Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.

Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets

=> nobody tracks the packets from the real 1527-max bucket

Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.

Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.

Fixes: 84705fc1 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

What the driver actually reports as 256-511 is in fact 512-1023, and the
TX packets in the 256-511 bucket are not reported. Fix that.

Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ds->ops->port_stp_state_set() is, like most DSA methods, optional, and
if absent, the port is supposed to remain in the forwarding state (as
standalone). Such is the case with the mv88e6060 driver, which does not
offload the bridge layer. DSA warns that the STP state can't be changed
to FORWARDING as part of dsa_port_enable_rt(), when in fact it should not.

The error message is also not up to modern standards, so take the
opportunity to make it more descriptive.

Fixes: fd364541 ("net: dsa: change scope of STP state setter")
Reported-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20220816201445.1809483-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If an error occurs in dsa_devlink_region_create(), then 'priv->regions'
array will be accessed by negative index '-1'.

Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: bf425b82 ("net: dsa: sja1105: expose static config as devlink region")
Link: https://lore.kernel.org/r/20220817003845.389644-1-subkhankulov@ispras.ruSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Westphal says:

====================
netfilter: conntrack and nf_tables bug fixes

The following patchset contains netfilter fixes for net.

Broken since 5.19:
  A few ancient connection tracking helpers assume TCP packets cannot
  exceed 64kb in size, but this isn't the case anymore with 5.19 when
  BIG TCP got merged, from myself.

Regressions since 5.19:
  1. 'conntrack -E expect' won't display anything because nfnetlink failed
     to enable events for expectations, only for normal conntrack events.

  2. partially revert change that added resched calls to a function that can
     be in atomic context.  Both broken and fixed up by myself.

Broken for several releases (up to original merge of nf_tables):
  Several fixes for nf_tables control plane, from Pablo.
  This fixes up resource leaks in error paths and adds more sanity
  checks for mutually exclusive attributes/flags.

Kconfig:
  NF_CONNTRACK_PROCFS is very old and doesn't provide all info provided
  via ctnetlink, so it should not default to y. From Geert Uytterhoeven.

Selftests:
  rework nft_flowtable.sh: it frequently indicated failure; the way it
  tried to detect an offload failure did not work reliably.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  testing: selftests: nft_flowtable.sh: rework test to detect offload failure
  testing: selftests: nft_flowtable.sh: use random netns names
  netfilter: conntrack: NF_CONNTRACK_PROCFS should no longer default to y
  netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified
  netfilter: nf_tables: disallow NFT_SET_ELEM_CATCHALL and NFT_SET_ELEM_INTERVAL_END
  netfilter: nf_tables: NFTA_SET_ELEM_KEY_END requires concat and interval flags
  netfilter: nf_tables: validate NFTA_SET_ELEM_OBJREF based on NFT_SET_OBJECT flag
  netfilter: nf_tables: really skip inactive sets when allocating name
  netfilter: nfnetlink: re-enable conntrack expectation events
  netfilter: nf_tables: fix scheduling-while-atomic splat
  netfilter: nf_ct_irc: cap packet search space to 4k
  netfilter: nf_ct_ftp: prefer skb_linearize
  netfilter: nf_ct_h323: cap packet size at 64k
  netfilter: nf_ct_sane: remove pseudo skb linearization
  netfilter: nf_tables: possible module reference underflow in error path
  netfilter: nf_tables: disallow NFTA_SET_ELEM_KEY_END with NFT_SET_ELEM_INTERVAL_END flag
  netfilter: nf_tables: use READ_ONCE and WRITE_ONCE for shared generation id access
====================

Link: https://lore.kernel.org/r/20220817140015.25843-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

bpf_sk_reuseport_detach() calls __rcu_dereference_sk_user_data_with_flags()
to obtain the value of sk->sk_user_data, but that function is only usable
if the RCU read lock is held, and neither that function nor any of its
callers hold it.

Fix this by adding a new helper, __locked_read_sk_user_data_with_flags()
that checks to see if sk->sk_callback_lock() is held and use that here
instead.

Alternatively, making __rcu_dereference_sk_user_data_with_flags() use
rcu_dereference_checked() might suffice.

Without this, the following warning can be occasionally observed:

=============================
WARNING: suspicious RCU usage
6.0.0-rc1-build2+ #563 Not tainted
-----------------------------
include/net/sock.h:592 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
5 locks held by locktest/29873:
 #0: ffff88812734b550 (&sb->s_type->i_mutex_key#9){+.+.}-{3:3}, at: __sock_release+0x77/0x121
 #1: ffff88812f5621b0 (sk_lock-AF_INET){+.+.}-{0:0}, at: tcp_close+0x1c/0x70
 #2: ffff88810312f5c8 (&h->lhash2[i].lock){+.+.}-{2:2}, at: inet_unhash+0x76/0x1c0
 #3: ffffffff83768bb8 (reuseport_lock){+...}-{2:2}, at: reuseport_detach_sock+0x18/0xdd
 #4: ffff88812f562438 (clock-AF_INET){++..}-{2:2}, at: bpf_sk_reuseport_detach+0x24/0xa4

stack backtrace:
CPU: 1 PID: 29873 Comm: locktest Not tainted 6.0.0-rc1-build2+ #563
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0x4c/0x5f
 bpf_sk_reuseport_detach+0x6d/0xa4
 reuseport_detach_sock+0x75/0xdd
 inet_unhash+0xa5/0x1c0
 tcp_set_state+0x169/0x20f
 ? lockdep_sock_is_held+0x3a/0x3a
 ? __lock_release.isra.0+0x13e/0x220
 ? reacquire_held_locks+0x1bb/0x1bb
 ? hlock_class+0x31/0x96
 ? mark_lock+0x9e/0x1af
 __tcp_close+0x50/0x4b6
 tcp_close+0x28/0x70
 inet_release+0x8e/0xa7
 __sock_release+0x95/0x121
 sock_close+0x14/0x17
 __fput+0x20f/0x36a
 task_work_run+0xa3/0xcc
 exit_to_user_mode_prepare+0x9c/0x14d
 syscall_exit_to_user_mode+0x18/0x44
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: cf8c1e96 ("net: refactor bpf_sk_reuseport_detach()")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hawkins Jiawei <yin31149@gmail.com>
Link: https://lore.kernel.org/r/166064248071.3502205.10036394558814861778.stgit@warthog.procyon.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This test fails on current kernel releases because the flotwable path
now calls dst_check from packet path and will then remove the offload.

Test script has two purposes:
1. check that file (random content) can be sent to other netns (and vv)
2. check that the flow is offloaded (rather than handled by classic
   forwarding path).

Since dst_check is in place, 2) fails because the nftables ruleset in
router namespace 1 intentionally blocks traffic under the assumption
that packets are not passed via classic path at all.

Rework this: Instead of blocking traffic, create two named counters, one
for original and one for reverse direction.

The first three test cases are handled by classic forwarding path
(path mtu discovery is disabled and packets exceed MTU).

But all other tests enable PMTUD, so the originator and responder are
expected to lower packet size and flowtable is expected to do the packet
forwarding.

For those tests, check that the packet counters (which are only
incremented for packets that are passed up to classic forward path)
are significantly lower than the file size transferred.

I've tested that the counter-checks fail as expected when the 'flow add'
statement is removed from the ruleset.
Signed-off-by: Florian Westphal <fw@strlen.de>

====================
Intel Wired LAN Driver Updates 2022-08-16)

This series contains updates to i40e driver only.

Przemyslaw fixes issue with checksum offload on VXLAN tunnels.

Alan disables VSI for Tx timeout when all recovery methods have failed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Even though the normal strparser's init function has a return
value we got away with ignoring errors until now, as it only
validates the parameters and we were passing correct parameters.

tls_strp can fail to init on memory allocation errors, which
syzbot duly induced and reported.

Reported-by: syzbot+abd45eb849b05194b1b6@syzkaller.appspotmail.com
Fixes: 84c61fe1 ("tls: rx: do not use the standard strparser")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

"ns1" is a too generic name, use a random suffix to avoid
errors when such a netns exists.  Also allows to run multiple
instances of the script in parallel.
Signed-off-by: Florian Westphal <fw@strlen.de>

NF_CONNTRACK_PROCFS was marked obsolete in commit 54b07dca
("netfilter: provide config option to disable ancient procfs parts") in
v3.3.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Westphal <fw@strlen.de>

In the gnet_stats_add_queue_cpu function, the qstats->qlen statistics
are incorrectly set to qcpu->backlog.

Fixes: 448e163f ("gen_stats: Add gnet_stats_add_queue()")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220815030848.276746-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When a tx_timeout fires, the PF attempts to recover by incrementally
resetting.  First we try a PFR, then CORER and finally a GLOBR.  If the
GLOBR fails, then we keep hitting the tx_timeout and incrementing the
recovery level and issuing dmesgs, which is both annoying to the user
and accomplishes nothing.

If the GLOBR fails, then we're pretty much totally hosed, and there's
not much else we can do to recover, so this makes it such that we just
kill the VSI and stop hitting the tx_timeout in such a case.

Fixes: 41c445ff ("i40e: main driver core")
Signed-off-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.

Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev \
enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect

Without this patch, TX descriptor was using wrong data, due to
l4 header pointing wrong address. NIC would then drop those packets
internally, due to incorrect TX descriptor data, which increased
GLV_TEPC register.

Fixes: b4fb2d33 ("i40e: Add support for MPLS + TSO")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-08-12 (iavf)

This series contains updates to iavf driver only.

Przemyslaw frees memory for admin queues in initialization error paths,
prevents freeing of vf_res which is causing null pointer dereference,
and adjusts calls in error path of reset to avoid iavf_close() which
could cause deadlock.

Ivan Vecera avoids deadlock that can occur when driver if part of
failover.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  iavf: Fix deadlock in initialization
  iavf: Fix reset error handling
  iavf: Fix NULL pointer dereference in iavf_get_link_ksettings
  iavf: Fix adminq error handling
====================

Link: https://lore.kernel.org/r/20220812172309.853230-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When bulk delete command is received in the rtnetlink_rcv_msg function,
if bulk delete is not supported, module_put is not called to release
the reference counting. As a result, module reference count is leaked.

Fixes: a6cec0bc ("net: rtnetlink: add bulk delete support flag")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220815024629.240367-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

dma_map_single() calls fail in moxart_mac_setup_desc_ring() and
moxart_mac_start_xmit() which leads to an incessant output of this:

[   16.043925] moxart-ethernet 92000000.mac eth0: DMA mapping error
[   16.050957] moxart-ethernet 92000000.mac eth0: DMA mapping error
[   16.058229] moxart-ethernet 92000000.mac eth0: DMA mapping error

Passing pdev to DMA is a common approach among net drivers.

Fixes: 6c821bd9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220812171339.2271788-1-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since f3a2181e ("netfilter: nf_tables: Support for sets with
multiple ranged fields"), it possible to combine intervals and
concatenations. Later on, ef516e86 ("netfilter: nf_tables:
reintroduce the NFT_SET_CONCAT flag") provides the NFT_SET_CONCAT flag
for userspace to report that the set stores a concatenation.

Make sure NFT_SET_CONCAT is set on if field_count is specified for
consistency. Otherwise, if NFT_SET_CONCAT is specified with no
field_count, bail out with EINVAL.

Fixes: ef516e86 ("netfilter: nf_tables: reintroduce the NFT_SET_CONCAT flag")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

These flags are mutually exclusive, report EINVAL in this case.

Fixes: aaa31047 ("netfilter: nftables: add catch-all set element support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If the NFT_SET_CONCAT|NFT_SET_INTERVAL flags are set on, then the
netlink attribute NFTA_SET_ELEM_KEY_END must be specified. Otherwise,
NFTA_SET_ELEM_KEY_END should not be present.

For catch-all element, NFTA_SET_ELEM_KEY_END should not be present.
The NFT_SET_ELEM_INTERVAL_END is never used with this set flags
combination.

Fixes: 7b225d0b ("netfilter: nf_tables: add NFTA_SET_ELEM_KEY_END attribute")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Petr Machata says:

====================
mlxsw: Fixes for PTP support

This set fixes several issues in mlxsw PTP code.

- Patch #1 fixes compilation warnings.

- Patch #2 adjusts the order of operation during cleanup, thereby
  closing the window after PTP state was already cleaned in the ASIC
  for the given port, but before the port is removed, when the user
  could still in theory make changes to the configuration.

- Patch #3 protects the PTP configuration with a custom mutex, instead
  of relying on RTNL, which is not held in all access paths.

- Patch #4 forbids enablement of PTP only in RX or only in TX. The
  driver implicitly assumed this would be the case, but neglected to
  sanitize the configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently mlxsw driver configures one global PTP configuration for all
ports. The reason is that the switch behaves like a transparent clock
between CPU port and front-panel ports. When time stamp is enabled in
any port, the hardware is configured to update the correction field. The
fact that the configuration of CPU port affects all the ports, makes the
correction field update to be global for all ports. Otherwise, user will
see odd values in the correction field, as the switch will update the
correction field in the CPU port, but not in all the front-panel ports.

The CPU port is relevant in both RX and TX, so to avoid problematic
configuration, forbid PTP enablement only in one direction, i.e., only in
RX or TX.

Without the change:
$ hwstamp_ctl -i swp1 -r 12 -t 0
current settings:
tx_type 0
rx_filter 0
new settings:
tx_type 0
rx_filter 2
$ echo $?
0

With the change:
$ hwstamp_ctl -i swp1 -r 12 -t 0
current settings:
tx_type 1
rx_filter 2
SIOCSHWTSTAMP failed: Invalid argument

Fixes: 08ef8bc8 ("mlxsw: spectrum_ptp: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the functions mlxsw_sp2_ptp_{configure, deconfigure}_port()
assume that they are called when RTNL is locked and they warn otherwise.

The deconfigure function can be called when port is removed, for example
as part of device reload, then there is no locked RTNL and the function
warns [1].

To avoid such case, do not assume that RTNL protects this code, add a
dedicated mutex instead. The mutex protects 'ptp_state->config' which
stores the existing global configuration in hardware. Use this mutex also
to protect the code which configures the hardware. Then, there will be
only one configuration in any time, which will be updated in 'ptp_state'
and a race will be avoided.

[1]:
RTNL: assertion failed at drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c (1600)
WARNING: CPU: 1 PID: 1583493 at drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c:1600 mlxsw_sp2_ptp_hwtstamp_set+0x2d3/0x300 [mlxsw_spectrum]
[...]
CPU: 1 PID: 1583493 Comm: devlink Not tainted5.19.0-rc8-custom-127022-gb371dffda095 #789
Hardware name: Mellanox Technologies Ltd.MSN3420/VMOD0005, BIOS 5.11 01/06/2019
RIP: 0010:mlxsw_sp2_ptp_hwtstamp_set+0x2d3/0x300[mlxsw_spectrum]
[...]
Call Trace:
 <TASK>
 mlxsw_sp_port_remove+0x7e/0x190 [mlxsw_spectrum]
 mlxsw_sp_fini+0xd1/0x270 [mlxsw_spectrum]
 mlxsw_core_bus_device_unregister+0x55/0x280 [mlxsw_core]
 mlxsw_devlink_core_bus_device_reload_down+0x1c/0x30[mlxsw_core]
 devlink_reload+0x1ee/0x230
 devlink_nl_cmd_reload+0x4de/0x580
 genl_family_rcv_msg_doit+0xdc/0x140
 genl_rcv_msg+0xd7/0x1d0
 netlink_rcv_skb+0x49/0xf0
 genl_rcv+0x1f/0x30
 netlink_unicast+0x22f/0x350
 netlink_sendmsg+0x208/0x440
 __sys_sendto+0xf0/0x140
 __x64_sys_sendto+0x1b/0x20
 do_syscall_64+0x35/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: 08ef8bc8 ("mlxsw: spectrum_ptp: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently as part of removing port, PTP API is called to clear the
existing configuration and set the 'rx_filter' and 'tx_type' to zero.
The clearing is done before unregistering the netdevice, which means that
there is a window of time in which the user can reconfigure PTP in the
port, and this configuration will not be cleared.

Reorder the operations, clear PTP configuration after unregistering the
netdevice.

Fixes: 87486427 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case that 'CONFIG_PTP_1588_CLOCK' is not enabled in the config file,
there are implementations for the functions
mlxsw_{sp,sp2}_ptp_txhdr_construct() as part of 'spectrum_ptp.h'. In this
case, they should be defined as 'static' as they are not supposed to be
used out of this file. Make the functions 'static', otherwise the following
warnings are returned:

"warning: no previous prototype for 'mlxsw_sp_ptp_txhdr_construct'"
"warning: no previous prototype for 'mlxsw_sp2_ptp_txhdr_construct'"

In addition, make the functions 'inline' for case that 'spectrum_ptp.h'
will be included anywhere else and the functions would probably not be
used, so compilation warnings about unused static will be returned.

Fixes: 24157bc6 ("mlxsw: Send PTP packets as data packets to overcome a limitation")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Follows up on:
https://lore.kernel.org/all/20220809170518.164662-1-cascardo@canonical.com/

handle of 0 implies from/to of universe realm which is not very
sensible.

Lets see what this patch will do:
$sudo tc qdisc add dev $DEV root handle 1:0 prio

//lets manufacture a way to insert handle of 0
$sudo tc filter add dev $DEV parent 1:0 protocol ip prio 100 \
route to 0 from 0 classid 1:10 action ok

//gets rejected...
Error: handle of 0 is not valid.
We have an error talking to the kernel, -1

//lets create a legit entry..
sudo tc filter add dev $DEV parent 1:0 protocol ip prio 100 route from 10 \
classid 1:10 action ok

//what did the kernel insert?
$sudo tc filter ls dev $DEV parent 1:0
filter protocol ip pref 100 route chain 0
filter protocol ip pref 100 route chain 0 fh 0x000a8000 flowid 1:10 from 10
	action order 1: gact action pass
	 random type none pass val 0
	 index 1 ref 1 bind 1

//Lets try to replace that legit entry with a handle of 0
$ sudo tc filter replace dev $DEV parent 1:0 protocol ip prio 100 \
handle 0x000a8000 route to 0 from 0 classid 1:10 action drop

Error: Replacing with handle of 0 is invalid.
We have an error talking to the kernel, -1

And last, lets run Cascardo's POC:
$ ./poc
0
0
-22
-22
-22
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The issue happens on specific paths in the function. After both the
object `rt` and `neigh` are grabbed successfully, when `lifetime` is
nonzero but the metric needs change, the function just deletes the
route and set `rt` to NULL. Then, it may try grabbing `rt` and `neigh`
again if above conditions hold. The function simply overwrite `neigh`
if succeeds or returns if fails, without decreasing the reference
count of previous `neigh`. This may result in memory leaks.

Fix it by decrementing the reference count of `neigh` in place.

Fixes: 6b2e04bc ("net: allow user to set metric on default route learned via Router Advertisement")
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

-queue

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-08-11 (ice)

This series contains updates to ice driver only.

Benjamin corrects a misplaced parenthesis for a WARN_ON check.

Michal removes WARN_ON from a check as its recoverable and not
warranting of a call trace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Right now we have a neigh_param PROXY_QLEN which specifies maximum length
of neigh_table->proxy_queue. But in fact, this limitation doesn't work well
because check condition looks like:
tbl->proxy_queue.qlen > NEIGH_VAR(p, PROXY_QLEN)

The problem is that p (struct neigh_parms) is a per-device thing,
but tbl (struct neigh_table) is a system-wide global thing.

It seems reasonable to make proxy_queue limit per-device based.

v2:
	- nothing changed in this patch
v3:
	- rebase to net tree

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@kernel.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: Konstantin Khorenko <khorenko@virtuozzo.com>
Cc: kernel@openvz.org
Cc: devel@openvz.org
Suggested-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Normal processing of ARP request (usually this is Ethernet broadcast
packet) coming to the host is looking like the following:
* the packet comes to arp_process() call and is passed through routing
  procedure
* the request is put into the queue using pneigh_enqueue() if
  corresponding ARP record is not local (common case for container
  records on the host)
* the request is processed by timer (within 80 jiffies by default) and
  ARP reply is sent from the same arp_process() using
  NEIGH_CB(skb)->flags & LOCALLY_ENQUEUED condition (flag is set inside
  pneigh_enqueue())

And here the problem comes. Linux kernel calls pneigh_queue_purge()
which destroys the whole queue of ARP requests on ANY network interface
start/stop event through __neigh_ifdown().

This is actually not a problem within the original world as network
interface start/stop was accessible to the host 'root' only, which
could do more destructive things. But the world is changed and there
are Linux containers available. Here container 'root' has an access
to this API and could be considered as untrusted user in the hosting
(container's) world.

Thus there is an attack vector to other containers on node when
container's root will endlessly start/stop interfaces. We have observed
similar situation on a real production node when docker container was
doing such activity and thus other containers on the node become not
accessible.

The patch proposed doing very simple thing. It drops only packets from
the same namespace in the pneigh_queue_purge() where network interface
state change is detected. This is enough to prevent the problem for the
whole node preserving original semantics of the code.

v2:
	- do del_timer_sync() if queue is empty after pneigh_queue_purge()
v3:
	- rebase to net tree

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@kernel.org>
Cc: Yajun Deng <yajun.deng@linux.dev>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Cc: Konstantin Khorenko <khorenko@virtuozzo.com>
Cc: kernel@openvz.org
Cc: devel@openvz.org
Investigated-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

MHI channel may generates event/interrupt right after enabling.
It may leads to 2 race conditions issues.

1)
Such event may be dropped by qcom_mhi_qrtr_dl_callback() at check:

	if (!qdev || mhi_res->transaction_status)
		return;

Because dev_set_drvdata(&mhi_dev->dev, qdev) may be not performed at
this moment. In this situation qrtr-ns will be unable to enumerate
services in device.
---------------------------------------------------------------

2)
Such event may come at the moment after dev_set_drvdata() and
before qrtr_endpoint_register(). In this case kernel will panic with
accessing wrong pointer at qcom_mhi_qrtr_dl_callback():

	rc = qrtr_endpoint_post(&qdev->ep, mhi_res->buf_addr,
				mhi_res->bytes_xferd);

Because endpoint is not created yet.
--------------------------------------------------------------
So move mhi_prepare_for_transfer_autoqueue after endpoint creation
to fix it.

Fixes: a2e2cc0d ("net: qrtr: Start MHI channels during init")
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Hemant Kumar <quic_hemantk@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Functions ip6_tnl_change, ip6_tnl_update and ip6_tnl0_update do always
return 0, change the type of functions to void.
Signed-off-by: Hongbin Wang <wh_bin@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the port isn't a CPU port nor a user port, 'cpu_dp'
is a null pointer and a crash happened on dereferencing
it in mv88e6060_setup_port():

[    9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014
...
[    9.942216]  mv88e6060_setup from dsa_register_switch+0x814/0xe84
[    9.948616]  dsa_register_switch from mdio_probe+0x2c/0x54
[    9.954433]  mdio_probe from really_probe.part.0+0x98/0x2a0
[    9.960375]  really_probe.part.0 from driver_probe_device+0x30/0x10c
[    9.967029]  driver_probe_device from __device_attach_driver+0xb8/0x13c
[    9.973946]  __device_attach_driver from bus_for_each_drv+0x90/0xe0
[    9.980509]  bus_for_each_drv from __device_attach+0x110/0x184
[    9.986632]  __device_attach from bus_probe_device+0x8c/0x94
[    9.992577]  bus_probe_device from deferred_probe_work_func+0x78/0xa8
[    9.999311]  deferred_probe_work_func from process_one_work+0x290/0x73c
[   10.006292]  process_one_work from worker_thread+0x30/0x4b8
[   10.012155]  worker_thread from kthread+0xd4/0x10c
[   10.017238]  kthread from ret_from_fork+0x14/0x3c

Fixes: 0abfd494 ("net: dsa: use dedicated CPU port")
CC: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220811070939.1717146-1-saproj@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Code reimplements functionality already in `fec_ptp_read()`,
but misses check for FEC_QUIRK_BUG_CAPTURE. Replace with function call.

Fixes: 28b5f058 ("net: fec: ptp: fix convergence issue to support LinuxPTP stack")
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Link: https://lore.kernel.org/r/20220811101348.13755-1-csokas.bence@prolan.huSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix deadlock that occurs when iavf interface is a part of failover
configuration.

1. Mutex crit_lock is taken at the beginning of iavf_watchdog_task()
2. Function iavf_init_config_adapter() is called when adapter
   state is __IAVF_INIT_CONFIG_ADAPTER
3. iavf_init_config_adapter() calls register_netdevice() that emits
   NETDEV_REGISTER event
4. Notifier function failover_event() then calls
   net_failover_slave_register() that calls dev_open()
5. dev_open() calls iavf_open() that tries to take crit_lock in
   end-less loop

Stack trace:
...
[  790.251876]  usleep_range_state+0x5b/0x80
[  790.252547]  iavf_open+0x37/0x1d0 [iavf]
[  790.253139]  __dev_open+0xcd/0x160
[  790.253699]  dev_open+0x47/0x90
[  790.254323]  net_failover_slave_register+0x122/0x220 [net_failover]
[  790.255213]  failover_slave_register.part.7+0xd2/0x180 [failover]
[  790.256050]  failover_event+0x122/0x1ab [failover]
[  790.256821]  notifier_call_chain+0x47/0x70
[  790.257510]  register_netdevice+0x20f/0x550
[  790.258263]  iavf_watchdog_task+0x7c8/0xea0 [iavf]
[  790.259009]  process_one_work+0x1a7/0x360
[  790.259705]  worker_thread+0x30/0x390

To fix the situation we should check the current adapter state after
first unsuccessful mutex_trylock() and return with -EBUSY if it is
__IAVF_INIT_CONFIG_ADAPTER.

Fixes: 226d5285 ("iavf: fix locking of critical sections")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Do not call iavf_close in iavf_reset_task error handling. Doing so can
lead to double call of napi_disable, which can lead to deadlock there.
Removing VF would lead to iavf_remove task being stuck, because it
requires crit_lock, which is held by iavf_close.
Call iavf_disable_vf if reset fail, so that driver will clean up
remaining invalid resources.
During rapid VF resets, HW can fail to setup VF mailbox. Wrong
error handling can lead to iavf_remove being stuck with:
[ 5218.999087] iavf 0000:82:01.0: Failed to init adminq: -53
...
[ 5267.189211] INFO: task repro.sh:11219 blocked for more than 30 seconds.
[ 5267.189520]       Tainted: G S          E     5.18.0-04958-ga54ce370-dirty #1
[ 5267.189764] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 5267.190062] task:repro.sh        state:D stack:    0 pid:11219 ppid:  8162 flags:0x00000000
[ 5267.190347] Call Trace:
[ 5267.190647]  <TASK>
[ 5267.190927]  __schedule+0x460/0x9f0
[ 5267.191264]  schedule+0x44/0xb0
[ 5267.191563]  schedule_preempt_disabled+0x14/0x20
[ 5267.191890]  __mutex_lock.isra.12+0x6e3/0xac0
[ 5267.192237]  ? iavf_remove+0xf9/0x6c0 [iavf]
[ 5267.192565]  iavf_remove+0x12a/0x6c0 [iavf]
[ 5267.192911]  ? _raw_spin_unlock_irqrestore+0x1e/0x40
[ 5267.193285]  pci_device_remove+0x36/0xb0
[ 5267.193619]  device_release_driver_internal+0xc1/0x150
[ 5267.193974]  pci_stop_bus_device+0x69/0x90
[ 5267.194361]  pci_stop_and_remove_bus_device+0xe/0x20
[ 5267.194735]  pci_iov_remove_virtfn+0xba/0x120
[ 5267.195130]  sriov_disable+0x2f/0xe0
[ 5267.195506]  ice_free_vfs+0x7d/0x2f0 [ice]
[ 5267.196056]  ? pci_get_device+0x4f/0x70
[ 5267.196496]  ice_sriov_configure+0x78/0x1a0 [ice]
[ 5267.196995]  sriov_numvfs_store+0xfe/0x140
[ 5267.197466]  kernfs_fop_write_iter+0x12e/0x1c0
[ 5267.197918]  new_sync_write+0x10c/0x190
[ 5267.198404]  vfs_write+0x24e/0x2d0
[ 5267.198886]  ksys_write+0x5c/0xd0
[ 5267.199367]  do_syscall_64+0x3a/0x80
[ 5267.199827]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 5267.200317] RIP: 0033:0x7f5b381205c8
[ 5267.200814] RSP: 002b:00007fff8c7e8c78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 5267.201981] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007f5b381205c8
[ 5267.202620] RDX: 0000000000000002 RSI: 00005569420ee900 RDI: 0000000000000001
[ 5267.203426] RBP: 00005569420ee900 R08: 000000000000000a R09: 00007f5b38180820
[ 5267.204327] R10: 000000000000000a R11: 0000000000000246 R12: 00007f5b383c06e0
[ 5267.205193] R13: 0000000000000002 R14: 00007f5b383bb880 R15: 0000000000000002
[ 5267.206041]  </TASK>
[ 5267.206970] Kernel panic - not syncing: hung_task: blocked tasks
[ 5267.207809] CPU: 48 PID: 551 Comm: khungtaskd Kdump: loaded Tainted: G S          E     5.18.0-04958-ga54ce370-dirty #1
[ 5267.208726] Hardware name: Dell Inc. PowerEdge R730/0WCJNT, BIOS 2.11.0 11/02/2019
[ 5267.209623] Call Trace:
[ 5267.210569]  <TASK>
[ 5267.211480]  dump_stack_lvl+0x33/0x42
[ 5267.212472]  panic+0x107/0x294
[ 5267.213467]  watchdog.cold.8+0xc/0xbb
[ 5267.214413]  ? proc_dohung_task_timeout_secs+0x30/0x30
[ 5267.215511]  kthread+0xf4/0x120
[ 5267.216459]  ? kthread_complete_and_exit+0x20/0x20
[ 5267.217505]  ret_from_fork+0x22/0x30
[ 5267.218459]  </TASK>

Fixes: f0db7892 ("i40evf: use netdev variable in reset task")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix possible NULL pointer dereference, due to freeing of adapter->vf_res
in iavf_init_get_resources. Previous commit introduced a regression,
where receiving IAVF_ERR_ADMIN_QUEUE_NO_WORK from iavf_get_vf_config
would free adapter->vf_res. However, netdev is still registered, so
ethtool_ops can be called. Calling iavf_get_link_ksettings with no vf_res,
will result with:
[ 9385.242676] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 9385.242683] #PF: supervisor read access in kernel mode
[ 9385.242686] #PF: error_code(0x0000) - not-present page
[ 9385.242690] PGD 0 P4D 0
[ 9385.242696] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI
[ 9385.242701] CPU: 6 PID: 3217 Comm: pmdalinux Kdump: loaded Tainted: G S          E     5.18.0-04958-ga54ce370-dirty #1
[ 9385.242708] Hardware name: Dell Inc. PowerEdge R730/0WCJNT, BIOS 2.11.0 11/02/2019
[ 9385.242710] RIP: 0010:iavf_get_link_ksettings+0x29/0xd0 [iavf]
[ 9385.242745] Code: 00 0f 1f 44 00 00 b8 01 ef ff ff 48 c7 46 30 00 00 00 00 48 c7 46 38 00 00 00 00 c6 46 0b 00 66 89 46 08 48 8b 87 68 0e 00 00 <f6> 40 08 80 75 50 8b 87 5c 0e 00 00 83 f8 08 74 7a 76 1d 83 f8 20
[ 9385.242749] RSP: 0018:ffffc0560ec7fbd0 EFLAGS: 00010246
[ 9385.242755] RAX: 0000000000000000 RBX: ffffc0560ec7fc08 RCX: 0000000000000000
[ 9385.242759] RDX: ffffffffc0ad4550 RSI: ffffc0560ec7fc08 RDI: ffffa0fc66674000
[ 9385.242762] RBP: 00007ffd1fb2bf50 R08: b6a2d54b892363ee R09: ffffa101dc14fb00
[ 9385.242765] R10: 0000000000000000 R11: 0000000000000004 R12: ffffa0fc66674000
[ 9385.242768] R13: 0000000000000000 R14: ffffa0fc66674000 R15: 00000000ffffffa1
[ 9385.242771] FS:  00007f93711a2980(0000) GS:ffffa0fad72c0000(0000) knlGS:0000000000000000
[ 9385.242775] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 9385.242778] CR2: 0000000000000008 CR3: 0000000a8e61c003 CR4: 00000000003706e0
[ 9385.242781] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 9385.242784] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 9385.242787] Call Trace:
[ 9385.242791]  <TASK>
[ 9385.242793]  ethtool_get_settings+0x71/0x1a0
[ 9385.242814]  __dev_ethtool+0x426/0x2f40
[ 9385.242823]  ? slab_post_alloc_hook+0x4f/0x280
[ 9385.242836]  ? kmem_cache_alloc_trace+0x15d/0x2f0
[ 9385.242841]  ? dev_ethtool+0x59/0x170
[ 9385.242848]  dev_ethtool+0xa7/0x170
[ 9385.242856]  dev_ioctl+0xc3/0x520
[ 9385.242866]  sock_do_ioctl+0xa0/0xe0
[ 9385.242877]  sock_ioctl+0x22f/0x320
[ 9385.242885]  __x64_sys_ioctl+0x84/0xc0
[ 9385.242896]  do_syscall_64+0x3a/0x80
[ 9385.242904]  entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 9385.242918] RIP: 0033:0x7f93702396db
[ 9385.242923] Code: 73 01 c3 48 8b 0d ad 57 38 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 7d 57 38 00 f7 d8 64 89 01 48
[ 9385.242927] RSP: 002b:00007ffd1fb2bf18 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 9385.242932] RAX: ffffffffffffffda RBX: 000055671b1d2fe0 RCX: 00007f93702396db
[ 9385.242935] RDX: 00007ffd1fb2bf20 RSI: 0000000000008946 RDI: 0000000000000007
[ 9385.242937] RBP: 00007ffd1fb2bf20 R08: 0000000000000003 R09: 0030763066307330
[ 9385.242940] R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffd1fb2bf80
[ 9385.242942] R13: 0000000000000007 R14: 0000556719f6de90 R15: 00007ffd1fb2c1b0
[ 9385.242948]  </TASK>
[ 9385.242949] Modules linked in: iavf(E) xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nft_compat nf_nat_tftp nft_objref nf_conntrack_tftp bridge stp llc nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables rfkill nfnetlink vfat fat irdma ib_uverbs ib_core intel_rapl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm iTCO_wdt iTCO_vendor_support ice irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel rapl i40e pcspkr intel_cstate joydev mei_me intel_uncore mxm_wmi mei ipmi_ssif lpc_ich ipmi_si acpi_power_meter xfs libcrc32c mgag200 i2c_algo_bit drm_shmem_helper drm_kms_helper sd_mod t10_pi crc64_rocksoft crc64 syscopyarea sg sysfillrect sysimgblt fb_sys_fops drm ixgbe ahci libahci libata crc32c_intel mdio dca wmi dm_mirror dm_region_hash dm_log dm_mod ipmi_devintf ipmi_msghandler fuse
[ 9385.243065]  [last unloaded: iavf]

Dereference happens in if (ADV_LINK_SUPPORT(adapter)) statement

Fixes: 209f2f9c ("iavf: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2 negotiation")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

iavf_alloc_asq_bufs/iavf_alloc_arq_bufs allocates with dma_alloc_coherent
memory for VF mailbox.
Free DMA regions for both ASQ and ARQ in case error happens during
configuration of ASQ/ARQ registers.
Without this change it is possible to see when unloading interface:
74626.583369: dma_debug_device_change: device driver has pending DMA allocations while released from device [count=32]
One of leaked entries details: [device address=0x0000000b27ff9000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]

Fixes: d358aa9a ("i40evf: init code and hardware support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

If the NFTA_SET_ELEM_OBJREF netlink attribute is present and
NFT_SET_OBJECT flag is set on, report EINVAL.

Move existing sanity check earlier to validate that NFT_SET_OBJECT
requires NFTA_SET_ELEM_OBJREF.

Fixes: 8aeff920 ("netfilter: nf_tables: add stateful object reference to set elements")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>