- 20 May, 2015 8 commits
-
-
Hans de Goede authored
Rename alps_set_abs_params_mt to alps_set_abs_params_semi_mt, to make it clear that it is only (to be) used for semi-mt devices. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
With the recent process_bitmap() changes all semi-mt devices always report the first finger down in slot 0, so stop using input-mt finger tracking for these. Signed-off-by:
-
Hans de Goede authored
All alps semi-mt touchpads give us the following data when 2 (or more) fingers are touching: 1 more or less accurate touch for the first finger down, and a bitmap with columns and rows in which 1 or more fingers are seen resulting in a crude (low res) bounding box. So far for v3, rushmore and v4 touchpads we've been reporting the coordinates of 2 opposite corners of the box when 2 fingers are touching. Ignoring the much better resolution data given in the normal position packet. This commit actually uses this data for the first touch, figures out which corner of the bounding box is closest to the first touch, and reports the coordinates of the opposite corner for the second touch, resulting in much better data for the first touch and for the single touch pointer-emulation events. This approach is similar to the one in alps_process_bitmap_dolphin, that function takes the single accurate touch info, calculates the distance to the center of the bounding box, and then puts the 2nd touch mirrored to the center. The downside of that approach is that if both touches move slowly in the same direction, the bounding box will stay the same for a while (as it is low res) and the second touch will thus been seen moving in the opposite direction until the bounding box actually changes, and then the second touch snaps to its new position resulting in a saw tooth pattern in the coordinates for the second touch, hence this new approach. This commit fixes 2 finger scrolling being choppy / jumpy on these touchpads. Signed-off-by:
-
Hans de Goede authored
We should decode the position packet before the packet with the bitmap data. This way we can use the more accurate position info in process_bitmap() to get better results. Signed-off-by:
-
Hans de Goede authored
Pinnacle / Rushmore packets contain either position info, or bitmap info, never both. So far we've in essence been storing garbage in the position / bitmap fields of the fields struct when decoding a bitmap / pos packet. We've been relying on the following sequence to get away with this: 1) Decode bitmap packet 2) Process bitmap packet 3) Decode position packet 4) Use position / button info This patch allows us to change this sequence, which will allow using the position info when processing the bitmap for more accurate results. Signed-off-by:
-
Hans de Goede authored
Change alps_decode_rushmore to do all decoding itself, rather then relying on alps_decode_pinnacle and then overriding some fields + or-ing in some bits. This is a preparation patch for modifying the decode functions to properly differentiate between position and bitmap packets. Signed-off-by:
-
Shailendra Verma authored
Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
-
Shailendra Verma authored
Signed-off-by:
-
- 15 May, 2015 7 commits
-
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
-
Evgeniy Dushistov authored
max7359_build_keycode() does the same thing as matrix_keypad_build_keymap(), but the latter can also handle DT bindings. Tested on beagleboard-xm. Signed-off-by:
Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by:
-
Evgeniy Dushistov authored
In datasheet of max7359 there is the following description of this flag: 0 - INT cleared when FIFO empty, 1 - INT cleared after host read. In this mode, I2C should read FIFO until interrupt condition removed, or further INT may be lost. So, if we set this flag, we have to read FIFO until it becomes empty. But in interrupt we read FIFO just once. This lead to "keyboard" hang until reboot, if we press several keys, because of interrupt handler read just one "press" from FIFO and clear interrupt. Signed-off-by: -
Pekka Enberg authored
Use kvfree() instead of open-coding it. Signed-off-by:
Pekka Enberg <penberg@kernel.org> Signed-off-by:
-
- 13 May, 2015 2 commits
-
-
Wei Yongjun authored
Remove duplicated include for acpi.h. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Wei Yongjun authored
Remove duplicated include for delay.h. Signed-off-by:
Heiko Stuebner <heiko.stuebner@bq.com> Signed-off-by:
-
- 08 May, 2015 5 commits
-
-
Dan Murphy authored
Add the TI drv2665 piezo haptic driver. This haptics IC requires the data to be streamed to the FIFO for continuous output. Datasheet can be found at: http://www.ti.com/product/drv2665Signed-off-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
-
Dan Murphy authored
Fix spelling of magnitude s/manginude/magnitude Signed-off-by:
-
Dan Murphy authored
Fix the Kconfig for the drv2667 as there was a copy/paste error. Signed-off-by:
-
Marek Vasut authored
Wait a little bit longer, 50mS instead of 20mS, until the driver starts polling for pen-up. The problematic behavior before this patch is applied is as follows. The behavior was observed on the STMPE610QTR controller. Upon a physical pen-down event, the touchscreen reports one set of x-y-p coordinates and a pen-down event. After that, the pen-up polling is triggered and since the controller is not ready yet, the polling mistakenly detects a pen-up event while the physical state is still such that the pen is down on the touch surface. The pen-up handling flushes the controller FIFO, so after that, all the samples in the controller are discarded. The controller becomes ready shortly after this bogus pen-up handling and does generate again a pen-down interrupt. This time, the controller contains x-y-p samples which all read as zero. Since pressure value is zero, this set of samples is effectively ignored by userland. In the end, the driver just bounces between pen-down and bogus pen-up handling, generating no useful results. Fix this by giving the controller a bit more time before polling it for pen-up. Signed-off-by:
Marek Vasut <marex@denx.de> Reviewed-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Marek Vasut authored
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much more explicit about it's behavior. We want to schedule the task 20 mS from now, so make it explicit in the code. Signed-off-by:
-
- 06 May, 2015 5 commits
-
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The platform_device_id is not modified by the driver and core uses it as const. Signed-off-by:
-
Paul Cercueil authored
The MSB of the first byte read via I2C at the coordinates address indicates whether the data is valid or ready (called "buffer status" in the datasheets) when an interrupt is raised. Previously, this bit was ignored, which resulted in a lot of incorrect detections of "finger removed" events. Signed-off-by:
Paul Cercueil <paul@crapouillou.net> Acked-by:
Bastien Nocera <hadess@hadess.net> Signed-off-by:
-
Guido Martínez authored
The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5 bits) in order to be capable of representing all FIFO length values from 0 to 16. This caused a problem: when the keypad reported 16 pending events the driver took it as 0, and did nothing. This in turn caused the keypad to re-issue the interrupt over and over again. Signed-off-by:
Guido Martínez <guido@vanguardiasur.com.ar> Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Signed-off-by:
-
Guido Martínez authored
The pull mask is created by looping each row (column) and building an 8-bit integer with the configuration. It is written byte-by-byte, when we reach the end of the rows (columns) or we're at the 3rd line (which finishes the first byte, since each pin is 2bits on the mask). However, this only works if we have at most 8 pins (2 bytes), which is not the case for the ADP5589. So, write the byte at each boundary (every 4 rows/columns). Signed-off-by:
-
- 20 Apr, 2015 5 commits
-
-
Wolfram Sang authored
My Pengutronix address is not valid anymore, redirect people to the Pengutronix kernel team. Reported-by:
Harald Geyer <harald@ccbib.org> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Acked-by:
Robert Schwebel <r.schwebel@pengutronix.de> Signed-off-by:
-
Dudley Du authored
The suspend scan rate value should not exceed 1000, unfortunately when implementing the limit we used max_t instead of min_t, causing the value to be at least 1000. Signed-off-by:
Dudley Du <dudl@cypress.com> Reviewed-by:
Benson Leung <bleung@chromium.org> Signed-off-by:
-
Duson Lin authored
According to Elan's firmware engineers we should not be subtracting 1 form the raw number of x and y traces so that the pitch size is correct. For example, if the touchpad x resolution is 2800 and x trace number is 20, the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36. Signed-off-by:
Duson Lin <dusonlin@emc.com.tw> Signed-off-by:
-
Duson Lin authored
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts the distance is reported as 0. Signed-off-by:
-
Dmitry Torokhov authored
Let's zero-extend hardware id number when forming firmware file name, to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which is quite unexpected. Acked-by: Charlie Mooney<charliemooney@chromium.org> Signed-off-by:
-
- 15 Apr, 2015 3 commits
-
-
Hans de Goede authored
Non interleaved dualpoint v2 devices have separate pointstick button bits, document this. Signed-off-by:
-
Dmitry Torokhov authored
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in Google Pixel 2 (2015). While newer version of ACPI standard allow use of device-tree-like properties in device descriptions, the version of ACPI implemented in Google BIOS does not support them, and we have to resort to DMI data to specify exact characteristics of the devices (touchpad vs. touchscreen, GPIO to button mapping, etc). Pixel 1 continues to use i2c devices and platform data created by chromeos-laptop driver, since ACPI does not enumerate them. Reviewed-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Tested-by:
-
Ming-ting Yao Wei authored
This adds rumble support for Xbox One controller by sending continuous rumble command. Trigger button rumbling is not yet implemented. Signed-off-by:
Ming-ting Yao Wei <mwei@lxde.org> Signed-off-by:
-
- 14 Apr, 2015 3 commits
-
-
Oliver Neukum authored
Replace old pr_* with dev_* debugging macros Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Thomas Hellstrom authored
VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU guests. By removing the guest cursor and using the host as a guest cursor the cursor movement appears instant although in reality there is some lag. To be able to do this, the host's view of the cursor position must exactly match the guest's view and an absolute pointer device is needed. Enter the VMMouse. While the VMMouse driver has historically been an Xorg user-space driver, implementing it as a kernel imput driver enables rootless Xorg and new compositing display servers for VMware guests. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by:
-
duson authored
Get pressure format flag from firmware to check if we need to normalize pressure data before reporting it. Signed-off-by:
-
- 11 Apr, 2015 2 commits
-
-
Dmitry Torokhov authored
To save people some time let's document that we do not want new quirks for "force-release" keys in the kernel and that they should patch userspace (udev) instead. Suggested-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
-
Fengguang Wu authored
Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Acked-by:
-
