- 28 Apr, 2007 10 commits
-
-
Dmitriy Monakhov authored
Since commit:553c4aa6 ata_pci_device_do_resume() can return error code, all callers was updated except this one. Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Robert Hancock authored
Warn the user if a drive's transfer rate is limited because of a 40-wire cable detection. Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Mark Lord authored
Resending, with s/printk/DPRINTK/ as pointed out by Alan. Fix libata to perform CDB len validation per device rather than per host. This way, validation still works when we have a mix of 12-byte and 16-byte devices on a common host interface. Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Alan authored
It used to be impossible to get from ata_device to ata_port but that is no longer true. Various methods have been cleaned up over time but dev_config still takes both and most users don't need both anyway. Tidy this one up Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Jeff Garzik authored
The chips covered by sata_mv have a 32-bit DMA boundary they must not cross, not a 64K boundary. We are merely limited to a 64K maximum segment size. Therefore, the DMA scatter/gather table fill code can be greatly simplified, and we need not cut in half the S/G table size as reported to the SCSI layer. Also, the driver forget to turn on 64-bit DMA at the PCI layer. All other data structures (both hardware and software) have been prepped for 64-bit PCI DMA. It was simply never turned on. <fingers crossed> let's see if it still works... Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Jeff Garzik authored
To be used in sata_mv's exception handling code, and overall is a generally useful function. Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Jeff Garzik authored
Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Linus Torvalds authored
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: sis900: Allocate rx replacement buffer before rx operation usb-net/pegasus: simplify carrier detection
-
Neil Horman authored
Just found a hole in my last patch. It was reported to me that shortly after we integrated this patch. The report was of an oops that took place inside of netif_rx when using the sis900 driver. Looking at my origional patch I noted that there was a spot between the new skb_alloc and the refill_rx_ring label where skb got reassigned to the pointer currently held in the rx_ring for the purposes of receiveing the frame. The result of this is however that the buffer that gets passed to netif_rx (if it is called), then gets placed right back into the rx_ring. So if you receive frames fast enough the skb being processed by the network stack can get corrupted. The reporter is testing out the fix I've written for this below (I'm not near my hardware at the moment to test myself), but I wanted to post it for review ASAP. I'll post test results when I hear them, but I think this is a pretty straightforward fix. It just uses a separate pointer to do the rx operation, so that we don't improperly reassign the pointer that we use to refill the rx ring. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
Dan Williams authored
Simplify pegasus carrier detection; rely only on the periodic MII polling. Reverts pieces of c43c49bd. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
-
- 27 Apr, 2007 30 commits
-
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SCSI] esp_scsi.c: Fix compilation.
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [NET]: Fix networking compilation errors [AF_RXRPC/AFS]: Arch-specific fixes. [AFS]: Fix VLocation record update wakeup [NET]: Revert sk_buff walker cleanups.
-
git://git.infradead.org/mtd-2.6Linus Torvalds authored
* git://git.infradead.org/mtd-2.6: (46 commits) [MTD] [MAPS] drivers/mtd/maps/ck804xrom.c: convert pci_module_init() [MTD] [NAND] CM-x270 MTD driver [MTD] [NAND] Wrong calculation of page number in nand_block_bad() [MTD] [MAPS] fix plat-ram printk format [JFFS2] Fix compr_rubin.c build after include file elimination. [JFFS2] Handle inodes with only a single metadata node with non-zero isize [JFFS2] Tidy up licensing/copyright boilerplate. [MTD] [OneNAND] Exit loop only when column start with 0 [MTD] [OneNAND] Fix access the past of the real oobfree array [MTD] [OneNAND] Update Samsung OneNAND official URL [JFFS2] Better fix for all-zero node headers [JFFS2] Improve read_inode memory usage, v2. [JFFS2] Improve failure mode if inode checking leaves unchecked space. [JFFS2] Fix cross-endian build. [MTD] Finish conversion mtd_blkdevs to use the kthread API [JFFS2] Obsolete dirent nodes immediately on unlink, where possible. Use menuconfig objects: MTD [MTD] mtd_blkdevs: Convert to use the kthread API [MTD] Fix fwh_lock locking [JFFS2] Speed up mount for directly-mapped NOR flash ...
-
Adrian Bunk authored
This patch converts the pci_module_init() usage to pci_register_driver(). It's currently #if 0'ed, but still not a bad idea to change it. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
-
David Howells authored
Fix miscellaneous networking compilation errors. (*) Export ktime_add_ns() for modules. (*) wext_proc_init() should have an ANSI declaration. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David Howells authored
Fixes for various arch compilation problems: (*) Missing module exports. (*) Variable name collision when rxkad and af_rxrpc both built in (rxrpc_debug). (*) Large constant representation problem (AFS_UUID_TO_UNIX_TIME). (*) Configuration dependencies. (*) printk() format warnings. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David Howells authored
Fix the wakeup transitions after a VLocation record update completes one way or another. This builds on Dave Miller's partial fix. Also move wakeups outside the spinlocked sections. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
This reverts eefa3906 The simplification made in that change works with the assumption that the 'offset' parameter to these functions is always positive or zero, which is not true. It can be and often is negative in order to access SKB header values in front of skb->data. Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexey Dobriyan authored
irqreturn.h for irqreturn_t and dma_addr_t being u128 warnings ;-) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Mike Rapoport authored
This patch provides MTD support for NAND flash devices on CM-x270 modules. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (78 commits) USB: update MAINAINERS and CREDITS for Freescale USB driver USB: update gadget files for fsl_usb2_udc driver USB: add Freescale high-speed USB SOC device controller driver USB: quirk for broken suspend of IT8152F/G USB: iowarrior.c: timeouts too small in usb_control_msg calls USB: dell device id for option.c USB: Remove Huawei unusual_devs entry USB: CP2101 New Device IDs USB: add picdem device to ldusb usbfs micro optimitation USB: remove ancient/broken CRIS hcd usb ethernet gadget, workaround network stack API glitch USB: add "busnum" attribute for USB devices USB: cxacru: ADSL state management usbatm: Detect usb device shutdown and ignore failed urbs USB: Remove duplicate define of OHCI_QUIRK_ZFMICRO USB: BandRich BandLuxe HSDPA Data Card Driver USB gadget rndis: fix struct rndis_packet_msg_type unaligned bug USB Elan FTDI: check for driver registration status USB: sierra: add more checks on shutdown ...
-
ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvbLinus Torvalds authored
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (184 commits) V4L/DVB (5563): Radio-maestro.c Replace radio_ioctl to use video_ioctl2 V4L/DVB (5562): Radio-gemtek-pci.c Replace gemtek_pci_ioctl to use video_ioctl2 V4L/DVB (5560): Ivtv: fix incorrect bitwise-and for command flags. V4L/DVB (5558): Opera: use 7-bit i2c addresses V4L/DVB (5557): Cafe_ccic: check return value of pci_enable_device V4L/DVB (5556): Radio-gemtek.c Replace gemtek_ioctl to use video_ioctl2 V4L/DVB (5555): Radio-aimslab.c Replace rt_ioctl to use video_ioctl2 V4L/DVB (5554): Fix: vidioc_g_parm were not zeroing the memory V4L/DVB (5553): Replace typhoon_do_ioctl to use video_ioctl2 V4L/DVB (5552): Plan-b: Switch to refcounting PCI API V4L/DVB (5551): Plan-b: header change V4L/DVB (5550): Radio-sf16fmi.c Replace fmi_do_ioctl to use video_ioctl2 V4L/DVB (5549): Radio-sf16fmr2.c Replace fmr2_do_ioctl to use video_ioctl2 V4L/DVB (5548): Fix v4l2 buffer to the length V4L/DVB (5547): Add ENUM_FRAMESIZES and ENUM_FRAMEINTERVALS ioctls V4L/DVB (5546): Radio-terratec.c Replace tt_do_ioctl to use video_ioctl2 V4L/DVB (5545): Saa7146: Release capture buffers on device close V4L/DVB (5544): Budget-av: Make inversion setting configurable, add KNC ONE V1.0 card V4L/DVB (5543): Tda10023: Add support for frontend TDA10023 V4L/DVB (5542): Budget-av: Remove polarity switching of the clock for DVB-C ...
-
Li Yang authored
Add MAINAINERS and CREDITS entry for Freescale Highspeed USB device driver. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Li Yang authored
Update gadget_chip.c, ether.c for newly added Freescale Highspeed USB device driver. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Li Yang authored
Freescale high-speed USB SOC can be found on some Freescale processors among different architectures. It supports both host and device functions. This driver adds its device support for Linux USB Gadget layer. It is tested on MPC8349 and MPC8313, but should work on other platforms with minor tweaks. The driver passed USBCV 1.3 compliance tests. Note that this driver doesn't yet include OTG support. Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jiang Bo <tanya.jiang@freescale.com> Signed-off-by: Bruce Schmid <duck@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Raphael Assenat authored
Here's a patch which adds my device to the list. This patch enables the broken suspend quirk for the PCI OHCI controller present in the IT8152F/G RISC-to-PCI Companion Chip. Signed-off-by: Raphael Assenat <raph@8d.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Eberhard Fahle authored
The driver uses usb_control_msg() for exchanging data with the device. When the driver lived freeley _outside_ the kernel tree (pre 2.6.21) the timeouts for these calls where set to 5*HZ for reading, 1HZ for writing. (These timeouts seemed to work fine for all users of the driver, at least nobody complained in the last 2 years. The current code (2.6.21-rc5) removed the 'HZ' from the timeouts and left the driver with 5 jiffies for reading and 1 jiffy for writing. My new machine is fast, but not that fast. The patch also removes a useless debug statement, which was left over from testing a broken firmware version From: Eberhard Fahle <e.fahle@wayoda.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Hans Engelen authored
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Phil Dibowitz authored
Per the Rui Santos and the hardware manufacturers, this actually inhibits useful parts of the hardware. The correct way to use this hardware is with the software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers are also planning on including Linux drivers/material in future revisions. CC: Rui Santos <rsantos@grupopie.com> CC: <johann.wilhelm@student.tugraz.at> CC: <zihan@huawei.com> CC: <wanganyu1983@huawei.com> CC: <dingjianjian@huawei.com> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Craig Shelley authored
Two new device IDs for CP2101 driver. Signed-off-by: Craig Shelley <craig@microtron.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Joey Goncalves authored
Hi Greg: I have found that /drivers/usb/misc/ldusb.c works with the "PICDEM Full Speed USB" http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en021940Signed-off-by: Joey S Goncalves <jgoncalves@peragrin.com> Cc: Michael Hund <MHund@LD-Didactic.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Oliver Neukum authored
the memory barrier is needed only with smp. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
David Brownell authored
Remove the old crisv10 HCD ... it can't have built for some time, doesn't even have a Kconfig entry, was the last driver not to have been converted to the "hcd" framework, and considering the usbcore changes since its last patch was merged, has just got to buggy as all get-out. I'm told Axis has a new driver, and will be submitting it soon. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Erik Hovland authored
Another workaround for the glitch in the network layer, whereby one call ignores the (otherwise kernel-wide) convention that free() calls should not oops when passed nulls. This code already handles that API glitch in most other paths. From: Erik Hovland <erik@hovland.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch (as903) adds a "busnum" sysfs attribute for USB devices. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Simon Arlott authored
The device has commands to start/stop the ADSL function, so this adds a sysfs attribute to allow it to be started/stopped/restarted. It also stops polling the device for status when the ADSL function is disabled. There are no problems with sending multiple start or stop commands, even with a fast loop of them the device still works. There is no need to protect the restart process from further user actions while it's waiting for 1.5s. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Simon Arlott authored
Detect usb device shutdown and ignore failed urbs. This happens when the driver is unloaded or the device is unplugged. I'm not sure what other urb statuses should be ignored, and the warning message doesn't need to be shown when the module is unloaded or the device is removed. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
S.Caglar Onur authored
Remove duplicate define of OHCI_QUIRK_ZFMICRO from ftdi-elan.c, its already defined in drivers/ush/host/ohci.c Signed-off-by: "S.Caglar Onur" <caglar@pardus.org.tr> Cc: <tony.olech@elandigitalsystems.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Leon Leong authored
Add the detection for the BandRich BandLuxe C100/C100S/C120 HSDPA Data Card. With the vendor and product IDs are set properly, the data card can be detected and works fine. Signed-off-by: Leon Leong <upleong@bandrich.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Wu, Bryan authored
skb_push function may return a pointer which is not aligned as required by struct rndis_packet_msg_type. Using attribute trick to fix this bug. Signed-off-by: Roy Huang <roy.huang@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-