Tony nguyen says:

====================
Intel Wired LAN Driver Updates 2023-05-16

This series contains updates to ice and iavf drivers.

Ahmed adds setting of missed condition for statistics which caused
incorrect reporting of values for ice. For iavf, he removes a call to set
VLAN offloads during re-initialization which can cause incorrect values
to be set.

Dawid adds checks to ensure VF is ready to be reset before executing
commands that will require it to be reset on ice.
---
v2:
Patch 2
- Redo commit message
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).

Fixes: de776d0d ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.

Add the missing vfree() to avoid a memory leak, should an error occur.

Fixes: fcaa4066 ("cassini: use request_firmware")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller reported [0] memory leaks of sk and skb related to the TUN
device with no repro, but we can reproduce it easily with:

  struct ifreq ifr = {}
  int fd_tun, fd_tmp;
  char buf[4] = {};

  fd_tun = openat(AT_FDCWD, "/dev/net/tun", O_WRONLY, 0);
  ifr.ifr_flags = IFF_TUN | IFF_NAPI | IFF_MULTI_QUEUE;
  ioctl(fd_tun, TUNSETIFF, &ifr);

  ifr.ifr_flags = IFF_DETACH_QUEUE;
  ioctl(fd_tun, TUNSETQUEUE, &ifr);

  fd_tmp = socket(AF_PACKET, SOCK_PACKET, 0);
  ifr.ifr_flags = IFF_UP;
  ioctl(fd_tmp, SIOCSIFFLAGS, &ifr);

  write(fd_tun, buf, sizeof(buf));
  close(fd_tun);

If we enable NAPI and multi-queue on a TUN device, we can put skb into
tfile->sk.sk_write_queue after the queue is detached.  We should prevent
it by checking tfile->detached before queuing skb.

Note this must be done under tfile->sk.sk_write_queue.lock because write()
and ioctl(IFF_DETACH_QUEUE) can run concurrently.  Otherwise, there would
be a small race window:

  write()                             ioctl(IFF_DETACH_QUEUE)
  `- tun_get_user                     `- __tun_detach
     |- if (tfile->detached)             |- tun_disable_queue
     |  `-> false                        |  `- tfile->detached = tun
     |                                   `- tun_queue_purge
     |- spin_lock_bh(&queue->lock)
     `- __skb_queue_tail(queue, skb)

Another solution is to call tun_queue_purge() when closing and
reattaching the detached queue, but it could paper over another
problems.  Also, we do the same kind of test for IFF_NAPI_FRAGS.

[0]:
unreferenced object 0xffff88801edbc800 (size 2048):
  comm "syz-executor.1", pid 33269, jiffies 4295743834 (age 18.756s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 07 40 00 00 00 00 00 00 00 00 00 00 00 00  ...@............
  backtrace:
    [<000000008c16ea3d>] __do_kmalloc_node mm/slab_common.c:965 [inline]
    [<000000008c16ea3d>] __kmalloc+0x4a/0x130 mm/slab_common.c:979
    [<000000003addde56>] kmalloc include/linux/slab.h:563 [inline]
    [<000000003addde56>] sk_prot_alloc+0xef/0x1b0 net/core/sock.c:2035
    [<000000003e20621f>] sk_alloc+0x36/0x2f0 net/core/sock.c:2088
    [<0000000028e43843>] tun_chr_open+0x3d/0x190 drivers/net/tun.c:3438
    [<000000001b0f1f28>] misc_open+0x1a6/0x1f0 drivers/char/misc.c:165
    [<000000004376f706>] chrdev_open+0x111/0x300 fs/char_dev.c:414
    [<00000000614d379f>] do_dentry_open+0x2f9/0x750 fs/open.c:920
    [<000000008eb24774>] do_open fs/namei.c:3636 [inline]
    [<000000008eb24774>] path_openat+0x143f/0x1a30 fs/namei.c:3791
    [<00000000955077b5>] do_filp_open+0xce/0x1c0 fs/namei.c:3818
    [<00000000b78973b0>] do_sys_openat2+0xf0/0x260 fs/open.c:1356
    [<00000000057be699>] do_sys_open fs/open.c:1372 [inline]
    [<00000000057be699>] __do_sys_openat fs/open.c:1388 [inline]
    [<00000000057be699>] __se_sys_openat fs/open.c:1383 [inline]
    [<00000000057be699>] __x64_sys_openat+0x83/0xf0 fs/open.c:1383
    [<00000000a7d2182d>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<00000000a7d2182d>] do_syscall_64+0x3c/0x90 arch/x86/entry/common.c:80
    [<000000004cc4e8c4>] entry_SYSCALL_64_after_hwframe+0x72/0xdc

unreferenced object 0xffff88802f671700 (size 240):
  comm "syz-executor.1", pid 33269, jiffies 4295743854 (age 18.736s)
  hex dump (first 32 bytes):
    68 c9 db 1e 80 88 ff ff 68 c9 db 1e 80 88 ff ff  h.......h.......
    00 c0 7b 2f 80 88 ff ff 00 c8 db 1e 80 88 ff ff  ..{/............
  backtrace:
    [<00000000e9d9fdb6>] __alloc_skb+0x223/0x250 net/core/skbuff.c:644
    [<000000002c3e4e0b>] alloc_skb include/linux/skbuff.h:1288 [inline]
    [<000000002c3e4e0b>] alloc_skb_with_frags+0x6f/0x350 net/core/skbuff.c:6378
    [<00000000825f98d7>] sock_alloc_send_pskb+0x3ac/0x3e0 net/core/sock.c:2729
    [<00000000e9eb3df3>] tun_alloc_skb drivers/net/tun.c:1529 [inline]
    [<00000000e9eb3df3>] tun_get_user+0x5e1/0x1f90 drivers/net/tun.c:1841
    [<0000000053096912>] tun_chr_write_iter+0xac/0x120 drivers/net/tun.c:2035
    [<00000000b9282ae0>] call_write_iter include/linux/fs.h:1868 [inline]
    [<00000000b9282ae0>] new_sync_write fs/read_write.c:491 [inline]
    [<00000000b9282ae0>] vfs_write+0x40f/0x530 fs/read_write.c:584
    [<00000000524566e4>] ksys_write+0xa1/0x170 fs/read_write.c:637
    [<00000000a7d2182d>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<00000000a7d2182d>] do_syscall_64+0x3c/0x90 arch/x86/entry/common.c:80
    [<000000004cc4e8c4>] entry_SYSCALL_64_after_hwframe+0x72/0xdc

Fixes: cde8b15f ("tuntap: add ioctl to attach or detach a file form tuntap device")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2023-05-16

1) Don't check the policy default if we have an allow
   policy. Fix from Sabrina Dubroca.

2) Fix netdevice refount usage on offload.
   From Leon Romanovsky.

3) Use netdev_put instead of dev_puti to correctly release
   the netdev on failure in xfrm_dev_policy_add.
   From Leon Romanovsky.

4) Revert "Fix XFRM-I support for nested ESP tunnels"
   This broke Netfilter policy matching.
   From Martin Willi.

5) Reject optional tunnel/BEET mode templates in outbound policies
   on netlink and pfkey sockets. From Tobias Brunner.

6) Check if_id in inbound policy/secpath match to make
   it symetric to the outbound codepath.
   From Benedict Wong.

* tag 'ipsec-2023-05-16' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec:
  xfrm: Check if_id in inbound policy/secpath match
  af_key: Reject optional tunnel/BEET mode templates in outbound policies
  xfrm: Reject optional tunnel/BEET mode templates in outbound policies
  Revert "Fix XFRM-I support for nested ESP tunnels"
  xfrm: Fix leak of dev tracker
  xfrm: release all offloaded policy memory
  xfrm: don't check the default policy if the policy allows the packet
====================

Link: https://lore.kernel.org/r/20230516052405.2677554-1-steffen.klassert@secunet.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-fixes-for-6.4-20230515' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2023-05-15

The first 2 patches are by Oliver Hartkopp and allow the
MSG_CMSG_COMPAT flag for isotp and j1939.

The next patch is by Oliver Hartkopp, too and adds missing CAN XL
support in can_put_echo_skb().

Geert Uytterhoeven's patch let's the bxcan driver depend on
ARCH_STM32.

The last 5 patches are from Dario Binacchi and also affect the bxcan
driver. The bxcan driver hit mainline with v6.4-rc1 and was originally
written for IP cores containing 2 CAN interfaces with shared
resources. Dario's series updates the DT bindings and driver to
support IP cores with a single CAN interface instance as well as
adding the bxcan to the stm32f746's device tree.

* tag 'linux-can-fixes-for-6.4-20230515' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
  ARM: dts: stm32: add CAN support on stm32f746
  can: bxcan: add support for single peripheral configuration
  ARM: dts: stm32: add pin map for CAN controller on stm32f7
  ARM: dts: stm32f429: put can2 in secondary mode
  dt-bindings: net: can: add "st,can-secondary" property
  can: CAN_BXCAN should depend on ARCH_STM32
  can: dev: fix missing CAN XL support in can_put_echo_skb()
  can: j1939: recvmsg(): allow MSG_CMSG_COMPAT flag
  can: isotp: recvmsg(): allow MSG_CMSG_COMPAT flag
====================

Link: https://lore.kernel.org/r/20230515204722.1000957-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

'__net_initdata' becomes a no-op with CONFIG_NET_NS=y, but when this
option is disabled it becomes '__initdata', which means the data can be
freed after the initialization phase. This annotation is obviously
incorrect for the devlink net device notifier block which is still
registered after the initialization phase [1].

Fix this crash by removing the '__net_initdata' annotation.

[1]
general protection fault, probably for non-canonical address 0xcccccccccccccccc: 0000 [#1] PREEMPT SMP
CPU: 3 PID: 117 Comm: (udev-worker) Not tainted 6.4.0-rc1-custom-gdf0acdc5 #64
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-1.fc37 04/01/2014
RIP: 0010:notifier_call_chain+0x58/0xc0
[...]
Call Trace:
 <TASK>
 dev_set_mac_address+0x85/0x120
 dev_set_mac_address_user+0x30/0x50
 do_setlink+0x219/0x1270
 rtnl_setlink+0xf7/0x1a0
 rtnetlink_rcv_msg+0x142/0x390
 netlink_rcv_skb+0x58/0x100
 netlink_unicast+0x188/0x270
 netlink_sendmsg+0x214/0x470
 __sys_sendto+0x12f/0x1a0
 __x64_sys_sendto+0x24/0x30
 do_syscall_64+0x38/0x80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: e93c9378 ("devlink: change per-devlink netdev notifier to static one")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/netdev/600ddf9e-589a-2aa0-7b69-a438f833ca10@samsung.com/Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230515162925.1144416-1-idosch@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.

Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
    iavf_set_vlan_offload_features(adapter, 0, netdev->features);

The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING

While the first step forces the watchdog task to call
netdev_update_features() ->  iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING

When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.

Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.

Fixes: 7598f4b4 ("iavf: Move netdev_update_features() into watchdog task")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix the current implementation that causes ice_trigger_vf_reset()
to start resetting the VF even when the VF-NIC is still initializing.

When we reset NIC with ice driver it can interfere with
iavf-vf initialization e.g. during consecutive resets induced by ice

iavf                ice
  |                  |
  |<-----------------|
  |            ice resets vf
 iavf                |
 reset               |
 start               |
  |<-----------------|
  |             ice resets vf
  |             causing iavf
  |             initialization
  |             error
  |                  |
 iavf
 reset
 end

This leads to a series of -53 errors
(failed to init adminq) from the IAVF.

Change the state of the vf_state field to be not active when the IAVF
is still initializing. Make sure to wait until receiving the message on
the message box to ensure that the vf is ready and initializded.

In simple terms we use the ACTIVE flag to make sure that the ice
driver knows if the iavf is ready for another reset

  iavf                  ice
    |                    |
    |                    |
    |<------------- ice resets vf
  iavf           vf_state != ACTIVE
  reset                  |
  start                  |
    |                    |
    |                    |
  iavf                   |
  reset-------> vf_state == ACTIVE
  end              ice resets vf
    |                    |
    |                    |

Fixes: c54d209c ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

After a core PF reset, the VFs were showing wrong Rx/Tx stats. This is a
regression in commit 6624e780 ("ice: split ice_vsi_setup into smaller
functions") caused by missing to set "stat_offsets_loaded = false" in the
ice_vsi_rebuild() path.

Fixes: 6624e780 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().

Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.

Fixes: c96e731c ("net: bcmgenet: connect and disconnect from the PHY state machine")
Fixes: 93e0401e ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Dario Binacchi <dario.binacchi@amarulasolutions.com> says:

The series adds support for managing bxCAN controllers in single peripheral
configuration.
Unlike stm32f4 SOCs, where bxCAN controllers are only in dual peripheral
configuration, stm32f7 SOCs contain three CAN peripherals, CAN1 and CAN2
in dual peripheral configuration and CAN3 in single peripheral
configuration:
- Dual CAN peripheral configuration:
 * CAN1: Primary bxCAN for managing the communication between a secondary
   bxCAN and the 512-byte SRAM memory.
 * CAN2: Secondary bxCAN with no direct access to the SRAM memory.
   This means that the two bxCAN cells share the 512-byte SRAM memory and
   CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
 * CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
   512-byte SRAM memory.

The driver has been tested on the stm32f769i-discovery board with a
kernel version 5.19.0-rc2 in loopback + silent mode:

| ip link set can[0-2] type can bitrate 125000 loopback on listen-only on
| ip link set up can[0-2]
| candump can[0-2] -L &
| cansend can[0-2] 300#AC.AB.AD.AE.75.49.AD.D1

Changes in v2:
- s/fiter/filter/ in the commit message
- Replace struct bxcan_mb::primary with struct bxcan_mb::cfg.
- Move after the patch "can: bxcan: add support for single peripheral configuration".
- Add node gcan3.
- Rename gcan as gcan1.
- Add property "st,can-secondary" to can2 node.
- Drop patch "dt-bindings: mfd: stm32f7: add binding definition for CAN3"
  because it has been accepted.
- Add patch "ARM: dts: stm32f429: put can2 in secondary mode".
- Add patch "dt-bindings: net: can: add "st,can-secondary" property".

v1: https://lore.kernel.org/all/20230423172528.1398158-1-dario.binacchi@amarulasolutions.com

Link: https://lore.kernel.org/all/20230427204540.3126234-1-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
  * CAN1: Primary bxCAN for managing the communication between a secondary
    bxCAN and the 512-byte SRAM memory.
  * CAN2: Secondary bxCAN with no direct access to the SRAM memory.
  This means that the two bxCAN cells share the 512-byte SRAM memory and
  CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
  * CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
    512-byte SRAM memory.

 -------------------------------------------------------------------------
| features | CAN1              | CAN2               | CAN 3               |
 -------------------------------------------------------------------------
| SRAM     | 512-byte shared between CAN1 & CAN2    | 512-byte            |
 -------------------------------------------------------------------------
| Filters  | 26 filters shared between CAN1 & CAN2  | 14 filters          |
 -------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support for bxCAN controller in single peripheral configuration:
- primary bxCAN
- dedicated Memory Access Controller unit
- 512-byte SRAM memory
- 14 filter banks
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-5-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add pin configurations for using CAN controller on stm32f7.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-4-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This is a preparation patch for the upcoming support to manage CAN
peripherals in single configuration.

The addition ensures backwards compatibility.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-3-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On the stm32f7 Socs the can peripheral can be in single or dual
configuration. In the dual configuration, in turn, it can be in primary
or secondary mode. The addition of the 'st,can-secondary' property allows
you to specify this mode in the dual configuration.

CAN peripheral nodes in single configuration contain neither
"st,can-primary" nor "st,can-secondary".
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/all/20230427204540.3126234-2-dario.binacchi@amarulasolutions.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The STMicroelectronics STM32 basic extended CAN Controller (bxCAN) is
only present on STM32 SoCs.  Hence drop the "|| OF" part from its
dependency rule, to prevent asking the user about this driver when
configuring a kernel without STM32 SoC support.

Fixes: f00647d8 ("can: bxcan: add support for ST bxCAN controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/all/40095112efd1b2214e4223109fd9f0c6d0158a2d.1680609318.git.geert+renesas@glider.beSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

can_put_echo_skb() checks for the enabled IFF_ECHO flag and the
correct ETH_P type of the given skbuff. When implementing the CAN XL
support the new check for ETH_P_CANXL has been forgotten.

Fixes: fb08cba1 ("can: canxl: update CAN infrastructure for CAN XL frames")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230506184515.39241-1-socketcan@hartkopp.netSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The control message provided by J1939 support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.

Link: https://github.com/hartkopp/can-isotp/issues/59
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/20230505110308.81087-3-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The control message provided by isotp support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.

Link: https://github.com/hartkopp/can-isotp/issues/59
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: 42bf50a1 ("can: isotp: support MSG_TRUNC flag when reading from socket")
Link: https://lore.kernel.org/20230505110308.81087-2-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

While testing a Fiberstore SFP-10G-T module (which uses 10GBASE-R with
rate adaption) in a Clearfog platform (which can't do that) it was
found that the PHYs advertisement was not limited according to the
hosts capabilities when using ethtool to change it.

Fix this by ensuring that we mask the advertisement with the computed
support mask as the very first thing we do.

Fixes: cbc1bb1e ("net: phylink: simplify phy case for ksettings_set method")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
tipc: fix the mtu update in link mtu negotiation

This patchset fixes a crash caused by a too small MTU carried in the
activate msg. Note that as such malicious packet does not exist in
the normal env, the fix won't break any application

The 1st patch introduces a function to calculate the minimum MTU for
the bearer, and the 2nd patch fixes the crash with this helper. While
at it, the 3rd patch fixes the udp bearer mtu update by netlink with
this helper.
====================
Reviewed-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checking the bearer min mtu with tipc_udp_mtu_bad() only works for
IPv4 UDP bearer, and IPv6 UDP bearer has a different value for the
min mtu. This patch checks with encap_hlen + TIPC_MIN_BEARER_MTU
for min mtu, which works for both IPv4 and IPv6 UDP bearer.

Note that tipc_udp_mtu_bad() is still used to check media min mtu
in __tipc_nl_media_set(), as m->mtu currently is only used by the
IPv4 UDP bearer as its default mtu value.

Fixes: 682cd3cf ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When doing link mtu negotiation, a malicious peer may send Activate msg
with a very small mtu, e.g. 4 in Shuang's testing, without checking for
the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then
n->links[bearer_id].mtu is set to 4294967228, which is a overflow of
'4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss().

With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning:

 tipc: Too large msg, purging xmit list 1 5 0 40 4!
 tipc: Too large msg, purging xmit list 1 15 0 60 4!

And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in
named_distribute(), and when purging it in tipc_link_xmit(), a crash
was even caused:

  general protection fault, probably for non-canonical address 0x2100001011000dd: 0000 [#1] PREEMPT SMP PTI
  CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.3.0.neta #19
  RIP: 0010:kfree_skb_list_reason+0x7e/0x1f0
  Call Trace:
   <IRQ>
   skb_release_data+0xf9/0x1d0
   kfree_skb_reason+0x40/0x100
   tipc_link_xmit+0x57a/0x740 [tipc]
   tipc_node_xmit+0x16c/0x5c0 [tipc]
   tipc_named_node_up+0x27f/0x2c0 [tipc]
   tipc_node_write_unlock+0x149/0x170 [tipc]
   tipc_rcv+0x608/0x740 [tipc]
   tipc_udp_recv+0xdc/0x1f0 [tipc]
   udp_queue_rcv_one_skb+0x33e/0x620
   udp_unicast_rcv_skb.isra.72+0x75/0x90
   __udp4_lib_rcv+0x56d/0xc20
   ip_protocol_deliver_rcu+0x100/0x2d0

This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(),
and not updating mtu if it is too small.

Fixes: ed193ece ("tipc: simplify link mtu negotiation")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As different media may requires different min mtu, and even the
same media with different net family requires different min mtu,
add tipc_bearer_min_mtu() to calculate min mtu accordingly.

This API will be used to check the new mtu when doing the link
mtu negotiation in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 87e3bee0 ("net: mdio: i2c: Separate C22 and C45 transactions")
separated the non-rollball bus accessors, but left the rollball
accessors as is. As rollball accessors are clause 45, this results
in the rollball protocol being completely non-functional. Fix this.

Fixes: 87e3bee0 ("net: mdio: i2c: Separate C22 and C45 transactions")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.

Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.

Fixes: 754b8a21 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.

Fixes: 26312c68 ("net: fec: correct the counting of XDP sent frames")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():

invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
 skb_push+0x91/0xa0
 nsh_gso_segment+0x4f3/0x570
 skb_mac_gso_segment+0x19e/0x270
 __skb_gso_segment+0x1e8/0x3c0
 validate_xmit_skb+0x452/0x890
 validate_xmit_skb_list+0x99/0xd0
 sch_direct_xmit+0x294/0x7c0
 __dev_queue_xmit+0x16f0/0x1d70
 packet_xmit+0x185/0x210
 packet_snd+0xc15/0x1170
 packet_sendmsg+0x7b/0xa0
 sock_sendmsg+0x14f/0x160

The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.

nsh_gso_segment
    nhoff = skb->network_header - skb->mac_header;
    __skb_pull(skb,nsh_len)
    skb_mac_gso_segment
        mpls_gso_segment
            skb_reset_network_header(skb);//skb->network_header+=nsh_len
            return -EINVAL;
    skb_gso_error_unwind
        skb_push(skb, nsh_len);
        skb->mac_header = skb->network_header - nhoff;
        // skb->mac_header > skb->headroom, cause skb_push panic

Use correct mac_offset to restore mac_header and get rid of nhoff.

Fixes: c411ed85 ("nsh: add GSO support")
Reported-by: syzbot+632b5d9964208bfef8c0@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hao Lan says:

====================
net: hns3: fix some bug for hns3

There are some bugfixes for the HNS3 ethernet driver. patch#1 fix miss
checking for rx packet. patch#2 fixes VF promisc mode not update
when mac table full bug, and patch#3 fixes a nterrupts not
initialization in VF FLR bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.

Fixes: 8d307f8e ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.

According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.

Fixes: 6988eb2a ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.

Fixes: 35d93a30 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.

So fix it by increasing the tx queue print buffer length.

Fixes: 630a6738 ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexis Lothoré says:

====================
net: dsa: rzn1-a5psw: fix STP states handling

This small series fixes STP support and while adding a new function to
enable/disable learning, use that to disable learning on standalone ports
at switch setup as reported by Vladimir Oltean.

This series was initially submitted on net-next by Clement Leger, but some
career evolutions has made him hand me over those topics.
Also, this new revision is submitted on net instead of net-next for V1
based on Vladimir Oltean's suggestion

Changes since v2:
- fix commit split by moving A5PSW_MGMT_CFG_ENABLE in relevant commit
- fix reverse christmas tree ordering in a5psw_port_stp_state_set

Changes since v1:
- fix typos in commit messages and doc
- re-split STP states handling commit
- add Fixes: tag and new Signed-off-by
- submit series as fix on net instead of net-next
- split learning and blocking setting functions
- remove unused define A5PSW_PORT_ENA_TX_SHIFT
- add boolean for tx/rx enabled for clarity
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.

Fixes: 888cdb89 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.

Fixes: 888cdb89 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.

Fixes: 888cdb89 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 20704bd1 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.

Thanks to Kevin for pointing this out.

Fixes: 20704bd1 ("erspan: build the header with the right proto according to erspan_ver")
Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support")
Reported-by: Kevin Traynor <ktraynor@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>