- 05 Jul, 2017 40 commits
-
-
Eric Farman authored
[ Upstream commit 773c7220 ] In the case of a graceful set of detaches, where the virtio-scsi-ccw disk is removed from the guest prior to the controller, the guest behaves quite normally. Specifically, the detach gets us into sd_sync_cache to issue a Synchronize Cache(10) command, which immediately fails (and is retried a couple of times) because the device has been removed. Later, the removal of the controller sees two CRWs presented, but there's no further indication of the removal from the guest viewpoint. [ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK [ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2 [ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0 However, on s390, the SCSI disks can be removed "by surprise" when an entire controller (host) is removed and all associated disks are removed via the loop in scsi_forget_host. The same call to sd_sync_cache is made, but because the controller has already been removed, the Synchronize Cache(10) command is neither issued (and then failed) nor rejected. That the I/O isn't returned means the guest cannot have other devices added nor removed, and other tasks (such as shutdown or reboot) issued by the guest will not complete either. The virtio ring has already been marked as broken (via virtio_break_device in virtio_ccw_remove), but we still attempt to queue the command only to have it remain there. The calling sequence provides a bit of distinction for us: virtscsi_queuecommand() -> virtscsi_kick_cmd() -> virtscsi_add_cmd() -> virtqueue_add_sgs() -> virtqueue_add() if success return 0 elseif vq->broken or vring_mapping_error() return -EIO else return -ENOSPC A return of ENOSPC is generally a temporary condition, so returning "host busy" from virtscsi_queuecommand makes sense here, to have it redriven in a moment or two. But the EIO return code is more of a permanent error and so it would be wise to return the I/O itself and allow the calling thread to finish gracefully. The result is these four kernel messages in the guest (the fourth one does not occur prior to this patch): [ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2 [ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0 [ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK I opted to fill in the same response data that is returned from the more graceful device detach, where the disk device is removed prior to the controller device. Signed-off-by:
Eric Farman <farman@linux.vnet.ibm.com> Reviewed-by:
Fam Zheng <famz@redhat.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Vineeth Remanan Pillai authored
[ Upstream commit 90c311b0 ] During an OOM scenario, request slots could not be created as skb allocation fails. So the netback cannot pass in packets and netfront wrongly assumes that there is no more work to be done and it disables polling. This causes Rx to stall. The issue is with the retry logic which schedules the timer if the created slots are less than NET_RX_SLOTS_MIN. The count of new request slots to be pushed are calculated as a difference between new req_prod and rsp_cons which could be more than the actual slots, if there are unconsumed responses. The fix is to calculate the count of newly created slots as the difference between new req_prod and old req_prod. Signed-off-by:
Vineeth Remanan Pillai <vineethp@amazon.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Stefano Stabellini authored
[ Upstream commit f1225ee4 ] In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original page is not suitable, we swap it for another page from the swiotlb pool. In these cases, we don't update the previously calculated dma address for the page before calling xen_dma_map_page. Thus, we end up calling xen_dma_map_page passing the wrong dev_addr, resulting in xen_dma_map_page mistakenly assuming that the page is foreign when it is local. Fix the bug by updating dev_addr appropriately. This change has no effect on x86, because xen_dma_map_page is a stub there. Signed-off-by:
Stefano Stabellini <sstabellini@kernel.org> Signed-off-by:
Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com> Tested-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
G. Campana authored
[ Upstream commit 8379cadf ] Using control_work instead of config_work as the 3rd argument to container_of results in an invalid portdev pointer. Indeed, the work structure is initialized as below: INIT_WORK(&portdev->config_work, &config_work_handler); It leads to a crash when portdev->vdev is dereferenced later. This bug is triggered when the guest uses a virtio-console without multiport feature and receives a config_changed virtio interrupt. Signed-off-by:
G. Campana <gcampana@quarkslab.com> Reviewed-by:
Amit Shah <amit.shah@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Liu Bo authored
[ Upstream commit 91298eec ] For such a file mapping, [0-4k][hole][8k-12k] In NO_HOLES mode, we don't have the [hole] extent any more. Commit c1aa4575 ("Btrfs: fix shrinking truncate when the no_holes feature is enabled") fixed disk isize not being updated in NO_HOLES mode when data is not flushed. However, even if data has been flushed, we can still have trouble in updating disk isize since we updated disk isize to 'start' of the last evicted extent. Reviewed-by:
Chris Mason <clm@fb.com> Signed-off-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 69fed99b ] A driver using dev_alloc_page() must not reuse a page that had to use emergency memory reserve. Otherwise all packets using this page will be immediately dropped, unless for very specific sockets having SOCK_MEMALLOC bit set. This issue might be hard to debug, because only a fraction of the RX ring buffer would suffer from drops. Fixes: 75354148 ("gianfar: Add paged allocation and Rx S/G") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Claudiu Manoil <claudiu.manoil@freescale.com> Acked-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
Gavin Shan authored
[ Upstream commit 387bbc97 ] We give up recovery on permanent error, simply shutdown the affected devices and remove them. If the devices can't be put into quiet state, they spew more traffic that is likely to cause another unexpected EEH error. This was observed on "p8dtu2u" machine: 0002:00:00.0 PCI bridge: IBM Device 03dc 0002:01:00.0 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.1 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.2 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) 0002:01:00.3 Ethernet controller: Intel Corporation \ Ethernet Controller X710/X557-AT 10GBASE-T (rev 02) On P8 PowerNV platform, the IO path is frozen when shutdowning the devices, meaning the memory registers are inaccessible. It is why the devices can't be put into quiet state before removing them. This fixes the issue by enabling IO path prior to putting the devices into quiet state. Reported-by:
Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com> Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Acked-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Florian Fainelli authored
commit 3894396e upstream. bgmac_open() calls phy_start() to initialize the PHY state machine, which will set the interface's carrier state accordingly, no need to force that as this could be conflicting with the PHY state determined by PHYLIB. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
Florian Fainelli authored
commit c3897f2a upstream. The driver does not start the transmit queue in bgmac_open(). If the queue was stopped prior to closing then re-opening the interface, we would never be able to wake-up again. Fixes: dd4544f0 ("bgmac: driver for GBit MAC core on BCMA bus") Signed-off-by:
-
Florian Fainelli authored
commit d2b13233 upstream. We are checking for the Start of Frame bit in the ctl1 word, while this bit is set in the ctl0 word instead. Read the ctl0 word and update the check to verify that. Fixes: 9cde9450 ("bgmac: implement scatter/gather support") Signed-off-by:
-
David S. Miller authored
commit 750afbf8 upstream. Fixes: f1640c3d ("bgmac: fix a missing check for build_skb") Signed-off-by:
-
Rafał Miłecki authored
commit 36bcc0c9 upstream. Bit-flip errors may occur on NAND flashes and are harmless. Handle them gracefully as read content is still reliable and can be parsed. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
wangweidong authored
commit f1640c3d upstream. when build_skb failed, it may occure a NULL pointer. So add a 'NULL check' for it. Signed-off-by:
Weidong Wang <wangweidong1@huawei.com> Signed-off-by:
-
Rafał Miłecki authored
commit 2a36a5c3 upstream. We allowed using bcm47xxpart on BCM5301X arch with commit: 9e3afa5f ("mtd: bcm47xxpart: allow enabling on ARCH_BCM_5301X") BCM5301X devices may contain some partitions in higher memory, e.g. Netgear R8000 has board_data at 0x2600000. To detect them we should use size limit on MIPS only. Signed-off-by:
-
Álvaro Fernández Rojas authored
commit 07b50db6 upstream. Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> Cc: john@phrozen.org Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13307/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Álvaro Fernández Rojas authored
commit d7146829 upstream. Signed-off-by:
-
John Crispin authored
commit 0af3a40f upstream. Commit 418d29c8 ("MIPS: ralink: Unify SoC id handling") introduced broken code. We obviously need to assign the value. Signed-off-by:
John Crispin <blogic@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11993/Signed-off-by:
-
John Crispin authored
commit fad25222 upstream. Commit 418d29c8 ("MIPS: ralink: Unify SoC id handling") was not fully correct. The logic for the SoC check got inverted. We need to check if it is not a MT76x8. Signed-off-by:
-
John Crispin authored
commit e906a5f6 upstream. A few fixes to the pinmux data, 2 new muxes and a minor whitespace cleanup. Signed-off-by:
-
Florian Fainelli authored
commit e6afb1ad upstream. Commit beb0babf ("korina: disable napi on close and restart") introduced calls to napi_disable() that were missing before, unfortunately this leaves a small window during which NAPI has a chance to run, yet we just freed resources since korina_free_ring() has been called: Fix this by disabling NAPI first then freeing resource, and make sure that we also cancel the restart task before doing the resource freeing. Fixes: beb0babf ("korina: disable napi on close and restart") Reported-by:
Alexandros C. Couloumbis <alex@ozo.com> Signed-off-by:
-
Felix Fietkau authored
commit 9184dc8f upstream. ath79_ddr_pci_win_base has the type void __iomem *, so register offsets need to be a multiple of 4. Cc: Alban Bedel <albeu@free.fr> Fixes: 24b0e3e8 ("MIPS: ath79: Improve the DDR controller interface") Signed-off-by:
Felix Fietkau <nbd@nbd.name> Cc: sergei.shtylyov@cogentembedded.com Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13258/Signed-off-by:
-
Gregory CLEMENT authored
commit 129219e4 upstream. This patch convert the for_each_present in on_each_cpu, instead of applying on the present cpus it will be applied only on the online cpus. This fix a bug reported on http://thread.gmane.org/gmane.linux.ports.arm.kernel/468173. Using the macro on_each_cpu (instead of a for_each_* loop) also ensures that all the calls will be done all at once. Fixes: f8642885 ("net: mvneta: Statically assign queues to CPUs") Reported-by:
Stefan Roese <stefan.roese@gmail.com> Suggested-by:
Jisheng Zhang <jszhang@marvell.com> Suggested-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Jon Mason authored
commit 0c2bf9f9 upstream. GIC_PPI flags were misconfigured for the timers, resulting in errors like: [ 0.000000] GIC: PPI11 is secure or misconfigured Changing them to being edge triggered corrects the issue Suggested-by:
Rafał Miłecki <rafal@milecki.pl> Signed-off-by:
Jon Mason <jon.mason@broadcom.com> Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC") Signed-off-by:
-
Quinn Tran authored
[ Upstream commit 4f060736 ] Termination of Immediate Notify IOCB was using wrong IOCB handle. IOCB completion code was unable to find appropriate code path due to wrong handle. Following message is seen in the logs. "Error entry - invalid handle/queue (ffff)." Signed-off-by:
Quinn Tran <quinn.tran@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> [ bvanassche: Fixed word order in patch title ] Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by:
-
Johannes Thumshirn authored
[ Upstream commit 8667f515 ] Set the elsiocb contexts to NULL after freeing as others depend on it. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Acked-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
-
Damien Le Moal authored
[ Upstream commit 26f28197 ] Zoned block devices force the use of READ/WRITE(16) commands by setting sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in DPOFUA always being disabled for these drives as the assumed use of the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw. Strenghten the test by also checking that sdkp->use_16_for_rw is false. Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Dmitry Vyukov authored
[ Upstream commit ce2e852e ] emulator_fix_hypercall() replaces hypercall with vmcall instruction, but it does not handle GP exception properly when writes the new instruction. It can return X86EMUL_PROPAGATE_FAULT without setting exception information. This leads to incorrect emulation and triggers WARN_ON(ctxt->exception.vector > 0x1f) in x86_emulate_insn() as discovered by syzkaller fuzzer: WARNING: CPU: 2 PID: 18646 at arch/x86/kvm/emulate.c:5558 Call Trace: warn_slowpath_null+0x2c/0x40 kernel/panic.c:582 x86_emulate_insn+0x16a5/0x4090 arch/x86/kvm/emulate.c:5572 x86_emulate_instruction+0x403/0x1cc0 arch/x86/kvm/x86.c:5618 emulate_instruction arch/x86/include/asm/kvm_host.h:1127 [inline] handle_exception+0x594/0xfd0 arch/x86/kvm/vmx.c:5762 vmx_handle_exit+0x2b7/0x38b0 arch/x86/kvm/vmx.c:8625 vcpu_enter_guest arch/x86/kvm/x86.c:6888 [inline] vcpu_run arch/x86/kvm/x86.c:6947 [inline] Set exception information when write in emulator_fix_hypercall() fails. Signed-off-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Wanpeng Li <wanpeng.li@hotmail.com> Cc: kvm@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Mark Rutland authored
commit 3c226c63 upstream. In do_huge_pmd_numa_page(), we attempt to handle a migrating thp pmd by waiting until the pmd is unlocked before we return and retry. However, we can race with migrate_misplaced_transhuge_page(): // do_huge_pmd_numa_page // migrate_misplaced_transhuge_page() // Holds 0 refs on page // Holds 2 refs on page vmf->ptl = pmd_lock(vma->vm_mm, vmf->pmd); /* ... */ if (pmd_trans_migrating(*vmf->pmd)) { page = pmd_page(*vmf->pmd); spin_unlock(vmf->ptl); ptl = pmd_lock(mm, pmd); if (page_count(page) != 2)) { /* roll back */ } /* ... */ mlock_migrate_page(new_page, page); /* ... */ spin_unlock(ptl); put_page(page); put_page(page); // page freed here wait_on_page_locked(page); goto out; } This can result in the freed page having its waiters flag set unexpectedly, which trips the PAGE_FLAGS_CHECK_AT_PREP checks in the page alloc/free functions. This has been observed on arm64 KVM guests. We can avoid this by having do_huge_pmd_numa_page() take a reference on the page before dropping the pmd lock, mirroring what we do in __migration_entry_wait(). When we hit the race, migrate_misplaced_transhuge_page() will see the reference and abort the migration, as it may do today in other cases. Fixes: b8916634 ("mm: Prevent parallel splits during THP migration") Link: http://lkml.kernel.org/r/1497349722-6731-2-git-send-email-will.deacon@arm.comSigned-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Acked-by:
Steve Capper <steve.capper@arm.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Roman Pen authored
commit 39a169b6 upstream. get_disk(),get_gendisk() calls have non explicit side effect: they increase the reference on the disk owner module. The following is the correct sequence how to get a disk reference and to put it: disk = get_gendisk(...); /* use disk */ owner = disk->fops->owner; put_disk(disk); module_put(owner); fs/block_dev.c is aware of this required module_put() call, but f.e. blkg_conf_finish(), which is located in block/blk-cgroup.c, does not put a module reference. To see a leakage in action cgroups throttle config can be used. In the following script I'm removing throttle for /dev/ram0 (actually this is NOP, because throttle was never set for this device): # lsmod | grep brd brd 5175 0 # i=100; while [ $i -gt 0 ]; do echo "1:0 0" > \ /sys/fs/cgroup/blkio/blkio.throttle.read_bps_device; i=$(($i - 1)); \ done # lsmod | grep brd brd 5175 100 Now brd module has 100 references. The issue is fixed by calling module_put() just right away put_disk(). Signed-off-by:
Roman Pen <roman.penyaev@profitbricks.com> Cc: Gi-Oh Kim <gi-oh.kim@profitbricks.com> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: linux-block@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@fb.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by:
-
Kees Cook authored
commit 41662f5c upstream. SYSCTL_WRITES_WARN was added in commit f4aacea2 ("sysctl: allow for strict write position handling"), and released in v3.16 in August of 2014. Since then I can find only 1 instance of non-zero offset writing[1], and it was fixed immediately in CRIU[2]. As such, it appears safe to flip this to the strict state now. [1] https://www.google.com/search?q="when%20file%20position%20was%20not%200" [2] http://lists.openvz.org/pipermail/criu/2015-April/019819.htmlSigned-off-by:
Kees Cook <keescook@chromium.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Baolin Wang authored
commit b3ce3ce0 upstream. When system try to close /dev/usb-ffs/adb/ep0 on one core, at the same time another core try to attach new UDC, which will cause deadlock as below scenario. Thus we should release ffs lock before issuing unregister_gadget_item(). [ 52.642225] c1 ====================================================== [ 52.642228] c1 [ INFO: possible circular locking dependency detected ] [ 52.642236] c1 4.4.6+ #1 Tainted: G W O [ 52.642241] c1 ------------------------------------------------------- [ 52.642245] c1 usb ffs open/2808 is trying to acquire lock: [ 52.642270] c0 (udc_lock){+.+.+.}, at: [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8 [ 52.642272] c1 but task is already holding lock: [ 52.642283] c0 (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>] ffs_data_clear+0x30/0x140 [ 52.642285] c1 which lock already depends on the new lock. [ 52.642287] c1 the existing dependency chain (in reverse order) is: [ 52.642295] c0 -> #1 (ffs_lock){+.+.+.}: [ 52.642307] c0 [<ffffffc00012340c>] __lock_acquire+0x20f0/0x2238 [ 52.642314] c0 [<ffffffc000123b54>] lock_acquire+0xe4/0x298 [ 52.642322] c0 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc [ 52.642328] c0 [<ffffffc00066f7bc>] ffs_func_bind+0x504/0x6e8 [ 52.642334] c0 [<ffffffc000654004>] usb_add_function+0x84/0x184 [ 52.642340] c0 [<ffffffc000658ca4>] configfs_composite_bind+0x264/0x39c [ 52.642346] c0 [<ffffffc00065b348>] udc_bind_to_driver+0x58/0x11c [ 52.642352] c0 [<ffffffc00065b49c>] usb_udc_attach_driver+0x90/0xc8 [ 52.642358] c0 [<ffffffc0006598e0>] gadget_dev_desc_UDC_store+0xd4/0x128 [ 52.642369] c0 [<ffffffc0002c14e8>] configfs_write_file+0xd0/0x13c [ 52.642376] c0 [<ffffffc00023c054>] vfs_write+0xb8/0x214 [ 52.642381] c0 [<ffffffc00023cad4>] SyS_write+0x54/0xb0 [ 52.642388] c0 [<ffffffc000085ff0>] el0_svc_naked+0x24/0x28 [ 52.642395] c0 -> #0 (udc_lock){+.+.+.}: [ 52.642401] c0 [<ffffffc00011e3d0>] print_circular_bug+0x84/0x2e4 [ 52.642407] c0 [<ffffffc000123454>] __lock_acquire+0x2138/0x2238 [ 52.642412] c0 [<ffffffc000123b54>] lock_acquire+0xe4/0x298 [ 52.642420] c0 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc [ 52.642427] c0 [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8 [ 52.642432] c0 [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44 [ 52.642439] c0 [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140 [ 52.642444] c0 [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c [ 52.642450] c0 [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c [ 52.642454] c0 [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c [ 52.642460] c0 [<ffffffc00023dbe4>] __fput+0xb0/0x1f4 [ 52.642466] c0 [<ffffffc00023dd9c>] ____fput+0x20/0x2c [ 52.642473] c0 [<ffffffc0000ee944>] task_work_run+0xb4/0xe8 [ 52.642482] c0 [<ffffffc0000cd45c>] do_exit+0x360/0xb9c [ 52.642487] c0 [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0 [ 52.642494] c0 [<ffffffc0000dd3c8>] get_signal+0x380/0x89c [ 52.642501] c0 [<ffffffc00008a8f0>] do_signal+0x154/0x518 [ 52.642507] c0 [<ffffffc00008af00>] do_notify_resume+0x70/0x78 [ 52.642512] c0 [<ffffffc000085ee8>] work_pending+0x1c/0x20 [ 52.642514] c1 other info that might help us debug this: [ 52.642517] c1 Possible unsafe locking scenario: [ 52.642518] c1 CPU0 CPU1 [ 52.642520] c1 ---- ---- [ 52.642525] c0 lock(ffs_lock); [ 52.642529] c0 lock(udc_lock); [ 52.642533] c0 lock(ffs_lock); [ 52.642537] c0 lock(udc_lock); [ 52.642539] c1 *** DEADLOCK *** [ 52.642543] c1 1 lock held by usb ffs open/2808: [ 52.642555] c0 #0: (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>] ffs_data_clear+0x30/0x140 [ 52.642557] c1 stack backtrace: [ 52.642563] c1 CPU: 1 PID: 2808 Comm: usb ffs open Tainted: G [ 52.642565] c1 Hardware name: Spreadtrum SP9860g Board (DT) [ 52.642568] c1 Call trace: [ 52.642573] c1 [<ffffffc00008b430>] dump_backtrace+0x0/0x170 [ 52.642577] c1 [<ffffffc00008b5c0>] show_stack+0x20/0x28 [ 52.642583] c1 [<ffffffc000422694>] dump_stack+0xa8/0xe0 [ 52.642587] c1 [<ffffffc00011e548>] print_circular_bug+0x1fc/0x2e4 [ 52.642591] c1 [<ffffffc000123454>] __lock_acquire+0x2138/0x2238 [ 52.642595] c1 [<ffffffc000123b54>] lock_acquire+0xe4/0x298 [ 52.642599] c1 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc [ 52.642604] c1 [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8 [ 52.642608] c1 [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44 [ 52.642613] c1 [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140 [ 52.642618] c1 [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c [ 52.642621] c1 [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c [ 52.642625] c1 [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c [ 52.642629] c1 [<ffffffc00023dbe4>] __fput+0xb0/0x1f4 [ 52.642633] c1 [<ffffffc00023dd9c>] ____fput+0x20/0x2c [ 52.642636] c1 [<ffffffc0000ee944>] task_work_run+0xb4/0xe8 [ 52.642640] c1 [<ffffffc0000cd45c>] do_exit+0x360/0xb9c [ 52.642644] c1 [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0 [ 52.642647] c1 [<ffffffc0000dd3c8>] get_signal+0x380/0x89c [ 52.642651] c1 [<ffffffc00008a8f0>] do_signal+0x154/0x518 [ 52.642656] c1 [<ffffffc00008af00>] do_notify_resume+0x70/0x78 [ 52.642659] c1 [<ffffffc000085ee8>] work_pending+0x1c/0x20 Acked-by:
Michal Nazarewicz <mina86@mina86.com> Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Jerry Zhang <zhangjerry@google.com> Signed-off-by:
-
Deepak Rawat authored
commit 82fcee52 upstream. The hash table created during vmw_cmdbuf_res_man_create was never freed. This causes memory leak in context creation. Added the corresponding drm_ht_remove in vmw_cmdbuf_res_man_destroy. Tested for memory leak by running piglit overnight and kernel memory is not inflated which earlier was. Signed-off-by:
Deepak Rawat <drawat@vmware.com> Reviewed-by:
Sinclair Yeh <syeh@vmware.com> Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by:
-
Hui Wang authored
commit a8f20fd2 upstream. Recently we met a problem, the codec has valid adcs and input pins, and they can form valid input paths, but the driver does not build valid controls for them like "Mic boost", "Capture Volume" and "Capture Switch". Through debugging, I found the driver needs to shrink the invalid adcs and input paths for this machine, so it will move the whole column bitmap value to the previous column, after moving it, the driver forgets to set the original column bitmap value to zero, as a result, the driver will invalidate the path whose index value is the original colume bitmap value. After executing this function, all valid input paths are invalidated by a mistake, there are no any valid input paths, so the driver won't build controls for them. Fixes: 3a65bcdc ("ALSA: hda - Fix inconsistent input_paths after ADC reduction") Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit d94815f9 upstream. azx_codec_configure() loops over the codecs found on the given controller via a linked list. The code used to work in the past, but in the current version, this may lead to an endless loop when a codec binding returns an error. The culprit is that the snd_hda_codec_configure() unregisters the device upon error, and this eventually deletes the given codec object from the bus. Since the list is initialized via list_del_init(), the next object points to the same device itself. This behavior change was introduced at splitting the HD-audio code code, and forgotten to adapt it here. For fixing this bug, just use a *_safe() version of list iteration. Fixes: d068ebc2 ("ALSA: hda - Move some codes up to hdac_bus struct") Reported-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Paul Burton authored
commit d8550860 upstream. When the scheduler sets TIF_NEED_RESCHED & we call into the scheduler from arch/mips/kernel/entry.S we disable interrupts. This is true regardless of whether we reach work_resched from syscall_exit_work, resume_userspace or by looping after calling schedule(). Although we disable interrupts in these paths we don't call trace_hardirqs_off() before calling into C code which may acquire locks, and we therefore leave lockdep with an inconsistent view of whether interrupts are disabled or not when CONFIG_PROVE_LOCKING & CONFIG_DEBUG_LOCKDEP are both enabled. Without tracing this interrupt state lockdep will print warnings such as the following once a task returns from a syscall via syscall_exit_partial with TIF_NEED_RESCHED set: [ 49.927678] ------------[ cut here ]------------ [ 49.934445] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3687 check_flags.part.41+0x1dc/0x1e8 [ 49.946031] DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled) [ 49.946355] CPU: 0 PID: 1 Comm: init Not tainted 4.10.0-00439-gc9fd5d362289-dirty #197 [ 49.963505] Stack : 0000000000000000 ffffffff81bb5d6a 0000000000000006 ffffffff801ce9c4 [ 49.974431] 0000000000000000 0000000000000000 0000000000000000 000000000000004a [ 49.985300] ffffffff80b7e487 ffffffff80a24498 a8000000ff160000 ffffffff80ede8b8 [ 49.996194] 0000000000000001 0000000000000000 0000000000000000 0000000077c8030c [ 50.007063] 000000007fd8a510 ffffffff801cd45c 0000000000000000 a8000000ff127c88 [ 50.017945] 0000000000000000 ffffffff801cf928 0000000000000001 ffffffff80a24498 [ 50.028827] 0000000000000000 0000000000000001 0000000000000000 0000000000000000 [ 50.039688] 0000000000000000 a8000000ff127bd0 0000000000000000 ffffffff805509bc [ 50.050575] 00000000140084e0 0000000000000000 0000000000000000 0000000000040a00 [ 50.061448] 0000000000000000 ffffffff8010e1b0 0000000000000000 ffffffff805509bc [ 50.072327] ... [ 50.076087] Call Trace: [ 50.079869] [<ffffffff8010e1b0>] show_stack+0x80/0xa8 [ 50.086577] [<ffffffff805509bc>] dump_stack+0x10c/0x190 [ 50.093498] [<ffffffff8015dde0>] __warn+0xf0/0x108 [ 50.099889] [<ffffffff8015de34>] warn_slowpath_fmt+0x3c/0x48 [ 50.107241] [<ffffffff801c15b4>] check_flags.part.41+0x1dc/0x1e8 [ 50.114961] [<ffffffff801c239c>] lock_is_held_type+0x8c/0xb0 [ 50.122291] [<ffffffff809461b8>] __schedule+0x8c0/0x10f8 [ 50.129221] [<ffffffff80946a60>] schedule+0x30/0x98 [ 50.135659] [<ffffffff80106278>] work_resched+0x8/0x34 [ 50.142397] ---[ end trace 0cb4f6ef5b99fe21 ]--- [ 50.148405] possible reason: unannotated irqs-off. [ 50.154600] irq event stamp: 400463 [ 50.159566] hardirqs last enabled at (400463): [<ffffffff8094edc8>] _raw_spin_unlock_irqrestore+0x40/0xa8 [ 50.171981] hardirqs last disabled at (400462): [<ffffffff8094eb98>] _raw_spin_lock_irqsave+0x30/0xb0 [ 50.183897] softirqs last enabled at (400450): [<ffffffff8016580c>] __do_softirq+0x4ac/0x6a8 [ 50.195015] softirqs last disabled at (400425): [<ffffffff80165e78>] irq_exit+0x110/0x128 Fix this by using the TRACE_IRQS_OFF macro to call trace_hardirqs_off() when CONFIG_TRACE_IRQFLAGS is enabled. This is done before invoking schedule() following the work_resched label because: 1) Interrupts are disabled regardless of the path we take to reach work_resched() & schedule(). 2) Performing the tracing here avoids the need to do it in paths which disable interrupts but don't call out to C code before hitting a path which uses the RESTORE_SOME macro that will call trace_hardirqs_on() or trace_hardirqs_off() as appropriate. We call trace_hardirqs_on() using the TRACE_IRQS_ON macro before calling syscall_trace_leave() for similar reasons, ensuring that lockdep has a consistent view of state after we re-enable interrupts. Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Fixes: 1da177e4 ("Linux-2.6.12-rc2") Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/15385/Signed-off-by:
-
Paul Burton authored
commit 161c51cc upstream. We allocate memory for a ready_count variable per-CPU, which is accessed via a cached non-coherent TLB mapping to perform synchronisation between threads within the core using LL/SC instructions. In order to ensure that the variable is contained within its own data cache line we allocate 2 lines worth of memory & align the resulting pointer to a line boundary. This is however unnecessary, since kmalloc is guaranteed to return memory which is at least cache-line aligned (see ARCH_DMA_MINALIGN). Stop the redundant manual alignment. Besides cleaning up the code & avoiding needless work, this has the side effect of avoiding an arithmetic error found by Bryan on 64 bit systems due to the 32 bit size of the former dlinesz. This led the ready_count variable to have its upper 32b cleared erroneously for MIPS64 kernels, causing problems when ready_count was later used on MIPS64 via cpuidle. Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@imgtec.com> Reviewed-by:
-
James Hogan authored
commit 85423636 upstream. Since commit 81a76d71 ("MIPS: Avoid using unwind_stack() with usermode") show_backtrace() invokes the raw backtracer when cp0_status & ST0_KSU indicates user mode to fix issues on EVA kernels where user and kernel address spaces overlap. However this is used by show_stack() which creates its own pt_regs on the stack and leaves cp0_status uninitialised in most of the code paths. This results in the non deterministic use of the raw back tracer depending on the previous stack content. show_stack() deals exclusively with kernel mode stacks anyway, so explicitly initialise regs.cp0_status to KSU_KERNEL (i.e. 0) to ensure we get a useful backtrace. Fixes: 81a76d71 ("MIPS: Avoid using unwind_stack() with usermode") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16656/Signed-off-by:
-
David Rientjes authored
commit 460bcec8 upstream. We got need_resched() warnings in swap_cgroup_swapoff() because swap_cgroup_ctrl[type].length is particularly large. Reschedule when needed. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704061315270.80559@chino.kir.corp.google.comSigned-off-by:
David Rientjes <rientjes@google.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by:
-
Russell Currey authored
commit 71f677a9 upstream. The ast driver configures a window to enable access into BMC memory space in order to read some configuration registers. If this window is disabled, which it can be from the BMC side, the ast driver can't function. Closing this window is a necessity for security if a machine's host side and BMC side are controlled by different parties; i.e. a cloud provider offering machines "bare metal". A recent patch went in to try to check if that window is open but it does so by trying to access the registers in question and testing if the result is 0xffffffff. This method will trigger a PCIe error when the window is closed which on some systems will be fatal (it will trigger an EEH for example on POWER which will take out the device). This patch improves this in two ways: - First, if the firmware has put properties in the device-tree containing the relevant configuration information, we use these. - Otherwise, a bit in one of the SCU scratch registers (which are readable via the VGA register space and writeable by the BMC) will indicate if the BMC has closed the window. This bit has been defined by Y.C Chen from Aspeed. If the window is closed and the configuration isn't available from the device-tree, some sane defaults are used. Those defaults are hopefully sufficient for standard video modes used on a server. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Dave Airlie <airlied@redhat.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Kinglong Mee authored
commit 366a1569 upstream. Because nfs4_opendata_access() has close the state when access is denied, so the state isn't leak. Rather than revert the commit a974deee, I'd like clean the strange state close. [ 1615.094218] ------------[ cut here ]------------ [ 1615.094607] WARNING: CPU: 0 PID: 23702 at lib/list_debug.c:31 __list_add_valid+0x8e/0xa0 [ 1615.094913] list_add double add: new=ffff9d7901d9f608, prev=ffff9d7901d9f608, next=ffff9d7901ee8dd0. [ 1615.095458] Modules linked in: nfsv4(E) nfs(E) nfsd(E) tun bridge stp llc fuse ip_set nfnetlink vmw_vsock_vmci_transport vsock f2fs snd_seq_midi snd_seq_midi_event fscrypto coretemp ppdev crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_rapl_perf vmw_balloon snd_ens1371 joydev gameport snd_ac97_codec ac97_bus snd_seq snd_pcm snd_rawmidi snd_timer snd_seq_device snd soundcore nfit parport_pc parport acpi_cpufreq tpm_tis tpm_tis_core tpm i2c_piix4 vmw_vmci shpchp auth_rpcgss nfs_acl lockd(E) grace sunrpc(E) xfs libcrc32c vmwgfx drm_kms_helper ttm drm crc32c_intel mptspi e1000 serio_raw scsi_transport_spi mptscsih mptbase ata_generic pata_acpi fjes [last unloaded: nfs] [ 1615.097663] CPU: 0 PID: 23702 Comm: fstest Tainted: G W E 4.11.0-rc1+ #517 [ 1615.098015] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015 [ 1615.098807] Call Trace: [ 1615.099183] dump_stack+0x63/0x86 [ 1615.099578] __warn+0xcb/0xf0 [ 1615.099967] warn_slowpath_fmt+0x5f/0x80 [ 1615.100370] __list_add_valid+0x8e/0xa0 [ 1615.100760] nfs4_put_state_owner+0x75/0xc0 [nfsv4] [ 1615.101136] __nfs4_close+0x109/0x140 [nfsv4] [ 1615.101524] nfs4_close_state+0x15/0x20 [nfsv4] [ 1615.101949] nfs4_close_context+0x21/0x30 [nfsv4] [ 1615.102691] __put_nfs_open_context+0xb8/0x110 [nfs] [ 1615.103155] put_nfs_open_context+0x10/0x20 [nfs] [ 1615.103586] nfs4_file_open+0x13b/0x260 [nfsv4] [ 1615.103978] do_dentry_open+0x20a/0x2f0 [ 1615.104369] ? nfs4_copy_file_range+0x30/0x30 [nfsv4] [ 1615.104739] vfs_open+0x4c/0x70 [ 1615.105106] ? may_open+0x5a/0x100 [ 1615.105469] path_openat+0x623/0x1420 [ 1615.105823] do_filp_open+0x91/0x100 [ 1615.106174] ? __alloc_fd+0x3f/0x170 [ 1615.106568] do_sys_open+0x130/0x220 [ 1615.106920] ? __put_cred+0x3d/0x50 [ 1615.107256] SyS_open+0x1e/0x20 [ 1615.107588] entry_SYSCALL_64_fastpath+0x1a/0xa9 [ 1615.107922] RIP: 0033:0x7fab599069b0 [ 1615.108247] RSP: 002b:00007ffcf0600d78 EFLAGS: 00000246 ORIG_RAX: 0000000000000002 [ 1615.108575] RAX: ffffffffffffffda RBX: 00007fab59bcfae0 RCX: 00007fab599069b0 [ 1615.108896] RDX: 0000000000000200 RSI: 0000000000000200 RDI: 00007ffcf060255e [ 1615.109211] RBP: 0000000000040010 R08: 0000000000000000 R09: 0000000000000016 [ 1615.109515] R10: 00000000000006a1 R11: 0000000000000246 R12: 0000000000041000 [ 1615.109806] R13: 0000000000040010 R14: 0000000000001000 R15: 0000000000002710 [ 1615.110152] ---[ end trace 96ed63b1306bf2f3 ]--- Fixes: a974deee ("NFSv4: Fix memory and state leak in...") Signed-off-by:
Kinglong Mee <kinglongmee@gmail.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
