- 24 Sep, 2012 40 commits
-
-
Tej Parkash authored
In case of FW hung ISP83XX generates continuous pause frames which causes switch to disable port. Added fix to disable generating pause frames in case of FW hung Signed-off-by:
Tej Parkash <tej.parkash@qlogic.com> Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Manish Dusane authored
Issue: For ISP83XX risc_intr getting clear two times in case of polling mode. risc_intr getting clear from interrupt_service_routine() as well from process_mbox_intr() because of this driver may clear risc_intr without processing interrupt. Fix: Do not clear risc_intr from process_mbox_intr(). Signed-off-by:
Manish Dusane <manish.dusane@qlogic.com> Signed-off-by:
-
Nilesh Javali authored
Handle IDC Request Notify AEN and post IDC Acknowledgement while participating in Loopback IDC. Signed-off-by:
Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Issue: System panic on rmmod if probe_adapter had failed during driver load. Call Trace: [<ffffffffa071aa5a>] qla4xxx_abort_active_cmds+0x4a/0xa0 [qla4xxx] [<ffffffffa07224db>] qla4xxx_free_adapter+0x1b/0x1b0 [qla4xxx] [<ffffffffa073991f>] qla4xxx_remove_adapter+0x294/0x2c7 [qla4xxx] [<ffffffff812930b7>] pci_device_remove+0x37/0x70 [<ffffffff8135006f>] __device_release_driver+0x6f/0xe0 [<ffffffff813501a8>] driver_detach+0xc8/0xd0 [<ffffffff8134ef0e>] bus_remove_driver+0x8e/0x110 [<ffffffff81350972>] driver_unregister+0x62/0xa0 [<ffffffff812933c4>] pci_unregister_driver+0x44/0xb0 [<ffffffffa0739659>] qla4xxx_module_exit+0x15/0x47 [qla4xxx] [<ffffffff810addd4>] sys_delete_module+0x194/0x260 [<ffffffff8150326e>] ? do_page_fault+0x3e/0xa0 [<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b Fix: Do not cleanup resources on remove_adapter as they are cleaned up during probe_adapter exit. Signed-off-by:
-
Poornima Vonti authored
If IRQ allocation fails, it means system has run out of interrupt vectors, so fail probe_adapter in case of IRQ allocation failure and dont retry adapter initialization. Signed-off-by:
Poornima Vonti <poornima.vonti@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
For ISP82xx mixed interrupt mode is not supported. Hence prevent MSI/MSI-x from falling back to INTx mode. Signed-off-by:
-
Vikas Chaudhary authored
Camram is reset by FW to default values after reboot/cold boot/pci reset. In case of AER, PCI may need to reset so we need to set correct idc reg value after PCIE error. Signed-off-by:
-
Poornima Vonti authored
Issue: In qla4_8xxx_error_recovery() IDC lock recovery is initiated as IDC lock is held while enabling the interrupts Fix: Correctly handle IDC locking mechanism in qla4_8xxx_error_recovery(). Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Manish Dusane authored
Signed-off-by:
-
Bart Van Assche authored
A quote from SPC-4: "While in the unavailable primary target port asymmetric access state, the device server shall support those of the following commands that it supports while in the active/optimized state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence enable sending STPG to a target port group that is in the unavailable state. Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
Hannes Reinecke <hare@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Dan Williams authored
John reports: BUG: soft lockup - CPU#2 stuck for 23s! [kworker/u:8:2202] [..] Call Trace: [<ffffffff8141782a>] scsi_remove_target+0xda/0x1f0 [<ffffffff81421de5>] sas_rphy_remove+0x55/0x60 [<ffffffff81421e01>] sas_rphy_delete+0x11/0x20 [<ffffffff81421e35>] sas_port_delete+0x25/0x160 [<ffffffff814549a3>] mptsas_del_end_device+0x183/0x270 ...introduced by commit 3b661a92 "[SCSI] fix hot unplug vs async scan race". Don't restart lookup of more stargets in the multi-target case, just arrange to traverse the list once, on the assumption that new targets are always added at the end. There is no guarantee that the target will change state in scsi_target_reap() so we can end up spinning if we restart. Cc: <stable@vger.kernel.org> Acked-by:
Jack Wang <jack_wang@usish.com> LKML-Reference: <CAEhu1-6wq1YsNiscGMwP4ud0Q+MrViRzv=kcWCQSBNc8c68N5Q@mail.gmail.com> Reported-by:
John Drescher <drescherjm@gmail.com> Tested-by:
Dan Williams <djbw@fb.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
The length field in the host config packet is only 16-bit long, so passing it 0x10000 (64K which is our standard PAGE_SIZE) doesn't work and result in an empty config from the server. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: <stable@vger.kernel.org> Acked-by:
Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
Now that the iSeries code is gone the backend abstraction in this driver is no longer necessary, which allows us to consolidate the driver in one file. The side effect is that the module name is now ibmvscsi.ko which matches the driver hotplug name and fixes auto-load issues. [jejb:fix up checkpatch.pl errors] Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Move minidump code from qla4_8xxx_device_bootstrap() to new function qla4_8xxx_get_minidump() to make code more modular. Signed-off-by:
Lalit Chandivade <lalit.chandivade@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Issue: Device can go to READY state from COLD and skip INITIALIZATION, In this case driver will never set IDC version from function qla4_8xxx_device_bootstrap(). Fix: 1. Set IDC version at start of function qla4_82xx_need_reset_handler(). 2. Set IDC version only if we are 1st driver to load. 3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one place. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Remove following unused define:- QLA82XX_MINIDUMP_OCM0_SIZE QLA82XX_MINIDUMP_L1C_SIZE QLA82XX_MINIDUMP_L2C_SIZE QLA82XX_MINIDUMP_COMMON_STR_SIZE QLA82XX_MINIDUMP_FCOE_STR_SIZE QLA82XX_MINIDUMP_MEM_SIZE QLA82XX_MAX_ENTRY_HDR Added following new define to optimize code:- MIU_TA_CTL_WRITE_ENABLE MIU_TA_CTL_WRITE_START MIU_TA_CTL_START_ENABLE Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped ql4_attr_is_visible to qla4_attr_is_visible Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Martin Pitt authored
Add "removable" module parameter to set the "removable" attribute of any subsequently created debug block device. It is a writable driver option, so that you can switch between removable and "fixed" media block devices in between the add_host calls. This is useful for being able to test the different behaviour/required privileges in e. g. the udisks test suite. Signed-off-by:
Martin Pitt <martin.pitt@ubuntu.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
while processing the stop firmware mailbox command on driver unload, a interrupt is processed which causes kernel panic as the response queue is not valid. Fix is to clear the interrupt in free_adapter call just after disabling the interrupts. Signed-off-by:
-
Vikas Chaudhary authored
Fix following lockdep warning:- INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. Pid: 298, comm: modprobe Not tainted 3.6.0-rc1+ #13 Call Trace: [<c049f5c6>] register_lock_class+0x186/0x360 [<c06e2e39>] ? __dev_printk+0x139/0x280 [<c04a288a>] __lock_acquire+0x6a/0x450 [<c04a2cf4>] lock_acquire+0x84/0xf0 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx] [<c089a05b>] _raw_spin_lock_irqsave+0x4b/0x60 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx] [<f98bb0d0>] qla4xxx_post_work+0x20/0x60 [qla4xxx] [<f98bb1c9>] qla4xxx_post_aen_work+0x49/0x60 [qla4xxx] [<f98c6cf2>] qla4xxx_isr_decode_mailbox+0x3f2/0x780 [qla4xxx] [<f98c8493>] qla4_83xx_interrupt_service_routine+0x33/0x50 [qla4xxx] [<f98d0e49>] qla4_83xx_process_mbox_intr+0x29/0x40 [qla4xxx] [<f98c2031>] qla4xxx_mailbox_command+0x361/0x5d0 [qla4xxx] [<c08983c8>] ? mutex_unlock+0x8/0x10 [<f98c3e86>] qla4xxx_get_ifcb+0x66/0xb0 [qla4xxx] [<f98c3ef7>] qla4xxx_update_local_ifcb+0x27/0x100 [qla4xxx] [<f98c56af>] qla4xxx_initialize_fw_cb+0x2ff/0x3b0 [qla4xxx] [<c04150d0>] ? dma_generic_free_coherent+0x30/0x30 [<f98c0f70>] qla4xxx_init_firmware+0x40/0xf0 [qla4xxx] [<f98c10b6>] qla4xxx_initialize_adapter+0x96/0x120 [qla4xxx] [<f98d35cd>] qla4xxx_probe_adapter+0x378/0x855 [qla4xxx] [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180 [<c04a1a9b>] ? trace_hardirqs_on+0xb/0x10 [<c06ef403>] ? pm_runtime_enable+0x43/0x70 [<c062f042>] local_pci_probe+0x42/0xb0 [<c06300c0>] pci_device_probe+0x60/0x80 [<c06e6bb6>] really_probe+0x56/0x2e0 [<c089a5f2>] ? _raw_spin_unlock_irq+0x22/0x30 [<c06f0b02>] ? pm_runtime_barrier+0x52/0xb0 [<c06e6e77>] driver_probe_device+0x37/0x90 [<c0898281>] ? mutex_lock_nested+0x31/0x40 [<c06e6f51>] __driver_attach+0x81/0x90 [<c06e51e8>] bus_for_each_dev+0x48/0x70 [<c06e68e9>] driver_attach+0x19/0x20 [<c06e6ed0>] ? driver_probe_device+0x90/0x90 [<c06e637f>] bus_add_driver+0x18f/0x280 [<c062ff40>] ? pci_dev_put+0x20/0x20 [<c062ff40>] ? pci_dev_put+0x20/0x20 [<c06e7435>] driver_register+0x65/0x120 [<c061a3a2>] ? __raw_spin_lock_init+0x32/0x60 [<c06302f4>] __pci_register_driver+0x54/0xc0 [<f98e809e>] qla4xxx_module_init+0x9e/0xcd [qla4xxx] [<c040302f>] do_one_initcall+0x2f/0x170 [<f98e8000>] ? 0xf98e7fff [<c04ae025>] sys_init_module+0x75/0x1c0 [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180 [<c0609514>] ? trace_hardirqs_on_thunk+0xc/0x10 [<c08a141f>] sysenter_do_call+0x12/0x38 Signed-off-by:
-
Dave Jiang authored
We always assign a dummy task context to a port in order to address a silicon issue. We have 4 ports per controller. So when idle, there are always exactly 4 TCs "active". The adaptive interrupt coalescing code uses number of active TCs to figure out the coalescing values. However, we never hit "0" TCs because of the 4 dummy TCs. Putting in fix so that we calculate this correctly. Reported-by:
Dan Melnic <dan@seamicro.com> Signed-off-by:
Dave Jiang <dave.jiang@intel.com> Signed-off-by:
-
Jeff Skirvin authored
This commit fixes a driver bug for SSP tasks that require task management in the target after they complete in the SCU hardware. The problem was manifested in the function "isci_task_abort_task", which tests to see if the sas_task.lldd_task is non-NULL before allowing task management; this bug would always NULL lldd_task in the SCU I/O completion path even if target management was required, which would prevent task / target manangement from happening. Note that in the case of SATA/STP targets, error recovery is provided by the libata error handler which is why SATA/STP device recovery worked correctly even though SSP handling did not. Signed-off-by:
Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by:
-
Robert Love authored
This header file is included in user space applications that are doing "FC Passthrough." This include causes them to also include scsi/scsi.h. Since this header file doesn't actually need scsi/scsi.h, remove the include line. This patch was tested with 'make allyesconfig'. Signed-off-by:
Robert Love <robert.w.love@intel.com> Tested-by:
Ross Brattain <ross.b.brattain@intel.com> Signed-off-by:
-
Moger, Babu authored
Signed-off-by:
Babu Moger <babu.moger@netapp.com> Signed-off-by:
-
Moger, Babu authored
This patch consolidates the strings together. Purpose is to remove minor product strings extensions. That way the future products with similar strings should not require change here. Signed-off-by:
-
Moger, Babu authored
This patch adds a new vendor/product strings for netapp E series product. Also consolidated the strings together with similar names. Signed-off-by:
-
Martin Peschke authored
__scsi_remove_device (e.g. due to dev_loss_tmo) calls zfcp_scsi_slave_destroy which in turn sends a close LUN FSF request to the adapter. After 30 seconds without response, zfcp_erp_timeout_handler kicks the ERP thread failing the close LUN ERP action. zfcp_erp_wait in zfcp_erp_lun_shutdown_wait and thus zfcp_scsi_slave_destroy returns and then scsi_device is no longer valid. Sometime later the response to the close LUN FSF request may finally come in. However, commit b62a8d9b "[SCSI] zfcp: Use SCSI device data zfcp_scsi_dev instead of zfcp_unit" introduced a number of attempts to unconditionally access struct zfcp_scsi_dev through struct scsi_device causing a use-after-free. This leads to an Oops due to kernel page fault in one of: zfcp_fsf_abort_fcp_command_handler, zfcp_fsf_open_lun_handler, zfcp_fsf_close_lun_handler, zfcp_fsf_req_trace, zfcp_fsf_fcp_handler_common. Move dereferencing of zfcp private data zfcp_scsi_dev allocated in scsi_device via scsi_transport_reserve_device after the check for potentially aborted FSF request and thus no longer valid scsi_device. Only then assign sdev_to_zfcp(sdev) to the local auto variable struct zfcp_scsi_dev *zfcp_sdev. Signed-off-by:
Martin Peschke <mpeschke@linux.vnet.ibm.com> Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> #2.6.37+ Signed-off-by:
-
