It turns out that libvirt uses 0-vid as a default if no vlan was
set for the guest (which is the case for switchdev mode) and errs
if we disallow that:

error: Failed to start domain vm75
error: Cannot set interface MAC/vlanid to 6a:66:2d:48:92:c2/0 \
		for ifname enp59s0f0 vf 0: Operation not supported

So allow this in order not to break existing systems.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With VF LAG commit 491c37e4 "net/mlx5e: In case of LAG, one switch
parent id is used for all representors", both uplinks and all the VFs
(on both of them) get the same switchdev id.

This cause the provisioning system method to identify the rep of a given
VF from the parent PF PCI device using switchev id and physical port
name to break, since VFm of PF0 will have the (id, name) as VFm of PF1.

To fix that, we align to use the framework agreed upstream and set by
nfp commit 168c478e "nfp: wire get_phys_port_name on representors":

$ cat /sys/class/net/eth4_*/phys_port_name
p0
pf0vf0
pf0vf1

Now, the names will be different, e.g. pf0vf0 vs. pf1vf0.

Fixes: 491c37e4 ("net/mlx5e: In case of LAG, one switch parent id is used for all representors")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Waleed Musa <waleedm@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Prior to this patch the driver prohibited spoof checking on invalid MAC.
Now the user can set this configuration if it wishes to.

This is required since libvirt might invalidate the VF Mac by setting it
to zero, while spoofcheck is ON.

Fixes: 1ab2068a ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The lock in qp_table might be taken from process context or from
interrupt context. This may lead to a deadlock unless it is taken with
IRQs disabled.

Discovered by lockdep

================================
WARNING: inconsistent lock state
4.20.0-rc6
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W}

python/12572 [HC1[1]:SC0[0]:HE0:SE1] takes:
00000000052a4df4 (&(&table->lock)->rlock#2){?.+.}, /0x50 [mlx5_core]
{HARDIRQ-ON-W} state was registered at:
  _raw_spin_lock+0x33/0x70
  mlx5_get_rsc+0x1a/0x50 [mlx5_core]
  mlx5_ib_eqe_pf_action+0x493/0x1be0 [mlx5_ib]
  process_one_work+0x90c/0x1820
  worker_thread+0x87/0xbb0
  kthread+0x320/0x3e0
  ret_from_fork+0x24/0x30
irq event stamp: 103928
hardirqs last  enabled at (103927): [] nk+0x1a/0x1c
hardirqs last disabled at (103928): [] unk+0x1a/0x1c
softirqs last  enabled at (103924): [] tcp_sendmsg+0x31/0x40
softirqs last disabled at (103922): [] 80

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&table->lock)->rlock#2);

    lock(&(&table->lock)->rlock#2);

 *** DEADLOCK ***

Fixes: 032080ab ("IB/mlx5: Lock QP during page fault handling")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

MLX5E_PFLAG_* definitions were changed from bitmask to enumerated
values. However, in mlx5e_open_rq(), the proper API (MLX5E_GET_PFLAG macro)
was not used to read the flag value of MLX5E_PFLAG_RX_NO_CSUM_COMPLETE.
Fixed it.

Fixes: 8ff57c18 ("net/mlx5e: Improve ethtool private-flags code structure")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

This reverts commit 5f5991f3.

With the original commit, eswitch instance will not be initialized for
a function which is vport group manager but not eswitch manager such as
host PF on SmartNIC (BlueField) card. This will result in a kernel crash
when such a vport group manager is trying to access vports in its group.
E.g, PF vport manager (not eswitch manager) tries to configure the MAC
of its VF vport, a kernel trace will happen similar as bellow:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
 ...
 RIP: 0010:mlx5_eswitch_get_vport_config+0xc/0x180 [mlx5_core]
 ...

Fixes: 5f5991f3 ("net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Pull pstore fixes from Kees Cook:

 - Fix console ramoops to show the previous boot logs (Sai Prakash
   Ranjan)

 - Avoid allocation and leak of platform data

* tag 'pstore-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore/ram: Avoid allocation and leak of platform data
  pstore/ram: Fix console ramoops to show the previous boot logs

Pull gcc-plugins fixes from Kees Cook:
 "Fix ARM per-task stack protector plugin under GCC 9 (Ard Biesheuvel)"

* tag 'gcc-plugins-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: arm_ssp_per_task_plugin: fix for GCC 9+
  gcc-plugins: arm_ssp_per_task_plugin: sign extend the SP mask

Pull networking fixes from David Miller:

 1) Fix endless loop in nf_tables, from Phil Sutter.

 2) Fix cross namespace ip6_gre tunnel hash list corruption, from
    Olivier Matz.

 3) Don't be too strict in phy_start_aneg() otherwise we might not allow
    restarting auto negotiation. From Heiner Kallweit.

 4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.

 5) Memory leak in act_tunnel_key, from Davide Caratti.

 6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.

 7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.

 8) Missing udplite rehash callbacks, from Alexey Kodanev.

 9) Log dirty pages properly in vhost, from Jason Wang.

10) Use consume_skb() in neigh_probe() as this is a normal free not a
    drop, from Yang Wei. Likewise in macvlan_process_broadcast().

11) Missing device_del() in mdiobus_register() error paths, from Thomas
    Petazzoni.

12) Fix checksum handling of short packets in mlx5, from Cong Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
  bpf: in __bpf_redirect_no_mac pull mac only if present
  virtio_net: bulk free tx skbs
  net: phy: phy driver features are mandatory
  isdn: avm: Fix string plus integer warning from Clang
  net/mlx5e: Fix cb_ident duplicate in indirect block register
  net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
  net/mlx5e: Fix wrong error code return on FEC query failure
  net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
  tools: bpftool: Cleanup license mess
  bpf: fix inner map masking to prevent oob under speculation
  bpf: pull in pkt_sched.h header for tooling to fix bpftool build
  selftests: forwarding: Add a test case for externally learned FDB entries
  selftests: mlxsw: Test FDB offload indication
  mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
  net: bridge: Mark FDB entries that were added by user as such
  mlxsw: spectrum_fid: Update dummy FID index
  mlxsw: pci: Return error on PCI reset timeout
  mlxsw: pci: Increase PCI SW reset timeout
  mlxsw: pci: Ring CQ's doorbell before RDQ's
  MAINTAINERS: update email addresses of liquidio driver maintainers
  ...

Yue Hu noticed that when parsing device tree the allocated platform data
was never freed. Since it's not used beyond the function scope, this
switches to using a stack variable instead.
Reported-by: Yue Hu <huyue2@yulong.com>
Fixes: 35da6094 ("pstore/ram: add Device Tree bindings")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>

GCC 9 reworks the way the references to the stack canary are
emitted, to prevent the value from being spilled to the stack
before the final comparison in the epilogue, defeating the
purpose, given that the spill slot is under control of the
attacker that we are protecting ourselves from.

Since our canary value address is obtained without accessing
memory (as opposed to pre-v7 code that will obtain it from a
literal pool), it is unlikely (although not guaranteed) that
the compiler will spill the canary value in the same way, so
let's just disable this improvement when building with GCC9+.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

The ARM per-task stack protector GCC plugin hits an assert in
the compiler in some case, due to the fact the the SP mask
expression is not sign-extended as it should be. So fix that.
Suggested-by: Kugan Vivekanandarajah <kugan.vivekanandarajah@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
 "Fixes and cleanups all over the place"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost/scsi: Use copy_to_iter() to send control queue response
  vhost: return EINVAL if iovecs size does not match the message size
  virtio-balloon: tweak config_changed implementation
  virtio: don't allocate vqs when names[i] = NULL
  virtio_pci: use queue idx instead of array idx to set up the vq
  virtio: document virtio_config_ops restrictions
  virtio: fix virtio_config_ops description

Pull btrfs fixes from David Sterba:
 "A handful of fixes (some of them in testing for a long time):

   - fix some test failures regarding cleanup after transaction abort

   - revert of a patch that could cause a deadlock

   - delayed iput fixes, that can help in ENOSPC situation when there's
     low space and a lot data to write"

* tag 'for-5.0-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: wakeup cleaner thread when adding delayed iput
  btrfs: run delayed iputs before committing
  btrfs: wait on ordered extents on abort cleanup
  btrfs: handle delayed ref head accounting cleanup in abort
  Revert "btrfs: balance dirty metadata pages in btrfs_finish_ordered_io"

Merge tags 'compiler-attributes-for-linus-v5.0-rc3' and 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux

Pull misc clang fixes from Miguel Ojeda:

  - A fix for OPTIMIZER_HIDE_VAR from Michael S Tsirkin

  - Update clang-format with the latest for_each macro list from Jason
    Gunthorpe

* tag 'compiler-attributes-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
  include/linux/compiler*.h: fix OPTIMIZER_HIDE_VAR

* tag 'clang-format-for-linus-v5.0-rc3' of git://github.com/ojeda/linux:
  clang-format: Update .clang-format with the latest for_each macro list

If an input number x for int_sqrt64() has the highest bit set, then
fls64(x) is 64.  (1UL << 64) is an overflow and breaks the algorithm.

Subtracting 1 is a better guess for the initial value of m anyway and
that's what also done in int_sqrt() implicitly [*].

[*] Note how int_sqrt() uses __fls() with two underscores, which already
    returns the proper raw bit number.

    In contrast, int_sqrt64() used fls64(), and that returns bit numbers
    illogically starting at 1, because of error handling for the "no
    bits set" case. Will points out that he bug probably is due to a
    copy-and-paste error from the regular int_sqrt() case.
Signed-off-by: Florian La Roche <Florian.LaRoche@googlemail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 594cc251 ("make 'user_access_begin()' do 'access_ok()'")
makes the access_ok() check part of the user_access_begin() preceding a
series of 'unsafe' accesses.  This has the desirable effect of ensuring
that all 'unsafe' accesses have been range-checked, without having to
pick through all of the callsites to verify whether the appropriate
checking has been made.

However, the consolidated range check does not inhibit speculation, so
it is still up to the caller to ensure that they are not susceptible to
any speculative side-channel attacks for user addresses that ultimately
fail the access_ok() check.

This is an oversight, so use __uaccess_begin_nospec() to ensure that
speculation is inhibited until the access_ok() check has passed.
Reported-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull arm64 fixes from Will Deacon:
 "Three arm64 fixes for -rc3.

  We've plugged a couple of nasty issues involving KASLR-enabled
  kernels, and removed a redundant #define that was introduced as part
  of the KHWASAN fixes from akpm at -rc2.

   - Fix broken kpti page-table rewrite in bizarre KASLR configuration

   - Fix module loading with KASLR

   - Remove redundant definition of ARCH_SLAB_MINALIGN"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kasan, arm64: remove redundant ARCH_SLAB_MINALIGN define
  arm64: kaslr: ensure randomized quantities are clean to the PoC
  arm64: kpti: Update arm64_kernel_use_ng_mappings() when forced on

Daniel Borkmann says:

====================
pull-request: bpf 2019-01-20

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a out-of-bounds access in __bpf_redirect_no_mac, from Willem.

2) Fix bpf_setsockopt to reset sock dst on SO_MARK changes, from Peter.

3) Fix map in map masking to prevent out-of-bounds access under
   speculative execution, from Daniel.

4) Fix bpf_setsockopt's SO_MAX_PACING_RATE to support TCP internal
   pacing, from Yuchung.

5) Fix json writer license in bpftool, from Thomas.

6) Fix AF_XDP to check if an actually queue exists during umem
   setup, from Krzysztof.

7) Several fixes to BPF stackmap's build id handling. Another fix
   for bpftool build to account for libbfd variations wrt linking
   requirements, from Stanislav.

8) Fix BPF samples build with clang by working around missing asm
   goto, from Yonghong.

9) Fix libbpf to retry program load on signal interrupt, from Lorenz.

10) Various minor compile warning fixes in BPF code, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller was able to construct a packet of negative length by
redirecting from bpf_prog_test_run_skb with BPF_PROG_TYPE_LWT_XMIT:

    BUG: KASAN: slab-out-of-bounds in memcpy include/linux/string.h:345 [inline]
    BUG: KASAN: slab-out-of-bounds in skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    BUG: KASAN: slab-out-of-bounds in __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    Read of size 4294967282 at addr ffff8801d798009c by task syz-executor2/12942

    kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
    check_memory_region_inline mm/kasan/kasan.c:260 [inline]
    check_memory_region+0x13e/0x1b0 mm/kasan/kasan.c:267
    memcpy+0x23/0x50 mm/kasan/kasan.c:302
    memcpy include/linux/string.h:345 [inline]
    skb_copy_from_linear_data include/linux/skbuff.h:3421 [inline]
    __pskb_copy_fclone+0x2dd/0xeb0 net/core/skbuff.c:1395
    __pskb_copy include/linux/skbuff.h:1053 [inline]
    pskb_copy include/linux/skbuff.h:2904 [inline]
    skb_realloc_headroom+0xe7/0x120 net/core/skbuff.c:1539
    ipip6_tunnel_xmit net/ipv6/sit.c:965 [inline]
    sit_tunnel_xmit+0xe1b/0x30d0 net/ipv6/sit.c:1029
    __netdev_start_xmit include/linux/netdevice.h:4325 [inline]
    netdev_start_xmit include/linux/netdevice.h:4334 [inline]
    xmit_one net/core/dev.c:3219 [inline]
    dev_hard_start_xmit+0x295/0xc90 net/core/dev.c:3235
    __dev_queue_xmit+0x2f0d/0x3950 net/core/dev.c:3805
    dev_queue_xmit+0x17/0x20 net/core/dev.c:3838
    __bpf_tx_skb net/core/filter.c:2016 [inline]
    __bpf_redirect_common net/core/filter.c:2054 [inline]
    __bpf_redirect+0x5cf/0xb20 net/core/filter.c:2061
    ____bpf_clone_redirect net/core/filter.c:2094 [inline]
    bpf_clone_redirect+0x2f6/0x490 net/core/filter.c:2066
    bpf_prog_41f2bcae09cd4ac3+0xb25/0x1000

The generated test constructs a packet with mac header, network
header, skb->data pointing to network header and skb->len 0.

Redirecting to a sit0 through __bpf_redirect_no_mac pulls the
mac length, even though skb->data already is at skb->network_header.
bpf_prog_test_run_skb has already pulled it as LWT_XMIT !is_l2.

Update the offset calculation to pull only if skb->data differs
from skb->network_header, which is not true in this case.

The test itself can be run only from commit 1cf1cae9 ("bpf:
introduce BPF_PROG_TEST_RUN command"), but the same type of packets
with skb at network header could already be built from lwt xmit hooks,
so this fix is more relevant to that commit.

Also set the mac header on redirect from LWT_XMIT, as even after this
change to __bpf_redirect_no_mac that field is expected to be set, but
is not yet in ip_finish_output2.

Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Use napi_consume_skb() to get bulk free.  Note that napi_consume_skb is
safe to call in a non-napi context as long as the napi_budget flag is
correct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS fixes from Paul Burton:

 - Fix IPI handling for Lantiq SoCs, which was broken by changes made
   back in v4.12.

 - Enable OF/DT serial support in ath79_defconfig to give us working
   serial by default.

 - Fix 64b builds for the Jazz platform.

 - Set up a struct device for the BCM47xx SoC to allow BCM47xx drivers
   to perform DMA again following the major DMA mapping changes made in
   v4.19.

 - Disable MSI on Cavium Octeon systems when the pcie_disable command
   line parameter introduced in v3.3 is used, in order to avoid
   inadvetently accessing PCIe controller registers despite the command
   line.

 - Fix a build failure for Cavium Octeon kernels with kexec enabled,
   introduced in v4.20.

 - Fix a regression in the behaviour of semctl/shmctl/msgctl IPC
   syscalls for kernels including n32 support but not o32 support caused
   by some cleanup in v3.19.

* tag 'mips_fixes_5.0_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: OCTEON: fix kexec support
  mips: fix n32 compat_ipc_parse_version
  Disable MSI also when pcie-octeon.pcie_disable on
  MIPS: BCM47XX: Setup struct device for the SoC
  MIPS: jazz: fix 64bit build
  MIPS: ath79: Enable OF serial ports in the default config
  MIPS: lantiq: Use CP0_LEGACY_COMPARE_IRQ
  MIPS: lantiq: Fix IPI interrupt handling

Pull Devicetree fix from Rob Herring:
 "A single build fix for powerpc due to device_node.type removal"

* tag 'devicetree-fixes-for-5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  powerpc: chrp: Use of_node_is_type to access device_type

Pull libnvdimm fixes from Dan Williams:
 "A crash fix, a build warning fix, a miscellaneous small cleanups.

  In case anyone is looking for them, there was a regression caught by
  testing that caused two patches to be dropped from this update.  Those
  patches have been reworked and will soak for another week / re-target
  5.0-rc4.

   - Fix driver initialization crash due to the inability to report an
     'error' state for a DIMM's security capability.

   - Build warning fix for little-endian ARM64 builds

   - Fix a potential race between the EDAC driver's usage of the NFIT
     SMBIOS id for a DIMM and the driver shutdown path.

   - A small collection of one-line benign cleanups for duplicate
     variable assignments, a duplicate header include and a mis-typed
     function argument"

* tag 'libnvdimm-fixes-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm/security: Fix nvdimm_security_state() state request selection
  acpi/nfit: Remove duplicate set nd_set in acpi_nfit_init_interleave_set()
  acpi/nfit: Fix race accessing memdev in nfit_get_smbios_id()
  libnvdimm/dimm: Fix security capability detection for non-Intel NVDIMMs
  nfit: Mark some functions as __maybe_unused
  ACPI/nfit: delete the function to_acpi_nfit_desc
  ACPI/nfit: delete the redundant header file

Pull watchdog fixes from Wim Van Sebroeck:

 - mt7621_wdt/rt2880_wdt: Fix compilation problem

 - tqmx86: Fix a couple IS_ERR() vs NULL bugs

* tag 'linux-watchdog-5.0-rc-fixes' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: tqmx86: Fix a couple IS_ERR() vs NULL bugs
  watchdog: mt7621_wdt/rt2880_wdt: Fix compilation problem

Pull NFS client fixes from Anna Schumaker:
 "These are mostly fixes for SUNRPC bugs, with a single v4.2
  copy_file_range() fix mixed in.

  Stable bugfixes:
   - Fix TCP receive code on archs with flush_dcache_page()

  Other bugfixes:
   - Fix error code in rpcrdma_buffer_create()
   - Fix a double free in rpcrdma_send_ctxs_create()
   - Fix kernel BUG at kernel/cred.c:825
   - Fix unnecessary retry in nfs42_proc_copy_file_range()
   - Ensure rq_bytes_sent is reset before request transmission
   - Ensure we respect the RPCSEC_GSS sequence number limit
   - Address Kerberos performance/behavior regression"

* tag 'nfs-for-5.0-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC: Address Kerberos performance/behavior regression
  SUNRPC: Ensure we respect the RPCSEC_GSS sequence number limit
  SUNRPC: Ensure rq_bytes_sent is reset before request transmission
  NFSv4.2 fix unnecessary retry in nfs4_copy_file_range
  sunrpc: kernel BUG at kernel/cred.c:825!
  SUNRPC: Fix TCP receive code on archs with flush_dcache_page()
  xprtrdma: Double free in rpcrdma_sendctxs_create()
  xprtrdma: Fix error code in rpcrdma_buffer_create()

Pull SCSI fixes from James Bottomley:
 "A set of 17 fixes. Most of these are minor or trivial.

  The one fix that may be serious is the isci one: the bug can cause hba
  parameters to be set from uninitialized memory. I don't think it's
  exploitable, but you never know"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: cxgb4i: add wait_for_completion()
  scsi: qla1280: set 64bit coherent mask
  scsi: ufs: Fix geometry descriptor size
  scsi: megaraid_sas: Retry reads of outbound_intr_status reg
  scsi: qedi: Add ep_state for login completion on un-reachable targets
  scsi: ufs: Fix system suspend status
  scsi: qla2xxx: Use correct number of vectors for online CPUs
  scsi: hisi_sas: Set protection parameters prior to adding SCSI host
  scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
  scsi: isci: initialize shost fully before calling scsi_add_host()
  scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
  scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
  scsi: core: Synchronize request queue PM status only on successful resume
  scsi: pm80xx: reduce indentation
  scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
  scsi: megaraid_sas: correct an info message
  scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
  scsi: sd: Fix cache_type_store()

Pull block fixes from Jens Axboe:

 - block size setting fixes for loop/nbd (Jan Kara)

 - md bio_alloc_mddev() cleanup (Marcos)

 - Ensure we don't lose the REQ_INTEGRITY flag (Ming)

 - Two NVMe fixes by way of Christoph:
    - Fix NVMe IRQ calculation (Ming)
    - Uninitialized variable in nvmet-tcp (Sagi)

 - BFQ comment fix (Paolo)

 - License cleanup for recently added blk-mq-debugfs-zoned (Thomas)

* tag 'for-linus-20190118' of git://git.kernel.dk/linux-block:
  block: Cleanup license notice
  nvme-pci: fix nvme_setup_irqs()
  nvmet-tcp: fix uninitialized variable access
  block: don't lose track of REQ_INTEGRITY flag
  blockdev: Fix livelocks on loop device
  nbd: Use set_blocksize() to set device blocksize
  md: Make bio_alloc_mddev use bio_alloc_bioset
  block, bfq: fix comments on __bfq_deactivate_entity

Re-run the shell fragment that generated the original list. In particular
this adds the missing xarray related functions.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>

Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.

Prevent the phy driver from registering if the features field is missing.

Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit in Clang expanded the -Wstring-plus-int warning, showing
some odd behavior in this file.

drivers/isdn/hardware/avm/b1.c:426:30: warning: adding 'int' to a string does not append to the string [-Wstring-plus-int]
                cinfo->version[j] = "\0\0" + 1;
                                    ~~~~~~~^~~
drivers/isdn/hardware/avm/b1.c:426:30: note: use array indexing to silence this warning
                cinfo->version[j] = "\0\0" + 1;
                                           ^
                                    &      [  ]
1 warning generated.

This is equivalent to just "\0". Nick pointed out that it is smarter to
use "" instead of "\0" because "" is used elsewhere in the kernel and
can be deduplicated at the linking stage.

Link: https://github.com/ClangBuiltLinux/linux/issues/309Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 8ce5f841 ("of: Remove struct device_node.type pointer")
removed struct device_node.type pointer, but the conversion to use
of_node_is_type() accessor was missed in chrp_init_IRQ().

Fixes: 8ce5f841 ("of: Remove struct device_node.type pointer")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-01-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')

The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.

Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.

Fixes: f5bc2c5d ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Advertised and configured FEC query failure resulted in printing
wrong error code.

Fixes: 6cfa9460 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.

Prior to:
commit '88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.

Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Precise and non-ambiguous license information is important. The recent
relicensing of the bpftools introduced a license conflict.

The files have now:

     SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause

and

     * This program is free software; you can redistribute it and/or
     * modify it under the terms of the GNU General Public License
     * as published by the Free Software Foundation; either version
     * 2 of the License, or (at your option) any later version

Amazingly about 20 people acked that change and neither they nor the
committer noticed. Oh well.

Digging deeper: The files were imported from the iproute2 repository with
the GPL V2 or later boiler plate text in commit b66e907c ("tools:
bpftool: copy JSON writer from iproute2 repository")

Looking at the iproute2 repository at

  git://git.kernel.org/pub/scm/network/iproute2/iproute2.git

the following commit is the equivivalent:

  commit d9d8c839 ("json_writer: add SPDX Identifier (GPL-2/BSD-2)")

That commit explicitly removes the boiler plate and relicenses the code
uner GPL-2.0-only and BSD-2-Clause. As Steven wrote the original code and
also the relicensing commit, it's assumed that the relicensing was intended
to do exaclty that. Just the kernel side update failed to remove the boiler
plate. Do so now.

Fixes: 907b2236 ("tools: bpftool: dual license all files")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Sean Young <sean@mess.org>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: David Calavera <david.calavera@gmail.com>
Cc: Andrey Ignatov <rdna@fb.com>
Cc: Joe Stringer <joe@wand.net.nz>
Cc: David Ahern <dsahern@gmail.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Petar Penkov <ppenkov@stanford.edu>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Taeung Song <treeze.taeung@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
CC: okash.khawaja@gmail.com
Cc: netdev@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

During review I noticed that inner meta map setup for map in
map is buggy in that it does not propagate all needed data
from the reference map which the verifier is later accessing.

In particular one such case is index masking to prevent out of
bounds access under speculative execution due to missing the
map's unpriv_array/index_mask field propagation. Fix this such
that the verifier is generating the correct code for inlined
lookups in case of unpriviledged use.

Before patch (test_verifier's 'map in map access' dump):

  # bpftool prog dump xla id 3
     0: (62) *(u32 *)(r10 -4) = 0
     1: (bf) r2 = r10
     2: (07) r2 += -4
     3: (18) r1 = map[id:4]
     5: (07) r1 += 272                |
     6: (61) r0 = *(u32 *)(r2 +0)     |
     7: (35) if r0 >= 0x1 goto pc+6   | Inlined map in map lookup
     8: (54) (u32) r0 &= (u32) 0      | with index masking for
     9: (67) r0 <<= 3                 | map->unpriv_array.
    10: (0f) r0 += r1                 |
    11: (79) r0 = *(u64 *)(r0 +0)     |
    12: (15) if r0 == 0x0 goto pc+1   |
    13: (05) goto pc+1                |
    14: (b7) r0 = 0                   |
    15: (15) if r0 == 0x0 goto pc+11
    16: (62) *(u32 *)(r10 -4) = 0
    17: (bf) r2 = r10
    18: (07) r2 += -4
    19: (bf) r1 = r0
    20: (07) r1 += 272                |
    21: (61) r0 = *(u32 *)(r2 +0)     | Index masking missing (!)
    22: (35) if r0 >= 0x1 goto pc+3   | for inner map despite
    23: (67) r0 <<= 3                 | map->unpriv_array set.
    24: (0f) r0 += r1                 |
    25: (05) goto pc+1                |
    26: (b7) r0 = 0                   |
    27: (b7) r0 = 0
    28: (95) exit

After patch:

  # bpftool prog dump xla id 1
     0: (62) *(u32 *)(r10 -4) = 0
     1: (bf) r2 = r10
     2: (07) r2 += -4
     3: (18) r1 = map[id:2]
     5: (07) r1 += 272                |
     6: (61) r0 = *(u32 *)(r2 +0)     |
     7: (35) if r0 >= 0x1 goto pc+6   | Same inlined map in map lookup
     8: (54) (u32) r0 &= (u32) 0      | with index masking due to
     9: (67) r0 <<= 3                 | map->unpriv_array.
    10: (0f) r0 += r1                 |
    11: (79) r0 = *(u64 *)(r0 +0)     |
    12: (15) if r0 == 0x0 goto pc+1   |
    13: (05) goto pc+1                |
    14: (b7) r0 = 0                   |
    15: (15) if r0 == 0x0 goto pc+12
    16: (62) *(u32 *)(r10 -4) = 0
    17: (bf) r2 = r10
    18: (07) r2 += -4
    19: (bf) r1 = r0
    20: (07) r1 += 272                |
    21: (61) r0 = *(u32 *)(r2 +0)     |
    22: (35) if r0 >= 0x1 goto pc+4   | Now fixed inlined inner map
    23: (54) (u32) r0 &= (u32) 0      | lookup with proper index masking
    24: (67) r0 <<= 3                 | for map->unpriv_array.
    25: (0f) r0 += r1                 |
    26: (05) goto pc+1                |
    27: (b7) r0 = 0                   |
    28: (b7) r0 = 0
    29: (95) exit

Fixes: b2157399 ("bpf: prevent out-of-bounds speculation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>