Frontend dai_link id is used for closing ADM sessions.
During concurrent usecase when one session is closed,
it closes other ADM session associated with other usecase
too. Dai_link->id should always point to Frontend dai id.
Set cpu_dai id as dai_link id to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

sun8i-codec misses a route from ADC to AIF1 Slot 0 ADC. Add it
to the driver to avoid adding it to every dts.

Fixes: eda85d1f ("ASoC: sun8i-codec: Add ADC support for a33")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

On certain platforms, Display HDMI HDA codec was not going to sleep state
after the use when links are powered down after turning off the display
power. As per the HW recommendation, links are powered down before turning
off the display power to ensure that the codec goes to sleep state.

This patch was updated from an earlier version submitted upstream [1]
which conflicted with the changes merged for HDaudio codec support
with the Intel DSP.

[1] https://patchwork.kernel.org/patch/10540213/Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Stack memory isn't DMA-safe so it isn't safe to use either
regmap_raw_read or regmap_bulk_read to read into stack memory.

The two functions to read the scratch registers were using
stack memory and regmap_raw_read. It's not worth allocating
memory just for this trivial read, and it isn't time-critical.
A simple regmap_read for each register is sufficient.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds missing prepare_sleve_config that is needed for
setup the DMA slave channel for I2S.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>

drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().

Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()

Drop clk_disable_unprepare() calls for the same reason.

Fixes: 36c68493 ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

For some reason the dapm widgets are incorrectly defined from the start,
Not sure how we ended up with such thing. Fix them now!

Without this fix the backend dais are always powered up even if there
is no active stream.
Reported-by: Jimmy Cheng-Yi Chiang <cychiang@google.com>
Reported-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

q6asm routing gets added multiple times as part of dai probe.
Move this to q6routing routes which has those widgets defined, this also
fixes the issue where these are added each time at dai probe.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

SD line mask for MI2S starts from BIT 0 instead of BIT 1.
Fix all bit mask for MI2S SD lines.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some boards such as the Swanky model Chromebooks use pmc_plt_clk_0 for the
mclk instead of pmc_plt_clk_3.

This commit adds a DMI based quirk for this.

This fixing audio no longer working on these devices after
commit 648e9218 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case
of the Swanky that was breaking audio support since we were not using
the right clock in the cht_bsw_max98090_ti machine driver.

Cc: stable@vger.kernel.org
Fixes: 648e9218 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Dean Wallace <duffydack73@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

SND_SUN50I_CODEC_ANALOG selects SND_SUNXI_ADDA_PR_REGMAP which is leftover
of renaming SND_SUNXI_ADDA_PR_REGMAP to SND_SUN8I_ADDA_PR_REGMAP. Replace
it with SND_SUN8I_ADDA_PR_REGMAP to fix possible link errors for some
configurations:

sound/soc/sunxi/sun50i-codec-analog.o: In function `sun50i_codec_analog_probe':
sun50i-codec-analog.c:(.text+0x62): undefined reference to `sun8i_adda_pr_regmap_init'

Fixes: 42371f32 ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

commit 4d230d12 ("ASoC: rsnd: fixup not to call clk_get/set under
non-atomic") fixuped clock start timing. But it exchanged clock start
checker from ssi->usrcnt to ssi->rate.

Current rsnd_ssi_master_clk_start() is called from .prepare,
but some player (for example GStreamer) might calls it many times.
In such case, the checker might returns error even though it was not
error. It should check ssi->usrcnt instead of ssi->rate.
This patch fixup it. Without this patch, GStreamer can't switch
48kHz / 44.1kHz.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A kernel oops happens on an error case (usual missing BE mixer
configuration required by Intel SST driver). Git bisect points to this
macro and an operator precedence issue.

	for (; ((i--) >= 0) && ((dai) = rtd->codec_dais[i]);)

The initial code replaced by this macro was
	while (--i >= 0) {
		codec_dai = rtd->codec_dais[i];

Fix the C operator precedence difference by reverting to pre-decrement

Fixes: 0b7990e3 ('ASoC: add for_each_rtd_codec_dai() macro')
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

sound/soc/stm/stm32_sai_sub.c:393:26-32: ERROR: application of sizeof to pointer

 sizeof when applied to a pointer typed expression gives the size of
 the pointer

Generated by: scripts/coccinelle/misc/noderef.cocci

Fixes: 8307b2af ("ASoC: stm32: sai: set sai as mclk clock provider")
CC: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 8307b2af ("ASoC: stm32: sai: set sai as mclk clock provider")

Fix warning issued by strncat when bound equals to source length.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 8307b2af ("ASoC: stm32: sai: set sai as mclk clock provider")

Add COMMON_CLK dependency for STM32 SAI,
as it is required by clock provider.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

startup() and shutdown() hooks are called for both substreams,
so stopping either substream when another is running breaks the
latter.

E.g. playback breaks if capture is stopped when playback is running.

Move code from startup() and shutdown() to resume() and suspend()
hooks respectively to fix this issue
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The return type "unsigned int" was used by the wm2000_read()
function despite of the aspect that it will eventually return
a negative error code.
The resulting function doesn't add much to the code, so replace
wm2000_read with regmap_read.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The MCLK clock is made optional for cs42l51 codec.
However, ASoC DAPM clock supply widget, expects the clock to be defined
unconditionally.
Register MCLK DAPM conditionally in codec driver,
depending on clock presence in DT.

Fixes: 5e8d63a7 ("ASoC: cs42l51: add mclk support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Increase the address value width in the debug log from 4 digits to
8 digits to allow for DSP cores with larger memory address ranges.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The wm_adsp_buffer struct is the control header of a circular
buffer used to transfer data from the firmware over the
control interface to an ALSA compressed stream.

The original names of the fields pointing to the data buffer
were based on ADSP2V2 memory layout where they correspond to
{XM, XM, YM}. But this circular buffer could be used on other
types of DSP core that have different memory region types.
Also the names and description of the size fields were not
very clear. The field names and descriptions have been changed
to be generic and not imply any particular memory types.

This patch updates the wm_adsp driver to the new field names.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add MCLK dapm to allow configuration of cirrus CS42l51
codec as a master clock consumer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add master clock generation support in STM32 SAI.
The master clock provided by SAI can be used to feed a codec.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add clocks properties to cs42l51 Cirrus codec,
to support master clock provider.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

add mclk provider support to stm32 sai
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix a few trivial aka cosmetic only checkpatch issues like long lines,
wrong indentations, spurious blanks and newlines, missing newlines,
multi-line comments etc.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Currently, on power down for a CODEC to CODEC DAI link we only call
digital_mute and shutdown. Provide a little more flexibility for drivers
by adding a call to hw_free as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

I just added a couple missing tabs.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

R-Car datasheet is indicating that WS output settings of SSICR::SWSP
is inverted on TDM mode from non TDM mode settings.
But, it is meaning that TDM should use 0 here.
Without this patch, sound input/output 1ch will be 2ch, 2ch will be 3ch
..., be jumbled on I2S + TDM settings. This patch fixup it.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some SSIs are sharing each pins (= WS/CLK pin for playback/capture).
Then, SSI parent needs control WS/CLK setting for SSI slave.
In such case, SSI parent needs TDM settings if SSI slave is working as
TDM mode. But it is not cared in current driver.
It can't capture TDM sound without this patch if SSIs were pin sharing.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 with TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

LEFT_J / I2S only can use TDM.
commit 594680ea ("ASoC: pcm3168a: add hw constraint for channel")
commit 38096889 ("ASoC: pcm3168a: add HW constraint for non
RIGHT_J") added channel constraint for it, but, it was only for playback.
This patch adds constraint for capture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The STA32x chips feature an XTI clock input that needs to be stable before
the reset signal is released. Therefore, the chip driver needs to get a
handle to the clock. Instead of relying on other parts of the system to
enable the clock, let the codec driver grab a handle itself.

In order to keep existing boards working, clock support is made optional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add driver for NAU88C22.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Similar to the following:

commit 43217236 ("ASoC: tegra_alc5632: fix device_node refcounting")

commit 7c5dfd54 ("ASoC: tegra: fix device_node refcounting")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Allwinner A64 uses the same digital codec part as in A33, so we need
to build this driver on ARM64 as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The internal codec on A64 is split into 2 parts. The analog path controls
are routed through an embedded custom register bus accessed through
the PRCM block.

Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The internal codec on Allwinner A64 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block just as on A23/A33/H3.

Add a binding for this hardware.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

It will be reused by sun50i-codec-analog later.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

BCLK / LRCK ratio should be sample size * channels, but it was
hardcoded to 32 (0x1 is 32 as per A33 and A64 datasheets).

Calculate it basing on sample size and number of channels.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>