- 23 Nov, 2018 40 commits
-
-
Frieder Schrempf authored
[ Upstream commit 7b900ead ] We need to make sure, that the carrier check polling is disabled while suspending. Otherwise we can end up with usbnet_read_cmd() being issued when only usbnet_read_cmd_nopm() is allowed. If this happens, read operations lock up. Fixes: d69d1694 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation") Signed-off-by:
Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by:
Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Howells authored
[ Upstream commit c7e86acf ] If the network becomes (partially) unavailable, say by disabling IPv6, the background ACK transmission routine can get itself into a tizzy by proposing immediate ACK retransmission. Since we're in the call event processor, that happens immediately without returning to the workqueue manager. The condition should clear after a while when either the network comes back or the call times out. Fix this by: (1) When re-proposing an ACK on failed Tx, don't schedule it immediately. This will allow a certain amount of time to elapse before we try again. (2) Enforce a return to the workqueue manager after a certain number of iterations of the call processing loop. (3) Add a backoff delay that increases the delay on deferred ACKs by a jiffy per failed transmission to a limit of HZ. The backoff delay is cleared on a successful return from kernel_sendmsg(). (4) Cancel calls immediately if the opening sendmsg fails. The layer above can arrange retransmission or rotate to another server. Fixes: 248f219c ("rxrpc: Rewrite the data and ack handling code") Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Stefan Wahren authored
[ Upstream commit 85b18b02 ] The commit f77f0aee ("net: use core MTU range checking in USB NIC drivers") introduce a common MTU handling for usbnet. But it's missing the necessary changes for smsc95xx. So set the MTU range accordingly. This patch has been tested on a Raspberry Pi 3. Fixes: f77f0aee ("net: use core MTU range checking in USB NIC drivers") Signed-off-by:
Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by:
-
Shalom Toledo authored
[ Upstream commit 96801552 ] The CPU policer used to police packets being trapped via a local route (IP2ME) was incorrectly configured to police based on bytes per second instead of packets per second. Change the policer to police based on packets per second and avoid packet loss under certain circumstances. Fixes: 9148e7cf ("mlxsw: spectrum: Add policers for trap groups") Signed-off-by:
Shalom Toledo <shalomt@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit e1e46479 ] Different from processing the addstrm_out request, The receiver handles an addstrm_in request by sending back an addstrm_out request to the sender who will increase its stream's in and incnt later. Now stream->incnt has been increased since it sent out the addstrm_in request in sctp_send_add_streams(), with the wrong stream->incnt will even cause crash when copying stream info from the old stream's in to the new one's in sctp_process_strreset_addstrm_out(). This patch is to fix it by simply removing the stream->incnt change from sctp_send_add_streams(). Fixes: 242bd2d5 ("sctp: implement sender-side procedures for Add Incoming/Outgoing Streams Request Parameter") Reported-by:
Jianwen Ji <jiji@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Martin Schiller authored
[ Upstream commit df5a8ec6 ] Up until commit 7e5fbd1e ("net: mdio-gpio: Convert to use gpiod functions where possible"), the _cansleep variants of the gpio_ API was used. After that commit and the change to gpiod_ API, the _cansleep() was dropped. This then results in WARN_ON() when used with GPIO devices which do sleep. Add back the _cansleep() to avoid this. Fixes: 7e5fbd1e ("net: mdio-gpio: Convert to use gpiod functions where possible") Signed-off-by:
Martin Schiller <ms@dev.tdt.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit fd82d61b ] As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED and SCTP_STREAM_CHANGE_FAILED should be used instead of SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED. To keep the compatibility, fix it by adding two macros. Fixes: b444153f ("sctp: add support for generating add stream change event notification") Reported-by:
-
Tristram Ha authored
[ Upstream commit 284fb78e ] Initialize mutex before use. Avoid kernel complaint when CONFIG_DEBUG_LOCK_ALLOC is enabled. Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477") Signed-off-by:
Tristram Ha <Tristram.Ha@microchip.com> Reviewed-by:
Pavel Machek <pavel@ucw.cz> Reviewed-by:
-
Subash Abhinov Kasiviswanathan authored
[ Upstream commit d02854dc ] A null dereference was observed when a sysctl was being set from userspace and rmnet was stuck trying to complete some actions in the NETDEV_REGISTER callback. This is because the real_dev is set only after the device registration handler completes. sysctl call stack - <6> Unable to handle kernel NULL pointer dereference at virtual address 00000108 <2> pc : rmnet_vnd_get_iflink+0x1c/0x28 <2> lr : dev_get_iflink+0x2c/0x40 <2> rmnet_vnd_get_iflink+0x1c/0x28 <2> inet6_fill_ifinfo+0x15c/0x234 <2> inet6_ifinfo_notify+0x68/0xd4 <2> ndisc_ifinfo_sysctl_change+0x1b8/0x234 <2> proc_sys_call_handler+0xac/0x100 <2> proc_sys_write+0x3c/0x4c <2> __vfs_write+0x54/0x14c <2> vfs_write+0xcc/0x188 <2> SyS_write+0x60/0xc0 <2> el0_svc_naked+0x34/0x38 device register call stack - <2> notifier_call_chain+0x84/0xbc <2> raw_notifier_call_chain+0x38/0x48 <2> call_netdevice_notifiers_info+0x40/0x70 <2> call_netdevice_notifiers+0x38/0x60 <2> register_netdevice+0x29c/0x3d8 <2> rmnet_vnd_newlink+0x68/0xe8 <2> rmnet_newlink+0xa0/0x160 <2> rtnl_newlink+0x57c/0x6c8 <2> rtnetlink_rcv_msg+0x1dc/0x328 <2> netlink_rcv_skb+0xac/0x118 <2> rtnetlink_rcv+0x24/0x30 <2> netlink_unicast+0x158/0x1f0 <2> netlink_sendmsg+0x32c/0x338 <2> sock_sendmsg+0x44/0x60 <2> SyS_sendto+0x150/0x1ac <2> el0_svc_naked+0x34/0x38 Fixes: b752eff5 ("net: qualcomm: rmnet: Implement ndo_get_iflink") Signed-off-by:
Sean Tranchetti <stranche@codeaurora.org> Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by:
-
Xin Long authored
[ Upstream commit 12480e3b ] According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to defined as SCTP_SS_FCFS or SCTP_SS_RR. SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch. Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations") Reported-by:
-
Holger Hoffstätte authored
[ Upstream commit 0432e833 ] Since 4.19 the following error in sysfs has appeared when using the r8169 NIC driver: $cd /sys/module/realtek/drivers $ls -l ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory [..garbled dir entries follow..] Apparently the forward slash in "10/100Mbps Ethernet" is interpreted as directory separator that leads nowhere, and was introduced in commit 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions"). Fix this by removing the offending slash in the driver name. Other drivers in net/phy seem to have the same problem, but I cannot test/verify them. Fixes: 513588dd ("net: phy: realtek: add RTL8201F phy-id and functions") Signed-off-by:
Holger Hoffstätte <holger@applied-asynchrony.com> Reviewed-by:
-
Andrew Lunn authored
[ Upstream commit a9049ff9 ] The mv88e6161 would sometime fail to probe with a timeout waiting for the switch to complete an operation. This operation is supposed to clear the statistics counters. However, due to a read/modify/write, without the needed mask, the operation actually carried out was more random, with invalid parameters, resulting in the switch not responding. We need to preserve the histogram mode bits, so apply a mask to keep them. Reported-by:
Chris Healy <Chris.Healy@zii.aero> Fixes: 40cff8fc ("net: dsa: mv88e6xxx: Fix stats histogram mode") Signed-off-by:
-
Denis Drozdov authored
[ Upstream commit acf3766b ] The mlx5e channels should be closed before mlx5i_uninit_underlay_qp puts the QP into RST (reset) state during mlx5i_close. Currently QP state incorrectly set to RST before channels got deactivated and closed, since mlx5_post_send request expects QP in RTS (Ready To Send) state. The fix is to keep QP in RTS state until mlx5e channels get closed and to reset QP afterwards. Also this fix is simply correct in order to keep the open/close flow symmetric, i.e mlx5i_init_underlay_qp() is called first thing at open, the correct thing to do is to call mlx5i_uninit_underlay_qp() last thing at close, which is exactly what this patch is doing. Fixes: dae37456 ("net/mlx5: Support for attaching multiple underlay QPs to root flow table") Signed-off-by:
Denis Drozdov <denisd@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Raed Salem authored
[ Upstream commit f2b18732 ] The commit "net/mlx5: Refactor accel IPSec code" introduced a bug where asynchronous short time change in hash key value by create/release SA context might happen during an asynchronous hash resize operation this could cause a subsequent remove SA context operation to fail as the key value used during resize is not the same key value used when remove SA context operation is invoked. This commit fixes the bug by defining the SA context hash key such that it includes only fields that never change during the lifetime of the SA context object. Fixes: d6c4f029 ("net/mlx5: Refactor accel IPSec code") Signed-off-by:
Raed Salem <raeds@mellanox.com> Reviewed-by:
Aviad Yehezkel <aviadye@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit f8504f4c ] This issue happens when trying to add an existent tunnel. It doesn't call sock_put() before returning -EEXIST to release the sock refcnt that was held by calling sock_hold() before the existence check. This patch is to fix it by holding the sock after doing the existence check. Fixes: f6cd651b ("l2tp: fix race in duplicate tunnel detection") Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 0d5b9311 ] Multiple cpus might attempt to insert a new fragment in rhashtable, if for example RPS is buggy, as reported by 배석진 in https://patchwork.ozlabs.org/patch/994601/ We use rhashtable_lookup_get_insert_key() instead of rhashtable_insert_fast() to let cpus losing the race free their own inet_frag_queue and use the one that was inserted by another cpu. Fixes: 648700f7 ("inet: frags: use rhashtables for reassembly units") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
배석진 <soukjin.bae@samsung.com> Signed-off-by:
-
Shay Agroskin authored
[ Upstream commit 64e28334 ] Querying interface FEC caps with 'ethtool [int]' after link reset throws warning regading link speed. This warning is not needed as there is already an indication in user space that the link is not up. Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration") Signed-off-by:
Shay Agroskin <shayag@mellanox.com> Signed-off-by:
-
Valentine Fatiev authored
[ Upstream commit 228c4cd0 ] Loopback test had fixed packet size, which can be bigger than configured MTU. Shorten the loopback packet size to be bigger than minimal MTU allowed by the device. Text field removed from struct 'mlx5ehdr' as redundant to allow send small packets as minimal allowed MTU. Fixes: d605d668 ("net/mlx5e: Add support for ethtool self diagnostics test") Signed-off-by:
Valentine Fatiev <valentinef@mellanox.com> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 83621b7d ] We get the match level (none, l2, l3, l4) while going over the match dissectors of an offloaded tc rule. When doing this, the match level enum and the not min inline enum values should be used, fix that. This worked accidentally b/c both enums have the same numerical values. Fixes: d708f902 ('net/mlx5e: Get the required HW match level while parsing TC flow matches') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 69fec325 ] This reverts commit 22d7be26. The dst's mtu in transport can be updated by a non sctp place like in xfrm where the MTU information didn't get synced between asoc, transport and dst, so it is still needed to do the pmtu check in sctp_packet_config. Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Moshe Shemesh authored
[ Upstream commit 0073c8f7 ] In case of striding RQ, we use MPWRQ (Multi Packet WQE RQ), which means that WQE (RX descriptor) can be used for many packets and so the WQE is much bigger than MTU. In virtualization setups where the port mtu can be larger than the vf mtu, if received packet is bigger than MTU, it won't be dropped by HW on too small receive WQE. If we use linear SKB in striding RQ, since each stride has room for mtu size payload and skb info, an oversized packet can lead to crash for crossing allocated page boundary upon the call to build_skb. So driver needs to check packet size and drop it. Introduce new SW rx counter, rx_oversize_pkts_sw_drop, which counts the number of packets dropped by the driver for being too large. As a new field is added to the RQ struct, re-open the channels whenever this field is being used in datapath (i.e., in the case of linear Striding RQ). Fixes: 619a8f2a ("net/mlx5e: Use linear SKB in Striding RQ") Signed-off-by:
Moshe Shemesh <moshe@mellanox.com> Reviewed-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Yuval Avnery authored
[ Upstream commit a1f240f1 ] When core driver enters deattach/attach flow after pci reset, Number of logical CPUs may have changed. As a result we need to update the cpu affiliated resource tables. 1. indirect rqt list 2. eq table Reproduction (PowerPC): echo 1000 > /sys/kernel/debug/powerpc/eeh_max_freezes ppc64_cpu --smt=on # Restart driver modprobe -r ... ; modprobe ... # Link up ifconfig ... # Only physical CPUs ppc64_cpu --smt=off # Inject PCI errors so PCI will reset - calling the pci error handler echo 0x8000000000000000 > /sys/kernel/debug/powerpc/<PCI BUS>/err_injct_inboundA Call trace when trying to add non-existing rqs to an indirect rqt: mlx5e_redirect_rqt+0x84/0x260 [mlx5_core] (unreliable) mlx5e_redirect_rqts+0x188/0x190 [mlx5_core] mlx5e_activate_priv_channels+0x488/0x570 [mlx5_core] mlx5e_open_locked+0xbc/0x140 [mlx5_core] mlx5e_open+0x50/0x130 [mlx5_core] mlx5e_nic_enable+0x174/0x1b0 [mlx5_core] mlx5e_attach_netdev+0x154/0x290 [mlx5_core] mlx5e_attach+0x88/0xd0 [mlx5_core] mlx5_attach_device+0x168/0x1e0 [mlx5_core] mlx5_load_one+0x1140/0x1210 [mlx5_core] mlx5_pci_resume+0x6c/0xf0 [mlx5_core] Create cq will fail when trying to use non-existing EQ. Fixes: 89d44f0a ("net/mlx5_core: Add pci error handlers to mlx5_core driver") Signed-off-by:
Yuval Avnery <yuvalav@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit 077ecd78 ] Currently, we are only supporting tc hw offloads when the eswitch support is compiled in, but we are not gating the adevertizment of the NETIF_F_HW_TC feature on this config being set. Fix it, and while doing that, also avoid dealing with the feature on ethtool when the config is not set. Fixes: e8f887ac ('net/mlx5e: Introduce tc offload support') Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit d3a80bb5 ] For the "all" ethertype we should not care whether the packet has vlans. Besides being wrong, the way we did it caused FW error for rules such as: tc filter add dev eth0 protocol all parent ffff: \ prio 1 flower skip_sw action drop b/c the matching meta-data (outer headers bit in struct mlx5_flow_spec) wasn't set. Fix that by matching on vlan non-existence only if we were also told to match on the ethertype. Fixes: cee26487 ('net/mlx5e: Set vlan masks for all offloaded TC rules') Signed-off-by:
Slava Ovsiienko <viacheslavo@mellanox.com> Reviewed-by:
Jianbo Liu <jianbol@mellanox.com> Reviewed-by:
-
Jon Maloy authored
[ Upstream commit 7ab412d3 ] When a link failure is detected locally, the link is reset, the flag link->in_session is set to false, and a RESET_MSG with the 'stopping' bit set is sent to the peer. The purpose of this bit is to inform the peer that this endpoint just is going down, and that the peer should handle the reception of this particular RESET message as a local failure. This forces the peer to accept another RESET or ACTIVATE message from this endpoint before it can re-establish the link. This again is necessary to ensure that link session numbers are properly exchanged before the link comes up again. If a failure is detected locally at the same time at the peer endpoint this will do the same, which is also a correct behavior. However, when receiving such messages, the endpoints will not distinguish between 'stopping' RESETs and ordinary ones when it comes to updating session numbers. Both endpoints will copy the received session number and set their 'in_session' flags to true at the reception, while they are still expecting another RESET from the peer before they can go ahead and re-establish. This is contradictory, since, after applying the validation check referred to below, the 'in_session' flag will cause rejection of all such messages, and the link will never come up again. We now fix this by not only handling received RESET/STOPPING messages as a local failure, but also by omitting to set a new session number and the 'in_session' flag in such cases. Fixes: 7ea817f4 ("tipc: check session number before accepting link protocol messages") Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Jakub Kicinski authored
[ Upstream commit 63c82997 ] TCA_FLOWER_KEY_ENC_OPTS and TCA_FLOWER_KEY_ENC_OPTS_MASK can only currently contain further nested attributes, which are parsed by hand, so the policy is never actually used resulting in a W=1 build warning: net/sched/cls_flower.c:492:1: warning: ‘enc_opts_policy’ defined but not used [-Wunused-const-variable=] enc_opts_policy[TCA_FLOWER_KEY_ENC_OPTS_MAX + 1] = { Add the validation anyway to avoid potential bugs when other attributes are added and to make the attribute structure slightly more clear. Validation will also set extact to point to bad attribute on error. Fixes: 0a6e7778 ("net/sched: allow flower to match tunnel options") Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Simon Horman <simon.horman@netronome.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Davide Caratti authored
[ Upstream commit 19ab6910 ] tcf_idr_check_alloc() can return a negative value, on allocation failures (-ENOMEM) or IDR exhaustion (-ENOSPC): don't leak keys_ex in these cases. Fixes: 0190c1d4 ("net: sched: atomically check-allocate action") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit 7cb6a2a2 ] A timing hazard exists when the network interface is stopped that allows a watchdog timeout to be processed by a separate core in parallel. This creates the potential for the timeout handler to wake the queues while the driver is shutting down, or access registers after their clocks have been removed. The more common case is that the watchdog timeout will produce a warning message which doesn't lead to a crash. The chances of this are greatly increased by the fact that bcm_sysport_netif_stop stops the transmit queues which can easily precipitate a watchdog time- out because of stale trans_start data in the queues. This commit corrects the behavior by ensuring that the watchdog timeout is disabled before enterring bcm_sysport_netif_stop. There are currently only two users of the bcm_sysport_netif_stop function: close and suspend. The close case already handles the issue by exiting the RUNNING state before invoking the driver close service. The suspend case now performs the netif_device_detach to exit the PRESENT state before the call to bcm_sysport_netif_stop rather than after it. These behaviors prevent any future scheduling of the driver timeout service during the window. The netif_tx_stop_all_queues function in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure synchronization with any transmit or timeout threads that may already be executing on other cores. For symmetry, the netif_device_attach call upon resume is moved to after the call to bcm_sysport_netif_start. Since it wakes the transmit queues it is not necessary to invoke netif_tx_start_all_queues from bcm_sysport_netif_start so it is moved into the driver open service. Fixes: 40755a0f ("net: systemport: add suspend and resume support") Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by:
-
Matthew Cover authored
[ Upstream commit 8ebebcba ] When writing packets to a descriptor associated with a combined queue, the packets should end up on that queue. Before this change all packets written to any descriptor associated with a tap interface end up on rx-0, even when the descriptor is associated with a different queue. The rx traffic can be generated by either of the following. 1. a simple tap program which spins up multiple queues and writes packets to each of the file descriptors 2. tx from a qemu vm with a tap multiqueue netdev The queue for rx traffic can be observed by either of the following (done on the hypervisor in the qemu case). 1. a simple netmap program which opens and reads from per-queue descriptors 2. configuring RPS and doing per-cpu captures with rxtxcpu Alternatively, if you printk() the return value of skb_get_rx_queue() just before each instance of netif_receive_skb() in tun.c, you will get 65535 for every skb. Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes the association between descriptor and rx queue. Signed-off-by:
Matthew Cover <matthew.cover@stackpath.com> Signed-off-by:
-
Jon Maloy authored
[ Upstream commit adba75be ] We get the following warning: [ 47.926140] 32-bit node address hash set to 2010a0a [ 47.927202] [ 47.927433] ================================ [ 47.928050] WARNING: inconsistent lock state [ 47.928661] 4.19.0+ #37 Tainted: G E [ 47.929346] -------------------------------- [ 47.929954] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 47.930116] swapper/3/0 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 47.930116] 00000000af8bc31e (&(&ht->lock)->rlock){+.?.}, at: rhashtable_walk_enter+0x36/0xb0 [ 47.930116] {SOFTIRQ-ON-W} state was registered at: [ 47.930116] _raw_spin_lock+0x29/0x60 [ 47.930116] rht_deferred_worker+0x556/0x810 [ 47.930116] process_one_work+0x1f5/0x540 [ 47.930116] worker_thread+0x64/0x3e0 [ 47.930116] kthread+0x112/0x150 [ 47.930116] ret_from_fork+0x3a/0x50 [ 47.930116] irq event stamp: 14044 [ 47.930116] hardirqs last enabled at (14044): [<ffffffff9a07fbba>] __local_bh_enable_ip+0x7a/0xf0 [ 47.938117] hardirqs last disabled at (14043): [<ffffffff9a07fb81>] __local_bh_enable_ip+0x41/0xf0 [ 47.938117] softirqs last enabled at (14028): [<ffffffff9a0803ee>] irq_enter+0x5e/0x60 [ 47.938117] softirqs last disabled at (14029): [<ffffffff9a0804a5>] irq_exit+0xb5/0xc0 [ 47.938117] [ 47.938117] other info that might help us debug this: [ 47.938117] Possible unsafe locking scenario: [ 47.938117] [ 47.938117] CPU0 [ 47.938117] ---- [ 47.938117] lock(&(&ht->lock)->rlock); [ 47.938117] <Interrupt> [ 47.938117] lock(&(&ht->lock)->rlock); [ 47.938117] [ 47.938117] *** DEADLOCK *** [ 47.938117] [ 47.938117] 2 locks held by swapper/3/0: [ 47.938117] #0: 0000000062c64f90 ((&d->timer)){+.-.}, at: call_timer_fn+0x5/0x280 [ 47.938117] #1: 00000000ee39619c (&(&d->lock)->rlock){+.-.}, at: tipc_disc_timeout+0xc8/0x540 [tipc] [ 47.938117] [ 47.938117] stack backtrace: [ 47.938117] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G E 4.19.0+ #37 [ 47.938117] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 47.938117] Call Trace: [ 47.938117] <IRQ> [ 47.938117] dump_stack+0x5e/0x8b [ 47.938117] print_usage_bug+0x1ed/0x1ff [ 47.938117] mark_lock+0x5b5/0x630 [ 47.938117] __lock_acquire+0x4c0/0x18f0 [ 47.938117] ? lock_acquire+0xa6/0x180 [ 47.938117] lock_acquire+0xa6/0x180 [ 47.938117] ? rhashtable_walk_enter+0x36/0xb0 [ 47.938117] _raw_spin_lock+0x29/0x60 [ 47.938117] ? rhashtable_walk_enter+0x36/0xb0 [ 47.938117] rhashtable_walk_enter+0x36/0xb0 [ 47.938117] tipc_sk_reinit+0xb0/0x410 [tipc] [ 47.938117] ? mark_held_locks+0x6f/0x90 [ 47.938117] ? __local_bh_enable_ip+0x7a/0xf0 [ 47.938117] ? lockdep_hardirqs_on+0x20/0x1a0 [ 47.938117] tipc_net_finalize+0xbf/0x180 [tipc] [ 47.938117] tipc_disc_timeout+0x509/0x540 [tipc] [ 47.938117] ? call_timer_fn+0x5/0x280 [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] call_timer_fn+0xa1/0x280 [ 47.938117] ? tipc_disc_msg_xmit.isra.19+0xa0/0xa0 [tipc] [ 47.938117] run_timer_softirq+0x1f2/0x4d0 [ 47.938117] __do_softirq+0xfc/0x413 [ 47.938117] irq_exit+0xb5/0xc0 [ 47.938117] smp_apic_timer_interrupt+0xac/0x210 [ 47.938117] apic_timer_interrupt+0xf/0x20 [ 47.938117] </IRQ> [ 47.938117] RIP: 0010:default_idle+0x1c/0x140 [ 47.938117] Code: 90 90 90 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 41 54 55 53 65 8b 2d d8 2b 74 65 0f 1f 44 00 00 e8 c6 2c 8b ff fb f4 <65> 8b 2d c5 2b 74 65 0f 1f 44 00 00 5b 5d 41 5c c3 65 8b 05 b4 2b [ 47.938117] RSP: 0018:ffffaf6ac0207ec8 EFLAGS: 00000206 ORIG_RAX: ffffffffffffff13 [ 47.938117] RAX: ffff8f5b3735e200 RBX: 0000000000000003 RCX: 0000000000000001 [ 47.938117] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff8f5b3735e200 [ 47.938117] RBP: 0000000000000003 R08: 0000000000000001 R09: 0000000000000000 [ 47.938117] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 [ 47.938117] R13: 0000000000000000 R14: ffff8f5b3735e200 R15: ffff8f5b3735e200 [ 47.938117] ? default_idle+0x1a/0x140 [ 47.938117] do_idle+0x1bc/0x280 [ 47.938117] cpu_startup_entry+0x19/0x20 [ 47.938117] start_secondary+0x187/0x1c0 [ 47.938117] secondary_startup_64+0xa4/0xb0 The reason seems to be that tipc_net_finalize()->tipc_sk_reinit() is calling the function rhashtable_walk_enter() within a timer interrupt. We fix this by executing tipc_net_finalize() in work queue context. Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
Jon Maloy authored
[ Upstream commit 1c1274a5 ] The code for reading ancillary data from a received buffer is assuming the buffer is linear. To make this assumption true we have to linearize the buffer before message data is read. Signed-off-by:
-
Siva Reddy Kallam authored
[ Upstream commit 59663e42 ] This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change ring and flow control paths. This patch solves the RX hang while doing continuous ring or flow control parameters with heavy traffic from peer. Signed-off-by:
Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Stephen Mallon authored
[ Upstream commit cadf9df2 ] During tcp coalescing ensure that the skb hardware timestamp refers to the highest sequence number data. Previously only the software timestamp was updated during coalescing. Signed-off-by:
Stephen Mallon <stephen.mallon@sydney.edu.au> Signed-off-by:
-
Xin Long authored
[ Upstream commit cc3ccf26 ] As rfc7496#section4.5 says about SCTP_PR_SUPPORTED: This socket option allows the enabling or disabling of the negotiation of PR-SCTP support for future associations. For existing associations, it allows one to query whether or not PR-SCTP support was negotiated on a particular association. It means only sctp sock's prsctp_enable can be set. Note that for the limitation of SCTP_{CURRENT|ALL}_ASSOC, we will add it when introducing SCTP_{FUTURE|CURRENT|ALL}_ASSOC for linux sctp in another patchset. v1->v2: - drop the params.assoc_id check as Neil suggested. Fixes: 28aa4c26 ("sctp: add SCTP_PR_SUPPORTED on sctp sockopt") Reported-by:
Ying Xu <yinxu@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 33d9a2c7 ] eth_type_trans() assumes initial value for skb->pkt_type is PACKET_HOST. This is indeed the value right after a fresh skb allocation. However, it is possible that GRO merged a packet with a different value (like PACKET_OTHERHOST in case macvlan is used), so we need to make sure napi->skb will have pkt_type set back to PACKET_HOST. Otherwise, valid packets might be dropped by the stack because their pkt_type is not PACKET_HOST. napi_reuse_skb() was added in commit 96e93eab ("gro: Add internal interfaces for VLAN"), but this bug always has been there. Fixes: 96e93eab ("gro: Add internal interfaces for VLAN") Signed-off-by:
-
Doug Berger authored
A timing hazard exists when the network interface is stopped that allows a watchdog timeout to be processed by a separate core in parallel. This creates the potential for the timeout handler to wake the queues while the driver is shutting down, or access registers after their clocks have been removed. The more common case is that the watchdog timeout will produce a warning message which doesn't lead to a crash. The chances of this are greatly increased by the fact that bcmgenet_netif_stop stops the transmit queues which can easily precipitate a watchdog time- out because of stale trans_start data in the queues. This commit corrects the behavior by ensuring that the watchdog timeout is disabled before enterring bcmgenet_netif_stop. There are currently only two users of the bcmgenet_netif_stop function: close and suspend. The close case already handles the issue by exiting the RUNNING state before invoking the driver close service. The suspend case now performs the netif_device_detach to exit the PRESENT state before the call to bcmgenet_netif_stop rather than after it. These behaviors prevent any future scheduling of the driver timeout service during the window. The netif_tx_stop_all_queues function in bcmgenet_netif_stop is replaced with netif_tx_disable to ensure synchronization with any transmit or timeout threads that may already be executing on other cores. For symmetry, the netif_device_attach call upon resume is moved to after the call to bcmgenet_netif_start. Since it wakes the transmit queues it is not necessary to invoke netif_tx_start_all_queues from bcmgenet_netif_start so it is moved into the driver open service. [ Upstream commit 09e805d2 ] Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
-
David Ahern authored
[ Upstream commit 7ddacfa5 ] Preethi reported that PMTU discovery for UDP/raw applications is not working in the presence of VRF when the socket is not bound to a device. The problem is that ip6_sk_update_pmtu does not consider the L3 domain of the skb device if the socket is not bound. Update the function to set oif to the L3 master device if relevant. Fixes: ca254490 ("net: Add VRF support to IPv6 stack") Reported-by:
Preethi Ramachandra <preethir@juniper.net> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 761f6026 ] These is no need to hold dst before calling rt6_remove_exception_rt(). The call to dst_hold_safe() in ip6_link_failure() was for ip6_del_rt(), which has been removed in Commit 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes"). Otherwise, it will cause a dst leak. This patch is to simply remove the dst_hold_safe() call before calling rt6_remove_exception_rt() and also do the same in ip6_del_cached_rt(). It's safe, because the removal of the exception that holds its dst's refcnt is protected by rt6_exception_lock. Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes") Fixes: 23fb93a4 ("net/ipv6: Cleanup exception and cache route handling") Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit 16f7eb2b ] The various types of tunnels running over IPv4 can ask to set the DF bit to do PMTU discovery. However, PMTU discovery is subject to the threshold set by the net.ipv4.route.min_pmtu sysctl, and is also disabled on routes with "mtu lock". In those cases, we shouldn't set the DF bit. This patch makes setting the DF bit conditional on the route's MTU locking state. This issue seems to be older than git history. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Michał Mirosław authored
[ Upstream commit e84b4794 ] Don't request tag insertion when it isn't present in outgoing skb. Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
-
