An error occurred fetching the project authors.
- 21 Jul, 2020 3 commits
-
-
Patrick Delaunay authored
Move spi4_pins_a nodes from pinctrl_z to pinctrl as the associated pins are not in BANK Z. Fixes: 498a7014 ("ARM: dts: stm32: Add missing pinctrl entries for STM32MP15") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Erwan Le Ray authored
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins configurations in stm32mp15-pinctrl. - usart2_pins_c pins are connected to Bluetooth chip on dk2 board. - usart3_pins_b pins are connected to GPIO expansion connector on evx board. - usart3_pins_c pins are connected to GPIO expansion connector on dkx board. - uart7_pins_c pins are connected to Arduino Uno connector on dkx board. Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Patrick Delaunay authored
Use tabs where possible and remove multiple blanks lines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 15 Jun, 2020 3 commits
-
-
Erwan Le Ray authored
Fix uart7_pins_a comments to indicate UART7 pins instead of UART4 pins. Fixes: bf4b5f37 ("ARM: dts: stm32: Add missing pinctrl definitions for STM32MP157") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Erwan Le Ray authored
Fix usart and uart nodes ordering. Several usart nodes didn't respect expecting ordering. Fixes: 077e0638 ("ARM: dts: stm32: Add alternate pinmux for USART2 pins on stm32mp15") Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Erwan Le Ray authored
Sleep pin configuration is refined for low power modes: - "sleep" (no wakeup & console suspend enabled): put pins in analog state to optimize power - "idle" (wakeup capability): keep Rx pin in alternate function Signed-off-by: Bich Hemon <bich.hemon@st.com> Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 14 May, 2020 1 commit
-
-
Manivannan Sadhasivam authored
These pinctrl definitions will be used by Stinger96/IoTBox boards from Shiratech. Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 07 May, 2020 5 commits
-
-
Marek Vasut authored
Add another mux option for SPI2 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for ADC pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for FDCAN2 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for FDCAN1 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for I2C2 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 29 Apr, 2020 5 commits
-
-
Marek Vasut authored
Add new mux option for SAI2 pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add new mux option for LTDC pins, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add mux option for USART2 pins, this is used on AV96 board. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for SDMMC1_D123DIR direction pins, SDMMC2 pins 4..7, and SDMMC3 pins PD5_SDMMC3_D2 and PD0_SDMMC3_CMD, this is used on AV96 board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add another mux option for DWMAC RGMII, this is used on AV96 board. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 20 Apr, 2020 3 commits
-
-
Ahmad Fatoum authored
The Linux Automation MC-1 is a SBC built around the Octavo Systems OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and a PMIC. The board has eMMC and a SD slot for storage and GbE for both connectivity and power. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Ahmad Fatoum authored
While all sleep pinctrl group labels now follow a fixed naming scheme, node _names_ for these groups don't: - Some use ${dev}-[0-9], where the suffix is the normal group suffix + 1 - Some use ${dev}-sleep-[0-9], where suffix is the normal group suffix - The <dc node uses ${dev}-[a-z]-[0-9], where the letter matches the phandle and the number suffix is the normal group's suffix + 1 For uniformity, standardize on using ${dev}-[0-9]+ for all normal pinctrl groups and ${dev}-sleep-[0-9]+ for all sleep pinctrl groups. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Ahmad Fatoum authored
Some labels follow the *_sleep_pins_* naming scheme, but some also use *_pins_sleep_*. Because most labels use the former and for uniformity with variants like sdmmc1_b4_pins_a and sdmmc1_dir_pins_a, adopt the *_sleep_pins_* scheme throughout. Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 10 Feb, 2020 5 commits
-
-
Amelie Delaunay authored
Add pinctrl definition for USB High-Speed OTG ID pin and USB Full-Speed OTG DP and DM lines that can be used on stm32mp15. Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add pinmux for UART8. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add pinmux for USART3. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add pinmux entry for SAI2A with alternative pin configuration. This is useful in combination with sai2b_pins_b e.g. for codecs like SGTL5000. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Marek Vasut authored
Add pinmux entry for ethernet0 RMII . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Patrice Chotard <patrice.chotard@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 09 Dec, 2019 9 commits
-
-
Christophe Roullier authored
ETH_MDIO slew-rate should be set to "0" instead of "2". Signed-off-by: Christophe Roullier <christophe.roullier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Alexandre Torgue authored
In order to cover the STM32MP15 SOCs family this commit updates pinctrl file names (group definition and packages files). This family includes: STM32MP151, STM32MP153 and STM32MP157. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Alexandre Torgue authored
This commit modifies stm32mp157 pinctrl files to better manage STM32MP15xx SOCs diversity. Pin controller and gpio controller are moved to common SOC dtsi file. Only pin groups remain in the main pinctrl dtsi file. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Fabrice Gasnier authored
Define adc1_in6 pin used on stm32mp157c eval board. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Yann Gautier authored
On STM32MP1 EVAL and DISCOVERY boards, the SDMMC3 internal peripheral can be used through the GPIO extension connector. The sdmmc3 node is then added in the boards DT files, and the required pins are also added. The node status is disabled as there is no device connected by default. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Yann Gautier <yann.gautier@st.com>
-
Yann Gautier authored
On STM32MP157C-ED1, the eMMC is connected on instance 2 of SDMMC peripheral. The sdmmc2 node is then added in the board DT file, as well as the pins nodes in the pinctrl file. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Yann Gautier authored
Relax sdmmc1 pins slew-rate to minimize peak currents. Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Signed-off-by: Yann Gautier <yann.gautier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Fabrice Gasnier authored
Add all PWM pinctrl definitions that can be used on stm32mp157a-dk1 board. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Fabrice Gasnier authored
Add PWM pinctrl definitions used in low-power (sleep) mode on stm32mp157c-ev1. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 06 Nov, 2019 1 commit
-
-
Patrice Chotard authored
Relax qspi pins slew-rate to minimize peak currents. Fixes: 84403005 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board") Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 25 Oct, 2019 3 commits
-
-
Patrice Chotard authored
Relax qspi pins slew-rate to minimize peak currents. Fixes: 84403005 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board") Link: https://lore.kernel.org/r/20191025130122.11407-1-alexandre.torgue@st.comSigned-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
-
Fabrice Gasnier authored
Define pins that can be used by digital-to-analog converter on stm32mp157c eval daughter board: - PA4 and PA5 pins are available respectively on JP11 and JP10 Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Fabrice Gasnier authored
Define pins that can be used for ADC on stm32mp157a-dk1 board: - AIN connector has ADC input pins - USB Type-C CC1 & CC2 pins (e.g. in18, in19) Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
- 02 Aug, 2019 2 commits
-
-
Alexandre Torgue authored
This patch removes "ngpios" and "gpio-ranges" information from stm32mp157-pinctrl.dtsi file as it is now filled in stm32mp157 pinctrl package files. Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-
Erwan Le Ray authored
Fix compilations warnings detected by -Wall W=1 compilation option: - node has a unit name, but no reg property Signed-off-by: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-