To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>

Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>

Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.

With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
 - ICE_DDP_PKG_SUCCESS
 - ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
 - ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.

One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).

We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.

Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Since the capability of a PTYPE within a specific package could be
negotiated by checking the HW bit map, it means that there's no need
to maintain a different PTYPE list for each type of the package when
parsing PTYPE. So refactor the PTYPE validating mechanism.
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Scan the 'Marker Ptype TCAM' section to retrieve the Rx parser PTYPE
enable information from the current package.
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

IBMVNIC_STATS_TIMEOUT and IBMVNIC_INIT_FAILED are not used in the driver.
Remove them.
Suggested-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update return codes to be more informative.
Signed-off-by: Jacob Root <otis@otisroot.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 13510fef.

Causes build warnings.
Signed-off-by: David S. Miller <davem@davemloft.net>

Use min() in order to make code cleaner. Issue found by coccinelle.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
DSA tagger-owned storage fixups

It seems that the DSA tagger-owned storage changes were insufficiently
tested and do not work in all cases. Specifically, the NXP Bluebox 3
(arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts) got broken by
these changes, because
(a) I forgot that DSA_TAG_PROTO_SJA1110 exists and differs from
    DSA_TAG_PROTO_SJA1105
(b) the Bluebox 3 uses a DSA switch tree with 2 switches, and the
    tagger-owned storage patches don't cover that use case well, it
    seems

Therefore, I'm sorry to say that there needs to be an API fixup: tagging
protocol drivers will from now on connect to individual switches from a
tree, rather than to the tree as a whole. This is more robust against
various ordering constraints in the DSA probe and teardown paths, and is
also symmetrical with the connection API exposed to the switch drivers
themselves, which is also per switch.

With these changes, the Bluebox 3 also works fine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On the NXP Bluebox 3 board which uses a multi-switch setup with sja1105,
the mechanism through which the tagger connects to the switch tree is
broken, due to improper DSA code design. At the time when tag_ops->connect()
is called in dsa_port_parse_cpu(), DSA hasn't finished "touching" all
the ports, so it doesn't know how large the tree is and how many ports
it has. It has just seen the first CPU port by this time. As a result,
this function will call the tagger's ->connect method too early, and the
tagger will connect only to the first switch from the tree.

This could be perhaps addressed a bit more simply by just moving the
tag_ops->connect(dst) call a bit later (for example in dsa_tree_setup),
but there is already a design inconsistency at present: on the switch
side, the notification is on a per-switch basis, but on the tagger side,
it is on a per-tree basis. Furthermore, the persistent storage itself is
per switch (ds->tagger_data). And the tagger connect and disconnect
procedures (at least the ones that exist currently) could see a fair bit
of simplification if they didn't have to iterate through the switches of
a tree.

To fix the issue, this change transforms tag_ops->connect(dst) into
tag_ops->connect(ds) and moves it somewhere where we already iterate
over all switches of a tree. That is in dsa_switch_setup_tag_protocol(),
which is a good placement because we already have there the connection
call to the switch side of things.

As for the dsa_tree_bind_tag_proto() method (called from the code path
that changes the tag protocol), things are a bit more complicated
because we receive the tree as argument, yet when we unwind on errors,
it would be nice to not call tag_ops->disconnect(ds) where we didn't
previously call tag_ops->connect(ds). We didn't have this problem before
because the tag_ops connection operations passed the entire dst before,
and this is more fine grained now. To solve the error rewind case using
the new API, we have to create yet one more cross-chip notifier for
disconnection, and stay connected with the old tag protocol to all the
switches in the tree until we've succeeded to connect with the new one
as well. So if something fails half way, the whole tree is still
connected to the old tagger. But there may still be leaks if the tagger
fails to connect to the 2nd out of 3 switches in a tree: somebody needs
to tell the tagger to disconnect from the first switch. Nothing comes
for free, and this was previously handled privately by the tagging
protocol driver before, but now we need to emit a disconnect cross-chip
notifier for that, because DSA has to take care of the unwind path. We
assume that the tagging protocol has connected to a switch if it has set
ds->tagger_data to something, otherwise we avoid calling its
disconnection method in the error rewind path.

The rest of the changes are in the tagging protocol drivers, and have to
do with the replacement of dst with ds. The iteration is removed and the
error unwind path is simplified, as mentioned above.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was incorrectly converted assuming that "sja1105" is the only
tagger supported by this driver. This results in SJA1110 switches
failing to probe:

sja1105 spi1.0: Unable to connect to tag protocol "sja1110": -EPROTONOSUPPORT
sja1105: probe of spi1.2 failed with error -93

Add DSA_TAG_PROTO_SJA1110 to the list of supported taggers by the
sja1105 driver. The sja1105_tagger_data structure format is common for
the two tagging protocols.

Fixes: c79e8486 ("net: dsa: tag_sja1105: convert to tagger-owned data")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The method was meant to zeroize ds->tagger_data but got the wrong
pointer. Fix this.

Fixes: c79e8486 ("net: dsa: tag_sja1105: convert to tagger-owned data")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing extacks for common configuration errors.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev can be a NULL here, not all requests set require_dev.

Fixes: e4b89540 ("netlink: add net device refcount tracker to struct ethnl_req_info")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the order of arguments and make qdisc_is_running() appear first.
This is more readable for the general case.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hangbin Liu says:

====================
net: add new hwtstamp flag HWTSTAMP_FLAG_BONDED_PHC_INDEX

This patchset add a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When user want to get bond active interface's PHC, they need to add this flag
and aware the PHC index may changed.

v3: Use bitwise test to check the flags validation
v2: rename the flag to HWTSTAMP_FLAG_BONDED_PHC_INDEX
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is a failover, the PHC index of bond active interface will be
changed. This may break the user space program if the author didn't aware.

By setting this flag, the user should aware that the PHC index get/set
by syscall is not stable. And the user space is able to deal with it.
Without this flag, the kernel will reject the request forwarding to
bonding.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 94dd016a ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 94dd016a ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.

This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.

With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve the build testing of mtk_eth drivers by enabling them when
COMPILE_TEST is selected. Moreover COMPILE_TEST will be useful
for the driver development.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The root-lock is dropped before dev_hard_start_xmit() is invoked and after
setting the __QDISC___STATE_RUNNING bit. If the Qdisc owner is preempted
by another sender/task with a higher priority then this new sender won't
be able to submit packets to the NIC directly instead they will be
enqueued into the Qdisc. The NIC will remain idle until the Qdisc owner
is scheduled again and finishes the job.

By serializing every task on the ->busylock then the task will be
preempted by a sender only after the Qdisc has no owner.

Always serialize on the busylock on PREEMPT_RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code that uses variable queued has been removed,
and "mt76_is_usb(dev) ? q->ndesc - q->queued : q->queued"
didn't do anything, so all they should be removed as well.

Eliminate the following clang warnings:
drivers/net/wireless/mediatek/mt76/debugfs.c:77:9: warning: variable
‘queued’ set but not used.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 2d8be76c ("mt76: debugfs: improve queue node readability")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently "bond_should_notify_peers: slave ..." messages are printed whenever
"bond_should_notify_peers" function is called.

+++
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): Received LACPDU on port 1
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): Rx Machine: Port=1, Last State=6, Curr State=6
Dec 12 12:33:26 node1 kernel: bond0: (slave enp0s25): partner sync=1
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:26 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
...
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): Received LACPDU on port 2
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): Rx Machine: Port=2, Last State=6, Curr State=6
Dec 12 12:33:30 node1 kernel: bond0: (slave enp4s3): partner sync=1
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
Dec 12 12:33:30 node1 kernel: bond0: bond_should_notify_peers: slave enp0s25
+++

This is confusing and can also clutter up debug logs.
Print logs only when the peer notification happens.
Signed-off-by: Suresh Kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dma_addr was declared using DEFINE_DMA_UNMAP_ADDR() which requires to
use dma_unmap_addr() to access it.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 753a026c ("net: ocelot: add FDMA support")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When inserting a SFP that runs at 2.5G, then the Serdes was still
configured to run at 1G. Because the config->speed was 0, and then the
speed of the serdes was not configured at all, it was using the default
value which is 1G. This patch stop calling the serdes function set_speed
and allow the serdes to figure out the speed based on the interface
type.

Fixes: d28d6d2e ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test is currently run on a single host with private addresses,
either over veth or by setting a nic in loopback mode with macvlan.

Support running between two real devices. Allow overriding addresses.

Also cut timeout to fail faster on error and explicitly log success.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefan Wahren says:

====================
add Vertexcom MSE102x support

This patch series adds support for the Vertexcom MSE102x Homeplug GreenPHY
chips [1]. They can be connected either via RGMII, RMII or SPI to a host CPU.
These patches handles only the last one, with an Ethernet over SPI protocol
driver.

The code has been tested only on Raspberry Pi boards, but should work
on other platforms.

Changes in V3:
- drop IF_PORT_HOMEPLUG again, since it's actually not used

Changes in V2:
- improve lock handling for RX & TX path
- add new patch to introduce IF_PORT_HOMEPLUG as suggested by Andrew Lunn
- address all the comments by Jakub Kicinski, Andrew Lunn, Kernel test robot

[1] - http://www.vertexcom.com/p_homeplug_plc_en.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This implements an SPI protocol driver for Vertexcom MSE102x
Homeplug GreenPHY chip.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devicetree binding for the Vertexcom MSE102x Homeplug GreenPHY chip
as SPI device.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add vendor prefix for Vertexcom Technologies, Inc [1].

[1] - http://www.vertexcom.com/Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mvneta provides mac_an_restart and mac_pcs_get_state methods, so needs
to be marked as a legacy driver. Marek spotted that mvneta had stopped
working in 2500base-X mode - thanks for reporting.
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

axienet has a PCS, but does not make use of the phylink PCS support.
Mark it was a pre-March 2020 driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static variables do not need to be initialised to 0, because compiler
will initialise all uninitialised statics to 0. Thus, remove the
unneeded initializations.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the definition of the IPA interconnects for IPA v4.5 so
the path between IPA and system memory is represented by a single
"memory" interconnect.
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first two interconnects defined for IPA on the SDX55 SoC are
really two parts of what should be represented as a single path
between IPA and system memory.

Fix this by combining the "memory-a" and "memory-b" interconnects
into a single "memory" interconnect.
Reported-by: David Heidelberg <david@ixit.cz>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables the "/proc/sys/net/unix/max_dgram_qlen" sysctl to be
exposed to non-init user namespaces. max_dgram_qlen is used as the default
"sk_max_ack_backlog" value for when a unix socket is created.

Currently, when a networking namespace is initialized, its unix sysctls
are exposed only if the user namespace that "owns" it is the init user
namespace. If there is an non-init user namespace that "owns" a networking
namespace (for example, in the case after we call clone() with both
CLONE_NEWUSER and CLONE_NEWNET set), the sysctls are hidden from view
and not configurable.

Exposing the unix sysctl is safe because any changes made to it will be
limited in scope to the networking namespace the non-init user namespace
"owns" and has privileges over (changes won't affect any other net
namespace). There is also no possibility of a non-privileged user namespace
messing up the net namespace sysctls it shares with its parent user namespace.
When a new user namespace is created without unsharing the network namespace
(eg calling clone()  with CLONE_NEWUSER), the new user namespace shares its
parent's network namespace. Write access is protected by the mode set
in the sysctl's ctl_table (and enforced by procfs). Here in the case of
"max_dgram_qlen", 0644 is set; only the user owner has write access.

v1 -> v2:
* Add more detail to commit message, specify the
"/proc/sys/net/unix/max_dgram_qlen" sysctl in commit message.
Signed-off-by: Joanne Koong <joannekoong@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On PREEMPT_RT the seqcount_t for synchronisation is required on 32bit
architectures even on UP because the softirq (and the threaded IRQ handler) can
be preempted.

With the seqcount_t for synchronisation, a reader with higher priority can
preempt the writer and then spin endlessly in read_seqcount_begin() while the
writer can't make progress.

To avoid such a lock up on PREEMPT_RT the writer must disable preemption during
the update. There is no need to disable interrupts because no writer is using
this API in hard-IRQ context on PREEMPT_RT.

Disable preemption on 32bit-RT within the u64_stats write section.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Guillaume Nault says:

====================
bareudp: Remove unused code from header file

Stop exporting unused functions and structures in bareudp.h. The only
piece of bareudp.h that is actually used is netif_is_bareudp(). The
rest can be moved to bareudp.c or even dropped entirely.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This structure is used only in bareudp.c.

While there, adjust include files: we need netdevice.h, not skbuff.h.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>