Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Certain USB devices, such as the Nokia X6 mobile phone, don't expose any
endpoint descriptors on some of their interfaces. If the ACM driver is forced
to probe all interfaces on a device the a NULL pointer dereference will occur
when the ACM driver attempts to use the endpoint of the alternative settings.
One way to get the ACM driver to probe all the interfaces is by using the
/sys/bus/usb/drivers/cdc_acm/new_id interface.

This patch checks that the endpoint pointer for the current alternate settings
is non-NULL before using it.
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

cdc-acm.c : Manage pseudo-modem without AT commands capabilities
  Enable to drive electronic simple gadgets based on microcontrolers.
  The Interface descriptor is like this:
    bInterfaceClass         2 Communications
    bInterfaceSubClass      2 Abstract (modem)
    bInterfaceProtocol      0 None
Signed-off-by: Philippe Corbes <philippe.corbes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The command endpoint is either a bulk or interrupt endpoint, but using
the wrong type of transfer causes an error if CONFIG_USB_DEBUG is
enabled after commit f661c6f8, which
checks for this mismatch.

Detect which type of endpoint it is and use a bulk/int URB as
appropriate. There are other function calls specifying a bulk pipe,
but usb_clear_halt doesn't use the pipe type (only the endpoint) and
usb_bulk_msg auto-detects interrupt transfers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable <stable@kernel.org> [.34 and newer]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P.  This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

S60 phones from Nokia and Samsung expose two ACM channels. The first is a modem
with a standard AT-command interface, which is picked up correctly by CDC-ACM.

The second ACM port is marked as having a vendor-specific protocol. This means
that the ACM driver will not claim the second channel by default.

This adds support for the second ACM channel for the following devices:
    Nokia E63
    Nokia E75
    Nokia 6760 Slide
    Nokia E52
    Nokia E55
    Nokia E72
    Nokia X6
    Nokia N97 Mini
    Nokia 5800 Xpressmusic
    Nokia E90
    Samsung GTi8510 (INNOV8)
Signed-off-by: Toby Gray <toby.gray@realvnc.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Remove the hard coding of the debug flag to 1.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When using the remove sysfs file, the device configuration is set to -1
(unconfigured). This eventually unbind drivers with the bandwidth_mutex
held. Some drivers may call functions that hold said mutex, like
usb_reset_device. This is the case for rtl8187, for example. This will
lead to the same process holding the mutex twice, which deadlocks.

Besides, according to Alan Stern:
"The deadlock problem probably could be handled somehow, but there's a
separate issue: Until the usb_disable_device call finishes unbinding
the drivers, the drivers are free to continue using their allocated
bandwidth.  We musn't change the bandwidth allocations until after the
unbinding is done.  So this patch is indeed necessary."

Unbinding the driver before holding the bandwidth_mutex solves the
problem. If any operation after that fails, drivers are not bound again.
But that would be a problem anyway that the user may solve resetting the
device configuration to one that works, just like he would need to do in
most other failure cases.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0489 Foxconn / Hon Hai
  idProduct          0xe000 T-Com TC 300
  bcdDevice            1.00
  iManufacturer           1 Silicon Labs
  iProduct                2 TC 300
  iSerial                 3 0001
    [snip]
---------------------------------------------------------------------------

However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x0489 Foxconn / Hon Hai
  idProduct          0xe003 Pirelli DP-L10
  bcdDevice            1.00
  iManufacturer           1 Silicon Labs
  iProduct                2 DP-L10
  iSerial                 3 0001
    [snip]
-------------------------------------------------------------------------

All that is required is an extra USB_DEVICE entry:

{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */

The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is the cable between an H3000 navigation unit and a multi-function display.
http://www.bandg.com/en/Products/H3000/Spares-and-Accessories/Cables/H3000-CPU-USB-Cable-Pack/Signed-off-by: Jason Detring <jason.detring@navico.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.

Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Please find attached patch for
https://bugzilla.kernel.org/show_bug.cgi?id=16023 problem.
Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch removes the following section mismatch warning,
by moving the function rndis_init() from .init.text to .text.

WARNING: vmlinux.o(.text+0x1aeca5a): Section mismatch in reference from the function rndis_bind_config() to the function .init.text:rndis_init()
The function rndis_bind_config() references
the function __init rndis_init().
This is often because rndis_bind_config lacks a __init
annotation or the annotation of rndis_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The iounmap(ehci->ohci_hcctrl_reg); should be the first thing we do
because the ioremap() was the last thing we did.  Also if we hit any of
the goto statements in the original code then it would have led to a
NULL dereference of "ehci".  This bug was introduced in: 796bcae7
"USB: powerpc: Workaround for the PPC440EPX USBH_23 errata [take 3]"

I modified the few lines in front a little so that my code didn't
obscure the return success code path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

DEBUG is defined unconditionally, remove it as this clutters the message log.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: work around VIA and NEC PHY packet reception bug
  firewire: core: do not use del_timer_sync() in interrupt context
  firewire: net: fix unicast reception RCODE in failure paths
  firewire: sbp2: fix stall with "Unsolicited response"
  firewire: sbp2: fix memory leak in sbp2_cancel_orbs or at send error
  ieee1394: Adjust confusing if indentation

VIA VT6306, VIA VT6308, and NEC OrangeLink controllers do not write
packet event codes for received PHY packets (or perhaps write
evt_no_status, hard to tell).  Work around it by overwriting the
packet's ACK by ack_complete, so that upper layers that listen to PHY
packet reception get to see these packets.

(Also tested:  TI TSB82AA2, TI TSB43AB22/A, TI XIO2213A, Agere FW643,
JMicron JMB381 --- these do not exhibit this bug.)

Clemens proposed a quirks flag for that, IOW whitelist known misbehaving
controllers for this workaround.  Though to me it seems harmless enough
to enable for all controllers.

The log_ar_at_event() debug log will continue to show the original
status from the DMA unit.

Reported-by: Clemens Ladisch <clemens@ladisch.de> (VT6308)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  net/ipv4: Eliminate kstrdup memory leak
  net/caif/cfrfml.c: use asm/unaligned.h
  ax25: missplaced sock_put(sk)
  qlge: reset the chip before freeing the buffers
  l2tp: test for ethernet header in l2tp_eth_dev_recv()
  tcp: select(writefds) don't hang up when a peer close connection
  tcp: fix three tcp sysctls tuning
  tcp: Combat per-cpu skew in orphan tests.
  pxa168_eth: silence gcc warnings
  pxa168_eth: update call to phy_mii_ioctl()
  pxa168_eth: fix error handling in prope
  pxa168_eth: remove unneeded null check
  phylib: Fix race between returning phydev and calling adjust_link
  caif-driver: add HAS_DMA dependency
  3c59x: Fix deadlock between boomerang_interrupt and boomerang_start_tx
  qlcnic: fix poll implementation
  netxen: fix poll implementation
  bridge: netfilter: fix a memory leak

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
  Blackfin: bf52x/bf54x boards: drop unused nand page size
  Blackfin: punt duplicate SPORT MMR defines

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: pcm: add more format names
  sound: oss: fix uninitialized spinlock
  ALSA: asihpi - Return hw error directly from oustream_write.
  ASoC: soc-core: fix debugfs_pop_time file permissions
  ALSA: hda - Add Sony VAIO quirk for ALC269

Merge branch 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: S5PV310: Fix on Secondary CPU startup
  ARM: S5PV310: Bug fix on uclk1 and sclk_pwm
  ARM: S5PV310: Fix missed uart clocks
  ARM: S5PV310: Should be clk_sclk_apll not clk_mout_apll
  ARM: S5PV310: Fix on PLL setting for S5PV310
  ARM: S5PV310: Add CMU block for S5PV310 Clock
  ARM: S5PV310: Fix on typo irqs.h of S5PV310
  ARM: S5PV310: Fix on default ZRELADDR of ARCH_S5PV310
  ARM: S5PV310: Fix on GPIO base addresses
  ARM: SAMSUNG: Fix on build warning regarding VMALLOC_END type
  ARM: S5P: VMALLOC_END should be unsigned long

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  fsnotify: drop two useless bools in the fnsotify main loop
  fsnotify: fix list walk order
  fanotify: Return EPERM when a process is not privileged
  fanotify: resize pid and reorder structure
  fanotify: drop duplicate pr_debug statement
  fanotify: flush outstanding perm requests on group destroy
  fsnotify: fix ignored mask handling between inode and vfsmount marks
  fanotify: add MAINTAINERS entry
  fsnotify: reset used_inode and used_vfsmount on each pass
  fanotify: do not dereference inode_mark when it is unset

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  eCryptfs: Fix encrypted file name lookup regression
  ecryptfs: properly mark init functions
  fs/ecryptfs: Return -ENOMEM on memory allocation failure

* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
  arm: tegra: VMALLOC_END should be unsigned long
  arm: tegra: fix compilation of board-harmony.c

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB
  drm/radeon/kms: add missing scratch update in dp_detect
  drm/modes: Fix CVT-R modeline generation
  drm: fix regression in drm locking since BKL removal.
  drm/radeon/kms: remove stray radeon_i2c_destroy
  drm: mm: fix range restricted allocations
  drm/nouveau: drop drm_global_mutex before sleeping in submission path
  drm: export drm_global_mutex for drivers to use
  drm/nv20: Don't use pushbuf calls on the original nv20.
  drm/nouveau: Fix TMDS on some DCB1.5 boards.
  drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
  drm/nv30: Apply modesetting to the correct slave encoder
  drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
  drm/nv50: add dcb type 14 to enum to prevent compiler complaint

* 'lguest' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  lguest: Odd Fixes
  lguest: clean up warnings in demonstration launcher.

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP3: PM: ensure IO wakeups are properly disabled
  omap: Fix omap_4430sdp_defconfig for make oldconfig
  omap: Use CONFIG_SMP for test_for_ipi and test_for_ltirq
  omap: Fix sev instruction usage for multi-omap
  OMAP3: Fix a cpu type check problem
  omap3: id: fix 3630 rev detection

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: fix get_ticket_handler() error handling
  ceph: don't BUG on ENOMEM during mds reconnect
  ceph: ceph_mdsc_build_path() returns an ERR_PTR
  ceph: Fix warnings
  ceph: ceph_get_inode() returns an ERR_PTR
  ceph: initialize fields on new dentry_infos
  ceph: maintain i_head_snapc when any caps are dirty, not just for data
  ceph: fix osd request lru adjustment when sending request
  ceph: don't improperly set dir complete when holding EXCL cap
  mm: exporting account_page_dirty
  ceph: direct requests in snapped namespace based on nonsnap parent
  ceph: queue cap snap writeback for realm children on snap update
  ceph: include dirty xattrs state in snapped caps
  ceph: fix xattr cap writeback
  ceph: fix multiple mds session shutdown

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM QoS: Fix inline documentation.
  PM QoS: Fix kzalloc() parameters swapped in pm_qos_power_open()

* 'for-2.6.36' of git://linux-nfs.org/~bfields/linux:
  nfsd: fix NULL dereference in nfsd_statfs()
  nfsd4: fix downgrade/lock logic
  nfsd4: typo fix in find_any_file
  nfsd4: bad BUG() in preprocess_stateid_op

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  Cannot allocate memory error on mount
  [CIFS] Eliminate unused variable warning

Fix a comma that got accidentally deleted from sys_osf_statfs() leading to the
following warning:

  arch/alpha/kernel/osf_sys.c: In function 'SYSC_osf_statfs':
  arch/alpha/kernel/osf_sys.c:255: error: syntax error before 'buffer'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Stub out vm_get_page_prot() if there's no MMU.

This was added by commit 804af2cf ("[AGPGART] remove private page
protection map") and is used in commit c07fbfd1 ("fbmem: VM_IO set,
but not propagated") in the fbmem video driver, but the function doesn't
exist on NOMMU, resulting in an undefined symbol at link time.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Do not report error overflow as a separate error
  MCE, AMD: Limit MCE decoding to current families for now

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: pxa27x_keypad - remove input_free_device() in pxa27x_keypad_remove()
  Input: mousedev - fix regression of inverting axes
  Input: uinput - add devname alias to allow module on-demand load
  Input: hil_kbd - fix compile error
  USB: drop tty argument from usb_serial_handle_sysrq_char()
  Input: sysrq - drop tty argument form handle_sysrq()
  Input: sysrq - drop tty argument from sysrq ops handlers

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-sff: remove harmful BUG_ON from ata_bmdma_qc_issue
  sata_mv: fix broken DSM/TRIM support (v2)
  libata: be less of a drama queen on empty data commands
  [libata] sata_dwc_460ex: signdness bug
  ahci: add HFLAG_YES_FBS and apply it to 88SE9128
  libata: remove no longer needed pata_winbond driver
  pata_cmd64x: revert commit d62f5576

After several hours, kbuild tests hang with anon_vma_prepare() spinning on
a newly allocated anon_vma's lock - on a box with CONFIG_TREE_PREEMPT_RCU=y
(which makes this very much more likely, but it could happen without).

The ever-subtle page_lock_anon_vma() now needs a further twist: since
anon_vma_prepare() and anon_vma_fork() are liable to change the ->root
of a reused anon_vma structure at any moment, page_lock_anon_vma()
needs to check page_mapped() again before succeeding, otherwise
page_unlock_anon_vma() might address a different root->lock.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>