- 02 Jun, 2010 40 commits
-
-
Juuso Oikarinen authored
The 5GHz bands were scanned without the proper IE's in place, preventing proper 5GHz scanning. This patches fixes the problem by storing a pointer to the scan request (with the IE's) for all iterations of scan. Signed-off-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Juuso Oikarinen authored
A fixed 1 mbps rate was used for the PSM entry/exit null-func frames. Fix this by using the basic rates instead. Signed-off-by:
-
Luciano Coelho authored
The core wl1271 module can also be used with SDIO, so it should not depend on SPI_MASTER. Signed-off-by:
-
Juuso Oikarinen authored
The mac80211 changes to idle almost immediately after transmitting some frames, such as deauth etc. When going to idle, the wl1271 is disconnected, which causes TX frames already on buffers, but not yet transmitted, to be deleted. To make sure deauth frames reach the air, allow the TX buffers to flush before proceeding to idle. Signed-off-by:
Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
As there is more and more stuff triggered by going in and out of idle, create a separate function for handling that. Signed-off-by:
-
Juuso Oikarinen authored
The wl1271 uses a session counter in CMD_JOIN and TX frame descriptors. This counter is used to determine which frames to drop when the CMD_JOIN is executed. The driver executes CMD_JOIN multiple times upon association and sometimes disassociation, and we don't want any frames to get lost. Fix this by incrementing the session counter only when leaving idle (not every CMD_JOIN as before.) Also, remove the TX flush flag from the CMD_JOIN options. Signed-off-by:
-
Dan Carpenter authored
We dereference "wmi" on the line before and also when we initialize "ah". This check has always been after a dereference since the first commit a couple months ago. Looking through the code, it looks like "wmi" can't actually be null here so I just removed the check. Signed-off-by:
Dan Carpenter <error27@gmail.com> Acked-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Julia Lawall authored
Use memdup_user when user data is immediately copied into the allocated region. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; position p; identifier l1,l2; @@ - to = \(kmalloc@p\|kzalloc@p\)(size,flag); + to = memdup_user(from,size); if ( - to==NULL + IS_ERR(to) || ...) { <+... when != goto l1; - -ENOMEM + PTR_ERR(to) ...+> } - if (copy_from_user(to, from, size) != 0) { - <+... when != goto l2; - -EFAULT - ...+> - } // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
The rx status length should also be taken into account while validating the length of a received frame. Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Skip the rx status portion in skb->data before accessing ieee80211 frame header. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
ath9k_rx_skb_preprocess() needs only ieee80211 frame header, pass only frame headers instead of skb to that function. Also remove ineffective frame dump in ath9k_process_rate(). Signed-off-by:
-
Sujith authored
A bunch of data structures are present in the common module, which are internal to ath9k. Move them to ath9k.h Signed-off-by:
-
Sujith authored
This patch relocates RX processing code from the common module to ath9k. This reduces the size of the common module which is also used by ath9k_htc. Signed-off-by:
-
Tobias Klauser authored
The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Acked-by:
Reinette Chatre <reinette.chatre@intel.com> Acked-by:
-
Luis R. Rodriguez authored
To enable it we now disable and re-enable the PHY chips after TX IQ calibration. Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
Johannes Berg authored
When sending action frames, we want to verify that we do that on the correct channel. However, checking the channel type in addition can get in the way, since the channel type could change on the fly during an association, and it's not useful to have the channel type anyway since it has no effect on the transmission. Therefore, make it optional to specify so that if wanted, it can still be checked, but is not required. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Bruno Randolf authored
Since we have sysfs to manually set the ANI levels, we should print errors to the kernel log if the values are out of bounds. Signed-off-by:
Bruno Randolf <br1@einfach.org> Signed-off-by:
-
Bruno Randolf authored
Calculate 'listen' time also when automatic ANI is off, since this and the "busy" time is useful information also in manual mode. Signed-off-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
-
Bruno Randolf authored
/sys/class/ieee80211/phy0/device/ani/ani_mode /sys/class/ieee80211/phy0/device/ani/noise_immunity_level /sys/class/ieee80211/phy0/device/ani/spur_level /sys/class/ieee80211/phy0/device/ani/firstep_level /sys/class/ieee80211/phy0/device/ani/ofdm_weak_signal_detection /sys/class/ieee80211/phy0/device/ani/cck_weak_signal_detection /sys/class/ieee80211/phy0/device/ani/noise_immunity_level_max /sys/class/ieee80211/phy0/device/ani/spur_level_max /sys/class/ieee80211/phy0/device/ani/firstep_level_max sysfs has a lot of symlinks, so you can find the files also in other locations, like (by PCI ID) /sys/devices/pci0000:00/0000:00:11.0/ani and others. Signed-off-by:
-
Bruno Randolf authored
It's our "private driver data"... It's used more often and hw is the mac80211 part. This makes more sense with the next (sysfs) patch. Signed-off-by:
-
Bruno Randolf authored
The old code logically did not make sense and seems to have been confused by the fact that we could have newer EEPROMs on older hardware. In any case the spur mitigation filter was set if the srev was >= AR5K_SREV_AR5424. Spur info is available only from EEPROM versions bigger than 5.3 but but the EEPOM routines will use static values for older versions, so that should be o.k. Signed-off-by:
-
Bruno Randolf authored
Now that we have ftrace, it is not needed any more. Signed-off-by:
-
Bruno Randolf authored
Since NF calibration interferes with TX and RX and also has been the cause of other problems (when it's run concurrently with ath5k_reset) we want to run it less often - every 60 seconds for now. Signed-off-by:
-
Bruno Randolf authored
As far as we know, only NF calibration interferes with RX/TX so we can leave the queues enabled for the other calibrations. BTW: Stopping the queues is not enough for avoiding transmissions, since there might be packets in the queue + beacons are also sent regularly! But i leave it like this until we have a better solution (stopping TX DMA?). Signed-off-by:
-
Bruno Randolf authored
Seperate noise floor calibration from other PHY calibration and move it to the tasklet. This is the first step to more separation of different calibrations. Also move out ath5k_hw_request_rfgain_probe(ah) so we have one clean function for I/Q calibration on 5111x parts. Signed-off-by:
-
Bruno Randolf authored
Initialize calibration timers on reset, since otherwise they might be in the future and the calibration tasklet might not be scheduled for a long time. Signed-off-by:
-
Jussi Kivilinna authored
Buffer size for get_association_info was limited to WEXT event size. Since association info no longer is sent through WEXT, this limit is not needed. Code also did not check if data get truncated, memory outside buffer might be addressed. Fix all these. Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Rx should not be disabed/disabled when hw supports auto sleeping. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Add missing code to handle nullfunc frame completion in ath_tx_edma_tasklet(). Signed-off-by:
-
Walter Goldens authored
Signed-off-by:
Walter Goldens <goldenstranger@yahoo.com> Signed-off-by:
-
Helmut Schaa authored
Don't refuse HT20 channels on devices that don't support HT40. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Use BSS_CHANGED_HT to handle HT parameter changes. The rate information on the target has to be updated to handle changes in HT configuration. Signed-off-by:
-
Sujith authored
This patch removes a large chunk of code dealing with rate management within the driver and simplifying things by removing the hacky method of calculating HT changes. A subsequent patch would fix this by just using BSS_CHANGED_HT from mac80211. Signed-off-by:
-
Sujith authored
Update from internal systems engineering team. Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
-
Julia Lawall authored
Use kmemdup when some other buffer is immediately copied into the allocated region. A simplified version of the semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression from,to,size,flag; statement S; @@ - to = \(kmalloc\|kzalloc\)(size,flag); + to = kmemdup(from,size,flag); if (to==NULL || ...) S - memcpy(to, from, size); // </smpl> Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
