- 18 May, 2007 9 commits
-
-
Eugene Surovegin authored
Original patch is from Jeff Haran <jharan@brocade.com> with my minor style fixes. His comments follow: The first problem was in the function that configures the PHY for autonegotiation, genmii_setup_aneg(). The original code does a read/modify/write of the autonegotiation advertizement register (reg 4), followed by a read/modify/write of the control register (reg 0). While the original code follows the proper procedure as per reading the IEEE specs, what I found is that on at least one PHY model (National DP83843) the read of the control register comes back with the soft reset bit set (bit 15). Because of the read/modify/write operation, this causes the write to write a 1 back to the reset bit, which initiates a software reset of the PHY. This software reset causes the PHY to return to its power up state which advertizes all modes of operation, thus negating the write to the autoneg advertizement register. The modification is to spin reading the control register until the soft reset bit is clear before doing the modify/write. The second problem was in the function that configures the PHY for forced operation, genmii_setup_forced(). The original code initiates a software reset operation via a write of a 1 to bit 15 of the control register (reg 0), but then proceeds to do a second write to that same register without waiting until that reset bit is cleared by the PHY itself (which according to the IEEE specs indicates that the PHY reset is complete). This is a violation of how one is supposed to use this software reset feature of these PHYs and I believe was the cause of mysterious, difficult to reproduce link failures that we've observed on some of our systems that use this driver. The fix is to modify the function so that it spins waiting for the reset bit to clear after doing the soft reset and before doing the subsequent write. Signed-off-by:
Jeff Haran <jharan@brocade.com> CC: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Eugene Surovegin <ebs@ebshome.net> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Eugene Surovegin authored
Fix "Section mismatch" warnings Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Stephen Hemminger authored
Do some memory barrier changes for safety/perfomance: Don't need read after update to index, mmiowb() followed by read at end of irq is sufficient. Signed-off-by:
Stephn Hemminger <shemminger@linux-foundation.org> Signed-off-by:
-
Stephen Hemminger authored
This workaround was added to deal with NAPI core and how it affected dual port shared polling. It turned out not to be necessary. Stopping device 0 only doesn't stop NAPI from working completely after that. Signed-off-by:
-
Stephen Hemminger authored
Make sure that if we ever get a MIB counter overflow interrupt (normally masked off), that the IRQ is cleared. Signed-off-by:
-
Stephen Hemminger authored
When driver can't allocate receive buffer it drops incoming packet. Keep a counter. Signed-off-by:
-
Stephen Hemminger authored
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3) driver. The PHY register settings are mostly black magic, even with access to the documentation it isn't clear what the right values are. The changes are mostly comments, the code change only affects the Yukon FE (100 mbit only) version. Signed-off-by:
-
Stephen Hemminger authored
The problems with Gigabyte motherboards are system configuration dependent. Since it works fine for some users, it doesn't make sense to deprive them. Signed-off-by:
-
- 17 May, 2007 31 commits
-
-
David Woodhouse authored
The function ipxrtr_route_packet() takes a 'len' argument of type size_t. However, its prototype in af_ipx.c incorrectly suggests that the corresponding argument is of type 'int' instead. Discovered by building with --combine and letting the compiler see it all at once. Signed-off-by:
David Woodhouse <dwmw2@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
David Woodhouse authored
After a suspend/resume cycle, the UART may have been reset into low-speed mode -- either because it's actually been reset, or because the firmware pokes at the old-style divisor registers. If we detected it as a NS16550A SuperIO chip in the first place and set baud_base to 921600, then we should do so again in the resume path. This patch adds that code to serial8250_resume_port(), and also makes serial8250_resume() actually call serial8250_resume_port() for each port instead of just calling uart_resume_port() directly. And thus fixes serial port operation after suspend/resume. It also fixes a bogus comment where we write the EXCR2 register with a comment saying /* EXCR1 */ Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Nick Piggin authored
Re-introduce rmap verification patches that Hugh removed when he removed PG_map_lock. PG_map_lock actually isn't needed to synchronise access to anonymous pages, because PG_locked and PTL together already do. These checks were important in discovering and fixing a rare rmap corruption in SLES9. Signed-off-by:
Nick Piggin <npiggin@suse.de> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Christoph Lameter authored
grow_dev_page() simply passes GFP_NOFS to find_or_create_page. This means the allocation of radix tree nodes is done with GFP_NOFS and the allocation of a new page is done using GFP_NOFS. The mapping has a flags field that contains the necessary allocation flags for the page cache allocation. These need to be consulted in order to get DMA and HIGHMEM allocations etc right. And yes a blockdev could be allowing Highmem allocations if its a ramdisk. Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by:
Christoph Lameter <clameter@sgi.com> Signed-off-by:
-
Rafael J. Wysocki authored
The sysfs files /sys/power/disk and /sys/power/state do not work as documented, since they allow the user to write only a few initial characters of the input string to trigger the option (eg. 'echo pl > /sys/power/disk' activates the platform mode of hibernation). Fix it. Special thanks to Peter Moulder <Peter.Moulder@infotech.monash.edu.au> for pointing out the problem. Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl> Acked-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Jan Kara authored
i_mutex on quota files is special. Unlike i_mutexes for other inodes it is acquired under dqonoff_mutex. Tell lockdep about this lock ranking. Also comment and code in quota_sync_sb() seem to be bogus (as i_mutex for quota file can be acquired under dqonoff_mutex). Move truncate_inode_pages() call under dqonoff_mutex and save some problems with races... Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Hugh Dickins authored
No other architecture calls check_pgt_cache() from within flush_tlb_mm(), and i386 is already calling check_pgt_cache() from the usual places, tlb_finish_mmu() and cpu_idle() (the latter being odd, but not unusual). flush_tlb_mm() has no business to be freeing pages: remove that line, which sneaked in with slub's i386 support. Signed-off-by:
Hugh Dickins <hugh@veritas.com> Cc: Andi Kleen <ak@suse.de> Acked-by:
William Lee Irwin III <wli@holomorphy.com> Cc: David Miller <davem@davemloft.net> Signed-off-by:
-
Nate Diller authored
Use zero_user_page() instead of open-coding it. Signed-off-by:
Nate Diller <nate.diller@gmail.com> Cc: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by:
-
Dan Aloni authored
Make sysctl/kernel/core_pattern and fs/exec.c agree on maximum core filename size and change it to 128, so that extensive patterns such as '/local/cores/%e-%h-%s-%t-%p.core' won't result in truncated filename generation. Signed-off-by:
Dan Aloni <da-x@monatomic.org> Signed-off-by:
-
wendy xiong authored
This patch add new sub-device-id to support new adapter and changed the interrupt irq number for unsigned char to unsigned int. [akpm@osdl.org: fix whitespace in device table] Signed-off by: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by:
-
David Brownell authored
Make drivers/rtc/Kconfig be clearer about what the various "interfaces" actually mean, by showing path names. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
David Brownell authored
Fix typo which breaks build. How did that happen? Signed-off-by:
-
David Brownell authored
Loosen gpio_{request,free}() and gpio_direction_{in,out}put() call context restrictions slightly, so a common idiom is no longer an error: board init code setting up spinlock-safe GPIOs before tasking is enabled. The issue was caught by some paranoid code with might_sleep() checks. The legacy platform-specific GPIO interfaces stick to spinlock-safe GPIOs, so this change reflects current implementations and won't break anything. Signed-off-by: -
Randy Dunlap authored
Andi Kleen pointed out to me that the kernel locking cheat sheet table entries are unreadable. Make table entries smaller so that pdf and ps output is readable (columns were being overwritten and garbled) by using abbreviations. This allows the tables to fit on one page cleanly. Add a Legend for the abbreviations: SLIS: spin_lock_irqsave SLI: spin_lock_irq SL: spin_lock SLBH: spin_lock_bh DI: down_interruptible Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Randy Dunlap authored
linux-parport is subscribers-only: Your mail to 'Linux-parport' with the subject Re: [QUESTION] parallel console configuration Is being held until the list moderator can review it for approval. The reason it is being held: Post by non-member to a members-only list Signed-off-by: -
Oleg Nesterov authored
It is a known fact that freezeable multithreaded workqueues doesn't like CPU_DEAD. We keep them only for the incoming CPU-hotplug rework. Sadly, we can't just kill create_freezeable_workqueue() right now, make them singlethread. Signed-off-by:
Oleg Nesterov <oleg@tv-sign.ru> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Gautham R Shenoy <ego@in.ibm.com> Signed-off-by:
-
Gerd Hoffmann authored
Refine SCREEN_INFO sanity check for vgacon initialization. Checking video mode field only to see whenever SCREEN_INFO is initialized is not enougth, in some cases it is zero although a vga card is present. Lets additionally check cols and lines. Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Andi Kleen <ak@suse.de> Cc: Alan <alan@lxorguk.ukuu.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Acked-by:
Eric W. Biederman <ebiederm@xmission.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by:
-
Heiko Carstens authored
All architectures that have an implementation of smp_call_function_single let it return -EBUSY if it is asked to execute func on the current cpu. (akpm: except for x86_64). Therefore the UP version must always return -EBUSY. [akpm@linux-foundation.org: build fix] Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by:
-
Heiko Carstens authored
Just thought this is easier to read. Acked-by:
Davide Libenzi <davidel@xmailserver.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
__vunmap doesn't seem to be used outside of mm/vmalloc.c, and has no prototype in any header so let's make it static Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Bernhard Walle authored
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text:mtrr_bp_init from .text between 'id entify_cpu' (at offset 0x6571) and 'IRQ0x20_interrupt' It's because identify_cpu() which is __cpuinit calls mtrr_bp_init() which is __init(). __cpuinit() expands to nothing if CONFIG_HOTPLUG_CPU=y and so the call is illegal. Signed-off-by:
Bernhard Walle <bwalle@suse.de> Cc: Andi Kleen <ak@suse.de> Signed-off-by:
-
Aaron Durbin authored
Strip __cpuinit[data] from Node <-> PXM routines and supporting data structures. Also make pxm_to_node_map and node_to_pxm_map local to the numa acpi module. This fixes a bug triggered by the following conditions: - boot on a machine with a SLIT table defined - kernel is configured w/ CONFIG_HOTPLUG_CPU=n - cat /sys/devices/system/node/node*/distance This will cause an oops by calling into a freed memory section. In particular, on x86_64, __node_distance calls node_to_pxm(). Signed-off-by:
Aaron Durbin <adurbin@google.com> Cc: Len Brown <lenb@kernel.org> Cc: <stable@kernel.org> Signed-off-by:
-
Christoph Lameter authored
Currently we have a maze of configuration variables that determine the maximum slab size. Worst of all it seems to vary between SLAB and SLUB. So define a common maximum size for kmalloc. For conveniences sake we use the maximum size ever supported which is 32 MB. We limit the maximum size to a lower limit if MAX_ORDER does not allow such large allocations. For many architectures this patch will have the effect of adding large kmalloc sizes. x86_64 adds 5 new kmalloc sizes. So a small amount of memory will be needed for these caches (contemporary SLAB has dynamically sizeable node and cpu structure so the waste is less than in the past) Most architectures will then be able to allocate object with sizes up to MAX_ORDER. We have had repeated breakage (in fact whenever we doubled the number of supported processors) on IA64 because one or the other struct grew beyond what the slab allocators supported. This will avoid future issues and f.e. avoid fixes for 2k and 4k cpu support. CONFIG_LARGE_ALLOCS is no longer necessary so drop it. It fixes sparc64 with SLAB. Signed-off-by:
"David S. Miller" <davem@davemloft.net> Signed-off-by:
-
Christoph Lameter authored
Consolidate functionality into the #ifdef section. Extract tracing into one subroutine. Move object debug processing into the #ifdef section so that the code in __slab_alloc and __slab_free becomes minimal. Reduce number of functions we need to provide stubs for in the !SLUB_DEBUG case. Signed-off-by:
-
Christoph Lameter authored
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it. Signed-off-by:
-
Christoph Lameter authored
The atomicity when handling flags in SLUB is not necessary since both flags used by SLUB are not updated in a racy way. Flag updates are either done during slab creation or destruction or under slab_lock. Some of these flags do not have the non atomic variants that we need. So define our own. Signed-off-by:
-
Christoph Lameter authored
Align the output of % with K/M/G of sizes. Check for empty NUMA information to avoid segfault on !NUMA. -r should work directly not only if we match a single slab without additional options. Signed-off-by:
-
Andrew Morton authored
I'm getting zillions of undefined references to __kmalloc_size_too_large on alpha. For some reason alpha is building out-of-line copies of kmalloc_slab() into lots of compilation units. It turns out that gcc just isn't smart enough to work out that __builtin_contant_p(size)==true implies that __builtin_contant_p(index)==true. So let's give it a bit of help. Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by:
-
Christoph Lameter authored
slub warns on this, and we're working on making kmalloc(0) return NULL. Let's make slab warn as well so our testers detect such callers more rapidly. Signed-off-by:
-
Christoph Lameter authored
Use inline functions to access the per cpu bit. Intoduce the notion of "freezing" a slab to make things more understandable. Signed-off-by:
-
Christoph Lameter authored
Two definitions remained in slab.h that are particular to the SLAB allocator. Move to slab_def.h Signed-off-by:
-
