yang <etyang@sierrawireless.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220425054028.5444-1-etyang@sierrawireless.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Currently, the kernel drops GSO VLAN tagged packet if it's created with
socket(AF_PACKET, SOCK_RAW, 0) plus virtio_net_hdr.

The reason is AF_PACKET doesn't adjust the skb network header if there is
a VLAN tag. Then after virtio_net_hdr_set_proto() called, the skb->protocol
will be set to ETH_P_IP/IPv6. And in later inet/ipv6_gso_segment() the skb
is dropped as network header position is invalid.

Let's handle VLAN packets by adjusting network header position in
packet_parse_headers(). The adjustment is safe and does not affect the
later xmit as tap device also did that.

In packet_snd(), packet_parse_headers() need to be moved before calling
virtio_net_hdr_set_proto(), so we can set correct skb->protocol and
network header first.

There is no need to update tpacket_snd() as it calls packet_parse_headers()
in tpacket_fill_skb(), which is already before calling virtio_net_hdr_*
functions.

skb->no_fcs setting is also moved upper to make all skb settings together
and keep consistency with function packet_sendmsg_spkt().
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20220425014502.985464-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The ksz8795 and ksz9477 uses the same algorithm for the
port_stp_state_set function except the register address is different. So
moved the algorithm to the ksz_common.c and used the dev_ops for
register read and write. This function can also used for the lan937x
part. Hence making it generic for all the parts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424112831.11504-1-arun.ramadoss@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Added the config_intr and handle_interrupt for the LAN937x phy which is
same as the LAN87xx phy.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220423154727.29052-1-arun.ramadoss@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Flushing system-wide workqueues is dangerous and will be forbidden.
Replace system_wq with local wwan_wq.

While we are at it, make err_clean_devs: label of wwan_hwsim_init()
behave like wwan_hwsim_exit(), for it is theoretically possible to call
wwan_hwsim_debugfs_devcreate_write()/wwan_hwsim_debugfs_devdestroy_write()
by the moment wwan_hwsim_init_devs() returns.

Link: https://lkml.kernel.org/r/49925af7-78a8-a3dd-bce6-cfc02e1a9236@I-love.SAKURA.ne.jpSigned-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/7390d51f-60e2-3cee-5277-b819a55ceabe@I-love.SAKURA.ne.jpSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Reduce a number of included headers to a necessary minimum.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/ipv4/arp.c:1412:36: warning: unused variable 'arp_seq_ops' [-Wunused-const-variable]

Add #ifdef CONFIG_PROC_FS for 'arp_seq_ops'.

Fixes: e968b1b3 ("arp: Remove #ifdef CONFIG_PROC_FS")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

The aggregation byte limit for an endpoint is currently computed
based on the endpoint's receive buffer size.

However, some bytes at the front of each receive buffer are reserved
on the assumption that--as with SKBs--it might be useful to insert
data (such as headers) before what lands in the buffer.

The aggregation byte limit currently doesn't take into account that
reserved space, and as a result, aggregation could require space
past that which is available in the buffer.

Fix this by reducing the size used to compute the aggregation byte
limit by the NET_SKB_PAD offset reserved for each receive buffer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check if the kzalloc() failed.

Fixes: 804775df ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the BUG_ON() with returning error code to handle
the fault more gracefully.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

payload only memset but no use at all, so we drop them.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: extend line card model by devices and info

Jiri says:

This patchset is extending the line card model by three items:
1) line card devices
2) line card info
3) line card device info

First three patches are introducing the necessary changes in devlink
core.

Then, all three extensions are implemented in mlxsw alongside with
selftest.

Examples:
$ devlink lc show pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8 state active type 16x100G
    supported_types:
      16x100G
    devices:
      device 0
      device 1
      device 2
      device 3
$ devlink lc info pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8
    versions:
        fixed:
          hw.revision 0
        running:
          ini.version 4
    devices:
      device 0
        versions:
            running:
              fw 19.2010.1310
      device 1
        versions:
            running:
              fw 19.2010.1310
      device 2
        versions:
            running:
              fw 19.2010.1310
      device 3
        versions:
            running:
              fw 19.2010.1310

Note that device FW flashing is going to be implemented in the follow-up
patchset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Once line card is activated, check the device FW version is exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend MDDQ to obtain FW version of line card device and implement
device_info_get() op to fill up the info with that.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add FW version fields to MDDQ device_info.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once line card is provisioned, check if HW revision and INI version
are exposed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once line card is provisioned, check the count of devices on it and
print them out.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the line card is provisioned, go over all possible existing
devices (gearboxes) on it and attach them, so devlink core is aware of
them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend existing MDDQ register by possibility to query information about
devices residing on a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the line card info message with information (e.g., FW version)
about devices found on the line card.

Example:
$ devlink lc info pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8
    versions:
        fixed:
          hw.revision 0
        running:
          ini.version 4
    devices:
      device 0
        versions:
            running:
              fw 19.2010.1310
      device 1
        versions:
            running:
              fw 19.2010.1310
      device 2
        versions:
            running:
              fw 19.2010.1310
      device 3
        versions:
            running:
              fw 19.2010.1310
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the driver to provide per line card info get op to fill-up info,
similar to the "devlink dev info".

Example:

$ devlink lc info pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8
    versions:
        fixed:
          hw.revision 0
        running:
          ini.version 4
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Line card can contain one or more devices that makes sense to make
visible to the user. For example, this can be a gearbox with
flash memory, which could be updated.

Provide the driver possibility to attach such devices to a line card
and expose those to user.

Example:
$ devlink lc show pci/0000:01:00.0 lc 8
pci/0000:01:00.0:
  lc 8 state active type 16x100G
    supported_types:
      16x100G
    devices:
      device 0
      device 1
      device 2
      device 3
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
DSA selftests

When working on complex new features or reworks it becomes increasingly
difficult to ensure there aren't regressions being introduced, and
therefore it would be nice if we could go over the functionality we
already have and write some tests for it.

Verbally I know from Tobias Waldekranz that he has been working on some
selftests for DSA, yet I have never seen them, so here I am adding some
tests I have written which have been useful for me. The list is by no
means complete (it only covers elementary functionality), but it's still
good to have as a starting point. I also borrowed some refactoring
changes from Joachim Wiberg that he submitted for his "net: bridge:
forwarding of unknown IPv4/IPv6/MAC BUM traffic" series, but not the
entirety of his selftests. I now think that his selftests have some
overlap with bridge_vlan_unaware.sh and bridge_vlan_aware.sh and they
should be more tightly integrated with each other - yet I didn't do that
either :). Another issue I had with his selftests was that they jumped
straight ahead to configure brport flags on br0 (a radical new idea
still at RFC status) while we have bigger problems, and we don't have
nearly enough coverage for the *existing* functionality.

One idea introduced here which I haven't seen before is the symlinking
of relevant forwarding selftests to the selftests/drivers/net/<my-driver>/
folder, plus a forwarding.config file. I think there's some value in
having things structured this way, since the forwarding dir has so many
selftests that aren't relevant to DSA that it is a bit difficult to find
the ones that are.

While searching for applications that I could use for multicast testing
(not my domain of interest/knowledge really), I found Joachim Wiberg's
mtools, mcjoin and omping, and I tried them all with various degrees of
success. In particular, I was going to use mcjoin, but I faced some
issues getting IPv6 multicast traffic to work in a VRF, and I bothered
David Ahern about it here:
https://lore.kernel.org/netdev/97eaffb8-2125-834e-641f-c99c097b6ee2@gmail.com/t/
It seems that the problem is that this application should use
SO_BINDTODEVICE, yet it doesn't.

So I ended up patching the bare-bones mtools (msend, mreceive) forked by
Joachim from the University of Virginia's Multimedia Networks Group to
include IPv6 support, and to use SO_BINDTODEVICE. This is what I'm using
now for IPv6.

Note that mausezahn doesn't appear to do a particularly good job of
supporting IPv6 really, and I needed a program to emit the actual
IP_ADD_MEMBERSHIP calls, for dev_mc_add(), so I could test RX filtering.
Crafting the IGMP/MLD reports by hand doesn't really do the trick.
While extremely bare-bones, the mreceive application now seems to do
what I need it to.

Feedback appreciated, it is very likely that I could have done things in
a better way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds an initial subset of forwarding selftests which I considered
to be relevant for DSA drivers, along with a forwarding.config that
makes it easier to run them (disables veth pair creation, makes sure MAC
addresses are unique and stable).

The intention is to request driver writers to run these selftests during
review and make sure that the tests pass, or at least that the problems
are known.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This tests the capability of switch ports to filter out undesired
traffic. Different drivers are expected to have different capabilities
here (so some may fail and some may pass), yet the test still has some
value, for example to check for regressions.

There are 2 kinds of failures, one is when a packet which should have
been accepted isn't (and that should be fixed), and the other "failure"
(as reported by the test) is when a packet could have been filtered out
(for being unnecessary) yet it was received.

The bridge driver fares particularly badly at this test:

TEST: br0: Unicast IPv4 to primary MAC address                      [ OK ]
TEST: br0: Unicast IPv4 to macvlan MAC address                      [ OK ]
TEST: br0: Unicast IPv4 to unknown MAC address                      [FAIL]
        reception succeeded, but should have failed
TEST: br0: Unicast IPv4 to unknown MAC address, promisc             [ OK ]
TEST: br0: Unicast IPv4 to unknown MAC address, allmulti            [FAIL]
        reception succeeded, but should have failed
TEST: br0: Multicast IPv4 to joined group                           [ OK ]
TEST: br0: Multicast IPv4 to unknown group                          [FAIL]
        reception succeeded, but should have failed
TEST: br0: Multicast IPv4 to unknown group, promisc                 [ OK ]
TEST: br0: Multicast IPv4 to unknown group, allmulti                [ OK ]
TEST: br0: Multicast IPv6 to joined group                           [ OK ]
TEST: br0: Multicast IPv6 to unknown group                          [FAIL]
        reception succeeded, but should have failed
TEST: br0: Multicast IPv6 to unknown group, promisc                 [ OK ]
TEST: br0: Multicast IPv6 to unknown group, allmulti                [ OK ]

mainly because it does not implement IFF_UNICAST_FLT. Yet I still think
having the test (with the failures) is useful in case somebody wants to
tackle that problem in the future, to make an easy before-and-after
comparison.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bombard a standalone switch port with various kinds of traffic to ensure
it is really standalone and doesn't leak packets to other switch ports.
Also check for switch ports in different bridges, and switch ports in a
VLAN-aware bridge but having different pvids. No forwarding should take
place in either case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pinging an IPv6 link-local multicast address selects the link-local
unicast address of the interface as source, and we'd like to monitor for
that in tcpdump.

Add a helper to the forwarding library which retrieves the link-local
IPv6 address of an interface, to make that task easier.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the forwarding library with calls to some small C programs which
join an IP multicast group and send some packets to it. Both IPv4 and
IPv6 groups are supported. Use cases range from testing IGMP/MLD
snooping, to RX filtering, to multicast routing.

Testing multicast traffic using msend/mreceive is intended to be done
using tcpdump.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>