Add quirk SDHCI_QUIRK2_HOST_OFF_CARD_ON to cater for the case when the
card keeps power during suspend but the host controller does not i.e.
the card power is not controlled by the host controller.  In that
case, the controller must be fully reset on resume.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Let drivers specify the use of high-capacity erase size.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Convert all instances of pr_* prints within the driver
to instead use dev_* prints.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

The MMC_GEN_CMD (CMD56) doesn't need to check busy signal.
So, the patch fixes the setting.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This patch fixes following issues when HS200 is enabled:

1. If executing_tuning() host ops is called without mmc_host_clk_hold(),
   card clocks might get turned off (if MMC_CLK_GATING is enabled)
   while execute_tuning() is in progress. So this patch makes sure
   that execute_tuning() is called with mmc_host_clk_hold().

2. If host timing mode is set to HS200 mode, there should not be
   any communication with the card until execute_tuning() is completed.
   But there is a chance that CMD6 might be sent to enable set HPI_EN
   (of HPI_MGMT field in EXT_CSD) before execute_tuning() is called.
   So this patch moves this operation after execute_tuning() is completed.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: girish.shivananjappa@linaro.org
Signed-off-by: Chris Ball <cjb@laptop.org>

Otherwise we can get following warning when re-loading the omap_hsmmc
driver module when gpio_twl4030 module is not loaded:

omap_hsmmc omap_hsmmc.0: Unbalanced pm_runtime_enable!
omap_hsmmc omap_hsmmc.0: Unable to grab MMC CD IRQ
omap_hsmmc: probe of omap_hsmmc.0 failed with error -22
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Make sure mmc_start_req cancels the prepared job, if the request
was prevented to be started due to the card has been removed.

This bug was introduced in commit:
mmc: allow upper layers to know immediately if card has been removed
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Most parts of the enable / disable API are no longer used and
can be removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

If TMIO MMC is used in polling mode, or the card is non-removable, or
card-detection is performed, using an external interrupt, there is no
need to enable controller native card hotplug interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>

MMC1 is not the only instance that can be used/wired for SD.
So remove this assumption from the driver.

Now that all the mmc id based usage is removed, get rid of all the DEVID
defines and also the 'id' field from the omap_hsmmc_host structure.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Now that omap_hsmmc_set_power() already has a check to return 0
if !host->vcc, it seems like it can be used even on MMC4 instead
of the dummy omap_hsmmc_4_set_power().

This also helps get rid of all the host->id based check to
populate the right function for on-chip/external level
shifting and use omap_hsmmc_set_power() for all MMC modules.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Use omap_hsmmc_235_set_poweri() (now renamed as omap_hsmmc_set_power())
for MMC1 instance as well and get rid of omap_hsmmc_1_set_power()
completely.

omap_hsmmc_235_set_power() seems to be implemented as a superset of
omap_hsmmc_1_set_power() with additional functionality implemented
based on additional checks and hence should just work for MMC1
as well.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Use OMAP_HSMMC_SUPPORTS_DUAL_VOLT flag instead of host->id
for identifying SD bus voltage capabilities.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

set_sleep seems to be unused in omap_hsmmc driver. so get rid of it.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Git rid of hardcoded tx/rx DMA channels based on pdev->id
and use platform_get_resource_byname() to retrieve them
instead.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.

Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>

3ec7699d3bb1b0ee7 ("mmc: dw_mmc: Add support for pre_req and post_req")
broke non-IDMAC DMA, because dw_mci_pre_dma_transfer() is valid only if
using internal DMA. In case of using other DMA it returns -ENOSYS. It
prevents the DMA operations.  This patch makes dw_mci_pre_dma_transfer()
effective in all DMA cases again.
Reported-by: James Hogan <james@albanarts.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

When disable CONFIG_MMC_DW_IDMAC, can see the compiler error.
Because in dw_mci_post_req(), called the dw_mci_get_dma_dir().
But that function is in #ifdef CONFIG_MMC_DW_IDMAC.

I think that function is generic function.
Not need the CONFIG_MMC_DW_IDMAC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

External circuitry like level shifters may limit the maximum operation
speed of the hsmmc controller. Add a field to struct omap2_hsmmc_info
so boards can adjust the setting on demand.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

In CLKENA register, can support 16-SD card clocks.
If support correctly, must shift with slot-id.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

SD card read was failing (data crc error) on some cards at
maximum possible frequency on P1010 (CCB frequency set to 400MHz).
Some clock deviations are also observed at this frequency.
Hence reduced the mmc clock freq.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This patch is added just debug message.  Almost features need to use the
CMD23.  But we didn't see the debug message for sbc.  If sbc's message
can see, should be help for debugging.  (We can check whether use the
cmd23 or not.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This patch implements pre_req and post_req in dw_mmc to support
asynchronous mmc request.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Tegra30 differs from Tegra20 in a number of ways. This patch implements a
minimal set of differences in order to get the Cardhu board's SD slot and
eMMC working. Given the diffs between the mainline sdhci-tegra.c and our
downstream versions, I expect we'll eventually need to add many more
differences, hence the seemingly heavy-weight addition of the soc_data
structure.

* Tegra30 doesn't need to override register access to SDHCI_HOST_VERSION or
  SDHCI_INT_ENABLE.

* Tegra30 needs quirk SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

For FSL ESDHC controllers, when entering sleep the controller will power off,
therefore the registers will lose their values, and the driver should save
the value of registers during suspend and write them back during resume.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Some platforms require saving/restoring registers across suspend/resume;
this hook allows them to do that inside their driver.
Signed-off-by: Chris Ball <cjb@laptop.org>

When use the IDMAC, we can also want to use the pdata->blk-setting.
So if pdata->blk-setting is unset, use the default value.
if not, use the pdata->blk-setting.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

This patch adds the capability of power off notify for dw-mmc controller.
In order to use Girish's patch:
mmc: core: Add Power Off Notify Feature eMMC 4.5
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

Pull vfs pile 1 from Al Viro:
 "This is _not_ all; in particular, Miklos' and Jan's stuff is not there
  yet."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
  ext4: initialization of ext4_li_mtx needs to be done earlier
  debugfs-related mode_t whack-a-mole
  hfsplus: add an ioctl to bless files
  hfsplus: change finder_info to u32
  hfsplus: initialise userflags
  qnx4: new helper - try_extent()
  qnx4: get rid of qnx4_bread/qnx4_getblk
  take removal of PF_FORKNOEXEC to flush_old_exec()
  trim includes in inode.c
  um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
  um: embed ->stub_pages[] into mmu_context
  gadgetfs: list_for_each_safe() misuse
  ocfs2: fix leaks on failure exits in module_init
  ecryptfs: make register_filesystem() the last potential failure exit
  ntfs: forgets to unregister sysctls on register_filesystem() failure
  logfs: missing cleanup on register_filesystem() failure
  jfs: mising cleanup on register_filesystem() failure
  make configfs_pin_fs() return root dentry on success
  configfs: configfs_create_dir() has parent dentry in dentry->d_parent
  configfs: sanitize configfs_create()
  ...

Pull munmap/truncate race fixes from Al Viro:
 "Fixes for racy use of unmap_vmas() on truncate-related codepaths"

* 'vm' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  VM: make zap_page_range() callers that act on a single VMA use separate helper
  VM: make unmap_vmas() return void
  VM: don't bother with feeding upper limit to tlb_finish_mmu() in exit_mmap()
  VM: make zap_page_range() return void
  VM: can't go through the inner loop in unmap_vmas() more than once...
  VM: unmap_page_range() can return void

Pull security subsystem updates for 3.4 from James Morris:
 "The main addition here is the new Yama security module from Kees Cook,
  which was discussed at the Linux Security Summit last year.  Its
  purpose is to collect miscellaneous DAC security enhancements in one
  place.  This also marks a departure in policy for LSM modules, which
  were previously limited to being standalone access control systems.
  Chromium OS is using Yama, and I believe there are plans for Ubuntu,
  at least.

  This patchset also includes maintenance updates for AppArmor, TOMOYO
  and others."

Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
  AppArmor: Fix location of const qualifier on generated string tables
  TOMOYO: Return error if fails to delete a domain
  AppArmor: add const qualifiers to string arrays
  AppArmor: Add ability to load extended policy
  TOMOYO: Return appropriate value to poll().
  AppArmor: Move path failure information into aa_get_name and rename
  AppArmor: Update dfa matching routines.
  AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
  AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
  AppArmor: Add const qualifiers to generated string tables
  AppArmor: Fix oops in policy unpack auditing
  AppArmor: Fix error returned when a path lookup is disconnected
  KEYS: testing wrong bit for KEY_FLAG_REVOKED
  TOMOYO: Fix mount flags checking order.
  security: fix ima kconfig warning
  AppArmor: Fix the error case for chroot relative path name lookup
  AppArmor: fix mapping of META_READ to audit and quiet flags
  AppArmor: Fix underflow in xindex calculation
  AppArmor: Fix dropping of allowed operations that are force audited
  AppArmor: Add mising end of structure test to caps unpacking
  ...

Pull crypto update from Herbert Xu:
 "* sha512 bug fixes (already in your tree).
  * SHA224/SHA384 AEAD support in caam.
  * X86-64 optimised version of Camellia.
  * Tegra AES support.
  * Bulk algorithm registration interface to make driver registration easier.
  * padata race fixes.
  * Misc fixes."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (31 commits)
  padata: Fix race on sequence number wrap
  padata: Fix race in the serialization path
  crypto: camellia - add assembler implementation for x86_64
  crypto: camellia - rename camellia.c to camellia_generic.c
  crypto: camellia - fix checkpatch warnings
  crypto: camellia - rename camellia module to camellia_generic
  crypto: tcrypt - add more camellia tests
  crypto: testmgr - add more camellia test vectors
  crypto: camellia - simplify key setup and CAMELLIA_ROUNDSM macro
  crypto: twofish-x86_64/i586 - set alignmask to zero
  crypto: blowfish-x86_64 - set alignmask to zero
  crypto: serpent-sse2 - combine ablk_*_init functions
  crypto: blowfish-x86_64 - use crypto_[un]register_algs
  crypto: twofish-x86_64-3way - use crypto_[un]register_algs
  crypto: serpent-sse2 - use crypto_[un]register_algs
  crypto: serpent-sse2 - remove dead code from serpent_sse2_glue.c::serpent_sse2_init()
  crypto: twofish-x86 - Remove dead code from twofish_glue_3way.c::init()
  crypto: In crypto_add_alg(), 'exact' wants to be initialized to 0
  crypto: caam - fix gcc 4.6 warning
  crypto: Add bulk algorithm registration interface
  ...

Pull hwmon changes for v3.4 from Guenter Roeck:
 "Mostly cleanup.  No new drivers this time around, but support for
  several chips added to existing drivers: TPS40400, TPS40422, MTD040,
  MAX34446, ZL9101M, ZL9117M, and LM96080.  Also, added watchdog support
  for SCH56xx, and additional attributes for a couple of drivers."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (137 commits)
  hwmon: (sch56xx) Add support for the integrated watchdog (v2)
  hwmon: (w83627ehf) Add support for temperature offset registers
  hwmon: (jc42) Remove unnecessary device IDs
  hwmon: (zl6100) Add support for ZL9101M and ZL9117M
  hwmon: (adm1275) Add support for ADM1075
  hwmon: (max34440) Add support for MAX34446
  hwmon: (pmbus) Add more virtual registers
  hwmon: (pmbus) Add support for Lineage Power MDT040
  hwmon: (pmbus) Add support for TI TPS40400 and TPS40422
  hwmon: (max34440) Add support for 'lowest' output voltage attribute
  hwmon: (jc42) Convert to use devm_kzalloc
  hwmon: (max16065) Convert to use devm_kzalloc
  hwmon: (smm665) Convert to use devm_kzalloc
  hwmon: (ltc4261) Convert to use devm_kzalloc
  hwmon: (pmbus) Simplify remove functions
  hwmon: (pmbus) Convert pmbus drivers to use devm_kzalloc
  hwmon: (lineage-pem) Convert to use devm_kzalloc
  hwmon: (hwmon-vid) Fix checkpatch issues
  hwmon: (hwmon-vid) Add new entries to VRM model table
  hwmon: (lm80) Add detection of NatSemi/TI LM96080
  ...

Pull regulator updates for 3.4 from Mark Brown:
 "This has been a fairly quiet release from a regulator point of view,
  the only real framework features added were devm support and a
  convenience helper for setting up fixed voltage regulators.

  We also added a couple of drivers (but will drop the BQ240022 driver
  via the arm-soc tree as it's been replaced by the more generic
  gpio-regulator driver) and Axel Lin continued his relentless and
  generally awesome stream of fixes and cleanups."

* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (93 commits)
  regulator: Fix up a confusing dev_warn when DT lookup fails
  regulator: Convert tps6507x to set_voltage_sel
  regulator: Refactor tps6507x to use one tps6507x_pmic_ops for all LDOs and DCDCs
  regulator: Make s5m8767_get_voltage_register always return correct register
  regulator: s5m8767: Check pdata->buck[2|3|4]_gpiodvs earlier
  regulator: tps65910: Provide settling time for DCDC voltage change
  regulator: Add Anatop regulator driver
  regulator: Simplify implementation of tps65912_get_voltage_dcdc
  regulator: Use tps65912_set_voltage_sel for both DCDCx and LDOx
  regulator: tps65910: Provide settling time for enabling rails
  regulator: max8925: Use DIV_ROUND_UP macro
  regulator: tps65912: Use simple equations to get register address
  regulator: Fix the logic of tps65910_get_mode
  regulator: Merge tps65217_pmic_ldo234_ops and tps65217_pmic_dcdc_ops to tps65217_pmic_ops
  regulator: Use DIV_ROUND_CLOSEST in wm8350_isink_get_current
  regulator: Use array to store dcdc_range settings for tps65912
  regulator: Rename s5m8767_convert_voltage to s5m8767_convert_voltage_to_sel
  regulator: tps6524x: Remove unneeded comment for N_REGULATORS
  regulator: Rename set_voltage_sel callback function name to *_sel
  regulator: Fix s5m8767_set_voltage_time_sel calculation value
  ...

Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
 "Nothing big really stands out; by patch count lots of fixes to the
  mlx4 driver plus some cleanups and fixes to the core and other
  drivers."

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
  mlx4_core: Scale size of MTT table with system RAM
  mlx4_core: Allow dynamic MTU configuration for IB ports
  IB/mlx4: Fix info returned when querying IBoE ports
  IB/mlx4: Fix possible missed completion event
  mlx4_core: Report thermal error events
  mlx4_core: Fix one more static exported function
  IB: Change CQE "csum_ok" field to a bit flag
  RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
  RDMA/cxgb3: Don't pass irq flags to flush_qp()
  mlx4_core: Get rid of redundant ext_port_cap flags
  RDMA/ucma: Fix AB-BA deadlock
  IB/ehca: Fix ilog2() compile failure
  IB: Use central enum for speed instead of hard-coded values
  IB/iser: Post initial receive buffers before sending the final login request
  IB/iser: Free IB connection resources in the proper place
  IB/srp: Consolidate repetitive sysfs code
  IB/srp: Use pr_fmt() and pr_err()/pr_warn()
  IB/core: Fix SDR rates in sysfs
  mlx4: Enforce device max FMR maps in FMR alloc
  IB/mlx4: Set bad_wr for invalid send opcode
  ...