This patch contains 2 workaround for the System MMU v3.x.

System MMU v3.2 and v3.3 has FLPD cache that caches first level page
table entries to reduce page table walking latency. However, the
FLPD cache is filled with a first level page table entry even though
it is not accessed by a master H/W because System MMU v3.3
speculatively prefetches page table entries that may be accessed
in the near future by the master H/W.
The prefetched FLPD cache entries are not invalidated by iommu_unmap()
because iommu_unmap() only unmaps and invalidates the page table
entries that is mapped.

Because exynos-iommu driver discards a second level page table when
it needs to be replaced with another second level page table or
a first level page table entry with 1MB mapping, It is required to
invalidate FLPD cache that may contain the first level page table
entry that points to the second level page table.

Another workaround of System MMU v3.3 is initializing the first level
page table entries with the second level page table which is filled
with all zeros. This prevents System MMU prefetches 'fault' first
level page table entry which may lead page fault on access to 16MiB
wide.

System MMU 3.x fetches consecutive page table entries by a page
table walking to maximize bus utilization and to minimize TLB miss
panelty.
Unfortunately, functional problem is raised with the fetching behavior
because it fetches 'fault' page table entries that specifies no
translation information and that a valid translation information will
be written to in the near future. The logic in the System MMU generates
page fault with the cached fault entries that is no longer coherent
with the page table which is updated.

There is another workaround that must be implemented by I/O virtual
memory manager: any two consecutive I/O virtual memory area must have
a hole between the two that is larger than or equal to 128KiB.
Also, next I/O virtual memory area must be started from the next
128KiB boundary.

0            128K           256K               384K             512K
|-------------|---------------|-----------------|----------------|
|area1---------------->|.........hole...........|<--- area2 -----

The constraint is depicted above.
The size is selected by the calculation followed:
 - System MMU can fetch consecutive 64 page table entries at once
   64 * 4KiB = 256KiB. This is the size between 128K ~ 384K of the
   above picture. This style of fetching is 'block fetch'. It fetches
   the page table entries predefined consecutive page table entries
   including the entry that is the reason of the page table walking.
 - System MMU can prefetch upto consecutive 32 page table entries.
   This is the size between 256K ~ 384K.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This turns on FLPD_CACHE, ACGEN and SYSSEL.

FLPD_CACHE is a cache of 1st level page table entries that contains
the address of a 2nd level page table to reduce latency of page table
walking.

ACGEN is architectural clock gating that gates clocks by System MMU
itself if it is not active. Note that ACGEN is different from clock
gating by the CPU. ACGEN just gates clocks to the internal logic of
System MMU while clock gating by the CPU gates clocks to the System
MMU.

SYSSEL selects System MMU version in some Exynos SoCs. Some Exynos
SoCs have an option to select System MMU versions exclusively because
the SoCs adopts new System MMU version experimentally.

This also always selects LRU as TLB replacement policy. Selecting TLB
replacement policy is deprecated from System MMU 3.2. TLB in System
MMU 3.3 has single TLB replacement policy, LRU. The bit of MMU_CFG
selecting TLB replacement policy is remained as reserved.

QoS value of page table walking is set to 15 (highst value). System
MMU 3.3 can inherit QoS value of page table walking from its master
H/W's transaction. This new feature is enabled by default and QoS
value written to MMU_CFG is ignored.

This patch also adds simplifies the sysmmu version checking by
introducing some macros.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This commit adds device tree support for System MMU.

Also, system mmu handling is improved. Previously, an IOMMU domain is
bound to a System MMU which is not correct. This patch binds an IOMMU
domain with the master device of a System MMU.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This patch adds a description of the device tree binding for the
Samsung Exynos System MMU.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Some redundant error message is removed and some error messages
are changed to error level from debug level.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Patch written by Antonios Motakis <a.motakis@virtualopensystems.com>:

IOMMU groups are expected by certain users of the IOMMU API,
e.g. VFIO. Since each device is behind its own System MMU, we
can allocate a new IOMMU group for each device.
Reviewed-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Shaik Ameeer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This commit introduces sysmmu_pte_t for page table entries and
sysmmu_iova_t vor I/O virtual address that is manipulated by
exynos-iommu driver. The purpose of the typedef is to remove
dependencies to the driver code from the change of CPU architecture
from 32 bit to 64 bit.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Since acquiring read_lock is not more frequent than write_lock, it is
not beneficial to use rwlock, this commit changes rwlock to spinlock.
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This commit removes custom fault handler. The device drivers that
need to register fault handler can register
with iommu_set_fault_handler().

CC: Grant Grundler <grundler@chromium.org>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This patch gates clocks of master H/W as well as clocks of System MMU
if master clocks are specified.

Some Exynos SoCs (i.e. GScalers in Exynos5250) have dependencies in
the gating clocks of master H/W and its System MMU. If a H/W is the
case, accessing control registers of System MMU is prohibited unless
both of the gating clocks of System MMU and its master H/W.

CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This patch uses managed device helper functions in the probe().
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This patch removes dbgname member from sysmmu_drvdata structure.
Kernel message for debugging already has the name of a single
System MMU node. It also removes some compilation warnings.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Checking if the probing device has a parent device was just to discover
if the probing device is involved in a power domain when the power
domain controlled by Samsung's custom implementation.
Since generic IO power domain is applied, it is required to remove
the condition to see if the probing device has a parent device.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This commit adds cache flush for removed small and large page entries
in exynos_iommu_unmap(). Missing cache flush of removed page table
entries can cause missing page fault interrupt when a master IP
accesses an unmapped area.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Prefetch buffer is a cache of System MMU 3.x and caches a block of
page table entries to make effect of larger page with small pages.
However, how to control prefetch buffers and the specifications of
prefetch buffers different from minor versions of System MMU v3.
Prefetch buffers must be controled with care because there are some
restrictions in H/W design.

The interface and implementation to initiate prefetch buffers will
be prepared later.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

L2TLB is 8-way set-associative TLB with 512 entries. The number of
sets is 64.
A single 4KB(small page) translation information is cached
only to a set whose index is the same with the lower 6 bits of the page
frame number.
A single 64KB(large page) translation information can be
cached to any 16 sets whose top two bits of their indices are the same
with the bit [5:4] of the page frame number.
A single 1MB(section) or larger translation information can be cached to
any set in the TLB.

It is required to invalidate entire sets that may cache the target
translation information to guarantee that the L2TLB has no stale data.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Since kmalloc() does not guarantee that the allignment of 1KiB when it
allocates 1KiB, it is required to allocate lv2 page table from own
slab that guarantees alignment of 1KiB
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

This patch changes not to panic on any error when updating page table.
Instead prints error messages with callstack.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Commit 25e9d28d (ARM: EXYNOS: remove system mmu initialization from
exynos tree) removed arch/arm/mach-exynos/mach/sysmmu.h header without
removing remaining use of it from exynos-iommu driver, thus causing a
compilation error.

This patch fixes the error by removing respective include line
from exynos-iommu.c.

Use of __pa and __va macro is changed to virt_to_phys and phys_to_virt
which are recommended in driver code. printk formatting of physical
address is also fixed to %pa.

Also System MMU driver is changed to control only a single instance
of System MMU at a time. Since a single instance of System MMU has only
a single clock descriptor for its clock gating, single address range
for control registers, there is no need to obtain two or more clock
descriptors and ioremaped region.

CC: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>

Pull x86 fixes from Peter Anvin:
 "A somewhat unpleasantly large collection of small fixes.  The big ones
  are the __visible tree sweep and a fix for 'earlyprintk=efi,keep'.  It
  was using __init functions with predictably suboptimal results.

  Another key fix is a build fix which would produce output that simply
  would not decompress correctly in some configuration, due to the
  existing Makefiles picking up an unfortunate local label and mistaking
  it for the global symbol _end.

  Additional fixes include the handling of 64-bit numbers when setting
  the vdso data page (a latent bug which became manifest when i386
  started exporting a vdso with time functions), a fix to the new MSR
  manipulation accessors which would cause features to not get properly
  unblocked, a build fix for 32-bit userland, and a few new platform
  quirks"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, vdso, time: Cast tv_nsec to u64 for proper shifting in update_vsyscall()
  x86: Fix typo in MSR_IA32_MISC_ENABLE_LIMIT_CPUID macro
  x86: Fix typo preventing msr_set/clear_bit from having an effect
  x86/intel: Add quirk to disable HPET for the Baytrail platform
  x86/hpet: Make boot_hpet_disable extern
  x86-64, build: Fix stack protector Makefile breakage with 32-bit userland
  x86/reboot: Add reboot quirk for Certec BPC600
  asmlinkage: Add explicit __visible to drivers/*, lib/*, kernel/*
  asmlinkage, x86: Add explicit __visible to arch/x86/*
  asmlinkage: Revert "lto: Make asmlinkage __visible"
  x86, build: Don't get confused by local symbols
  x86/efi: earlyprintk=efi,keep fix

With tk->wall_to_monotonic.tv_nsec being a 32-bit value on 32-bit
systems, (tk->wall_to_monotonic.tv_nsec << tk->shift) in update_vsyscall()
may lose upper bits or, worse, add them since compiler will do this:
	(u64)(tk->wall_to_monotonic.tv_nsec << tk->shift)
instead of
	((u64)tk->wall_to_monotonic.tv_nsec << tk->shift)

So if, for example, tv_nsec is 0x800000 and shift is 8 we will end up
with 0xffffffff80000000 instead of 0x80000000. And then we are stuck in
the subsequent 'while' loop.

We need an explicit cast.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1399648287-15178-1-git-send-email-boris.ostrovsky@oracle.comAcked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

The spuriously added semicolon didn't have any effect because the
macro isn't currently in use.

c0a639adSigned-off-by: Andres Freund <andres@anarazel.de>
Link: http://lkml.kernel.org/r/1399598957-7011-3-git-send-email-andres@anarazel.de
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Due to a typo the msr accessor function introduced in
22085a66 didn't have any lasting
effects because they accidentally wrote the old value back.

After c0a639ad this at the very least
this causes cpuid limits not to be lifted on some cpus leading to
missing capabilities for those.
Signed-off-by: Andres Freund <andres@anarazel.de>
Link: http://lkml.kernel.org/r/1399598957-7011-2-git-send-email-andres@anarazel.de
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Pull xfs fixes from Dave Chinner:
 "The main fix is adding support for default ACLs on O_TMPFILE opened
  inodes to bring XFS into line with other filesystems.  Metadata CRCs
  are now also considered well enough tested to be fully supported, so
  we're removing the shouty warnings issued at mount time for
  filesystems with that format.  And there's transaction block
  reservation overrun fix.

  Summary:
   - fix a remote attribute size calculation bug that leads to a
     transaction overrun
   - add default ACLs to O_TMPFILE files
   - Remove the EXPERIMENTAL tag from filesystems with metadata CRC
     support"

* tag 'xfs-for-linus-3.15-rc5' of git://oss.sgi.com/xfs/xfs:
  xfs: remote attribute overwrite causes transaction overrun
  xfs: initialize default acls for ->tmpfile()
  xfs: fully support v5 format filesystems

Merge tag 'trace-fixes-v3.15-rc4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "This contains two fixes.

  The first is a long standing bug that causes bogus data to show up in
  the refcnt field of the module_refcnt tracepoint.  It was introduced
  by a merge conflict resolution back in 2.6.35-rc days.

  The result should be 'refcnt = incs - decs', but instead it did
  'refcnt = incs + decs'.

  The second fix is to a bug that was introduced in this merge window
  that allowed for a tracepoint funcs pointer to be used after it was
  freed.  Moving the location of where the probes are released solved
  the problem"

* tag 'trace-fixes-v3.15-rc4-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracepoint: Fix use of tracepoint funcs after rcu free
  trace: module: Maintain a valid user count

Pull input subsystem fixes from Dmitry Torokhov:
 "Just a few fixups to various drivers"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elantech - fix touchpad initialization on Gigabyte U2442
  Input: tca8418 - fix loading this driver as a module from a device tree
  Input: bma150 - extend chip detection for bma180
  Input: atkbd - fix keyboard not working on some LG laptops
  Input: synaptics - add min/max quirk for ThinkPad Edge E431

Pull sound fixes from Takashi Iwai:
 "A bunch of small fixes for USB-audio and HD-audio, where most of them
  are for regressions: USB-audio PM fixes, ratelimit annoyance fix, HDMI
  offline state fix, and a couple of device-specific quirks"

* tag 'sound-3.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - hdmi: Set converter channel count even without sink
  ALSA: usb-audio: work around corrupted TEAC UD-H01 feedback data
  ALSA: usb-audio: Fix deadlocks at resuming
  ALSA: usb-audio: Save mixer status only once at suspend
  ALSA: usb-audio: Prevent printk ratelimiting from spamming kernel log while DEBUG not defined
  ALSA: hda - add headset mic detect quirk for a Dell laptop

Pull mmc/rtsx revert from Lee Jones.

* tag 'mfd-mmc-fixes-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mmc: rtsx: Revert "mmc: rtsx: add support for pre_req and post_req"

Commit de7b2973 "tracepoint: Use struct pointer instead of name hash
for reg/unreg tracepoints" introduces a use after free by calling
release_probes on the old struct tracepoint array before the newly
allocated array is published with rcu_assign_pointer. There is a race
window where tracepoints (RCU readers) can perform a
"use-after-grace-period-after-free", which shows up as a GPF in
stress-tests.

Link: http://lkml.kernel.org/r/53698021.5020108@oracle.com
Link: http://lkml.kernel.org/p/1399549669-25465-1-git-send-email-mathieu.desnoyers@efficios.comReported-by: Sasha Levin <sasha.levin@oracle.com>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Dave Jones <davej@redhat.com>
Fixes: de7b2973 "tracepoint: Use struct pointer instead of name hash for reg/unreg tracepoints"
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

The replacement of the 'count' variable by two variables 'incs' and
'decs' to resolve some race conditions during module unloading was done
in parallel with some cleanup in the trace subsystem, and was integrated
as a merge.

Unfortunately, the formula for this replacement was wrong in the tracing
code, and the refcount in the traces was not usable as a result.

Use 'count = incs - decs' to compute the user count.

Link: http://lkml.kernel.org/p/1393924179-9147-1-git-send-email-romain.izard.pro@gmail.comAcked-by: Ingo Molnar <mingo@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: stable@vger.kernel.org # 2.6.35
Fixes: c1ab9cab "merge conflict resolution"
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

This reverts commit c42deffd.

commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.

The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

HPET on current Baytrail platform has accuracy problem to be
used as reliable clocksource/clockevent, so add a early quirk to
disable it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1398327498-13163-2-git-send-email-feng.tang@intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

HPET on some platform has accuracy problem. Making
"boot_hpet_disable" extern so that we can runtime disable
the HPET timer by using quirk to check the platform.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1398327498-13163-1-git-send-email-feng.tang@intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull MTD fix from Brian Norris:
 "A single update for Keystone SoC's, whose NAND controller does not
  support subpage programming"

* tag 'for-linus-20140507' of git://git.infradead.org/linux-mtd:
  mtd: davinci-nand: disable subpage write for keystone-nand

Pull HID fixes from Jiri Kosina:

 - fix a small bug in computation of report size, which might cause some
   devices (Atmel touchpad found on the Samsung Ativ 9) to reject
   reports with otherwise valid contents

 - a few device-ID specific quirks/additions piggy-backing on top of it

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: sensor-hub: Add in quirk for sensor hub in Lenovo Ideapad Yogas
  HID: add NO_INIT_REPORTS quirk for Synaptics Touch Pad V 103S
  HID: core: fix computation of the report size
  HID: multitouch: add support of EliteGroup 05D8 panels

Pull radeon mullins support from Dave Airlie:
 "This is support for the new AMD mullins APU, it pretty much just adds
  support to the driver in the all the right places, and is pretty low
  risk wrt other GPUs"

Oh well.  I guess it ends up fitting under "support new hardware" for
merging late.

* 'drm-radeon-mullins' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: add pci ids for Mullins
  drm/radeon: add Mullins VCE support
  drm/radeon: modesetting updates for Mullins.
  drm/radeon: dpm updates for KV/KB
  drm/radeon: add Mullins dpm support.
  drm/radeon: add Mullins UVD support.
  drm/radeon: update cik init for Mullins.
  drm/radeon: add Mullins chip family

Pull drm fixes from Dave Airlie:
 "radeon, i915 and nouveau fixes, all fixes for regressions or black
  screens, or possible oopses"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: lower the ref * post PLL maximum
  drm/radeon: check that we have a clock before PLL setup
  drm/radeon: drm/radeon: add missing radeon_semaphore_free to error path
  drm/radeon: Fix num_banks calculation for SI
  agp: info leak in agpioc_info_wrap()
  drm/gm107/gr: bump attrib cb size quite a bit
  drm/nouveau: fix another lock unbalance in nouveau_crtc_page_flip
  drm/nouveau/bios: fix shadowing from PROM on big-endian systems
  drm/nouveau/acpi: allow non-optimus setups to load vbios from acpi
  drm/radeon/dp: check for errors in dpcd reads
  drm/radeon: avoid high jitter with small frac divs
  drm/radeon: check buffer relocation offset
  drm/radeon: use pflip irq on R600+ v2
  drm/radeon/uvd: use lower clocks on old UVD to boot v2
  drm/i915: don't try DP_LINK_BW_5_4 on HSW ULX
  drm/i915: Sanitize the enable_ppgtt module option once
  drm/i915: Break encoder->crtc link separately in intel_sanitize_crtc()

If you are using a 64-bit kernel with 32-bit userland, then
scripts/gcc-x86_64-has-stack-protector.sh invokes 32-bit gcc
with -mcmodel=kernel, which produces:

<stdin>:1:0: error: code model 'kernel' not supported in the 32 bit mode

and trips the "broken compiler" test at arch/x86/Makefile:120.

There are several places a fix is possible, but the following seems
cleanest.  (But it's minimal; it would also be possible to factor
out a bunch of stuff from the two branches of the if.)
Signed-off-by: George Spelvin <linux@horizon.com>
Link: http://lkml.kernel.org/r/20140507210552.7581.qmail@ns.horizon.com
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Certec BPC600 needs reboot=pci to actually reboot.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1399446114-2147-1-git-send-email-christian.gmeiner@gmail.comSigned-off-by: Ingo Molnar <mingo@kernel.org>