Daniel Borkmann says:

====================
pull-request: bpf 2019-01-20

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.

2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.

3) Fix map in map masking to prevent out-of-bounds access under
   speculative execution, from Daniel.

4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
   pacing, from Yuchung.

5) Fix json writer license in bpftool, from Thomas.

6) Fix AF_XDP to check if an actually queue exists during umem
   setup, from Krzysztof.

7) Several fixes to BPF stackmap's build id handling. Another fix
   for bpftool build to account for libbfd variations wrt linking
   requirements, from Stanislav.

8) Fix BPF samples build with clang by working around missing asm
   goto, from Yonghong.

9) Fix libbpf to retry program load on signal interrupt, from Lorenz.

10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:

    BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
    BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942

    kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
    check_memory_region_inline mm/kasan/kasan.c:260 [inline]
    check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
    memcpy+0x23/0x50 mm/kasan/kasan.c:302
    memcpy include/linux/string.h:345 [inline]
    skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    __pskb_copy include/linux/skbuff.h:1053 [inline]
    pskb_copy include/linux/skbuff.h:2904 [inline]
    skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
    ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
    sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
    __netdev_start_xmit include/linux/netdevice.h:4325 [inline]
    netdev_start_xmit include/linux/netdevice.h:4334 [inline]
    xmit_one net/core/dev.c:3219 [inline]
    dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
    __dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
    dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
    __bpf_tx_skb net/core/filter.c:2016 [inline]
    __bpf_redirect_common net/core/filter.c:2054 [inline]
    __bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
    ____bpf_clone_redirect net/core/filter.c:2094 [inline]
    bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
    bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000

The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.

Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.

Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.

The test itself can be run only from commit 1cf1cae9 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.

Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.

Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use napi_consume_skb() to get bulk free.  Note that napi_consume_skb is
safe to call in a non-napi context as long as the napi_budget flag is
correct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.

Prevent the phy driver from registering if the features field is missing.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit in Clang expanded the -Wstring-plus-int warning, showing
some odd behavior in this file.

drivers/isdn/hardware/avm/b1.c:426:30: warning: adding 'int' to a string does not append to the string [-Wstring-plus-int]
                cinfo->version[j] = "\0\0" + 1;
                                    ~~~~~~~^~~
drivers/isdn/hardware/avm/b1.c:426:30: note: use array indexing to silence this warning
                cinfo->version[j] = "\0\0" + 1;
                                           ^
                                    &      [  ]
1 warning generated.

This is equivalent to just "\0". Nick pointed out that it is smarter to
use "" instead of "\0" because "" is used elsewhere in the kernel and
can be deduplicated at the linking stage.

Link: https://github.com/ClangBuiltLinux/linux/issues/309Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-01-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')

The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.

Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.

Fixes: f5bc2c5d ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Advertised and configured FEC query failure resulted in printing
wrong error code.

Fixes: 6cfa9460 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.

Prior to:
commit '88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.

Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Precise and non-ambiguous license information is important. The recent
relicensing of the bpftools introduced a license conflict.

The files have now:

     SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause

and

     * This program is free software; you can redistribute it and/or
     * modify it under the terms of the GNU General Public License
     * as published by the Free Software Foundation; either version
     * 2 of the License, or (at your option) any later version

Amazingly about 20 people acked that change and neither they nor the
committer noticed. Oh well.

Digging deeper: The files were imported from the iproute2 repository with
the GPL V2 or later boiler plate text in commit b66e907c ("tools:
bpftool: copy JSON writer from iproute2 repository")

Looking at the iproute2 repository at

  git://git.kernel.org/pub/scm/network/iproute2/iproute2.git

the following commit is the equivivalent:

  commit d9d8c839 ("json_writer: add SPDX Identifier (GPL-2/BSD-2)")

That commit explicitly removes the boiler plate and relicenses the code
uner GPL-2.0-only and BSD-2-Clause. As Steven wrote the original code and
also the relicensing commit, it's assumed that the relicensing was intended
to do exaclty that. Just the kernel side update failed to remove the boiler
plate. Do so now.

Fixes: 907b2236 ("tools: bpftool: dual license all files")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Sean Young <sean@mess.org>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: David Calavera <david.calavera@gmail.com>
Cc: Andrey Ignatov <rdna@fb.com>
Cc: Joe Stringer <joe@wand.net.nz>
Cc: David Ahern <dsahern@gmail.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Petar Penkov <ppenkov@stanford.edu>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
CC: okash.khawaja@gmail.com
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

During review I noticed that inner meta map setup for map in
map is buggy in that it does not propagate all needed data
from the reference map which the verifier is later accessing.

In particular one such case is index masking to prevent out of
bounds access under speculative execution due to missing the
map's unpriv_array/index_mask field propagation. Fix this such
that the verifier is generating the correct code for inlined
lookups in case of unpriviledged use.

Before patch (test_verifier's 'map in map access' dump):

  # bpftool prog dump xla id 3
     0: (62) *(u32 *)(r10 -4) = 0
     1: (bf) r2 = r10
     2: (07) r2 += -4
     3: (18) r1 = map[id:4]
     5: (07) r1 += 272                |
     6: (61) r0 = *(u32 *)(r2 +0)     |
     7: (35) if r0 >= 0x1 goto pc+6   | Inlined map in map lookup
     8: (54) (u32) r0 &= (u32) 0      | with index masking for
     9: (67) r0 <<= 3                 | map->unpriv_array.
    10: (0f) r0 += r1                 |
    11: (79) r0 = *(u64 *)(r0 +0)     |
    12: (15) if r0 == 0x0 goto pc+1   |
    13: (05) goto pc+1                |
    14: (b7) r0 = 0                   |
    15: (15) if r0 == 0x0 goto pc+11
    16: (62) *(u32 *)(r10 -4) = 0
    17: (bf) r2 = r10
    18: (07) r2 += -4
    19: (bf) r1 = r0
    20: (07) r1 += 272                |
    21: (61) r0 = *(u32 *)(r2 +0)     | Index masking missing (!)
    22: (35) if r0 >= 0x1 goto pc+3   | for inner map despite
    23: (67) r0 <<= 3                 | map->unpriv_array set.
    24: (0f) r0 += r1                 |
    25: (05) goto pc+1                |
    26: (b7) r0 = 0                   |
    27: (b7) r0 = 0
    28: (95) exit

After patch:

  # bpftool prog dump xla id 1
     0: (62) *(u32 *)(r10 -4) = 0
     1: (bf) r2 = r10
     2: (07) r2 += -4
     3: (18) r1 = map[id:2]
     5: (07) r1 += 272                |
     6: (61) r0 = *(u32 *)(r2 +0)     |
     7: (35) if r0 >= 0x1 goto pc+6   | Same inlined map in map lookup
     8: (54) (u32) r0 &= (u32) 0      | with index masking due to
     9: (67) r0 <<= 3                 | map->unpriv_array.
    10: (0f) r0 += r1                 |
    11: (79) r0 = *(u64 *)(r0 +0)     |
    12: (15) if r0 == 0x0 goto pc+1   |
    13: (05) goto pc+1                |
    14: (b7) r0 = 0                   |
    15: (15) if r0 == 0x0 goto pc+12
    16: (62) *(u32 *)(r10 -4) = 0
    17: (bf) r2 = r10
    18: (07) r2 += -4
    19: (bf) r1 = r0
    20: (07) r1 += 272                |
    21: (61) r0 = *(u32 *)(r2 +0)     |
    22: (35) if r0 >= 0x1 goto pc+4   | Now fixed inlined inner map
    23: (54) (u32) r0 &= (u32) 0      | lookup with proper index masking
    24: (67) r0 <<= 3                 | for map->unpriv_array.
    25: (0f) r0 += r1                 |
    26: (05) goto pc+1                |
    27: (b7) r0 = 0                   |
    28: (b7) r0 = 0
    29: (95) exit

Fixes: b2157399 ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Dan reported that bpftool does not compile for him:

  $ make tools/bpf
    DESCEND  bpf

  Auto-detecting system features:
  ..                        libbfd: [ on  ]
  ..        disassembler-four-args: [ OFF ]

    DESCEND  bpftool

  Auto-detecting system features:
  ..                        libbfd: [ on  ]
  ..        disassembler-four-args: [ OFF ]

    CC       /opt/linux.git/tools/bpf/bpftool/net.o
  In file included from /opt/linux.git/tools/include/uapi/linux/pkt_cls.h:6:0,
                 from /opt/linux.git/tools/include/uapi/linux/tc_act/tc_bpf.h:14,
                 from net.c:13:
  net.c: In function 'show_dev_tc_bpf':
  net.c:164:21: error: 'TC_H_CLSACT' undeclared (first use in this function)
    handle = TC_H_MAKE(TC_H_CLSACT, TC_H_MIN_INGRESS);
  [...]

Fix it by importing pkt_sched.h header copy into tooling
infrastructure.

Fixes: 49a249c3 ("tools/bpftool: copy a few net uapi headers to tools directory")
Fixes: f6f3bac0 ("tools/bpf: bpftool: add net support")
Reported-by: Dan Gilson <dan_gilson@yahoo.com>
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=202315Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Ido Schimmel says:

====================
mlxsw: Various fixes

This patchset contains small fixes in mlxsw and one fix in the bridge
driver.

Patches #1-#4 perform small adjustments in PCI and FID code following
recent tests that were performed on the Spectrum-2 ASIC.

Patch #5 fixes the bridge driver to mark FDB entries that were added by
user as such. Otherwise, these entries will be ignored by underlying
switch drivers.

Patch #6 fixes a long standing issue in mlxsw where the driver
incorrectly programmed static FDB entries as both static and sticky.

Patches #7-#8 add test cases for above mentioned bugs.

Please consider patches #1, #2 and #4 for stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that externally learned FDB entries can roam, but not age out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that externally learned FDB entries added from user space are
marked as offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently treats static FDB entries as both static and
sticky. This is incorrect and prevents such entries from being roamed to
a different port via learning.

Fix this by configuring static entries with ageing disabled and roaming
enabled.

In net-next we can add proper support for the newly introduced 'sticky'
flag.

Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.

In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.

The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.

Fixes: 816a3bed ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>

When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS.  While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.

Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return an appropriate error in the case when the driver timeouts on waiting
for firmware to go out of PCI reset.

Fixes: 233fa44b ("mlxsw: pci: Implement reset done check")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).

In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.

The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.

Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.

Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.

Before commit 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.

Fixes: 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update email addresses of liquidio driver maintainers.  Also remove a
former maintainer.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Acked-by: Derek Chickles <dchickles@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"also enables" should not be spelled as one word.

Fixes: cfc80d9a ("net: Introduce net_failover driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.

This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:

[    1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074
[    1.498110] pgd = (ptrval)
[    1.500838] [00000074] *pgd=00000000
[    1.504432] Internal error: Oops: 17 [#1] SMP ARM
[    1.509133] Modules linked in:
[    1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99
[    1.520708] Hardware name: Xilinx Zynq Platform
[    1.525261] Workqueue: events deferred_probe_work_func
[    1.530403] PC is at klist_next+0x10/0xfc
[    1.534403] LR is at device_for_each_child+0x40/0x94
[    1.539361] pc : [<c0683fbc>]    lr : [<c0455d90>]    psr: 200e0013
[    1.545628] sp : ceeefe68  ip : 00000001  fp : ffffe000
[    1.550863] r10: 00000000  r9 : c0c66790  r8 : 00000000
[    1.556079] r7 : c0457d44  r6 : 00000000  r5 : ceeefe8c  r4 : cfa2ec78
[    1.562604] r3 : 00000064  r2 : c0457d44  r1 : ceeefe8c  r0 : 00000064
[    1.569129] Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[    1.576263] Control: 18c5387d  Table: 0ed7804a  DAC: 00000051
[    1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval))
[    1.588280] Stack: (0xceeefe68 to 0xceef0000)
[    1.592630] fe60:                   cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790
[    1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78
[    1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac
[    1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10
[    1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c
[    1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c
[    1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00
[    1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000
[    1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4
[    1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000
[    1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[    1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[    1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94)
[    1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94)
[    1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[    1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40)
[    1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c)
[    1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc)
[    1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0)
[    1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154)
[    1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    1.785689] Exception stack(0xceeeffb0 to 0xceeefff8)
[    1.790739] ffa0:                                     00000000 00000000 00000000 00000000
[    1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010)
[    1.819844] ---[ end trace 3c2c0c8b65399ec9 ]---

The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.

To fix this, we simply add the missing device_del() invocation in the
error path.

Fixes: 69226896 ("mdio_bus: Issue GPIO RESET to PHYs")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix "reference to nonexisting document" warnings.

Fixes: b255e500 ("net: documentation: build a directory structure for drivers")
Signed-off-by: Otto Sabart <ottosabart@seberm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.

Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.

Fixes: 732f2ab7 ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).

To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1

So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.

Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.

To solve this issue, when logging with device IOTLB enabled, we will:

1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
   get HVA, for writable descriptor, get HVA through iovec. For used
   ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
   through GPA. Pay attention this reverse mapping is not guaranteed
   to be unique, so we should log each possible GPA in this case.

This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Cc: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_tstamp.h is an UAPI header, so it was moved under include/uapi.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cb9f1b78, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:

Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
    TX: bytes  packets  errors  dropped carrier collsns
    0          0        1       0       0       0

The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).

This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.

Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If sch_fq packet scheduler is not used, TCP can fallback to
internal pacing, but this requires sk_pacing_status to
be properly set.

Fixes: 8c4b4c7e ("bpf: Add setsockopt helper function to bpf")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

In sock_setsockopt() (net/core/sock.h), when SO_MARK option is used
to change sk_mark, sk_dst_reset(sk) is called. The same should be
done in bpf_setsockopt().

Fixes: 8c4b4c7e ("bpf: Add setsockopt helper function to bpf")
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

After commit 23b0269e ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.

And this issue was found with LTP/network tests as well.

Fixes: 23b0269e ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 4cdeeee9 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.

This is related to the problem addressed in the commit 719f8358
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.

The issue was found with LTP/network tests (UDP-Lite test-cases).

Fixes: 4cdeeee9 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>