- 12 Jan, 2010 3 commits
-
-
Zhao Yakui authored
For some SDVO cards based on conexant chip, we can't read the EDID if we don't read the response after issuing SDVO DDC bus switch command. From the SDVO spec once when another I2C transaction is finished after completing the I2C transaction of issuing the bus switch command, it will be switched back to the SDVO internal state again. So we can't initiate a new I2C transaction to read the response after issuing the DDC bus switch command. Instead we should issue DDC bus switch command and read the response in the same I2C transaction. https://bugs.freedesktop.org/show_bug.cgi?id=23842 https://bugs.freedesktop.org/show_bug.cgi?id=24458 https://bugs.freedesktop.org/show_bug.cgi?id=24522 https://bugs.freedesktop.org/show_bug.cgi?id=24282Signed-off-by:
Zhao Yakui <yakui.zhao@intel.com> Tested-by:
Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca> Signed-off-by:
Eric Anholt <eric@anholt.net>
-
Zhao Yakui authored
On some boxes the BIOS will report different child device arrays when the system is booted with/without the dock. In such case the HDMI/DP port can't be setup correctly. So revert two commits (fc816655/ 6e36595a) that use the child device parsed from VBT to setup HDMI/DP. http://bugzilla.kernel.org/show_bug.cgi?id=14854 http://bugzilla.kernel.org/show_bug.cgi?id=14860Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Rafael J. Wysocki authored
Commit cbda12d7 (drm/i915: implement new pm ops for i915), among other things, removed the .suspend and .resume pointers from the struct drm_driver object in i915_drv.c, which broke resume without KMS on my MSI Wind U100. Fix this by reverting that part of commit cbda12d7. Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl> Acked-by:
Jesse Barnes <jbarnes@virtuousgeek.org> [anholt: added comment explaining when .suspend/.resume matter] Signed-off-by:
-
- 07 Jan, 2010 22 commits
-
-
Zhao Yakui authored
Without this fix, some modes couldn't find appropriate clocks. Signed-off-by:
Matthew Garrett <mjg@redhat.com>
-
Zhao Yakui authored
For any given clock we can use the find_pll to get the corresponding DPLL setting. It is unnecessary to use the find_reduce_pll callback function to calculate the DPLL parameter for LVDS downclock in order to get the same divider factor(P) for the normal and downclock. In theory when the LVDS downclock is supported by LVDS panel, we should get the same DPLL divider factor(P) for the normal clock and reduced downclock. If we get the diferent divider factor(P) for normal clock and reduced downclock, it means that the found downclock is incorrect and should be discarded. So we should use find_pll callback to calculate the DPLL parameter for the LVDS reduced downclock as for the normal clock. Then we can do the cleanup about find_reduced_pll. Signed-off-by:
-
Zhao Yakui authored
The HP comaq nx9020/Samsung SX20S laptop always report that the LID status is closed and we can't use it reliabily for LVDS detection. So add the two boxes into the quirk list. http://bugzilla.kernel.org/show_bug.cgi?id=14957 http://bugzilla.kernel.org/show_bug.cgi?id=14554Signed-off-by:
-
Zhenyu Wang authored
As we removed TV hotplug, don't check its status ever. Reviewed-by:
Adam Jackson <ajax@redhat.com> Signed-off-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/radeon/kms: rs600: use correct mask for SW interrupt gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test drm/radeon/radeon_device.c: move a dereference below a NULL test drm/radeon/radeon_fence.c: move a dereference below the NULL test drm/radeon/radeon_connectors.c: add a NULL test before dereference drm/radeon/kms: fix memory leak drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line() drm/edid: Fix CVT width/height decode drm/edid: Skip empty CVT codepoints drm: remove address mask param for drm_pci_alloc() drm/radeon/kms: add missing breaks in i2c and ss lookups drm/radeon/kms: add primary dac adj values table drm/radeon/kms: fallback to default connector table
-
Dave Airlie authored
* korg/drm-radeon-next: drm/radeon/kms: rs600: use correct mask for SW interrupt gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test drm/radeon/radeon_device.c: move a dereference below a NULL test drm/radeon/radeon_fence.c: move a dereference below the NULL test drm/radeon/radeon_connectors.c: add a NULL test before dereference drm/radeon/kms: fix memory leak drm/radeon/kms: add missing breaks in i2c and ss lookups drm/radeon/kms: add primary dac adj values table drm/radeon/kms: fallback to default connector table
-
Luca Tettamanti authored
The mask happens to be the same, but the IH is reading the status, not the not the control register. Signed-off-by:
Luca Tettamanti <kronos.it@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
Darren Jenkins authored
If a NULL value is possible, the dereference should only occur after the NULL test. Coverity CID: 13338 Signed-off-by:
Darren Jenkins <darrenrjenkins@gmail.com> Signed-off-by:
-
Darren Jenkins authored
If a NULL value is possible, the dereference should only occur after the NULL test. Coverity CID: 13335 Signed-off-by:
-
Darren Jenkins authored
If a NULL value is possible, the dereference should only occur after the NULL test. Coverity CID: 13334 Signed-off-by:
-
Darren Jenkins authored
The encoder variable can be NULL in this function so I believe it should be checked before dereference. Coverity CID: 13253 [airlied: extremely unlikely to happen] Signed-off-by:
-
Jiri Slaby authored
Stanse found a memory leak in radeon_master_create. master_priv is not freed/assigned on all paths. Fix that. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Dave Airlie authored
* drm-core-next: drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line() drm/edid: Fix CVT width/height decode drm/edid: Skip empty CVT codepoints drm: remove address mask param for drm_pci_alloc()
-
Roel Kluin authored
This always evaluates to true. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Adam Jackson authored
Signed-off-by:
-
Adam Jackson authored
Signed-off-by:
-
Zhenyu Wang authored
drm_pci_alloc() has input of address mask for setting pci dma mask on the device, which should be properly setup by drm driver. And leave it as a param for drm_pci_alloc() would cause confusion or mistake would corrupt the correct dma mask setting, as seen on intel hw which set wrong dma mask for hw status page. So remove it from drm_pci_alloc() function. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intelLinus Torvalds authored
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits) drm/i915: remove full registers dump debug drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function drm/i915: Select the correct BPC for LVDS on Ironlake drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake drm/i915: Enable/disable the dithering for LVDS based on VBT setting drm/i915: Permit pinning whilst the device is 'suspended' drm/i915: Hold struct mutex whilst pinning power context bo. drm/i915: fix unused var drm/i915: Storage class should be before const qualifier drm/i915: remove render reclock support drm/i915: Fix RC6 suspend/resume drm/i915: execbuf2 support drm/i915: Reload hangcheck timer too for Ironlake drm/i915: only enable hotplug for detected outputs drm/i915: Track whether cursor needs physical address in intel_device_info drm/i915: Implement IS_* macros using static tables drm/i915: Move PCI IDs into i915 driver drm/i915: Update LVDS connector status when receiving ACPI LID event drm/i915: Add MALATA PC-81005 to ACPI LID quirk list drm/i915: implement new pm ops for i915 ...
-
Jie Zhang authored
The MMU code uses the copy_*_user_page() variants in access_process_vm() rather than copy_*_user() as the former includes an icache flush. This is important when doing things like setting software breakpoints with gdb. So switch the NOMMU code over to do the same. This patch makes the reasonable assumption that copy_from_user_page() won't fail - which is probably fine, as we've checked the VMA from which we're copying is usable, and the copy is not allowed to cross VMAs. The one case where it might go wrong is if the VMA is a device rather than RAM, and that device returns an error which - in which case rubbish will be returned rather than EIO. Signed-off-by:
Jie Zhang <jie.zhang@analog.com> Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
David Howells <dhowells@redhat.com> Acked-by:
David McCullough <david_mccullough@mcafee.com> Acked-by:
Paul Mundt <lethal@linux-sh.org> Acked-by:
Greg Ungerer <gerg@uclinux.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Mike Frysinger authored
When working with FDPIC, there are many shared mappings of read-only code regions between applications (the C library, applet packages like busybox, etc.), but the current do_mmap_pgoff() function will issue an icache flush whenever a VMA is added to an MM instead of only doing it when the map is initially created. The flush can instead be done when a region is first mmapped PROT_EXEC. Note that we may not rely on the first mapping of a region being executable - it's possible for it to be PROT_READ only, so we have to remember whether we've flushed the region or not, and then flush the entire region when a bit of it is made executable. However, this also affects the brk area. That will no longer be executable. We can mprotect() it to PROT_EXEC on MPU-mode kernels, but for NOMMU mode kernels, when it increases the brk allocation, making sys_brk() flush the extra from the icache should suffice. The brk area probably isn't used by NOMMU programs since the brk area can only use up the leavings from the stack allocation, where the stack allocation is larger than requested. Signed-off-by:
-
Mike Frysinger authored
The current code will load the stack size and protection markings, but then only use the markings in the MMU code path. The NOMMU code path always passes PROT_EXEC to the mmap() call. While this doesn't matter to most people whilst the code is running, it will cause a pointless icache flush when starting every FDPIC application. Typically this icache flush will be of a region on the order of 128KB in size, or may be the entire icache, depending on the facilities available on the CPU. In the case where the arch default behaviour seems to be desired (EXSTACK_DEFAULT), we probe VM_STACK_FLAGS for VM_EXEC to determine whether we should be setting PROT_EXEC or not. For arches that support an MPU (Memory Protection Unit - an MMU without the virtual mapping capability), setting PROT_EXEC or not will make an important difference. It should be noted that this change also affects the executability of the brk region, since ELF-FDPIC has that share with the stack. However, this is probably irrelevant as NOMMU programs aren't likely to use the brk region, preferring instead allocation via mmap(). Signed-off-by:
-
git://linux-nfs.org/~bfields/linuxLinus Torvalds authored
* 'for-2.6.33' of git://linux-nfs.org/~bfields/linux: sunrpc: fix peername failed on closed listener nfsd: make sure data is on disk before calling ->fsync nfsd: fix "insecure" export option
-
- 06 Jan, 2010 15 commits
-
-
Xiaotian Feng authored
There're some warnings of "nfsd: peername failed (err 107)!" socket error -107 means Transport endpoint is not connected. This warning message was outputed by svc_tcp_accept() [net/sunrpc/svcsock.c], when kernel_getpeername returns -107. This means socket might be CLOSED. And svc_tcp_accept was called by svc_recv() [net/sunrpc/svc_xprt.c] if (test_bit(XPT_LISTENER, &xprt->xpt_flags)) { <snip> newxpt = xprt->xpt_ops->xpo_accept(xprt); <snip> So this might happen when xprt->xpt_flags has both XPT_LISTENER and XPT_CLOSE. Let's take a look at commit b0401d72, this commit has moved the close processing after do recvfrom method, but this commit also introduces this warnings, if the xpt_flags has both XPT_LISTENER and XPT_CLOSED, we should close it, not accpet then close. Signed-off-by:Xiaotian Feng <dfeng@redhat.com> Cc: J. Bruce Fields <bfields@fieldses.org> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Cc: David S. Miller <davem@davemloft.net> Cc: stable@kernel.org Signed-off-by:
J. Bruce Fields <bfields@citi.umich.edu>
-
Christoph Hellwig authored
nfsd is not using vfs_fsync, so I missed it when changing the calling convention during the 2.6.32 window. This patch fixes it to not only start the data writeout, but also wait for it to complete before calling into ->fsync. Signed-off-by:
Christoph Hellwig <hch@lst.de> Cc: stable@kernel.org Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinciLinus Torvalds authored
* 'davinci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: DaVinci: DM365: Add the device_enable for the DaVinci Keyscan davinci: enable ARCH_HAS_HOLES_MEMORYMODEL for DaVinci davinci: da8xx/omap-l1: mark RTC as a wakeup source davinci: cp_intc: provide set_wake function Davinci VPFE Capture: Take i2c adapter id through platform data
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] lpfc 8.3.7: Update Driver version to 8.3.7 [SCSI] lpfc 8.3.7: Fix discovery failures. [SCSI] lpfc 8.3.7: Fix SCSI protocol related errors. [SCSI] lpfc 8.3.7: Fix hardware/SLI relates issues [SCSI] lpfc 8.3.7: Fix NPIV operation errors [SCSI] lpfc 8.3.7: Fix FC protocol errors [SCSI] stex: fix scan of nonexistent lun [SCSI] pmcraid: fix to avoid twice scsi_dma_unmap for a command [SCSI] qla2xxx: Update version number to 8.03.01-k9. [SCSI] qla2xxx: Added to EEH support. [SCSI] qla2xxx: Extend base EEH support in qla2xxx. [SCSI] qla2xxx: Fix for a multiqueue bug in CPU affinity mode [SCSI] qla2xxx: Get the link data rate explicitly during device resync. [SCSI] cxgb3i: Fix a login over vlan issue
-
Zhenyu Wang authored
This one reverts 9e3a6d15. As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485, this dump will cause hang problem on some machine. If something really needs this kind of full registers dump, that could be done within intel-gpu-tools. Cc: Ben Gamari <bgamari.foss@gmail.com> Signed-off-by:
-
Zhao Yakui authored
For some clocks, the old Ironlake DPLL calculator wold give m/n/p combinations that didn't match the spreadsheet of what HW validation tests. Instead, use the G4X DPLL calculator, which does a better job at it. So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS on ironlake. At the same time to consider the dpll setting for display port, we add the display port DPLL limit on ironlake, which will directly use the function of intel_find_pll_ironlake_dp to get the corresponding dpll setting. Signed-off-by:
-
Zhao Yakui authored
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel, the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8. At the same time the BPC will be 8 when the output device is CRT/HDMI/DP. Signed-off-by:
-
Zhao Yakui authored
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake. Signed-off-by:
-
Zhao Yakui authored
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x platform the dithering flag is defined in LVDS register. And on the ironlake the dithering flag is defined in pipeconf register. Signed-off-by:
-
Chris Wilson authored
As pinning (allocating and binding GTT memory) does not actually invoke GPU commands, it is safe, and indeed is attempted, during resumption from suspension: [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16 Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Reported-by:
Hugh Dickins <hugh.dickins@tiscali.co.uk> Cc: stable@kernel.org Signed-off-by:
-
Chris Wilson authored
Hugh found an error path where we were attempting to unref a bo without holding the struct mutex: [drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16 ------------[ cut here ]------------ WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e() Hardware name: ESPRIMO Mobile V5505 Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4 Call Trace: [<7815298e>] warn_slowpath_common+0x59/0x6b [<781529b3>] warn_slowpath_null+0x13/0x18 [<78317c1a>] ? drm_gem_object_free+0x20/0x5e [<78317c1a>] drm_gem_object_free+0x20/0x5e [<78317bfa>] ? drm_gem_object_free+0x0/0x5e [<7829df11>] kref_put+0x38/0x45 [<7833a5f0>] intel_init_clock_gating+0x232/0x271 [<78317bfa>] ? drm_gem_object_free+0x0/0x5e [<7832c307>] i915_restore_state+0x21a/0x2b3 [<7832379d>] i915_resume+0x3c/0xbb [<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123 [<7831c756>] ? drm_class_resume+0x0/0x3e [<7831c78d>] drm_class_resume+0x37/0x3e [<78351e0a>] legacy_resume+0x1e/0x51 [<78351ece>] device_resume+0x91/0xab [<7831c756>] ? drm_class_resume+0x0/0x3e [<78352226>] dpm_resume+0x58/0x10f [<783522fb>] dpm_resume_end+0x1e/0x2c [<78180f80>] suspend_devices_and_enter+0x61/0x84 [<78180ff8>] enter_state+0x55/0x83 [<7818091c>] state_store+0x94/0xaa [<7829d09e>] kobj_attr_store+0x1e/0x23 [<782098e0>] sysfs_write_file+0x66/0x99 [<781cd2f0>] vfs_write+0x8a/0x108 [<781cd408>] sys_write+0x3c/0x63 [<78125c10>] sysenter_do_call+0x12/0x36 ---[ end trace a343537f29950fda ]--- It is in fact slightly more insiduous that first appears since we are attempting to not just free the object without the lock, but are trying to do the whole bo manipulation without holding the lock. Reported-by:
-
Andrew Morton authored
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load': drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function Partly this is because gcc isn't smart enough. But `ll_base' does get used uninitialised in the DRM_DEBUG() call. Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Eric Anholt <eric@anholt.net> Cc: Dave Airlie <airlied@linux.ie> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Tobias Klauser authored
The C99 specification states in section 6.11.5: The placement of a storage-class specifier other than at the beginning of the declaration specifiers in a declaration is an obsolescent feature. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Signed-off-by:
-
Jesse Barnes authored
This code generally fails to adjust the render clock, and when it does, it conflicts with some other register settings and can cause problems. So remove this code altogether. I'm reworking it now to do the right thing, but the only bit it will share is the VBT check for whether reclocking is supported, so I'm leaving that bit. Reverts most of 652c393a ("add dynamic clock frequency control"), though for many the regressions showed up in the later 181a5336 ("Fix render reclock availability detection"). Signed-off-by:
-
Andrew Lutomirski authored
We restored RC6 twice on resume, even with modesetting off. Instead, only restore it once and skip RC6 initialization entirely in non-KMS mode. Signed-off-by:
Andy Lutomirski <luto@mit.edu> Tested-by:
Jeff Chua <jeff.chua.linux@gmail.com> Signed-off-by:
-
