- 14 Jun, 2021 30 commits
-
-
Vladimir Oltean authored
nxp_c45_reconstruct_ts() takes a partial hardware timestamp in @hwts, with 2 bits of the 'seconds' portion, and a full PTP time in @ts. It patches in the lower bits of @hwts into @ts, and to ensure that the reconstructed timestamp is correct, it checks whether the lower 2 bits of @hwts are not in fact higher than the lower 2 bits of @ts. This is not logically possible because, according to the calling convention, @ts was collected later in time than @hwts, but due to two's complement arithmetic it can actually happen, because the current PTP time might have wrapped around between when @hwts was collected and when @ts was, yielding the lower 2 bits of @ts smaller than those of @hwts. To correct for that situation which is expected to happen under normal conditions, the driver subtracts exactly one wraparound interval from the reconstructed timestamp, since the upper bits of that need to correspond to what the upper bits of @hwts were, not to what the upper bits of @ts were. Readers might be confused because the driver denotes the amount of bits that the partial hardware timestamp has to offer as TS_SEC_MASK (timestamp mask for seconds). But it subtracts a seemingly unrelated BIT(2), which is in fact more subtle: if the hardware timestamp provides 2 bits of partial 'seconds' timestamp, then the wraparound interval is 2^2 == BIT(2). But nonetheless, it is better to express the wraparound interval in terms of a definition we already have, so replace BIT(2) with 1 + GENMASK(1, 0) which produces the same result but is clearer. Suggested-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The SJA1110 switch integrates these PHYs, and they do not have support for timestamping. This message becomes quite overwhelming: [ 10.056596] NXP C45 TJA1103 spi1.0-base-t1:01: the phy does not support PTP [ 10.112625] NXP C45 TJA1103 spi1.0-base-t1:02: the phy does not support PTP [ 10.167461] NXP C45 TJA1103 spi1.0-base-t1:03: the phy does not support PTP [ 10.223510] NXP C45 TJA1103 spi1.0-base-t1:04: the phy does not support PTP [ 10.278239] NXP C45 TJA1103 spi1.0-base-t1:05: the phy does not support PTP [ 10.332663] NXP C45 TJA1103 spi1.0-base-t1:06: the phy does not support PTP [ 15.390828] NXP C45 TJA1103 spi1.2-base-t1:01: the phy does not support PTP [ 15.445224] NXP C45 TJA1103 spi1.2-base-t1:02: the phy does not support PTP [ 15.499673] NXP C45 TJA1103 spi1.2-base-t1:03: the phy does not support PTP [ 15.554074] NXP C45 TJA1103 spi1.2-base-t1:04: the phy does not support PTP [ 15.608516] NXP C45 TJA1103 spi1.2-base-t1:05: the phy does not support PTP [ 15.662996] NXP C45 TJA1103 spi1.2-base-t1:06: the phy does not support PTP So reduce its log level to debug. Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
-
David S. Miller authored
Zhou Yanjie says: ==================== Add Ingenic SoCs MAC support. v2->v3: 1.Add "ingenic,mac.yaml" for Ingenic SoCs. 2.Change tx clk delay and rx clk delay from hardware value to ps. 3.return -EINVAL when a unsupported value is encountered when parsing the binding. 4.Simplify the code of the RGMII part of X2000 SoC according to Andrew Lunn’s suggestion. 5.Follow the example of "dwmac-mediatek.c" to improve the code that handles delays according to Andrew Lunn’s suggestion. ==================== Signed-off-by: -
周琰杰 (Zhou Yanjie) authored
Add support for Ingenic SoC MAC glue layer support for the stmmac device driver. This driver is used on for the MAC ethernet controller found in the JZ4775 SoC, the X1000 SoC, the X1600 SoC, the X1830 SoC, and the X2000 SoC. Signed-off-by:
周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Reviewed-by:
-
周琰杰 (Zhou Yanjie) authored
Add the dwmac bindings for the JZ4775 SoC, the X1000 SoC, the X1600 SoC, the X1830 SoC and the X2000 SoC from Ingenic. Signed-off-by:
-
David S. Miller authored
Oleksandr Mazur says: ==================== Marvell Prestera driver implementation of devlink functionality. This patch series implement Prestera Switchdev driver devlink traps, that are registered within the driver, as well as extend current devlink functionality by adding new hard drop statistics counter, that could be retrieved on-demand: the counter shows number of packets that have been dropped by the underlying device and haven't been passed to the devlink subsystem. The core prestera-devlink functionality is implemented in the prestera_devlink.c. The patch series also extends the existing devlink kernel API: - devlink: add trap_drop_counter_get callback for driver to register - make it possible to keep track of how many packets have been dropped (hard) by the switch device, before the packets even made it to the devlink subsystem (e.g. dropped due to RXDMA buffer overflow). The core features that extend current functionality of prestera Switchdev driver: - add logic for driver traps and drops registration (also traps with DROP action). - add documentation for prestera driver traps and drops group. PATCH v2: 1) Rebase whole series on top of latest mater; 2) Remove storm control-related patches, as they're out of devlink scope; ==================== Signed-off-by: -
Oleksandr Mazur authored
Add documentation for the devlink feature prestera switchdev driver supports: add description for the support of the driver-specific devlink traps (include both traps with action TRAP and action DROP); Signed-off-by:
Oleksandr Mazur <oleksandr.mazur@plvision.eu> Signed-off-by:
-
Oleksandr Mazur authored
Add traps that have init_action being set to DROP. Add 'trap_drop_counter_get' (devlink API) callback implementation, that is used to get number of packets that have been dropped by the HW (traps with action 'DROP'). Add new FW command CPU_CODE_COUNTERS_GET. Signed-off-by:
-
Oleksandr Mazur authored
Add devlink traps registration (with corresponding groups) for all the traffic types that driver traps to the CPU; prestera_rxtx: report each packet trapped to the CPU (RX) to the prestera_devlink; Signed-off-by:
-
Oleksandr Mazur authored
Add hard drop counter check testcase, to make sure netdevsim driver properly handles the devlink hard drop counters get/set callbacks. Signed-off-by:
-
Oleksandr Mazur authored
Whenever query statistics is issued for trap with DROP action, devlink subsystem would also fill-in statistics 'dropped' field. In case if device driver did't register callback for hard drop statistics querying, 'dropped' field will be omitted and not filled. Add trap_drop_counter_get callback implementation to the netdevsim. Add new test cases for netdevsim, to test both the callback functionality, as well as drop statistics alteration check. Signed-off-by:
-
Oleksandr Mazur authored
testing: selftests: net: forwarding: add devlink-required functionality to test (hard) dropped stats field Add devlink_trap_drop_packets_get function, as well as test that are used to verify devlink (hard) dropped stats functionality works. Signed-off-by:
-
Oleksandr Mazur authored
Whenever query statistics is issued for trap, devlink subsystem would also fill-in statistics 'dropped' field. This field indicates the number of packets HW dropped and failed to report to the device driver, and thus - to the devlink subsystem itself. In case if device driver didn't register callback for hard drop statistics querying, 'dropped' field will be omitted and not filled. Signed-off-by:
-
Loic Poulain authored
Author forgot to remove that flag. Fixes: f7af616c ("net: iosm: infrastructure") Reported-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Signed-off-by:
-
Lijun Pan authored
The 3rd argument is u32 by function definition while it is __be32 by function declaration. Signed-off-by:
Lijun Pan <lijunp213@gmail.com> Signed-off-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== provide cable test support for the ksz886x switch changes v5: - drop resume() patch - add Reviewed-by tags. - rework dsa_slave_phy_connect() patch changes v4: - use fallthrough; - use EOPNOTSUPP instead of ENOTSUPP - drop flags variable in dsa_slave_phy_connect patch - extend description for the "net: phy: micrel: apply resume errat" patch - fix "use consistent alignments" patch changes v3: - remove RFC tag changes v2: - use generic MII_* defines where possible - rework phylink validate - remove phylink get state function - reorder cabletest patches to make PHY flag patch in the right order - fix MDI-X detection This patches provide support for cable testing on the ksz886x switches. Since it has one special port, we needed to add phylink with validation and extra quirk for the PHY to signal, that one port will not provide valid cable testing reports. ==================== Signed-off-by: -
Oleksij Rempel authored
This patch support for cable test for the ksz886x switches and the ksz8081 PHY. The patch was tested on a KSZ8873RLL switch with following results: - port 1: - provides invalid values, thus return -ENOTSUPP (Errata: DS80000830A: "LinkMD does not work on Port 1", http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf) - port 2: - can detect distance - can detect open on each wire of pair A (wire 1 and 2) - can detect open only on one wire of pair B (only wire 3) - can detect short between wires of a pair (wires 1 + 2 or 3 + 6) - short between pairs is detected as open. For example short between wires 2 + 3 is detected as open. Signed-off-by:Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Oleksij Rempel authored
The current get_phy_flags() is only processed when we connect to a PHY via a designed phy-handle property via phylink_of_phy_connect(), but if we fallback on the internal MDIO bus created by a switch and take the dsa_slave_phy_connect() path then we would not be processing that flag and using it at PHY connection time. Suggested-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Oleksij Rempel authored
Add mapping for LINK_MD register to enable cable testing functionality. Signed-off-by:
-
Oleksij Rempel authored
Add support for MDI-X status and configuration Signed-off-by:
-
Oleksij Rempel authored
Add support for MDI-X status and configuration Signed-off-by:
-
Oleksij Rempel authored
This patch changes the alignments to one space between "#define" and the macro. Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
-
Michael Grzeschik authored
This patch adds the phylink support to the ksz8795 driver to provide configuration exceptions on quirky KSZ8863 and KSZ8873 ports. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
-
Michael Grzeschik authored
Some micrel devices share the same PHY register defines. This patch moves them to one common header so other drivers can reuse them. And reuse generic MII_* defines where possible. Signed-off-by:
-
Taehee Yoo authored
If link mtu is too big, mld_newpack() allocates high-order page. But most mld packets don't need high-order page. So, it might waste unnecessary pages. To avoid this, it makes mld_newpack() try to allocate order-0 page. Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Alex Elder authored
A recent change tidied up some conditional code, avoiding the use of some #ifdefs. Unfortunately, if CONFIG_IPV6 was not enabled, it meant that two functions were referenced but never defined. The easiest fix is to just define stubs for these functions if CONFIG_IPV6 is not defined. This will soon be simplified further by some other development in the works... Reported-by:
kernel test robot <lkp@intel.com> Fixes: 75db5b07 ("net: qualcomm: rmnet: eliminate some ifdefs") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
-
Colin Ian King authored
The variable err is being initialized with a value that is never read, the assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Colin Ian King authored
The pointer of_node is being initialized with a value that is never read and it is being updated later with a new value inside a do-while loop. The initialization is redundant and can be removed and the pointer dev is no longer required and can be removed too. Addresses-Coverity: ("Unused value") Signed-off-by: -
Sunil Goutham authored
Current MCAM allocation scheme allocates a single lot of MCAM entries for ntuple filters, unicast filters and VF VLAN rules. This patch attempts to cleanup this logic by segregating MCAM rule allocation and management for Ntuple rules and unicast, VF VLAN rules. This segregation will result in reusing most of the logic for supporting ntuple filters for VF devices. Also added debug messages for MCAM entry allocation failures. Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
-
David Ahern authored
Test cleanup path for routes usinig nexthop objects before the reference is taken on the nexthop. Specifically, bad metric for ipv4 and ipv6 and source routing for ipv6. Selftests that correspond to the recent bug fix: 821bbf79 ("ipv6: Fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions") Signed-off-by:David Ahern <dsahern@kernel.org> Cc: Coco Li <lixiaoyan@google.com> Signed-off-by:
-
- 13 Jun, 2021 10 commits
-
-
David S. Miller authored
M Chetan Kumar says: ==================== net: iosm: PCIe Driver for Intel M.2 Modem The IOSM (IPC over Shared Memory) driver is a PCIe host driver implemented for linux or chrome platform for data exchange over PCIe interface between Host platform & Intel M.2 Modem. The driver exposes interface conforming to the MBIM protocol. Any front end application ( eg: Modem Manager) could easily manage the MBIM interface to enable data communication towards WWAN. Intel M.2 modem uses 2 BAR regions. The first region is dedicated to Doorbell register for IRQs and the second region is used as scratchpad area for book keeping modem execution stage details along with host system shared memory region context details. The upper edge of the driver exposes the control and data channels for user space application interaction. At lower edge these data and control channels are associated to pipes. The pipes are lowest level interfaces used over PCIe as a logical channel for message exchange. A single channel maps to UL and DL pipe and are initialized on device open. On UL path, driver copies application sent data to SKBs associate it with transfer descriptor and puts it on to ring buffer for DMA transfer. Once information has been updated in shared memory region, host gives a Doorbell to modem to perform DMA and modem uses MSI to communicate back to host. For receiving data in DL path, SKBs are pre-allocated during pipe open and transfer descriptors are given to modem for DMA transfer. The driver exposes two types of ports, namely "wwan0mbim0", a char device node which is used for MBIM control operation and "wwan0-x",(x = 0,1,2..7) network interfaces for IP data communication. 1) MBIM Control Interface: This node exposes an interface between modem and application using char device exposed by "IOSM" driver to establish and manage the MBIM data communication with PCIe based Intel M.2 Modems. 2) MBIM Data Interface: The IOSM driver exposes IP link interface "wwan0-x" of type "wwan" for IP traffic. Iproute network utility is used for creating "wwan0-x" network interface and for associating it with MBIM IP session. The Driver supports upto 8 IP sessions for simultaneous IP communication. This applies on top of WWAN core rtnetlink series posted here: https://lore.kernel.org/netdev/1623486057-13075-1-git-send-email-loic.poulain@linaro.org/ Also driver has been compiled and tested on top of netdev net-next tree. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/ ==================== Signed-off-by:
-
M Chetan Kumar authored
1) Kconfig & Makefile changes for IOSM Driver compilation. 2) Add IOSM Driver documentation. 3) Modified MAINTAINER file for IOSM Driver addition. Signed-off-by:
M Chetan Kumar <m.chetan.kumar@intel.com> Signed-off-by:
-
M Chetan Kumar authored
1) Create net device & implement net operations for data/IP communication. 2) Bind IP Link to mux IP session for simultaneous IP traffic. Signed-off-by:
-
M Chetan Kumar authored
Report modem status via uevent. Signed-off-by:
-
M Chetan Kumar authored
1) Update UL/DL transfer descriptors in message ring. 2) Define message set for pipe/sleep protocol. Signed-off-by:
-
M Chetan Kumar authored
1) Defines messaging protocol for handling Transfer Descriptor in both UL/DL direction. 2) Ring buffer management. Signed-off-by:
-
M Chetan Kumar authored
Implements state machine to handle host & device sleep. Signed-off-by:
-
M Chetan Kumar authored
1) Encode UL packet into datagram. 2) Decode DL datagram and route it to network layer. 3) Supports credit based flow control. Signed-off-by:
-
M Chetan Kumar authored
Establish IP session between host-device & session management. Signed-off-by:
-
M Chetan Kumar authored
1) Bottom half(tasklet) for IRQ and task processing. 2) Tasks are processed asynchronous and synchronously. Signed-off-by:
-
