There is no need to always call blocking console_lock() in
console_cpu_notify(), it's quite possible that console_sem can
be locked by other CPU on the system, either already printing
or soon to begin printing the messages. console_lock() in this
case can simply block CPU hotplug for unknown period of time
(console_unlock() is time unbound). Not that hotplug is very
fast, but still, with other CPUs being online and doing
printk() console_cpu_notify() can stuck.

Use console_trylock() instead and opt-out if console_sem is
already acquired from another CPU, since that CPU will do
the printing for us.

Link: http://lkml.kernel.org/r/20170121104729.8585-1-sergey.senozhatsky@gmail.com
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>

Pull printk updates from Petr Mladek:

 - Add Petr Mladek, Sergey Senozhatsky as printk maintainers, and Steven
   Rostedt as the printk reviewer. This idea came up after the
   discussion about printk issues at Kernel Summit. It was formulated
   and discussed at lkml[1].

 - Extend a lock-less NMI per-cpu buffers idea to handle recursive
   printk() calls by Sergey Senozhatsky[2]. It is the first step in
   sanitizing printk as discussed at Kernel Summit.

   The change allows to see messages that would normally get ignored or
   would cause a deadlock.

   Also it allows to enable lockdep in printk(). This already paid off.
   The testing in linux-next helped to discover two old problems that
   were hidden before[3][4].

 - Remove unused parameter by Sergey Senozhatsky. Clean up after a past
   change.

[1] http://lkml.kernel.org/r/1481798878-31898-1-git-send-email-pmladek@suse.com
[2] http://lkml.kernel.org/r/20161227141611.940-1-sergey.senozhatsky@gmail.com
[3] http://lkml.kernel.org/r/20170215044332.30449-1-sergey.senozhatsky@gmail.com
[4] http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.com

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  printk: drop call_console_drivers() unused param
  printk: convert the rest to printk-safe
  printk: remove zap_locks() function
  printk: use printk_safe buffers in printk
  printk: report lost messages in printk safe/nmi contexts
  printk: always use deferred printk when flush printk_safe lines
  printk: introduce per-cpu safe_print seq buffer
  printk: rename nmi.c and exported api
  printk: use vprintk_func in vprintk()
  MAINTAINERS: Add printk maintainers

Pull modules updates from Jessica Yu:
 "Summary of modules changes for the 4.11 merge window:

   - A few small code cleanups

   - Add modules git tree url to MAINTAINERS"

* tag 'modules-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  MAINTAINERS: add tree for modules
  module: fix memory leak on early load_module() failures
  module: Optimize search_module_extables()
  modules: mark __inittest/__exittest as __maybe_unused
  livepatch/module: print notice of TAINT_LIVEPATCH
  module: Drop redundant declaration of struct module

Pull tty/serial driver updates from Greg KH:
 "Here is the big tty/serial driver patchset for 4.11-rc1.

  Not much here, but a lot of little fixes and individual serial driver
  updates all over the subsystem. Majority are for the sh-sci driver and
  platform (the arch-specific changes have acks from the maintainer).

  The start of the "serial bus" code is here as well, but nothing is
  converted to use it yet. That work is still ongoing, hopefully will
  start to show up across different subsystems for 4.12 (bluetooth is
  one major place that will be used.)

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
  tty: pl011: Work around QDF2400 E44 stuck BUSY bit
  atmel_serial: Use the fractional divider when possible
  tty: Remove extra include in HVC console tty framework
  serial: exar: Enable MSI support
  serial: exar: Move register defines from uapi header to consumer site
  serial: pci: Remove unused pci_boards entries
  serial: exar: Move Commtech adapters to 8250_exar as well
  serial: exar: Fix feature control register constants
  serial: exar: Fix initialization of EXAR registers for ports > 0
  serial: exar: Fix mapping of port I/O resources
  serial: sh-sci: fix hardware RX trigger level setting
  tty/serial: atmel: ensure state is restored after suspending
  serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
  serdev: ttyport: check whether tty_init_dev() fails
  serial: 8250_pci: make pciserial_detach_ports() static
  ARM: dts: STiH410-b2260: Enable HW flow-control
  ARM: dts: STiH407-family: Use new Pinctrl groups
  ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
  ARM: dts: STiH410-b2260: Identify the UART RTS line
  dt-bindings: serial: Update 'uart-has-rtscts' description
  ...

Pull staging/iio driver updates from Greg KH:
 "Here is the big staging and iio driver patchsets for 4.11-rc1.

  We almost broke even this time around, with only a few thousand lines
  added overall, as we removed the old and obsolete i4l code, but added
  some new drivers for the RPi platform, as well as adding some new IIO
  drivers.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (669 commits)
  Staging: vc04_services: Fix the "space prohibited" code style errors
  Staging: vc04_services: Fix the "wrong indent" code style errors
  staging: octeon: Use net_device_stats from struct net_device
  Staging: rtl8192u: ieee80211: ieee80211.h - style fix
  Staging: rtl8192u: ieee80211: ieee80211_tx.c - style fix
  Staging: rtl8192u: ieee80211: rtl819x_BAProc.c - style fix
  Staging: rtl8192u: ieee80211: ieee80211_module.c - style fix
  Staging: rtl8192u: ieee80211: rtl819x_TSProc.c - style fix
  Staging: rtl8192u: r8192U.h - style fix
  Staging: rtl8192u: r8192U_core.c - style fix
  Staging: rtl8192u: r819xU_cmdpkt.c - style fix
  staging: rtl8192u: blank lines aren't necessary before a close brace '}'
  staging: rtl8192u: Adding space after enum and struct definition
  staging: rtl8192u: Adding space after struct definition
  Staging: ks7010: Add required and preferred spaces around operators
  Staging: ks7010: ks*: Remove redundant blank lines
  Staging: ks7010: ks*: Add missing blank lines after declarations
  staging: visorbus, replace init_timer with setup_timer
  staging: vt6656: rxtx.c Removed multiple dereferencing
  staging: vt6656: Alignment match open parenthesis
  ...

Merge tag 'driver-core-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here is the "small" driver core patches for 4.11-rc1.

  Not much here, some firmware documentation and self-test updates, a
  debugfs code formatting issue, and a new feature for call_usermodehelper
  to make it more robust on systems that want to lock it down in a more
  secure way.

  All of these have been linux-next for a while now with no reported
  issues"

* tag 'driver-core-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: handle null pointers while printing node name and path
  Introduce STATIC_USERMODEHELPER to mediate call_usermodehelper()
  Make static usermode helper binaries constant
  kmod: make usermodehelper path a const string
  firmware: revamp firmware documentation
  selftests: firmware: send expected errors to /dev/null
  selftests: firmware: only modprobe if driver is missing
  platform: Print the resource range if device failed to claim
  kref: prefer atomic_inc_not_zero to atomic_add_unless
  debugfs: improve formatting of debugfs_real_fops()

Pull char/misc driver updates from Greg KH:
 "Here is the big char/misc driver patchset for 4.11-rc1.

  Lots of different driver subsystems updated here: rework for the
  hyperv subsystem to handle new platforms better, mei and w1 and extcon
  driver updates, as well as a number of other "minor" driver updates.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
  goldfish: Sanitize the broken interrupt handler
  x86/platform/goldfish: Prevent unconditional loading
  vmbus: replace modulus operation with subtraction
  vmbus: constify parameters where possible
  vmbus: expose hv_begin/end_read
  vmbus: remove conditional locking of vmbus_write
  vmbus: add direct isr callback mode
  vmbus: change to per channel tasklet
  vmbus: put related per-cpu variable together
  vmbus: callback is in softirq not workqueue
  binder: Add support for file-descriptor arrays
  binder: Add support for scatter-gather
  binder: Add extra size to allocator
  binder: Refactor binder_transact()
  binder: Support multiple /dev instances
  binder: Deal with contexts in debugfs
  binder: Support multiple context managers
  binder: Split flat_binder_object
  auxdisplay: ht16k33: remove private workqueue
  auxdisplay: ht16k33: rework input device initialization
  ...

Pull USB/PHY updates from Greg KH:
 "Here is the big USB and PHY driver updates for 4.11-rc1.

  Nothing major, just the normal amount of churn in the usb gadget and
  dwc and xhci controllers, new device ids, new phy drivers, a new
  usb-serial driver, and a few other minor changes in different USB
  drivers.

  All have been in linux-next for a long time with no reported issues"

* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
  usb: cdc-wdm: remove logically dead code
  USB: serial: keyspan: drop header file
  USB: serial: io_edgeport: drop io-tables header file
  usb: musb: add code comment for clarification
  usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
  usb: misc: usbtest: remove redundant check on retval < 0
  USB: serial: upd78f0730: sort device ids
  USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
  ohci-hub: fix typo in dbg_port macro
  usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
  usb: musb: tusb6010: Clean up tusb_omap_dma structure
  usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
  usb: musb: cppi_dma: Clean up cppi structure
  usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
  usb: musb: dma: Add a DMA completion platform callback
  drivers: usb: usbip: Add missing break statement to switch
  usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
  USB: serial: mos7840: fix another NULL-deref at open
  USB: serial: console: clean up sanity checks
  USB: serial: console: fix uninitialised spinlock
  ...

Pull arm64 updates from Will Deacon:
 - Errata workarounds for Qualcomm's Falkor CPU
 - Qualcomm L2 Cache PMU driver
 - Qualcomm SMCCC firmware quirk
 - Support for DEBUG_VIRTUAL
 - CPU feature detection for userspace via MRS emulation
 - Preliminary work for the Statistical Profiling Extension
 - Misc cleanups and non-critical fixes

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (74 commits)
  arm64/kprobes: consistently handle MRS/MSR with XZR
  arm64: cpufeature: correctly handle MRS to XZR
  arm64: traps: correctly handle MRS/MSR with XZR
  arm64: ptrace: add XZR-safe regs accessors
  arm64: include asm/assembler.h in entry-ftrace.S
  arm64: fix warning about swapper_pg_dir overflow
  arm64: Work around Falkor erratum 1003
  arm64: head.S: Enable EL1 (host) access to SPE when entered at EL2
  arm64: arch_timer: document Hisilicon erratum 161010101
  arm64: use is_vmalloc_addr
  arm64: use linux/sizes.h for constants
  arm64: uaccess: consistently check object sizes
  perf: add qcom l2 cache perf events driver
  arm64: remove wrong CONFIG_PROC_SYSCTL ifdef
  ARM: smccc: Update HVC comment to describe new quirk parameter
  arm64: do not trace atomic operations
  ACPI/IORT: Fix the error return code in iort_add_smmu_platform_device()
  ACPI/IORT: Fix iort_node_get_id() mapping entries indexing
  arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA
  perf: xgene: Include module.h
  ...

Pull ARC updates from Vineet Gupta:

 - Intc imporvements [Yuriy]

 - VDK platform updates [Alexey]

* tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [plat-*] ARC_HAS_COH_CACHES no longer relevant
  ARCv2: intc: Delete useless comments in Device Trees
  ARCv2: IDU-intc: Delete deprecated parameters in Device Trees
  ARCv2: IDU-intc: mask all common interrupts by default
  ARCv2: IDU-intc: Use build registers for getting numbers of interrupts
  ARCv2: intc: Set default priority for all core interrupts
  ARCv2: intc: Use runtime value of irq count for setting up intc
  ARCv2: intc: Rework the build time irq count information
  ARC: [intc-*]: confine NR_CPU_IRQS to intc code
  ARCv2: intc: Use ARC_REG_STATUS32 for addressing STATUS32 reg
  arc: vdk: Add support of UIO
  arc: vdk: Add support of MMC controller
  arc: vdk: Disable halt on reset

Pull powerpc updates from Michael Ellerman:
 "Highlights include:

   - Support for direct mapped LPC on POWER9, giving Linux direct access
     to devices that may be on there such as a UART.

   - Memory hotplug support for the Power9 Radix MMU.

   - Add new AUX vectors describing the processor's cache geometry, to
     be used by glibc.

   - The ability for a guest to ask the hypervisor to resize the guest's
     hash table, and in addition support for doing so automatically when
     memory is hotplugged into/out-of the guest. This allows the hash
     table to be sized based on the current memory usage of the guest,
     rather than the maximum possible memory usage.

   - Implementation of optprobes (kprobe optimisation) for powerpc.

  In addition there's the topic branch shared with the KVM tree, which
  includes support for guests to use the Radix MMU on Power9.

  Thanks to:
    Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
    Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
    Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
    Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
    Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
    Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
    Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"

* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
  powerpc/mm/radix: Skip ptesync in pte update helpers
  powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
  powerpc/mm/radix: Update pte update sequence for pte clear case
  powerpc/mm: Update PROTFAULT handling in the page fault path
  powerpc/xmon: Fix data-breakpoint
  powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
  powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
  powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
  powerpc/pseries: Fix typo in parameter description
  powerpc/kprobes: Remove kprobe_exceptions_notify()
  kprobes: Introduce weak variant of kprobe_exceptions_notify()
  powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
  powerpc/powernv: Fix opal_exit tracepoint opcode
  powerpc: Add a prototype for mcount() so it can be versioned
  powerpc: Drop GPL from of_node_to_nid() export to match other arches
  powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
  powerpc/kprobes: Implement Optprobes
  powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
  powerpc: Add helper to check if offset is within relative branch range
  powerpc/bpf: Introduce __PPC_SH64()
  ...

Pull s390 updates from Martin Schwidefsky:

 - New entropy generation for the pseudo random number generator.

 - Early boot printk output via sclp to help debug crashes on boot. This
   needs to be enabled with a kernel parameter.

 - Add proper no-execute support with a bit in the page table entry.

 - Bug fixes and cleanups.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (65 commits)
  s390/syscall: fix single stepped system calls
  s390/zcrypt: make ap_bus explicitly non-modular
  s390/zcrypt: Removed unneeded debug feature directory creation.
  s390: add missing "do {} while (0)" loop constructs to multiline macros
  s390/mm: add cond_resched call to kernel page table dumper
  s390: get rid of MACHINE_HAS_PFMF and MACHINE_HAS_HPAGE
  s390/mm: make memory_block_size_bytes available for !MEMORY_HOTPLUG
  s390: replace ACCESS_ONCE with READ_ONCE
  s390: Audit and remove any remaining unnecessary uses of module.h
  s390: mm: Audit and remove any unnecessary uses of module.h
  s390: kernel: Audit and remove any unnecessary uses of module.h
  s390/kdump: Use "LINUX" ELF note name instead of "CORE"
  s390: add no-execute support
  s390: report new vector facilities
  s390: use correct input data address for setup_randomness
  s390/sclp: get rid of common response code handling
  s390/sclp: don't add new lines to each printed string
  s390/sclp: make early sclp code readable
  s390/sclp: disable early sclp code as soon as the base sclp driver is active
  s390/sclp: move early printk code to drivers
  ...

Pull networking updates from David Miller:
 "Highlights:

   1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
      Varadhan.

   2) Simplify classifier state on sk_buff in order to shrink it a bit.
      From Willem de Bruijn.

   3) Introduce SIPHASH and it's usage for secure sequence numbers and
      syncookies. From Jason A. Donenfeld.

   4) Reduce CPU usage for ICMP replies we are going to limit or
      suppress, from Jesper Dangaard Brouer.

   5) Introduce Shared Memory Communications socket layer, from Ursula
      Braun.

   6) Add RACK loss detection and allow it to actually trigger fast
      recovery instead of just assisting after other algorithms have
      triggered it. From Yuchung Cheng.

   7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.

   8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.

   9) Export MPLS packet stats via netlink, from Robert Shearman.

  10) Significantly improve inet port bind conflict handling, especially
      when an application is restarted and changes it's setting of
      reuseport. From Josef Bacik.

  11) Implement TX batching in vhost_net, from Jason Wang.

  12) Extend the dummy device so that VF (virtual function) features,
      such as configuration, can be more easily tested. From Phil
      Sutter.

  13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
      Dumazet.

  14) Add new bpf MAP, implementing a longest prefix match trie. From
      Daniel Mack.

  15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.

  16) Add new aquantia driver, from David VomLehn.

  17) Add bpf tracepoints, from Daniel Borkmann.

  18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
      Florian Fainelli.

  19) Remove custom busy polling in many drivers, it is done in the core
      networking since 4.5 times. From Eric Dumazet.

  20) Support XDP adjust_head in virtio_net, from John Fastabend.

  21) Fix several major holes in neighbour entry confirmation, from
      Julian Anastasov.

  22) Add XDP support to bnxt_en driver, from Michael Chan.

  23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.

  24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.

  25) Support GRO in IPSEC protocols, from Steffen Klassert"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
  Revert "ath10k: Search SMBIOS for OEM board file extension"
  net: socket: fix recvmmsg not returning error from sock_error
  bnxt_en: use eth_hw_addr_random()
  bpf: fix unlocking of jited image when module ronx not set
  arch: add ARCH_HAS_SET_MEMORY config
  net: napi_watchdog() can use napi_schedule_irqoff()
  tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
  net/hsr: use eth_hw_addr_random()
  net: mvpp2: enable building on 64-bit platforms
  net: mvpp2: switch to build_skb() in the RX path
  net: mvpp2: simplify MVPP2_PRS_RI_* definitions
  net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
  net: mvpp2: remove unused register definitions
  net: mvpp2: simplify mvpp2_bm_bufs_add()
  net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
  net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
  net: mvpp2: release reference to txq_cpu[] entry after unmapping
  net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
  net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
  net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
  ...

Pull gcc-plugins updates from Kees Cook:
 "This includes infrastructure updates and the structleak plugin, which
  performs forced initialization of certain structures to avoid possible
  information exposures to userspace.

  Summary:

   - infrastructure updates (gcc-common.h)

   - introduce structleak plugin for forced initialization of some
     structures"

* tag 'gcc-plugins-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: Add structleak for more stack initialization
  gcc-plugins: consolidate on PASS_INFO macro
  gcc-plugins: add PASS_INFO and build_const_char_string()

Pull rodata updates from Kees Cook:
 "This renames the (now inaccurate) DEBUG_RODATA and related
  SET_MODULE_RONX configs to the more sensible STRICT_KERNEL_RWX and
  STRICT_MODULE_RWX"

* tag 'rodata-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  arch: Rename CONFIG_DEBUG_RODATA and CONFIG_DEBUG_MODULE_RONX
  arch: Move CONFIG_DEBUG_RODATA and CONFIG_SET_MODULE_RONX to be common

Pull usercopy test updates from Kees Cook:
 "This improves the usercopy tests:

   - check zeroing on failed copy_from_user()/get_user() (caught bug on
     ARM)

   - adjust tests for SMAP/PAN (can't zero userspace memory on failure)"

* tag 'usercopy-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  usercopy: Add tests for all get_user() sizes
  usercopy: Adjust tests to deal with SMAP/PAN
  usercopy: add testcases to check zeroing on failure

Pull pstore updates from Kees Cook:
 "Minor changes to pstore tree:

   - update MAINTAINERS with current git repo, add more files.

   - move prz allocation checks into the walker

   - initialize flags correctly (by accident spinlock was technically
     ok)"

* tag 'pstore-v4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  MAINTAINERS: Adjust pstore git repo URI, add files
  pstore: Check for prz allocation in walker
  pstore: Correctly initialize spinlock and flags

Pull HID fix from Jiri Kosina:
 "Regression fix for HID_RMI-driven synaptics touchpads in
  !CONFIG_HID_RMI cases"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: rmi: fallback to generic/multitouch if hid-rmi is not built

Pull libata updates from Tejun Heo:

 - Bartlomiej added pata_falcon

 - Christoph is trying to remove use of static 4k buf.  It's still WIP

 - config cleanup around HAS_DMA

 - other fixes and driver-specific changes

* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (29 commits)
  ata: pata_of_platform: using of_property_read_u32() helper
  pata_atiixp: Don't use unconnected secondary port on SB600/SB700
  libata-sff: Don't scan disabled ports when checking for legacy mode.
  pata_octeon_cf: remove unused local variables from octeon_cf_set_piomode()
  ahci: qoriq: added ls2088a platforms support
  ahci: qoriq: report error when ecc register address is missing in dts
  ahci: qoriq: added a condition to enable dma coherence
  Revert "libata: switch to dynamic allocation instead of ata_scsi_rbuf"
  ahci: imx: fix building without hwmon or thermal
  ata: add Atari Falcon PATA controller driver
  ata: pass queued command to ->sff_data_xfer method
  ata: allow subsystem to be used on m68k arch
  libata: switch to dynamic allocation instead of ata_scsi_rbuf
  libata: don't call ata_scsi_rbuf_fill for command without a response buffer
  libata: call ->scsi_done from ata_scsi_simulate
  libata: remove the done callback from ata_scsi_args
  libata: move struct ata_scsi_args to libata-scsi.c
  libata: avoid global response buffer in atapi_qc_complete
  libata-eh: Use switch() instead of sparse array for protocol strings
  ata: sata_mv: Convert to devm_ioremap_resource()
  ...

Pull dmaengine updates from Vinod Koul:
 "This time we fairly boring and bit small update.

   - Support for Intel iDMA 32-bit hardware
   - deprecate broken support for channel switching in async_tx
   - bunch of updates on stm32-dma
   - Cyclic support for zx dma and making in generic zx dma driver
   - Small updates to bunch of other drivers"

* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
  async_tx: deprecate broken support for channel switching
  dmaengine: rcar-dmac: Widen DMA mask to 40 bits
  dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
  dmaengine: Provide a wrapper for memcpy operations
  dmaengine: zx: fix build warning
  dmaengine: dw: we do support Merrifield SoC in PCI mode
  dmaengine: dw: add support of iDMA 32-bit hardware
  dmaengine: dw: introduce register mappings for iDMA 32-bit
  dmaengine: dw: introduce block2bytes() and bytes2block()
  dmaengine: dw: extract dwc_chan_pause() for future use
  dmaengine: dw: replace convert_burst() with one liner
  dmaengine: dw: register IRQ and DMA pool with instance ID
  dmaengine: dw: Fix data corruption in large device to memory transfers
  dmaengine: ste_dma40: indicate granularity on channels
  dmaengine: ste_dma40: indicate directions on channels
  dmaengine: stm32-dma: Add error messages if xlate fails
  dmaengine: dw: pci: remove LPE Audio DMA ID
  dmaengine: stm32-dma: Add max_burst support
  dmaengine: stm32-dma: Add synchronization support
  dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
  ...

Pull media updates from Mauro Carvalho Chehab:

 - new drivers:
       - i.MX6 Video Data Order Adapter's (VDOA)
       - Toshiba et8ek8 5MP sensor
       - STM DELTA multi-format video decoder V4L2 driver
       - SPI connected IR LED
       - Mediatek IR remote receiver
       - ZyDAS ZD1301 DVB USB interface driver

 - new RC keymaps

 - some very old LIRC drivers got removed from staging

 - RC core gained support encoding IR scan codes

 - DVB si2168 gained support for DVBv5 statistics

 - lirc_sir driver ported to rc-core and promoted from staging

 - other bug fixes, board additions and driver improvements

* tag 'media/v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (230 commits)
  [media] mtk-vcodec: fix build warnings without DEBUG
  [media] zd1301: fix building interface driver without demodulator
  [media] usbtv: add sharpness control
  [media] cxusb: Use a dma capable buffer also for reading
  [media] ttpci: address stringop overflow warning
  [media] dvb-usb-v2: avoid use-after-free
  [media] add Hama Hybrid DVB-T Stick support
  [media] et8ek8: Fix compiler / Coccinelle warnings
  [media] media: fix semicolon.cocci warnings
  [media] media: exynos4-is: add flags to dummy Exynos IS i2c adapter
  [media] v4l: of: check for unique lanes in data-lanes and clock-lanes
  [media] coda/imx-vdoa: constify structs
  [media] st-delta: debug: trace stream/frame information & summary
  [media] st-delta: add mjpeg support
  [media] st-delta: EOS (End Of Stream) support
  [media] st-delta: rpmsg ipc support
  [media] st-delta: add memory allocator helper functions
  [media] st-delta: STiH4xx multi-format video decoder v4l2 driver
  [media] MAINTAINERS: add st-delta driver
  [media] ARM: multi_v7_defconfig: enable STMicroelectronics DELTA Support
  ...

Pull pin control updates from Linus Walleij:
 "Pin control bulk changes for the v4.11 kernel cycle.

  Core changes:

   - Switch the generic pin config argument from 16 to 24 bits, only use
     8 bits for the configuration type. We might need to encode more
     information about a certain setting than we need to encode
     different generic settings.

   - Add a cross-talk API to the pin control GPIO back-end, utilizing
     pinctrl_gpio_set_config() from GPIO drivers that want to set up a
     certain pin configuration in the back-end.

     This also includes the .set_config() refactoring of the GPIO chips,
     so that they pass a generic configuration for things like
     debouncing and single ended (typically open drain). This change has
     also been merged in an immutable branch to the GPIO tree.

   - Take hogs with a delayed work, so that we finalize probing a pin
     controller before trying to get any hogs.

   - For pin controllers putting all group and function definitions into
     the device tree, we now have generic code to deal with this and it
     is used in two drivers so far.

   - Simplifications of the pin request conflict check.

   - Make dt_free_map() optional.

  Updates to drivers:

   - pinctrl-single now use the generic helpers to generate dynamic
     group and function tables from the device tree.

   - Texas Instruments IOdelay configuration driver add-on to
     pinctrl-single.

   - i.MX: use radix trees to store groups and functions, use the new
     generic group and function helpers to manage them.

   - Intel: add support for hardware debouncing and 1K pull-down. New
     subdriver for the Gemini Lake SoC.

   - Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
     MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.

   - Aspeed: use syscon cross-dependencies to set up related bits in the
     LPC host controller and display controller.

   - Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
     Add banks Y, Z, AA, AB and AC.

   - AMD: support additional GPIO.

   - STM32: set this controller to strict muxing mode. STM32H743 MCU
     support.

   - Allwinner sunxi: deep simplifications on how to support subvariants
     of SoCs without adding to much SoC-specific data for each
     subvariant, especially for sun5i variants. New driver for V3s SoCs.
     New driver for the H5 SoC. Support A31/A31s variants with the new
     variant framework.

   - Mvebu: simplifications to use a MMIO and regmap abstraction. New
     subdrivers for the 98DX3236, 98DX5241 SoCs.

   - Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
     driver to access regmaps. Add infrastructure for pin-bank retention
     control. Clean out the pin retention control from
     arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
     the Samsung pin control driver(s).

   - Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.

   - Qualcomm: use raw spinlock variants: this makes the qualcomm driver
     realtime-safe"

* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
  pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
  pinctrl: intel: unlock on error in intel_config_set_pull()
  pinctrl: berlin: make bool drivers explicitly non-modular
  pinctrl: spear: make bool drivers explicitly non-modular
  pinctrl: mvebu: make bool drivers explicitly non-modular
  pinctrl: sunxi: make sun5i explicitly non-modular
  pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
  pinctrl: samsung: mark PM functions as __maybe_unused
  pinctrl: sunxi: Remove redundant A31s pinctrl driver
  pinctrl: sunxi: Support A31/A31s with pinctrl variants
  pinctrl: Amend bindings for STM32 pinctrl
  pinctrl: Add STM32 pinctrl driver DT bindings
  pinctrl: stm32: Add STM32H743 MCU support
  include: dt-bindings: Add STM32H7 pinctrl DT defines
  gpio: aspeed: Remove dependence on GPIOF_* macros
  pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
  drivers: pinctrl: add driver for Allwinner H5 SoC
  pinctrl: intel: Add Intel Gemini Lake pin controller support
  pinctrl: intel: Add support for 1k additional pull-down
  pinctrl: intel: Add support for hardware debouncer
  ...

Commit 279967a6 ("HID: rmi: Handle all Synaptics touchpads using hid-rmi")
unconditionally switches over handling of all Synaptics touchpads to hid-rmi
(to make use of extended features of the HW); in case CONFIG_HID_RMI is
disabled though this renders the touchpad unusable, as the

	HID_DEVICE(HID_BUS_ANY, HID_GROUP_RMI, HID_ANY_ID, HID_ANY_ID)

match doesn't exist and generic/multitouch doesn't bind to it either (due
to hid group mismatch).

Fix this by switching over to hid-rmi only if it has been actually built.

Fixes: 279967a6 ("HID: rmi: Handle all Synaptics touchpads using hid-rmi")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull exception table module split from Paul Gortmaker:
 "Final extable.h related changes.

  This completes the separation of exception table content from the
  module.h header file. This is achieved with the final commit that
  removes the one line back compatible change that sourced extable.h
  into the module.h file.

  The commits are unchanged since January, with the exception of a
  couple Acks that came in for the last two commits a bit later. The
  changes have been in linux-next for quite some time[1] and have got
  widespread arch coverage via toolchains I have and also from
  additional ones the kbuild bot has.

  Maintaners of the various arch were Cc'd during the postings to
  lkml[2] and informed that the intention was to take the remaining arch
  specific changes and lump them together with the final two non-arch
  specific changes and submit for this merge window.

  The ia64 diffstat stands out and probably warrants a mention. In an
  earlier review, Al Viro made a valid comment that the original header
  separation of content left something to be desired, and that it get
  fixed as a part of this change, hence the larger diffstat"

* tag 'extable-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (21 commits)
  module.h: remove extable.h include now users have migrated
  core: migrate exception table users off module.h and onto extable.h
  cris: migrate exception table users off module.h and onto extable.h
  hexagon: migrate exception table users off module.h and onto extable.h
  microblaze: migrate exception table users off module.h and onto extable.h
  unicore32: migrate exception table users off module.h and onto extable.h
  score: migrate exception table users off module.h and onto extable.h
  metag: migrate exception table users off module.h and onto extable.h
  arc: migrate exception table users off module.h and onto extable.h
  nios2: migrate exception table users off module.h and onto extable.h
  sparc: migrate exception table users onto extable.h
  openrisc: migrate exception table users off module.h and onto extable.h
  frv: migrate exception table users off module.h and onto extable.h
  sh: migrate exception table users off module.h and onto extable.h
  xtensa: migrate exception table users off module.h and onto extable.h
  mn10300: migrate exception table users off module.h and onto extable.h
  alpha: migrate exception table users off module.h and onto extable.h
  arm: migrate exception table users off module.h and onto extable.h
  m32r: migrate exception table users off module.h and onto extable.h
  ia64: ensure exception table search users include extable.h
  ...

Pull MIPS updates from James Hogan:
 "Here's the main MIPS pull request for 4.11.

  It contains a few new features such as IRQ stacks, cacheinfo support,
  and KASLR for Octeon CPUs, and a variety of smaller improvements and
  fixes including devicetree additions, kexec cleanups, microMIPS stack
  unwinding fixes, and a bunch of build fixes to clean up continuous
  integration builds.

  Its all been in linux-next for at least a couple of days, most of it
  far longer.

  Miscellaneous:
   - Add IRQ stacks
   - Add cacheinfo support
   - Add "uzImage.bin" zboot target
   - Unify performance counter definitions
   - Export various (mainly assembly) symbols alongside their
     definitions
   - Audit and remove unnecessary uses of module.h

  kexec & kdump:
   - Lots of improvements and fixes
   - Add correct copy_regs implementations
   - Add debug logging of new kernel information

  Security:
   - Use Makefile.postlink to insert relocations into vmlinux
   - Provide plat_post_relocation hook (used for Octeon KASLR)
   - Add support for tuning mmap randomisation
   - Relocate DTB

  microMIPS:
   - A load of unwind fixes
   - Add some missing .insn to fix link errors

  MIPSr6:
   - Fix MULTU/MADDU/MSUBU sign extension in r2 emulation
   - Remove r2_emul_return and use ERETNC unconditionally on MIPSr6
   - Allow pre-r6 emulation on SMP MIPSr6 kernels

  Cache management:
   - Treat physically indexed dcache as non-aliasing
   - Add return errors to protected cache ops for KVM
   - CM3: Ensure L1 & L2 cache ECC checking matches
   - CM3: Indicate inclusive caches
   - I6400: Treat dcache as physically indexed

  Memory management:
   - Ensure bootmem doesn't corrupt reserved memory
   - Export some TLB exception generation functions for KVM

  OF:
   - NULL check initial_boot_params before use in of_scan_flat_dt()
   - Fix unaligned access in of_alias_scan()

  SMP:
   - CPS: Don't BUG if a CPU fails to start

  Other fixes:
   - Fix longstanding 64-bit IP checksum carry bug
   - Fix KERN_CONT fallout in cpu-bugs64.c and sync-r4k.c
   - Update defconfigs for NF_CT_PROTO_DCCP, DPLITE,
     CPU_FREQ_STAT,SCSI_DH changes
   - Disable certain builtin compiler options, stack-check (whole
     kernel), asynchronous-unwind-tables (VDSO).
   - A bunch of build fixes from kernelci.org testing
   - Various other minor cleanups & corrections

  BMIPS:
   - Migrate interrupts during bmips_cpu_disable
   - BCM47xx: Add Luxul devices
   - BCM47xx: Fix Asus WL-500W button inversion
   - BCM7xxx: Add SPI device nodes

  Generic (multiplatform):
   - Add kexec DTB passing
   - Fix big endian
   - Add cpp_its_S in ksym_dep_filter to silence build warning

  IP22:
   - Reformat inline assembler code to modern standards
   - Fix binutils 2.25 build error

  IP27:
   - Fix duplicate CAC_BASE definition build error
   - Disable qlge driver to workaround broken compiler

  Lantiq:
   - Refresh defconfig and activate more drivers
   - Lock DMA register access
   - Fix cascading IRQ setup
   - Fix build of VPE loader
   - xway: Fix ethernet packet header corruption over reboot

  Loongson1
   - Add watchdog support
   - 1B: Reduce DEFAULT_MEMSIZE to 64MB
   - 1B: Change OSC clock name to match rest of kernel
   - 1C: Remove ARCH_WANT_OPTIONAL_GPIOLIB

  Octeon:
   - Add KASLR support
   - Support Octeon III USB controller
   - Fix large copy_from_user corner case
   - Enable devtmpfs in defconfig

  Netlogic:
   - Fix non-default XLR build error due to netlogic,xlp-pic code
   - Fix assembler warning from smpboot.S

  pic32mzda:
   - Fix linker error when early printk is disabled

  Pistachio:
   - Add base device tree
   - Add Ci40 "Marduk" device tree

  Ralink:
   - Support raw appended DTB
   - Add missing I2C & I2S clocks
   - Add missing pinmux and fix pinmux function name typo
   - Add missing clk_round_rate()
   - Clean up prom_init()
   - MT7621: Set SoC type
   - MT7621: Support highmem

  TXx9:
   - Modernize printing of kernel messages and resolve KERN_CONT fallout
   - 7segled: use permission-specific DEVICE_ATTR variants

  XilFPGA:
   - Add IRQ controller and UART IRQ
   - Add AXI I2C and emaclite to DT & defconfig"

* tag 'mips_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (148 commits)
  MIPS: VDSO: Explicitly use -fno-asynchronous-unwind-tables
  MIPS: BCM47XX: Fix button inversion for Asus WL-500W
  MIPS: DTS: Add img directory to Makefile
  MIPS: ip27: Disable qlge driver in defconfig
  MIPS: pic32mzda: Fix linker error for pic32_get_pbclk()
  MIPS: Lantiq: Keep ethernet enabled during boot
  MIPS: OCTEON: Fix copy_from_user fault handling for large buffers
  MIPS: Fix special case in 64 bit IP checksumming.
  MIPS: OCTEON: Enable DEVTMPFS
  MIPS: lantiq: Set physical_memsize
  MIPS: sysmips: Remove duplicated include from syscall.c
  Kbuild: Add cpp_its_S in ksym_dep_filter
  MIPS: Audit and remove any unnecessary uses of module.h
  MIPS: Unify perf counter register definitions
  MIPS: Disable stack checks on MIPS kernels
  MIPS: OCTEON: Platform support for OCTEON III USB controller
  MIPS: Lantiq: Fix cascaded IRQ setup
  MIPS: sync-r4k: Fix KERN_CONT fallout
  MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch
  MIPS: Fix distclean with Makefile.postlink
  ...

Pull xen updates from Juergen Gross:
 "Xen features and fixes:

   - a series from Boris Ostrovsky adding support for booting Linux as
     Xen PVH guest

   - a series from Juergen Gross streamlining the xenbus driver

   - a series from Paul Durrant adding support for the new device model
     hypercall

   - several small corrections"

* tag 'for-linus-4.11-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/privcmd: add IOCTL_PRIVCMD_RESTRICT
  xen/privcmd: Add IOCTL_PRIVCMD_DM_OP
  xen/privcmd: return -ENOTTY for unimplemented IOCTLs
  xen: optimize xenbus driver for multiple concurrent xenstore accesses
  xen: modify xenstore watch event interface
  xen: clean up xenbus internal headers
  xenbus: Neaten xenbus_va_dev_error
  xen/pvh: Use Xen's emergency_restart op for PVH guests
  xen/pvh: Enable CPU hotplug
  xen/pvh: PVH guests always have PV devices
  xen/pvh: Initialize grant table for PVH guests
  xen/pvh: Make sure we don't use ACPI_IRQ_MODEL_PIC for SCI
  xen/pvh: Bootstrap PVH guest
  xen/pvh: Import PVH-related Xen public interfaces
  xen/x86: Remove PVH support
  x86/boot/32: Convert the 32-bit pgtable setup code from assembly to C
  xen/manage: correct return value check on xenbus_scanf()
  x86/xen: Fix APIC id mismatch warning on Intel
  xen/netback: set default upper limit of tx/rx queues to 8
  xen/netfront: set default upper limit of tx/rx queues to 8

Pull audit updates from Paul Moore:
 "The audit changes for v4.11 are relatively small compared to what we
  did for v4.10, both in terms of size and impact.

   - two patches from Steve tweak the formatting for some of the audit
     records to make them more consistent with other audit records.

   - three patches from Richard record the name of a module on module
     load, fix the logging of sockaddr information when using
     socketcall() on 32-bit systems, and add the ability to reset
     audit's lost record counter.

   - my lone patch just fixes an annoying style nit that I was reminded
     about by one of Richard's patches.

  All these patches pass our test suite"

* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
  audit: remove unnecessary curly braces from switch/case statements
  audit: log module name on init_module
  audit: log 32-bit socketcalls
  audit: add feature audit_lost reset
  audit: Make AUDIT_ANOM_ABEND event normalized
  audit: Make AUDIT_KERNEL event conform to the specification

This reverts commit f2593cb1.

Paul reported that this patch with older board-2.bin ath10k initialisation
fails on Dell XPS 13:

ath10k_pci 0000:3a:00.0: failed to fetch board data for bus=pci,vendor=168c,
device=003e,subsystem-vendor=1a56,subsystem-device=1535,variant=RV_0520 from
ath10k/QCA6174/hw3.0/board-2.bin

The reason is that the older board-2.bin does not have the variant version of
the image name and ath10k does not fallback to the older naming scheme.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=185621#c9
Fixes: f2593cb1 ("ath10k: Search SMBIOS for OEM board file extension")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull security layer updates from James Morris:
 "Highlights:

   - major AppArmor update: policy namespaces & lots of fixes

   - add /sys/kernel/security/lsm node for easy detection of loaded LSMs

   - SELinux cgroupfs labeling support

   - SELinux context mounts on tmpfs, ramfs, devpts within user
     namespaces

   - improved TPM 2.0 support"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (117 commits)
  tpm: declare tpm2_get_pcr_allocation() as static
  tpm: Fix expected number of response bytes of TPM1.2 PCR Extend
  tpm xen: drop unneeded chip variable
  tpm: fix misspelled "facilitate" in module parameter description
  tpm_tis: fix the error handling of init_tis()
  KEYS: Use memzero_explicit() for secret data
  KEYS: Fix an error code in request_master_key()
  sign-file: fix build error in sign-file.c with libressl
  selinux: allow changing labels for cgroupfs
  selinux: fix off-by-one in setprocattr
  tpm: silence an array overflow warning
  tpm: fix the type of owned field in cap_t
  tpm: add securityfs support for TPM 2.0 firmware event log
  tpm: enhance read_log_of() to support Physical TPM event log
  tpm: enhance TPM 2.0 PCR extend to support multiple banks
  tpm: implement TPM 2.0 capability to get active PCR banks
  tpm: fix RC value check in tpm2_seal_trusted
  tpm_tis: fix iTPM probe via probe_itpm() function
  tpm: Begin the process to deprecate user_read_timer
  tpm: remove tpm_read_index and tpm_write_index from tpm.h
  ...

Add git tree url for modules.
Signed-off-by: Jessica Yu <jeyu@redhat.com>

While looking for early possible module loading failures I was
able to reproduce a memory leak possible with kmemleak. There
are a few rare ways to trigger a failure:

  o we've run into a failure while processing kernel parameters
    (parse_args() returns an error)
  o mod_sysfs_setup() fails
  o we're a live patch module and copy_module_elf() fails

Chances of running into this issue is really low.

kmemleak splat:

unreferenced object 0xffff9f2c4ada1b00 (size 32):
  comm "kworker/u16:4", pid 82, jiffies 4294897636 (age 681.816s)
  hex dump (first 32 bytes):
    6d 65 6d 73 74 69 63 6b 30 00 00 00 00 00 00 00  memstick0.......
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8c6cfeba>] kmemleak_alloc+0x4a/0xa0
    [<ffffffff8c200046>] __kmalloc_track_caller+0x126/0x230
    [<ffffffff8c1bc581>] kstrdup+0x31/0x60
    [<ffffffff8c1bc5d4>] kstrdup_const+0x24/0x30
    [<ffffffff8c3c23aa>] kvasprintf_const+0x7a/0x90
    [<ffffffff8c3b5481>] kobject_set_name_vargs+0x21/0x90
    [<ffffffff8c4fbdd7>] dev_set_name+0x47/0x50
    [<ffffffffc07819e5>] memstick_check+0x95/0x33c [memstick]
    [<ffffffff8c09c893>] process_one_work+0x1f3/0x4b0
    [<ffffffff8c09cb98>] worker_thread+0x48/0x4e0
    [<ffffffff8c0a2b79>] kthread+0xc9/0xe0
    [<ffffffff8c6dab5f>] ret_from_fork+0x1f/0x40
    [<ffffffffffffffff>] 0xffffffffffffffff

Cc: stable <stable@vger.kernel.org> # v2.6.30
Fixes: e180a6b7 ("param: fix charp parameters set via sysfs")
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Jessica Yu <jeyu@redhat.com>

Pull device mapper updates from Mike Snitzer:

 - Fix dm-raid transient device failure processing and other smaller
   tweaks.

 - Add journal support to the DM raid target to close the 'write hole'
   on raid 4/5/6.

 - Fix dm-cache corruption, due to rounding bug, when cache exceeds 2TB.

 - Add 'metadata2' feature to dm-cache to separate the dirty bitset out
   from other cache metadata. This improves speed of shutting down a
   large cache device (which implies writing out dirty bits).

 - Fix a memory leak during dm-stats data structure destruction.

 - Fix a DM multipath round-robin path selector performance regression
   that was caused by less precise balancing across all paths.

 - Lastly, introduce a DM core fix for a long-standing DM snapshot
   deadlock that is rooted in the complexity of the device stack used in
   conjunction with block core maintaining bios on current->bio_list to
   manage recursion in generic_make_request(). A more comprehensive fix
   to block core (and its hook in the cpu scheduler) would be wonderful
   but this DM-specific fix is pragmatic considering how difficult it
   has been to make progress on a generic fix.

* tag 'dm-4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (22 commits)
  dm: flush queued bios when process blocks to avoid deadlock
  dm round robin: revert "use percpu 'repeat_count' and 'current_path'"
  dm stats: fix a leaked s->histogram_boundaries array
  dm space map metadata: constify dm_space_map structures
  dm cache metadata: use cursor api in blocks_are_clean_separate_dirty()
  dm persistent data: add cursor skip functions to the cursor APIs
  dm cache metadata: use dm_bitset_new() to create the dirty bitset in format 2
  dm bitset: add dm_bitset_new()
  dm cache metadata: name the cache block that couldn't be loaded
  dm cache metadata: add "metadata2" feature
  dm cache metadata: use bitset cursor api to load discard bitset
  dm bitset: introduce cursor api
  dm btree: use GFP_NOFS in dm_btree_del()
  dm space map common: memcpy the disk root to ensure it's arch aligned
  dm block manager: add unlikely() annotations on dm_bufio error paths
  dm cache: fix corruption seen when using cache > 2TB
  dm raid: cleanup awkward branching in raid_message() option processing
  dm raid: use mddev rather than rdev->mddev
  dm raid: use read_disk_sb() throughout
  dm raid: add raid4/5/6 journaling support
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for Marvell SD8787 Wifi/BT chip
   - Improve UHS support for SDIO
   - Invent MMC_CAP_3_3V_DDR and a DT binding for eMMC DDR 3.3V mode
   - Detect Auto BKOPS enable bit
   - Export eMMC device lifetime information through sysfs
   - First take to slim down the public mmc headers to avoid abuse
   - Re-factoring of the mmc block device driver to prepare for blkmq
   - Cleanup code for the mmc block device driver
   - Clarify and cleanup code dealing with data requests
   - Cleanup some code by converting to ida_simple_ functions
   - Cleanup code dealing with card quirks
   - Cleanup private and public mmc header files

  MMC host:
   - Don't rely on public mmc headers to include non-mmc related headers
   - meson: Add support for eMMC HS400 mode
   - meson: Various cleanups and improvements
   - omap_hsmmc: Use the proper provided busy timeout from the core
   - sunxi: Enable new timings for the A64 MMC controllers
   - sunxi: Improvements for clock management
   - tmio: Improvements for SDIO interrupts
   - mxs-mmc: Add CMD23 support
   - sdhci-msm: Enable HS400 enhanced strobe mode support
   - sdhci-msm: Correct HS400 tuning sequence
   - sdhci-acpi: Support deferred probe
   - sdhci-pci: Add support for eMMC HS200 tuning mode on AMD
   - mediatek: Correct the implementation of card busy detection
   - dw_mmc: Initial support for ZX mmc controller
   - sh_mobile_sdhi: Enable support for eMMC HS200 mode
   - sh_mmcif: Various cleanups and improvements"

* tag 'mmc-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (145 commits)
  mmc: core: add mmc prefix for blk_fixups
  mmc: core: move all quirks together into quirks.h
  mmc: core: improve the quirks for sdio devices
  mmc: core: move some sdio IDs out of quirks file
  mmc: core: change quirks.c to be a header file
  mmc: sdhci-cadence: fix bit shift of read data from PHY port
  mmc: Adding AUTO_BKOPS_EN bit set for Auto BKOPS support
  mmc: MAN_BKOPS_EN inverse debug message logic
  mmc: meson-gx: add support for HS400 mode
  mmc: meson-gx: remove unneeded checks in remove
  mmc: meson-gx: reduce bounce buffer size
  mmc: meson-gx: set max block count and request size
  mmc: meson-gx: improve interrupt handling
  mmc: meson-gx: improve meson_mmc_irq_thread
  mmc: meson-gx: improve meson_mmc_clk_set
  mmc: meson-gx: minor improvements in meson_mmc_set_ios
  mmc: meson: Assign the minimum clk rate as close to 400KHz as possible
  mmc: core: start to break apart mmc_start_areq()
  mmc: block: respect bool returned from blk_end_request()
  mmc: block: return errorcode from mmc_sd_num_wr_blocks()
  ...

The existing test was only exercising native unsigned long size
get_user(). For completeness, we should check all sizes. But we
must skip some 32-bit architectures that don't implement a 64-bit
get_user().

These new tests actually uncovered a bug in ARM's 64-bit get_user()
zeroing.
Signed-off-by: Kees Cook <keescook@chromium.org>

Pull SCSI updates from James Bottomley:
 "This update includes the usual round of major driver updates (ncr5380,
  ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
  megaraid_sas, ...).

  There's also an assortment of minor fixes and the major update of
  switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
  scsi: megaraid_sas: handle dma_addr_t right on 32-bit
  scsi: megaraid_sas: array overflow in megasas_dump_frame()
  scsi: snic: switch to pci_irq_alloc_vectors
  scsi: megaraid_sas: driver version upgrade
  scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
  scsi: megaraid_sas: Indentation and smatch warning fixes
  scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
  scsi: megaraid_sas: Increase internal command pool
  scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
  scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
  scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
  scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
  scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
  scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
  scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
  scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
  scsi: megaraid_sas: update can_queue only if the new value is less
  scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
  scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
  scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
  ...

Pull block layer updates from Jens Axboe:

 - blk-mq scheduling framework from me and Omar, with a port of the
   deadline scheduler for this framework. A port of BFQ from Paolo is in
   the works, and should be ready for 4.12.

 - Various fixups and improvements to the above scheduling framework
   from Omar, Paolo, Bart, me, others.

 - Cleanup of the exported sysfs blk-mq data into debugfs, from Omar.
   This allows us to export more information that helps debug hangs or
   performance issues, without cluttering or abusing the sysfs API.

 - Fixes for the sbitmap code, the scalable bitmap code that was
   migrated from blk-mq, from Omar.

 - Removal of the BLOCK_PC support in struct request, and refactoring of
   carrying SCSI payloads in the block layer. This cleans up the code
   nicely, and enables us to kill the SCSI specific parts of struct
   request, shrinking it down nicely. From Christoph mainly, with help
   from Hannes.

 - Support for ranged discard requests and discard merging, also from
   Christoph.

 - Support for OPAL in the block layer, and for NVMe as well. Mainly
   from Scott Bauer, with fixes/updates from various others folks.

 - Error code fixup for gdrom from Christophe.

 - cciss pci irq allocation cleanup from Christoph.

 - Making the cdrom device operations read only, from Kees Cook.

 - Fixes for duplicate bdi registrations and bdi/queue life time
   problems from Jan and Dan.

 - Set of fixes and updates for lightnvm, from Matias and Javier.

 - A few fixes for nbd from Josef, using idr to name devices and a
   workqueue deadlock fix on receive. Also marks Josef as the current
   maintainer of nbd.

 - Fix from Josef, overwriting queue settings when the number of
   hardware queues is updated for a blk-mq device.

 - NVMe fix from Keith, ensuring that we don't repeatedly mark and IO
   aborted, if we didn't end up aborting it.

 - SG gap merging fix from Ming Lei for block.

 - Loop fix also from Ming, fixing a race and crash between setting loop
   status and IO.

 - Two block race fixes from Tahsin, fixing request list iteration and
   fixing a race between device registration and udev device add
   notifiations.

 - Double free fix from cgroup writeback, from Tejun.

 - Another double free fix in blkcg, from Hou Tao.

 - Partition overflow fix for EFI from Alden Tondettar.

* tag 'for-4.11/linus-merge-signed' of git://git.kernel.dk/linux-block: (156 commits)
  nvme: Check for Security send/recv support before issuing commands.
  block/sed-opal: allocate struct opal_dev dynamically
  block/sed-opal: tone down not supported warnings
  block: don't defer flushes on blk-mq + scheduling
  blk-mq-sched: ask scheduler for work, if we failed dispatching leftovers
  blk-mq: don't special case flush inserts for blk-mq-sched
  blk-mq-sched: don't add flushes to the head of requeue queue
  blk-mq: have blk_mq_dispatch_rq_list() return if we queued IO or not
  block: do not allow updates through sysfs until registration completes
  lightnvm: set default lun range when no luns are specified
  lightnvm: fix off-by-one error on target initialization
  Maintainers: Modify SED list from nvme to block
  Move stack parameters for sed_ioctl to prevent oversized stack with CONFIG_KASAN
  uapi: sed-opal fix IOW for activate lsp to use correct struct
  cdrom: Make device operations read-only
  elevator: fix loading wrong elevator type for blk-mq devices
  cciss: switch to pci_irq_alloc_vectors
  block/loop: fix race between I/O and set_status
  blk-mq-sched: don't hold queue_lock when calling exit_icq
  block: set make_request_fn manually in blk_mq_update_nr_hw_queues
  ...

Commit 004172bd ("sched/core: Remove unnecessary #include headers")
removed the inclusion of asm/paravirt.h which is used to get
declarations of paravirt_steal_rq_enabled and paravirt_steal_clock.

It is implicitly included on x86 but not on arm and arm64 breaking the
build if paravirtualization is used.  Since things from that header are
used directly fix the build by putting the direct inclusion back.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 34b88a68 ("net: Fix use after free in the recvmmsg exit path"),
changed the exit path of recvmmsg to always return the datagrams
variable and modified the error paths to set the variable to the error
code returned by recvmsg if necessary.

However in the case sock_error returned an error, the error code was
then ignored, and recvmmsg returned 0.

Change the error path of recvmmsg to correctly return the error code
of sock_error.

The bug was triggered by using recvmmsg on a CAN interface which was
not up. Linux 4.6 and later return 0 in this case while earlier
releases returned -ENETDOWN.

Fixes: 34b88a68 ("net: Fix use after free in the recvmmsg exit path")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>