- Apply Pavel Macheks suspend resume double resume fix.

- Finally remove the busy field for ata_operations and replace it with
   MOD_INC_USE_COUNT and MOD_DEC_USE_COUNT.

- Fix ali15xx chipset support by removing initialization differences,
   apparently caused by mislead interpretation of the specs or a mismatch
   between the specification and reality.

- Guard calls to ide_set_handler with checks to see whatever the previously
   installed IRQ handler already served it's purpose.

- Convert timeout checks on poll_timeout to the time_before() interface.

- Consolidate the two different IRQ handlers for multi mode PIO writes into
   one. The problems remain the same but at least now we will only have to
   tangle one single problem.

- Make for less terse error messages in ide-tape.c.

- Replaced all timecomparisions done by hand with all the proper timer_after()
   commands.

- Remove the drive niec1 mechanisms alltogether. There are several reasons for
   this:

   1. The code implementing it is nonintelliglible and therefore propably
   broken.

   2. If we have to invent somethig about sceduling drive IO, it should be done
   on the BIO level.

   3. We may in fact interleave with the IO sceduling on the upper layers and
   the results of two overlapping signal filters overlapped with each other can
   be disasterous to the overall throughput. (In fact they *are* most of the
   time.)

   4. It was not working if you had intermixed modes on different drives
   DMA versus PIO.

   5. Our goal is to have a driver which is able to share the badwidth
   properly and shouldn't needing this kind of "tuning".

- Remove unused nice2 from disk struct.

- Rename channel member of ata_channel to unit and device to dev to
   just prevent wrong interpretations. This prevents constructs like
   channel->channel...

- Mark all members of structures, which get jiffies assigned or involved in
   ugly timeout calculations with the prefix PADAM_  for easy spotting. This is
   Polish for "I'm falling down" or "This brings me to the knees" or slag
   comment for "What a sh..". Please be assured that it doesn't sound vulgar.

   Please grep for it to see immediately why this nomenclature is justified.

- Rename hwifs_s to ata_channel and eliminate ide_hwifs_t as well as the HWIF
   macro. OK this step makes this patch rather big.

- Replace the task_io_reg_t with the simple u8. There is no need to obfuscate
   the code more then necessary.

- kill some unnecessary type definitions out from hdreg.h.

- Add proper attributes to register files in hdreg.h.

- Don't use raw arrays for tfRegister and hobRegister in ide_task_s.  Use out
   nice global structures describing the fields in them.  This allows to kill
   the following defines:

     IDE_DATA_OFFSET
     IDE_FEATURE_OFFSET
     IDE_NSECTOR_OFFSET
     IDE_SECTOR_OFFSET
     IDE_LCYL_OFFSET
     IDE_HCYL_OFFSET
     IDE_SELECT_OFFSET
     IDE_COMMAND_OFFSET

   and many many others.

- Please have a look at the following in pdc4030.c. It couldn't have worked!
   This has been fixed in one go with the above change:

   memcpy(args.hobRegister, NULL, sizeof(struct hd_drive_hob_hdr));

- Kill the redundant *_REG_HOB definitions. They don't help readability in any
   way.

- Push BAD_DMA_DRIVE and GOOD_DMA_DRIVE to the ide-pmac.c file, since this is
   the only place where those get used.

- Kill unused fields from the ide_task_s structure. In esp. we pass a task
   attached to a request and not the other way around!

- Rename hwif field to channel in struct ide_drive_s.

- Move the request queue to the level where proper serialization has to happen
   anyway - the channel structure.

- Support for additional Promise controller id's (PDC20276).

- Remove code duplication between do_rw_taskfile and do_taskfile.
   This will evolve into a more reasonable ata_command() function
   finally. The ata_taskfile function has far too many arguments, but
   I favour this over having two different code paths for getting
   actual data to the drive.

Fix initrd problem that appeared back in 2.5.2-pre6 when kdev_t type
changed and comparison function was incorrectly converted..

This patch remove unused variable/function/define, and small indent
cleanup.

The following patch moves MSDOS_SB() and MSDOS_I() into #define
__KERNEL__.

- Apply more patches from Vojtech Pavlik for the handling of host chip setup.
   Hopefully they are settled now.

- Kill unused CONFIG_BLK_DEV_MODES

- Push register addressing down in to task_vlb_sync.

- Make the taskfile parsing stuff actually readable. This is compressing the
   code by an incredible amount. We use just one function doing the whole
   scanning right now. This should make sure that the IRQ handler used by a
   particular command is always right.  I didn't introduce typos hopefully
   here.

- Don't call ide_handler_parser as argument for do_taskfile() any longer. We
   have killed this function by coalescing it's functionality with
   ide_cmd_type_parser() anyway.

- Kill unused SLC90E66 code, which Vojtech apparently missed in his patch.

- sync up with 2.5.7-pre2

Once again the actual patch is rather big mostly due to the removal of
some default configuration variables which are not used anylonger. So time for
the next patch stage.

- add joystick support for CS46xx driver
- Audigy code updates
- fix sound/core/Config.in (wrong dep_tristate usage)
- rawmidi interface fixes (memory leak)
- chang spinlock to rwlock in pcm_native.c (streams linking)
- further fixes of dependencies in Makefiles
- remove experimental time-sync support from sequencer
- fix/update for 32-bit -> 64-bit ioctl converter code
- wavefront driver cleanups
- CMIPCI driver updates
- update joystick support in CS4281
- add detection (not support) of M Audio Delta1010LT
- add AMD768 PCI ID to intel8x0 driver
- add joystick code to trident driver
- remove static variable initialization to zero

This adds initial driverfs support to ISAPNP driver.  It was approved by
the ISAPNP maintainer (Jaroslav Kysela).

Seperates affs_sb_info from struct super_block.

Seperates hfs_sb_info from struct super_block.

Seperates shmem_sb_info from struct super_block.

	file_system_typer-related code moved from fs/super.c to
fs/filesystems.c

into home.transmeta.com:/home/torvalds/v2.5/linux

Seperates udf_sb_info from struct super_block.

Seperates isofs_sb_info from struct super_block.

I got burnt one too many time by mismatches between
the pci_pool and "real" slabs... something changed in
mm/slab.c and broke a driver, so I'm going for the real
fix this time.  Having poisoning that _works_ is a huge
help in the innards of the USB host controller drivers.

This patch gets rid of some #ifdefs and makes the pci_pool
code poison memory if CONFIG_DEBUG_SLAB is set.
The functionality has always been there, but this makes
it simpler to get at.

into home.transmeta.com:/home/torvalds/v2.5/linux

exiting heathrow_modem_enable() with a lock held.

SI_DETHREAD, plus a couple of minor fixes.

into home.transmeta.com:/home/torvalds/v2.5/linux

Remove remnants of zlib_fs.

Remove FS_REQUIRES_DEV from JFFS2. We never really used the block device anyway.

From Arnaldo Carvalho de Melo.

added NEC printer to quirks list

  
Workaround for the ATEN switches

Several functions in the serial drivers can be called from bottom
half or interrupt context. They must use the GFP_ATOMIC flag for
calls to kmalloc() and usb_submit_urb().
  
Functions which must use GFP_ATOMIC:
1. All *_callback() functions.
2. Any code which is inside a spinlock.
3. write(), throttle(), unthrottle(), which may be called by
   the line discipline in bottom half context.
  
Functions which can use GFP_KERNEL:
1. open(), close(), startup(), shutdown(), set_termios().

  
Here is a patch to add support for F5U011 to catc.c driver. The
patch has been compile tested against 2.5.6 and 2.5.7pre1
(and tested against 2.5.5-dj1) and should apply cleanly.

  I've written a patch Vojtech and I discussed for enhancing the
hiddev code to optionally provide more detailed output on read().
The old functionality is still supported by default, and in
situations where HID usage codes are unique across reports, the
old method is still preferable due to its terseness.
    
  The new method provides the ability to determine exactly which
value has changed, in cases where the HID usage codes are not  
unique.  It also provides a means to optionally receive notification
when input reports are received from the device, whether or not
any of the values in the report have changed.

  The details of the changes are as follows:
  
  - All current code behaves identically

  - A new ioctl pair HIDIOCGFLAG/HIDIOCSFLAG gets and clears
    flags on the hiddev device.                             

  - If you set the flag HIDDEV_FLAG_UREF, the read() call switches
    from reading hiddev_event structures to hiddev_usage_ref
    structures.  The change takes effect immediately, even to
    already queued events that haven't been read() yet.  Here's
    an example of enabling FLAG_UREF:                          

    {
        int flag = HIDDEV_FLAG_UREF;
        if (ioctl(fd, HIDIOCSFLAG, &flag) != 0) {
                perror("ioctl");
                exit(1);
        }
    }
  
  - With the HIDDEV_FLAG_REPORT set (which is only allowed if
    HIDDEV_FLAG_UREF is also set), there is a special uref that
    will be read() in addition to the ones corresponding to
    changes in the device state: when uref.field_index is set to
    HID_FIELD_INDEX_NONE, this uref is a notification that the
    report referred to by report_type and report_id has been
    received from the device.  This can be useful in situations
    when the notification of the arrival of a report is useful
    even if there is no change in state.

- bind to 7/1/2 alternate setting by default, to fix printing with HP
  LaserJet 1200 and 2200
- ioctls needed by the GPL user-mode IEEE 1284.4 driver which is part of
  the HP OfficeJet Linux driver (http://hpoj.sourceforge.net):
  - dynamic switching between 7/1/[123] alternate settings
  - sending HP vendor-specific channel-change-request to support
    memory card readers on HP PhotoSmart printers
  - inquire more information about the peripheral, including
    /proc/bus/usb/xx/yy linkage to get even more information
- fix apparent array overflow (by 1 entry) in usblp_probe when more than
  the maximum number of USB printers are connected
- for the 2.2 version, added MODULE_{INC,DEC}_USE_COUNT to prevent rmmoding
  of printer.o (and subsequent OOPSes) while a USB printer device is open
- cleaned up the code in a few places by consolidating duplicated code

into home.transmeta.com:/home/torvalds/v2.5/linux

into home.transmeta.com:/home/torvalds/v2.5/linux