- 03 Sep, 2013 11 commits
-
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Nilesh Javali authored
While loopback diagnostic is in progress, disable the ACB which resets all the active connections to target. Disable ACB would filter out all the DHCP multicast and broadcast packets which otherwise cause the diagnostic test to take longer time to complete or failures in some other cases. Signed-off-by:
Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Sreekanth Reddy authored
Signed-off-by:
Sreekanth Reddy <Sreekanth.Reddy@lsi.com> Signed-off-by:
-
Sreekanth Reddy authored
[SCSI] mpt2sas: Fix for kernel panic when driver loads with HBA connected to non LUN 0 configured expander With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created then SCSI scan procedure calls target_alloc, slave_alloc call back functions for LUN 0 and slave_destory() for same LUN 0. In these kind of cases within slave_destroy, pointer to scsi_target in _sas_device structure is set to NULL, following which when slave_alloc for LUN 1 is called then starget would not be set properly for this LUN. So, scsi_target pointer pointing to NULL value would lead to a crash later in the discovery procedure. To solve this issue set the sas_device's scsi_target pointer to scsi_device's scsi_target if it is NULL earlier in slave_alloc callback function. Signed-off-by:
-
Sreekanth Reddy authored
[SCSI] mpt2sas: when Async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed When Async scanning mode is enabled and device scanning is in progress then devices should not be removed. But in actuality, devices are removed but their transport layer entries are not removed. This causes error to add the same device to the transport layer after host reset or diagnostic reset. So, in this patch, modified the code in such a way that device is not removed when Async scanning mode is enabled and device scanning is in progress. Signed-off-by:
-
Sreekanth Reddy authored
Infinite loop can occur if IOCStatus is not equal to MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions _scsih_search_responding_sas_devices, _scsih_search_responding_raid_devices and _scsih_search_responding_expanders So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value, in this patch code is modified to check for IOCStatus not equals to MPI2_IOCSTATUS_SUCCESS to break the while loop. Signed-off-by:
-
Sreekanth Reddy authored
The copyright in driver sources is updated for the year 2013. Signed-off-by:
-
Sreekanth Reddy authored
Change set in MPI2 Rev x specification and 2.00.26 header files 1. Added two new AbortType values for TargetModeAbort Request: one to abort all IOs from a single initiator and other to abort only Command IUs. 2. Added Use Slot Information during Port Enable Event Reply flag to the Flags field of Manufacturing Page 7. 3. Added OEM Identifier to BiosOptions bits of BIOS Page 1. Signed-off-by:
-
Sreekanth Reddy authored
The intent of this patch is to perform a graceful shutdown of target drives even if volume doesn't exits. Changes done in this patch 1. Removed the check for the presence of volumes before sending down MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED. Therefore, this RAID action would be sent if the card is IR Firmware. 2. The MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED is sent even when the system undergoes suspend (in addition to remove/shutdown which was already present) Signed-off-by:
-
Sreekanth Reddy authored
Added a check to identify if mpi_reply is NULL in mpt2sas_ctl_event_callback() and return without proceeding if it is the case. Also modified the following functions to return void instead of 0 or 1 as returning those values from events perspective doesn't make sense. * _base_async_event() * mpt2sas_ctl_event_callback() * mpt2sas_scsih_event_callback() Signed-off-by:
-
- 26 Aug, 2013 21 commits
-
-
John Kacur authored
section Signed-off-by: John Kacur <jkacur@redhat.com> On a 3.6-rt (real-time patch) kernel we are seeing the following BUG However, it appears to be relevant for non-realtime (mainline) as well. [ 49.688847] hpsa 0000:03:00.0: hpsa0: <0x323a> at IRQ 67 using DAC [ 49.749928] scsi0 : hpsa [ 49.784437] BUG: using smp_processor_id() in preemptible [00000000 00000000] code: kworker/u:0/6 [ 49.784465] caller is enqueue_cmd_and_start_io+0x5a/0x100 [hpsa] [ 49.784468] Pid: 6, comm: kworker/u:0 Not tainted 3.6.11.5-rt37.52.el6rt.x86_64.debug #1 [ 49.784471] Call Trace: [ 49.784512] [<ffffffff812abe83>] debug_smp_processor_id+0x123/0x150 [ 49.784520] [<ffffffffa009043a>] enqueue_cmd_and_start_io+0x5a/0x100 [hpsa] [ 49.784529] [<ffffffffa00905cb>] hpsa_scsi_do_simple_cmd_core+0xeb/0x110 [hpsa] [ 49.784537] [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30 [ 49.784544] [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30 [ 49.784553] [<ffffffffa0090701>] hpsa_scsi_do_simple_cmd_with_retry+0x91/0x280 [hpsa] [ 49.784562] [<ffffffffa0093558>] hpsa_scsi_do_report_luns.clone.2+0xd8/0x130 [hpsa] [ 49.784571] [<ffffffffa00935ea>] hpsa_gather_lun_info.clone.3+0x3a/0x1a0 [hpsa] [ 49.784580] [<ffffffffa00963df>] hpsa_update_scsi_devices+0x11f/0x4f0 [hpsa] [ 49.784592] [<ffffffff81592019>] ? sub_preempt_count+0xa9/0xe0 [ 49.784601] [<ffffffffa00968ad>] hpsa_scan_start+0xfd/0x150 [hpsa] [ 49.784613] [<ffffffff8158cba8>] ? rt_spin_lock_slowunlock+0x78/0x90 [ 49.784626] [<ffffffff813b04d7>] do_scsi_scan_host+0x37/0xa0 [ 49.784632] [<ffffffff813b05da>] do_scan_async+0x1a/0x30 [ 49.784643] [<ffffffff8107c4ab>] async_run_entry_fn+0x9b/0x1d0 [ 49.784655] [<ffffffff8106ae92>] process_one_work+0x1f2/0x620 [ 49.784661] [<ffffffff8106ae20>] ? process_one_work+0x180/0x620 [ 49.784668] [<ffffffff8106d4fe>] ? worker_thread+0x5e/0x3a0 [ 49.784674] [<ffffffff8107c410>] ? async_schedule+0x20/0x20 [ 49.784681] [<ffffffff8106d5d3>] worker_thread+0x133/0x3a0 [ 49.784688] [<ffffffff8106d4a0>] ? manage_workers+0x190/0x190 [ 49.784696] [<ffffffff81073236>] kthread+0xa6/0xb0 [ 49.784707] [<ffffffff815970a4>] kernel_thread_helper+0x4/0x10 [ 49.784715] [<ffffffff81082a7c>] ? finish_task_switch+0x8c/0x110 [ 49.784721] [<ffffffff8158e44b>] ? _raw_spin_unlock_irq+0x3b/0x70 [ 49.784727] [<ffffffff8158e85d>] ? retint_restore_args+0xe/0xe [ 49.784734] [<ffffffff81073190>] ? kthreadd+0x1e0/0x1e0 [ 49.784739] [<ffffffff815970a0>] ? gs_change+0xb/0xb ------------------- This is caused by enqueue_cmd_and_start_io()-> set_performant_mode()-> smp_processor_id() Which if you have debugging enabled calls debug_processor_id() and triggers the warning. The code here is c->Header.ReplyQueue = smp_processor_id() % h->nreply_queues; Since it is not critical that the code complete on the same processor, but the cpu is a hint used in generating the ReplyQueue and will still work if the cpu migrates or is preempted, it is safe to use the raw_smp_processor_id() to surpress the false positve warning. Signed-off-by:John Kacur <jkacur@redhat.com> Acked-by:
Stephen Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
-
Or Gerlitz authored
To run discovery over iSER we need to advertize the CAP_TEXT_NEGO capability towards user space. Also need to make sure the login RX buffer is posted when SendTargets TEXT PDUs are sent. For that end, we use a setting of the ISCSI_PARAM_DISCOVERY_SESS iscsi param as an indication that this is discovery session. Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Yijing Wang authored
PCI core will initialize device MSI/MSI-X capability in pci_msi_init_pci_dev(). So device driver should use pci_dev->msi_cap/msix_cap to determine whether the device support MSI/MSI-X instead of using pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX). Access to PCIe device config space again will consume more time. Signed-off-by:
Yijing Wang <wangyijing@huawei.com> Acked-by:
lindar_liu <lindar_liu@usish.com> Signed-off-by:
-
Anand Kumar Santhanam authored
Signed-off-by: Anandkumar.Santhanam@pmcs.com Signed-off-by: -
Joe Lawrence authored
If mpt3sas_base_map_resources takes an early error path then its counterpart, mpt3sas_base_free_resources needs to be careful about cleaning up: 1 - _base_mask_interrupts and _base_make_ioc_ready require memory mapped I/O registers, make sure that this is true. 2 - _base_free_irq iterates over the adapter's reply_queue_list, so move this list head initialization out of _base_enable_msix to _scsih_probe so this will always be safe. 3 - check that the controller PCI device and its BARs have been enabled before disabling them. Signed-off-by:Joe Lawrence <joe.lawrence@stratus.com> Acked-by:
-
Joe Lawrence authored
If mpt2sas_base_map_resources takes an early error path then its counterpart, mpt2sas_base_free_resources needs to be careful about cleaning up: 1 - _base_mask_interrupts and _base_make_ioc_ready require memory mapped I/O registers, make sure that this is true. 2 - _base_free_irq iterates over the adapter's reply_queue_list, so move this list head initialization out of _base_enable_msix to _scsih_probe so this will always be safe. 3 - check that the controller PCI device and its BARs have been enabled before disabling them. Signed-off-by: -
Ewan D. Milne authored
Generate a uevent when the following Unit Attention ASC/ASCQ codes are received: 2A/01 MODE PARAMETERS CHANGED 2A/09 CAPACITY DATA HAS CHANGED 38/07 THIN PROVISIONING SOFT THRESHOLD REACHED 3F/03 INQUIRY DATA HAS CHANGED 3F/0E REPORTED LUNS DATA HAS CHANGED Log kernel messages when the following Unit Attention ASC/ASCQ codes are received that are not as specific as those above: 2A/xx PARAMETERS CHANGED 3F/xx TARGET OPERATING CONDITIONS HAVE CHANGED Added logic to set expecting_lun_change for other LUNs on the target after REPORTED LUNS DATA HAS CHANGED is received, so that duplicate uevents are not generated, and clear expecting_lun_change when a REPORT LUNS command completes, in accordance with the SPC-3 specification regarding reporting of the 3F 0E ASC/ASCQ UA. [jejb: remove SPC3 test in scsi_report_lun_change and some docbook fixes and unused variable fix, both reported by Fengguang Wu] Signed-off-by:Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
wenxiong@linux.vnet.ibm.com authored
Add the appropriate definitions and table entries for new adapter support. Signed-off-by:
Wen Xiong <wenxiong@linux.vnet.ibm.com> Signed-off-by:
-
Tomas Henzl authored
Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
-
Tomas Henzl authored
When the driver calls scsi_done and after that frees it's internal preallocated memory it can happen that a new job is enqueud before the memory is freed. The allocation fails and the message "cmd_alloc returned NULL" is shown. Patch below fixes it by moving cmd->scsi_done after cmd_free. Signed-off-by:
-
Xinghai Yu authored
It seems the "phy_index++;" have been placed in wrong place, without it the while circle up will do a infinite loop. Signed-off-by:
Xinghai Yu <yuxinghai@cn.fujitsu.com> Acked-by:
Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by:
-
Wolfram Sang authored
devm_ioremap_resource does sanity checks on the given resource. No need to duplicate this in the driver. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
Santosh Y <santoshsy@gmail.com> Signed-off-by:
-
Wei Yongjun authored
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Akinobu Mita authored
scsi_remove_host() sends SYNCHRONIZE CACHE commands for write cache enabled scsi disk devices. So stopping controller working shouldn't be done before scsi_remove_host(). Signed-off-by:
Akinobu Mita <mita@fixstars.com> Signed-off-by:
-
Akinobu Mita authored
When removing the UFS driver, disable_irq() is called and the IRQ is not enabled again. Unfortunately, the IRQ is requested with IRQF_SHARED and it can be shared among several devices. So disabling the IRQ in this way is just breaking other devices which are sharing the IRQ. Signed-off-by:
-
Akinobu Mita authored
Before commit 2953f850 ("[SCSI] ufs: use devres functions for ufshcd"), UFSHCI register was ioremapped by each glue-driver (ufshcd-pltfrm and ufshcd-pci) during probing and it was iounmapped by core-driver during removing driver. The commit converted ufshcd-pltfrm to use devres functions, but it didn't convert ufshcd-pci. Therefore, the change causes ufshcd-pci driver not to iounmap UFSHCI register region during removing driver. This fixes it by converting ufshcd-pci to use devres functions. Signed-off-by:
-
Sujit Reddy Thumma authored
Add runtime PM helpers to suspend/resume UFS controller at runtime. Enable runtime PM by default for pci and platform drivers as the initialized hardware can suspend if it is not used after bootup. Signed-off-by:
Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by:
-
Sujit Reddy Thumma authored
Background operations in the UFS device can be disabled by the host to reduce the response latency of transfer requests. Add support for enabling/disabling the background operations during runtime suspend/resume of the device. If the device is in critical need of BKOPS it will raise an URGENT_BKOPS exception which should be handled by the host to make sure the device performs as expected. During bootup, the BKOPS is enabled in the device by default. The disable of BKOPS is supported only when the driver supports runtime suspend/resume operations as the runtime PM framework provides a way to determine the device idleness and hence BKOPS can be managed effectively. During runtime resume the BKOPS is disabled to reduce latency and during runtime suspend the BKOPS is enabled to allow device to carry out idle time BKOPS. In some cases where the BKOPS is disabled during runtime resume and due to continuous data transfers the runtime suspend is not triggered, the BKOPS is enabled when the device raises a level-2 exception (outstanding operations - performance impact). Signed-off-by:
-
Dolev Raviv authored
Allow UFS device to complete its initialization and accept SCSI commands by setting fDeviceInit flag. The device may take time for this operation and hence the host should poll until fDeviceInit flag is toggled to zero. This step is mandated by UFS device specification for device initialization completion. Signed-off-by:
Dolev Raviv <draviv@codeaurora.org> Signed-off-by:
-
Sujit Reddy Thumma authored
As part of device initialization sequence, sending NOP OUT UPIU and waiting for NOP IN UPIU response is mandatory. This confirms that the device UFS Transport (UTP) layer is functional and the host can configure the device with further commands. Add support for sending NOP OUT UPIU to check the device connection path and test whether the UTP layer on the device side is functional during initialization. A tag is acquired from the SCSI tag map space in order to send the device management command. When the tag is acquired by internal command the scsi command is rejected with host busy flag in order to requeue the request. To avoid frequent collisions between internal commands and scsi commands the device management command tag is allocated in the opposite direction w.r.t block layer tag allocation. Signed-off-by:
-
- 23 Aug, 2013 8 commits
-
-
Adheer Chandravanshi authored
Signed-off-by:
Adheer Chandravanshi <adheer.chandravanshi@qlogic.com> Signed-off-by:
-
Adheer Chandravanshi authored
Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Adheer Chandravanshi authored
Signed-off-by:
-
Adheer Chandravanshi authored
Signed-off-by:
-
Adheer Chandravanshi authored
Flash target index 0 and 1 are reserved for boot target entries created with BIOS utility. Signed-off-by:
-
Adheer Chandravanshi authored
Signed-off-by:
-
Adheer Chandravanshi authored
Signed-off-by:
-
