In a few places the dispc driver needs to know whether the pixel format
is an YUV format. Add a helper to figure that out.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code to calculate offset in dispc's calc_offset() is overly complex.
Simplify it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We have three rotation methods supported by the SoCs with DSS: DMA,
VRFB and TILER.

DMA rotation works in theory on all DSS platforms, but in practice it's
unusable due to the huge amount of memory bandwidth it uses, and has
never really been used.

VRFB is available on OMAP3, but is not supported by omapdrm, even though
we have some code for it in the dispc driver.

TILER is supported on OMAP4/OMAP5/DRA7/AM5 platforms, but has some
driver bugs.

To clean up the driver to help fixing the TILER issues, this patch drops
the DMA and VRFB rotation support, leaving only TILER rotation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Use dev_err_ratelimited() when an OCP error happens, to slightly easen
the flood.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

DSS IP versions 2 and 3 support CLUT modes (color lookup table), but the
driver has never supported those. We still have had some code for CLUT
modes. As the newer DSS IP versions have dropped CLUT support, we might
as well clean up the driver by removing the CLUT related code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The code that sets and clears DOUBLESTRIDE is only ran when using NV12.
This is not correct, as we might first set the bith when using NV12, but
never clear it when using other formats.

Fix it so that when the bit is available (when the HW supports NV12) we
always either set or clear the bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The omap_dss_find_output() function is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Structs omap_overlay and omap_overlay_manager are not used, remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove unused fields in struct omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

get_resolution is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

get_dimensions function pointer is not used, remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The RFBI driver has not worked nor compiled for many years. There are
very few boards out there that use RFBI, and no one has stepped up to
fix it.

So let's remove the RFBI code that doesn't even compile.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove DPI's legacy data_lines code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

recommended_bpp hasn't been used for ages, remove the code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Remove extra includes related to non-DT boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Non-DT booting is no longer supported, so remove legacy code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Define compat_ioctl in omapdriver_fops to make it possible to use 32bit
apps on 64bit platform.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Fix a few type issues that cause compile warnings on 64 bit ARM
compiler. The change should not affect 32bit platforms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We only use read_irqenable() to flush posted write. Instead of having a
separate function for this, do the flush implicitly in write_irqenable().
Thus we can remove read_irqenable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

At the moment we have ovl_set_channel_out() to configure the output
channel of an overlay. It makes sense to have this configuration as part
of the rest of overlay configuration, and in DSS6+ we need the output
channel when doing the other overlay configuration.

This patch adds a 'channel' parameter to ovl_setup(), so that all
overlay configuration is done via the same function, and removes the
ovl_set_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

ovl_enabled() is not used anywhere, so remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

We have been using DRM_MODE_CONNECTOR_Unknown for many of our outputs
because there has not been a proper connector type for them.

We now have connector type for DPI so let's take it into use. At the
same time, add better connector types for the remaining outputs too.

This patch sets the following outputs to use the following connector
types:

DPI -> DPI
DBI -> DPI (MIPI DBI is very similar to DPI at the bus level)
SDI -> LVDS (SDI, TI Flatlink 3G, is a type of LVDS)
VENC -> SVIDEO or Composite
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The SDI platform driver was used for non-DT platforms only. On DT
platforms the SDI port is handled manually. As OMAP display devices are
now instantiated from DT only, remove the SDI platform driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The DPI platform driver was used for non-DT platforms only. On DT
platforms the DPI port is handled manually. As OMAP display devices are
now instantiated from DT only, remove the DPI platform driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The omapdrm exposes the SoC version to userspace through an integer that
contains the OMAP model (e.g. 0x3430 for the OMAP3430). This is an
unfortunate choice of userspace API as it's both conceptually wrong
(userspace nowadays should use /sys/bus/soc/ for that purpose) and
inaccurate as many models with different features are reported with the
same version number.

The only known user of this API is the xomap X11 driver. Even if it has
been deprecated for some time we can't drop the kernel API yet. We can,
however, infer the version number from the SoC family to avoid the need
to pass the version number through platform data.

Do this, which makes the omapdrm platform data not needed anymore, and
ready to be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The default display name is both unused and never set by platform data.
Remove default display name module parameter, platform data field and
runtime infrastructure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The dss_get_core_pdev() function is unused, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

All OMAP platforms use DT nowadays, drop support for non-DT devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The devm_ioremap_resource() call can handle being given a NULL resource,
and prints an error message when mapping fails. Switch the remaining
devm_ioremap() calls to devm_ioremap_resource() and remove all
extraneous resource NULL checks and error messages printed manually by
the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

To ensure that neither the GEM object nor the DRM device goes away while
a GEM object exported through dma-buf is still accessible, references
must be taken to both the GEM object and the DRM device at export time.
The dma-buf release handler already releases the GEM object, but the
export handler doesn't take a corresponding reference, which results in
a refcount underflow.

Fix this by replacing the custom implementation by
drm_gem_dmabuf_export() and drm_gem_dmabuf_release() that handle
reference counting for us.

Fixes: 6ad11bc3 ("staging: drm/omap: dmabuf/prime support")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The display engine only reads from memory, there's no need to use
bidirectional DMA mappings. Use DMA_TO_DEVICE instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Both coherent (uncached) and non-coherent (cached) buffers can have
their pages mapped to the device through the DMA mapping API. Make sure
to unmap any mapped page when freeing a buffer, regardless of its type.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The is_cache_coherent() function currently returns true when the mapping
is not cache-coherent. This isn't a bug as such as the callers interpret
cache-coherent as meaning that the driver has to handle the coherency
manually, but it is nonetheless very confusing. Fix it and add a bit
more documentation to explain how cached buffers are handled.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The omap_gem_cpu_sync() function operates at a page level, while the
omap_gem_dma_sync() function operates at a buffer level. Rename them to
omap_gem_cpu_sync_page() and omap_gem_dma_sync_buffer() respectively to
avoid confusion.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The field contains DMA addresses, clarify that by renaming it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This makes the function more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>