- 19 Jul, 2017 14 commits
-
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by:Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Check for vb2_ops structures that are only stored in the ops field of a vb2_queue structure. That field is declared const, so vb2_ops structures that have this property can be declared as const also. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct vb2_ops i@p = { ... }; @ok@ identifier r.i; struct vb2_queue e; position p; @@ e.ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct vb2_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct vb2_ops i = { ... }; Signed-off-by: -
Gustavo A. R. Silva authored
Remove unnecessary static on local variable t_params. Such variable is initialized before being used, on every execution path throughout the function. The static has no benefit and, removing it reduces the code size. This issue was detected using Coccinelle and the following semantic patch: @bad exists@ position p; identifier x; type T; @@ static T x@p; ... x = <+...x...+> @@ identifier x; expression e; type T; position p != bad.p; @@ -static T x@p; ... when != x when strict ?x = e; In the following log you can see the difference in the code size. Also, there is a significant difference in the bss segment. This log is the output of the size command, before and after the code change: before: text data bss dec hex filename 23314 3640 832 27786 6c8a drivers/media/tuners/tuner-simple.o after: text data bss dec hex filename 23257 3552 768 27577 6bb9 drivers/media/tuners/tuner-simple.o Signed-off-by: -
Colin Ian King authored
Trivial fix to spelling mistake in v4l2_dbg debug message Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
Trivial fix to spelling mistake in v4l2_info message Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 5238 112 4 5354 14ea drivers/media/v4l2-core/videobuf2-dma-sg.o File size After adding 'const': text data bss dec hex filename 5358 0 4 5362 14f2 drivers/media/v4l2-core/videobuf2-dma-sg.o Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Acked-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 3171 192 0 3363 d23 drivers/media/v4l2-core/videobuf2-vmalloc.o File size After adding 'const': text data bss dec hex filename 3291 80 0 3371 d2b drivers/media/v4l2-core/videobuf2-vmalloc.o Signed-off-by:
-
Arvind Yadav authored
dma_buf_ops are not supposed to change at runtime. All functions working with dma_buf_ops provided by <linux/dma-buf.h> work with const dma_buf_ops. So mark the non-const structs as const. File size before: text data bss dec hex filename 6035 272 0 6307 18a3 drivers/media/v4l2-core/videobuf2-dma-contig.o File size After adding 'const': text data bss dec hex filename 6155 160 0 6315 18ab drivers/media/v4l2-core/videobuf2-dma-contig.o Signed-off-by:
-
Bhumika Goyal authored
Declare v4l2_file_operations structure as const as it is only stored in the fops field of video_device structure. This field is of type const, so declare v4l2_file_operations structures with similar properties as const. Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Signed-off-by:
-
Bhumika Goyal authored
Declare v4l2_file_operations structures as const as they are only stored in the fops field of video_device structures. This field is of type const, so declare v4l2_file_operations structures with similar properties as const. Cross compiled bfin_capture.o for blackfin arch. vpbe_display.o file did not cross compile for arm. Could not find any architecture matching the configuraion symbol for fsl-viu.c file. Signed-off-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
/devel/v4l/patchwork/Documentation/media/kapi/cec-core.rst:369: WARNING: Title underline too short. CEC Notifier framework ----------------- Signed-off-by:
-
- 18 Jul, 2017 21 commits
-
-
Hans Verkuil authored
The CEC adapter name used by the pulse8-cec and rainshadow-cec USB device drivers was a fixed string, but it should be unique if you connect multiple of these devices to the same computer. Use dev_name(&serio->dev) instead, which make it unique again. Signed-off-by:
-
Hans Verkuil authored
Especially the '0.10' version number is confusing since CEC_ADAP_G_CAPS returns a completely different version number. Signed-off-by:
-
Hans Verkuil authored
The cec_register_cec_notifier function was in media/cec.h, but it has to be in cec-notifier.h. While we are at it, also document it and add a stub function for when the notifier is disabled or the CEC core code is unreachable. Based on an earlier patch from Jose Abreu <Jose.Abreu@synopsys.com>. Signed-off-by:
-
Hans Verkuil authored
Document the persistent_config module option. Signed-off-by:
-
Hans Verkuil authored
Some hardware does more than one attempt. So when it calls cec_transmit_done when an error occurred it will e.g. use an error count of 2 instead of 1. The framework always assumed a single attempt, but now it is smarter and will sum the counters to detect how many attempts were made. Signed-off-by:
-
Hans Verkuil authored
Include the CEC pin framework documentation by reading cec-pin.h. Include the CEC notifier framework documentation by reading cec-notifier.h. Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Hans Verkuil authored
Add support for CEC hardware that relies on low-level pin polling or GPIO interrupts. One example is the Allwinner SoC. But any GPIO-based CEC implementation can use this as well. A GPIO implementation is very suitable as well for debugging: it can use interrupts to detect state changes and report it. Userspace can then verify if the bus traffic is correct. This also makes error injection possible. The disadvantage is that it is hard to get the timings right since linux isn't a hard realtime system. In general on an idle system it works quite well, but under load the timer will miss its mark every so often. The debugfs file /sys/kernel/debug/cec/cecX/status gives some statistics with respect to the timer overruns. When the adapter is unconfigured and the low-level driver supports interrupts, then the interrupt will be used to detect changes. This should be quite accurate. But when the adapter is configured a hrtimer has to be used. The hrtimer implements a state machine where for each state the code will read the bus or drive the bus and go on to the next state. It will re-arm the timer with a delay based on the next state. Signed-off-by:
-
Hans Verkuil authored
Add support for the new MONITOR_PIN mode. Add the cec_pin_event function that the CEC pin code will call to queue pin change events. Signed-off-by:
-
Hans Verkuil authored
Document CEC_CAP_MONITOR_PIN, CEC_EVENT_PIN_LOW/HIGH, CEC_EVENT_FL_DROPPED_EVENTS and CEC_MODE_MONITOR_PIN. Signed-off-by:
-
Hans Verkuil authored
Event handling was always fairly simplistic since there were only two events. With the addition of pin events this needed to be redesigned. The state_change and lost_msgs events are now core events with the guarantee that the last state is always available. The new pin events are a queue of events (up to 64 for each event) and the oldest event will be dropped if the application cannot keep up. Lost events are marked with a new event flag. Signed-off-by:
-
Hans Verkuil authored
Add support for low-level CEC pin monitoring. This adds a new monitor mode, a new capability and two new events. Signed-off-by:
-
Hans Verkuil authored
Document what this callback does. Signed-off-by:
-
Hans Verkuil authored
This is needed for CEC adapters that allocate resources that have to be freed before the cec_adapter is deleted. Signed-off-by:
-
Hans Verkuil authored
Currently the transmit_(attempt_)done and received_msg functions set the timestamp themselves. For the upcoming low-level pin API we need to pass this as an argument instead. So make _ts variants that allow the caller to specify the timestamp. Signed-off-by:
-
Hans Verkuil authored
Kernel logging messes up the upcoming low-level CEC monitoring support which is very time-sensitive. So change the debug level of this message but keep a counter that is shown in the debugfs status log. Signed-off-by:
-
Hans Verkuil authored
The transmit code would increase the sequence number first thing, even though CEC_TRANSMIT would return an error due to a malformatted cec_msg struct later on. While valid behavior, this had the disadvantage of producing holes in the sequence list that made debugging harder. Only increase the sequence number when the whole message is validated. When debugging (i.e. with cec-ctl -M) the sequence numbering is now nicely increasing by 1 per message. Signed-off-by:
-
Hans Verkuil authored
The CEC version, vendor ID and OSD name were not cleared when clearing the current set of logical addresses. This was unexpected and somewhat confusing, so reset all these fields to their default values. Also document this since the documentation wasn't quite clear either. Signed-off-by:
-
Janusz Krzysztofik authored
Remove the soc_camera dependencies and move the diver to i2c Lost features, fortunately not used or not critical on test platform: - soc_camera power on/off callback - replaced with clock enable/disable only, no support for platform provided regulators nor power callback, - soc_camera sense request - replaced with arbitrarily selected default master clock rate and pixel clock limit, no support for platform requested values, - soc_camera board flags - no support for platform requested mbus config tweaks. Tested on Amstrad Delta with now out of tree but still locally maintained omap1_camera host driver. Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Sending patches with SVG files via e-mail has a drawback: line size could be bigger than 998, with is the limit given by RFC 5322[1]. So, we need to enforce a lower limit, in order to allow those patches to be properly reviewed. [1] https://tools.ietf.org/html/rfc5322#section-2.1.1 So, use this small Perl script to limit columns size to ~900. use Text::Wrap; $Text::Wrap::columns = 900; $t.=$_ while (<>); print wrap("","",$t); Signed-off-by:
-
Mauro Carvalho Chehab authored
Debian's ImageMagick is currently unable to decode those images. Use scour to simplify the SVG, and provide only one font type, in order to make it more palatable. Signed-off-by: -
Mauro Carvalho Chehab authored
This file is too big, with cause it to require a lot of memory when parsed by texlive. Optimize it, in order to avoid the need of touching at main_memory at texmf.cnf. Signed-off-by:
-
- 17 Jul, 2017 4 commits
-
-
Javier Martinez Canillas authored
The vimc platform drivers define a platform device ID table but these are not set to the .id_table field in the platform driver structure. So the platform device ID table is only used to fill the aliases in the module but are not used for matching (works because the platform subsystem fallbacks to the driver's name if no .id_table is set). But this also means that the platform device ID table isn't used if the driver is built-in, which leads to the following build warning: This causes the following build warnings when the driver is built-in: drivers/media/platform/vimc//vimc-capture.c:528:40: warning: ‘vimc_cap_driver_ids’ defined but not used [-Wunused-const-variable=] static const struct platform_device_id vimc_cap_driver_ids[] = { ^~~~~~~~~~~~~~~~~~~ drivers/media/platform/vimc//vimc-debayer.c:588:40: warning: ‘vimc_deb_driver_ids’ defined but not used [-Wunused-const-variable=] static const struct platform_device_id vimc_deb_driver_ids[] = { ^~~~~~~~~~~~~~~~~~~ drivers/media/platform/vimc//vimc-scaler.c:442:40: warning: ‘vimc_sca_driver_ids’ defined but not used [-Wunused-const-variable=] static const struct platform_device_id vimc_sca_driver_ids[] = { ^~~~~~~~~~~~~~~~~~~ drivers/media/platform/vimc//vimc-sensor.c:376:40: warning: ‘vimc_sen_driver_ids’ defined but not used [-Wunused-const-variable=] static const struct platform_device_id vimc_sen_driver_ids[] = { ^~~~~~~~~~~~~~~~~~~ Reported-by:Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Javier Martinez Canillas <javierm@redhat.com> Reviewed-by:
Helen Koike <helen.koike@collabora.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com>
-
Mauro Carvalho Chehab authored
Instead of directly using -Wno-foo, use cc-disable-warning, as it checks if the compiler has the warnings we want to disable. Signed-off-by: -
Mauro Carvalho Chehab authored
Get rid of those two warnings: drivers/media/platform/davinci/vpif_capture.c: In function 'vpif_remove': drivers/media/platform/davinci/vpif_capture.c:1722:21: warning: variable 'common' set but not used [-Wunused-but-set-variable] struct common_obj *common; ^~~~~~ drivers/media/platform/davinci/vpif_display.c: In function 'vpif_remove': drivers/media/platform/davinci/vpif_display.c:1342:21: warning: variable 'common' set but not used [-Wunused-but-set-variable] struct common_obj *common; ^~~~~~ Signed-off-by: -
Mauro Carvalho Chehab authored
Linux v4.13-rc1 * tag 'v4.13-rc1': (11136 commits) Linux v4.13-rc1 random: reorder READ_ONCE() in get_random_uXX random: suppress spammy warnings about unseeded randomness replace incorrect strscpy use in FORTIFY_SOURCE kmod: throttle kmod thread limit kmod: add test driver to stress test the module loader MAINTAINERS: give kmod some maintainer love xtensa: use generic fb.h fault-inject: add /proc/<pid>/fail-nth fault-inject: simplify access check for fail-nth fault-inject: make fail-nth read/write interface symmetric fault-inject: parse as natural 1-based value for fail-nth write interface fault-inject: automatically detect the number base for fail-nth write interface kernel/watchdog.c: use better pr_fmt prefix MAINTAINERS: move the befs tree to kernel.org lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int mm: fix overflow check in expand_upwards() ubifs: Set double hash cookie also for RENAME_EXCHANGE ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs ubifs: Don't leak kernel memory to the MTD ...
-
- 15 Jul, 2017 1 commit
-
-
Linus Torvalds authored
-
