- 10 Mar, 2017 17 commits
-
-
Doug Berger authored
When using the internal PHY it must be powered up when the MII is probed or the PHY will not be detected. Since the PHY is powered up at reset this has not been a problem. However, when the kernel is restarted with kexec the PHY will likely be powered down when the kernel starts so it will not be detected and the Ethernet link will not be established. This commit explicitly powers up the internal PHY when the GENET driver is probed to correct this behavior. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Doug Berger <opendmb@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Doug Berger authored
Add a spinlock to ensure that irq0_stat is not unintentionally altered as the result of preemption. Also removed unserviced irq0 interrupts and removed irq1_stat since there is no bottom half service for those interrupts. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Doug Berger authored
Since the internal PHY is powered up during the open and resume functions it should be powered back down if the functions fail. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Doug Berger authored
The reserved gphy_rev value of 0x01ff must be tested before the old or new scheme for GPHY major versioning are tested, otherwise it will be treated as 0xff00 according to the old scheme. Fixes: b04a2f5b ("net: bcmgenet: add support for new GENET PHY revision scheme") Signed-off-by:
-
Doug Berger authored
The gap between the Tx status counters and the Rx RUNT counters is now being added to allow correct reporting of the registers. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Doug Berger authored
The location of the RBUF overflow and error counters has moved between different version of the GENET MAC. This commit corrects the driver to read from the correct locations depending on the version of the GENET MAC. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
Lendacky, Thomas authored
Depending on the hardware, the amd-xgbe driver may use disable_irq_nosync() and enable_irq() when an interrupt is received to process Rx packets. If the napi_complete_done() return value isn't checked an unbalanced enable for the IRQ could result, generating a warning stack trace. Update the driver to only enable interrupts if napi_complete_done() returns true. Reported-by:
Jeremy Linton <jeremy.linton@arm.com> Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
-
David Howells authored
If rxrpc_kernel_send_data() is asked to send data through a call that has already failed (due to a remote abort, received protocol error or network error), then return the associated error code saved in the call rather than ESHUTDOWN. This allows the caller to work out whether to ask for the abort code or not based on this. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Alexey Kodanev authored
commit c146066a ("ipv4: Don't use ufo handling on later transformed packets") and commit f89c56ce ("ipv6: Don't use ufo handling on later transformed packets") added a check that 'rt->dst.header_len' isn't zero in order to skip UFO, but it doesn't include IPcomp in transport mode where it equals zero. Packets, after payload compression, may not require further fragmentation, and if original length exceeds MTU, later compressed packets will be transmitted incorrectly. This can be reproduced with LTP udp_ipsec.sh test on veth device with enabled UFO, MTU is 1500 and UDP payload is 2000: * IPv4 case, offset is wrong + unnecessary fragmentation udp_ipsec.sh -p comp -m transport -s 2000 & tcpdump -ni ltp_ns_veth2 ... IP (tos 0x0, ttl 64, id 45203, offset 0, flags [+], proto Compressed IP (108), length 49) 10.0.0.2 > 10.0.0.1: IPComp(cpi=0x1000) IP (tos 0x0, ttl 64, id 45203, offset 1480, flags [none], proto UDP (17), length 21) 10.0.0.2 > 10.0.0.1: ip-proto-17 * IPv6 case, sending small fragments udp_ipsec.sh -6 -p comp -m transport -s 2000 & tcpdump -ni ltp_ns_veth2 ... IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108) payload length: 37) fd00::2 > fd00::1: IPComp(cpi=0x1000) IP6 (flowlabel 0x6b9ba, hlim 64, next-header Compressed IP (108) payload length: 21) fd00::2 > fd00::1: IPComp(cpi=0x1000) Fix it by checking 'rt->dst.xfrm' pointer to 'xfrm_state' struct, skip UFO if xfrm is set. So the new check will include both cases: IPcomp and IPsec. Fixes: c146066a ("ipv4: Don't use ufo handling on later transformed packets") Fixes: f89c56ce ("ipv6: Don't use ufo handling on later transformed packets") Signed-off-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by:
-
David Howells authored
Lockdep issues a circular dependency warning when AFS issues an operation through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem. The theory lockdep comes up with is as follows: (1) If the pagefault handler decides it needs to read pages from AFS, it calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but creating a call requires the socket lock: mmap_sem must be taken before sk_lock-AF_RXRPC (2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind() binds the underlying UDP socket whilst holding its socket lock. inet_bind() takes its own socket lock: sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET (3) Reading from a TCP socket into a userspace buffer might cause a fault and thus cause the kernel to take the mmap_sem, but the TCP socket is locked whilst doing this: sk_lock-AF_INET must be taken before mmap_sem However, lockdep's theory is wrong in this instance because it deals only with lock classes and not individual locks. The AF_INET lock in (2) isn't really equivalent to the AF_INET lock in (3) as the former deals with a socket entirely internal to the kernel that never sees userspace. This is a limitation in the design of lockdep. Fix the general case by: (1) Double up all the locking keys used in sockets so that one set are used if the socket is created by userspace and the other set is used if the socket is created by the kernel. (2) Store the kern parameter passed to sk_alloc() in a variable in the sock struct (sk_kern_sock). This informs sock_lock_init(), sock_init_data() and sk_clone_lock() as to the lock keys to be used. Note that the child created by sk_clone_lock() inherits the parent's kern setting. (3) Add a 'kern' parameter to ->accept() that is analogous to the one passed in to ->create() that distinguishes whether kernel_accept() or sys_accept4() was the caller and can be passed to sk_alloc(). Note that a lot of accept functions merely dequeue an already allocated socket. I haven't touched these as the new socket already exists before we get the parameter. Note also that there are a couple of places where I've made the accepted socket unconditionally kernel-based: irda_accept() rds_rcp_accept_one() tcp_accept_from_sock() because they follow a sock_create_kern() and accept off of that. Whilst creating this, I noticed that lustre and ocfs don't create sockets through sock_create_kern() and thus they aren't marked as for-kernel, though they appear to be internal. I wonder if these should do that so that they use the new set of lock keys. Signed-off-by: -
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Misc. small fixes. Fixes include moving the initial function reset, notifying the RDMA driver during tx timeout, setting dcbx_cap properly depending on whether the firmware agent is running or not, and an autoneg related improvement. ==================== Signed-off-by: -
Michael Chan authored
In some situations, the firmware will return 0 for autoneg supported speed. This may happen if the firmware detects no SFP module, for example. The driver should ignore this so that we don't end up with an invalid autoneg setting with nothing advertised. When SFP module is inserted, we'll get the updated settings from firmware at that time. Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Set DCB_CAP_DCBX_HOST capability flag only if the firmware LLDP agent is not running. Signed-off-by:
-
Michael Chan authored
If we call bnxt_reset_task() due to tx timeout, we should call bnxt_ulp_stop() to inform the RDMA driver about the error and the impending reset. Signed-off-by:
-
Michael Chan authored
The firmware call to do function reset is done too late. It is causing the rings that have been reserved to be freed. In NPAR mode, this bug is causing us to run out of rings. Fixes: 391be5c2 ("bnxt_en: Implement new scheme to reserve tx rings.") Signed-off-by:
-
LABBE Corentin authored
Printing copyright does not give any useful information on the boot process. Furthermore, the email address printed is obsolete since commit ba57b6f2 ("MAINTAINERS: fix bouncing tun/tap entries") Signed-off-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by:
-
Alexander Potapenko authored
KMSAN reports a use of uninitialized memory in put_cmsg() because msg.msg_flags in recvfrom haven't been initialized properly. The flag values don't affect the result on this path, but it's still a good idea to initialize them explicitly. Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
- 09 Mar, 2017 23 commits
-
-
David S. Miller authored
Alexei Starovoitov says: ==================== bpf: htab fixes Two bpf hashtable fixes. See individual patches for details. ==================== Signed-off-by: -
Alexei Starovoitov authored
when all map elements are pre-allocated one cpu can delete and reuse htab_elem while another cpu is still walking the hlist. In such case the lookup may miss the element. Convert hlist to hlist_nulls to avoid such scenario. When bucket lock is taken there is no need to take such precautions, so only convert map_lookup and map_get_next to nulls. The race window is extremely small and only reproducible with explicit udelay() inside lookup_nulls_elem_raw() Similar to hlist add hlist_nulls_for_each_entry_safe() and hlist_nulls_entry_safe() helpers. Fixes: 6c905981 ("bpf: pre-allocate hash map elements") Reported-by:
Jonathan Perry <jonperry@fb.com> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Alexei Starovoitov authored
when htab_elem is removed from the bucket list the htab_elem.hash_node.next field should not be overridden too early otherwise we have a tiny race window between lookup and delete. The bug was discovered by manual code analysis and reproducible only with explicit udelay() in lookup_elem_raw(). Fixes: 6c905981 ("bpf: pre-allocate hash map elements") Reported-by:
-
Dmitry V. Levin authored
Replace MAX_ADDR_LEN with its numeric value to fix the following linux/packet_diag.h userspace compilation error: /usr/include/linux/packet_diag.h:67:17: error: 'MAX_ADDR_LEN' undeclared here (not in a function) __u8 pdmc_addr[MAX_ADDR_LEN]; This is not the first case in the UAPI where the numeric value of MAX_ADDR_LEN is used instead of symbolic one, uapi/linux/if_link.h already does the same: $ grep MAX_ADDR_LEN include/uapi/linux/if_link.h __u8 mac[32]; /* MAX_ADDR_LEN */ There are no UAPI headers besides these two that use MAX_ADDR_LEN. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Pavel Emelyanov <xemul@virtuozzo.com> Signed-off-by:
-
Paolo Abeni authored
The gso code of several tunnels type (gre and udp tunnels) takes for granted that the skb->inner_protocol is properly initialized and drops the packet elsewhere. On the forwarding path no one is initializing such field, so gro encapsulated packets are dropped on forward. Since commit 38720352 ("gre: Use inner_proto to obtain inner header protocol"), this can be reproduced when the encapsulated packets use gre as the tunneling protocol. The issue happens also with vxlan and geneve tunnels since commit 8bce6d7d ("udp: Generalize skb_udp_segment"), if the forwarding host's ingress nic has h/w offload for such tunnel and a vxlan/geneve device is configured on top of it, regardless of the configured peer address and vni. To address the issue, this change initialize the inner_protocol field for encapsulated packets in both ipv4 and ipv6 gro complete callbacks. Fixes: 38720352 ("gre: Use inner_proto to obtain inner header protocol") Fixes: 8bce6d7d ("udp: Generalize skb_udp_segment") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
-
robert.foss@collabora.com authored
In qed_ll2_start_ooo() the ll2_info variable is uninitialized and then passed to qed_ll2_acquire_connection() where it is copied into a new memory space. This shouldn't cause any issue as long as non of the copied memory is every read. But the potential for a bug being introduced by reading this memory is real. Detected by CoverityScan, CID#1399632 ("Uninitialized scalar variable") Signed-off-by:Robert Foss <robert.foss@collabora.com> Signed-off-by:
-
David S. Miller authored
Sunil Goutham says: ==================== net: thunderx: Miscellaneous fixes This patch set fixes multiple issues such as IOMMU translation faults when kernel is booted with IOMMU enabled on host, incorrect MAC ID reading from ACPI tables and IPv6 UDP packet drop due to failure of checksum validation. Changes from v1: - As suggested by David Miller, got rid of conditional calling of DMA map/unmap APIs. Also updated commit message in 'IOMMU translation faults' patch. ==================== Signed-off-by: -
Thanneeru Srinivasulu authored
Do not consider IPv6 frames with zero UDP checksum as frames with bad checksum and drop them. Signed-off-by:
Thanneeru Srinivasulu <tsrinivasulu@cavium.com> Signed-off-by:
Sunil Goutham <sgoutham@cavium.com> Signed-off-by:
-
Sunil Goutham authored
When booted with ACPI, random mac addresses are being assigned to node1 interfaces due to mismatch of bgx_id in BGX driver and ACPI tables. This patch fixes this issue by setting maximum BGX devices per node based on platform/soc instead of a macro. This change will set the bgx_id appropriately. Signed-off-by:
-
Sunil Goutham authored
When BGX/LMACs are in QSGMII mode, for some LMACs, mode info is not being printed. This patch will fix that. With changes already done to not do any sort of serdes 2 lane mapping config calculation in kernel driver, we can get rid of this logic. Signed-off-by:
-
Sunil Goutham authored
ACPI support has been added to ARM IOMMU driver in 4.10 kernel and that has resulted in VNIC interfaces throwing translation faults when kernel is booted with ACPI as driver was not using DMA API. This patch fixes the issue by using DMA API which inturn will create translation tables when IOMMU is enabled. Also VNIC doesn't have a seperate receive buffer ring per receive queue, so there is no 1:1 descriptor index matching between CQE_RX and the index in buffer ring from where a buffer has been used for DMA'ing. Unlike other NICs, here it's not possible to maintain dma address to virt address mappings within the driver. This leaves us no other choice but to use IOMMU's IOVA address conversion API to get buffer's virtual address which can be given to network stack for processing. Signed-off-by:
-
Zhu Yanjun authored
In the function rds_ib_setup_qp, the error handle is missing. When some error occurs, it is possible that memory leak occurs. As such, error handle is added. Cc: Joe Jin <joe.jin@oracle.com> Reviewed-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Guanglei Li <guanglei.li@oracle.com> Signed-off-by:
Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
-
VSR Burru authored
Improve UDP TX performance by: * reducing the ring size from 2K to 512 * replacing the numerous streaming DMA allocations for info buffers and gather lists with one large consistent DMA allocation per ring BQL is not effective here. We reduced the ring size because there is heavy overhead with dma_map_single every so often. With iommu=on, dma_map_single in PF Tx data path was taking longer time (~700usec) for every ~250 packets. Debugged intel_iommu code, and found that PF driver is utilizing too many static IO virtual address mapping entries (for gather list entries and info buffers): about 100K entries for two PF's each using 8 rings. Also, finding an empty entry (in rbtree of device domain's iova mapping in kernel) during Tx path becomes a bottleneck every so often; the loop to find the empty entry goes through over 40K iterations; this is too costly and was the major overhead. Overhead is low when this loop quits quickly. Netperf benchmark numbers before and after patch: PF UDP TX +--------+--------+------------+------------+---------+ | | | Before | After | | | Number | | Patch | Patch | | | of | Packet | Throughput | Throughput | Percent | | Flows | Size | (Gbps) | (Gbps) | Change | +--------+--------+------------+------------+---------+ | | 360 | 0.52 | 0.93 | +78.9 | | 1 | 1024 | 1.62 | 2.84 | +75.3 | | | 1518 | 2.44 | 4.21 | +72.5 | +--------+--------+------------+------------+---------+ | | 360 | 0.45 | 1.59 | +253.3 | | 4 | 1024 | 1.34 | 5.48 | +308.9 | | | 1518 | 2.27 | 8.31 | +266.1 | +--------+--------+------------+------------+---------+ | | 360 | 0.40 | 1.61 | +302.5 | | 8 | 1024 | 1.64 | 4.24 | +158.5 | | | 1518 | 2.87 | 6.52 | +127.2 | +--------+--------+------------+------------+---------+ VF UDP TX +--------+--------+------------+------------+---------+ | | | Before | After | | | Number | | Patch | Patch | | | of | Packet | Throughput | Throughput | Percent | | Flows | Size | (Gbps) | (Gbps) | Change | +--------+--------+------------+------------+---------+ | | 360 | 1.28 | 1.49 | +16.4 | | 1 | 1024 | 4.44 | 4.39 | -1.1 | | | 1518 | 6.08 | 6.51 | +7.1 | +--------+--------+------------+------------+---------+ | | 360 | 2.35 | 2.35 | 0.0 | | 4 | 1024 | 6.41 | 8.07 | +25.9 | | | 1518 | 9.56 | 9.54 | -0.2 | +--------+--------+------------+------------+---------+ | | 360 | 3.41 | 3.65 | +7.0 | | 8 | 1024 | 9.35 | 9.34 | -0.1 | | | 1518 | 9.56 | 9.57 | +0.1 | +--------+--------+------------+------------+---------+ Signed-off-by:
VSR Burru <veerasenareddy.burru@cavium.com> Signed-off-by:
Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by:
Derek Chickles <derek.chickles@cavium.com> Signed-off-by:
Raghu Vatsavayi <raghu.vatsavayi@cavium.com> Signed-off-by:
-
David Ahern authored
Dinesh reported that RTA_MULTIPATH nexthops are 8-bytes larger with IPv6 than IPv4. The recent refactoring for multipath support in netlink messages does discriminate between non-multipath which needs the OIF and multipath which adds a rtnexthop struct for each hop making the RTA_OIF attribute redundant. Resolve by adding a flag to the info function to skip the oif for multipath. Fixes: beb1afac ("net: ipv6: Add support to dump multipath routes via RTA_MULTIPATH attribute") Reported-by:
Dinesh Dutt <ddutt@cumulusnetworks.com> Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Jiri Pirko authored
This warnings may be hit even in case they should not - in case user puts a TC-flower rule which failed to be offloaded. So just remove them. Reported-by:
Petr Machata <petrm@mellanox.com> Reported-by:
Ido Schimmel <idosch@mellanox.com> Fixes: commit 7aa0f5aa ("mlxsw: spectrum: Implement TC flower offload") Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Acked-by:
-
David Ahern authored
KASAN detected a use-after-free: [ 269.467067] BUG: KASAN: use-after-free in vrf_xmit+0x7f1/0x827 [vrf] at addr ffff8800350a21c0 [ 269.467067] Read of size 4 by task ssh/1879 [ 269.467067] CPU: 1 PID: 1879 Comm: ssh Not tainted 4.10.0+ #249 [ 269.467067] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 [ 269.467067] Call Trace: [ 269.467067] dump_stack+0x81/0xb6 [ 269.467067] kasan_object_err+0x21/0x78 [ 269.467067] kasan_report+0x2f7/0x450 [ 269.467067] ? vrf_xmit+0x7f1/0x827 [vrf] [ 269.467067] ? ip_output+0xa4/0xdb [ 269.467067] __asan_load4+0x6b/0x6d [ 269.467067] vrf_xmit+0x7f1/0x827 [vrf] ... Which corresponds to the skb access after xmit handling. Fix by saving skb->len and using the saved value to update stats. Fixes: 193125db ("net: Introduce VRF device driver") Signed-off-by:
-
Jarod Wilson authored
This restores the ability to set a team device's mtu to anything higher than 1500. Similar to the reported issue with bonding, the team driver calls ether_setup(), which sets an initial max_mtu of 1500, while the underlying hardware can handle something much larger. Just set it to ETH_MAX_MTU to support all possible values, and the limitations of the underlying devices will prevent setting anything too large. Fixes: 91572088 ("net: use core MTU range checking in core net infra") CC: Cong Wang <xiyou.wangcong@gmail.com> CC: Jiri Pirko <jiri@resnulli.us> CC: netdev@vger.kernel.org Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
David S. Miller authored
Those were supposed to go into the net-next tree not the net tree. Oops... Signed-off-by: -
Christian Lamparter authored
Julian Margetson reported a panic on his SAM460EX with Kernel 4.11-rc1: | Unable to handle kernel paging request for data at address 0x00000014 | Oops: Kernel access of bad area, sig: 11 [#1] | PREEMPT | Canyonlands | Modules linked in: | CPU: 0 PID: 1 Comm: swapper Not tainted [...] | task: ea838000 task.stack: ea836000 | NIP: c0599f5c LR: c0599dd8 CTR: 00000000 | REGS: ea837c80 TRAP: 0300 Not tainted [...] | MSR: 00029000 <CE,EE,ME> | CR: 24371242 XER: 20000000 | DEAR: 00000014 ESR: 00000000 | GPR00: c0599ce8 ea837d30 ea838000 c0e52dcc c0d56ffb [...] | NIP [c0599f5c] emac_probe+0xfb4/0x1304 | LR [c0599dd8] emac_probe+0xe30/0x1304 | Call Trace: | [ea837d30] [c0599ce8] emac_probe+0xd40/0x1304 (unreliable) | [ea837d80] [c0533504] platform_drv_probe+0x48/0x90 | [ea837da0] [c0531c14] driver_probe_device+0x15c/0x2c4 | [ea837dd0] [c0531e04] __driver_attach+0x88/0xb0 | ---[ end trace ... ]--- The problem is caused by emac_dt_phy_probe() returing success (0) for existing device-trees configurations that do not specify a "phy-handle" property. This caused the code to skip the existing phy probe and setup. Which led to essential phy related data-structures being uninitialized. This patch also removes the unused variable in emac_dt_phy_connect(). Fixes: a577ca6b ("net: emac: add support for device-tree based PHY discovery and setup") Reported-by:
Julian Margetson <runaway@candw.ms> Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Signed-off-by:
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by:Geoff Levand <geoff@infradead.org> Signed-off-by:
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by: -
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by:
-
