The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
 - Disable the I2C.
 - Write to SOFTRESET bit.
 - Enable the I2C.
 - Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer.  omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
 HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
 offset conditional code to use the IP block revision; minor code
 cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on.  We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

These represent the 8 kinds of implementation functionality
that up until now were inferred by the 16 remaining cpu_...()
tests in the omap i2c driver.

Changed to use BIT() as suggested by Balaji T Krishnamoorthy.

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

These represent the two kinds of (incompatible) OMAP I2C
peripheral unit in use so far.

The constants are in linux/i2c-omap.h so the omap i2c driver can have
them too.

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

As part of removing cpu_...() from the OMAP I2C driver, we need to
convert the CPU tests into functionality flags that are set by
hwmod class in the same way the IP revision is.

More flags are needed than will fit in the existing u8 flags
member of omap_i2c_dev_attr.

These flags can refer to options inside the IP block but they are
most needed for information about cpu implementation specific
options that are not part of the IP block itself.  For example,
how the CPU data bus is wired to the IP block databus differs
between OMAP cpus and affects how you must shift the address in
the IP block, but is not a feature of the IP block itself.

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Peter Maydell noticed when running under QEMU he was getting
errors reporting 32-bit access to I2C peripheral unit registers
that are documented to be 8 or 16-bit only[1][2]

The I2C driver is blameless as it wraps its accesses in a
function using __raw_writew and __raw_readw, it turned out it
is the hwmod stuff.

However the hwmod code already has a flag to force a
perhipheral unit to only be accessed using 16-bit operations.

This patch applies the 16-bit only flag to the 2430,
OMAP3xxx and OMAP44xx hwmod structs.  2420 was already
correctly marked up as 16-bit.

The 2430 change will need testing by TI as arranged
in the comments to the previous patch version.

When the 16-bit flag is or-ed with other flags, it is placed
first as requested in comments.

[1] OMAP4430 Technical reference manual section 23.1.6.2
[2] OMAP3530 Techincal reference manual section 18.6

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Currently using pm_runtime with DSS requires the DSS driver to enable
the DSS functional clock before calling pm_runtime_get(). That makes it
impossible to use pm_runtime in DSS as it is meant to be used, with
pm_runtime callbacks.

This patch changes the hwmod database for OMAP4 so that enabling the
hwmod via pm_runtime will also enable the DSS functional clock, allowing
us to use pm_runtime properly in DSS driver.

The DSS HWMOD side is not really correct, not before nor after this
patch, and getting DSS to retention will probably not work currently.
However, it is not supported in the mainline kernel anyway, so this
won't break anything.

So this patch allows us to write the pm_runtime adaptation for the DSS
driver the way it should be done, and the HWMOD/PM side can be fixed
later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Add missing DSS optional clocks to HWMOD data for OMAP4xxx.

Add HWMOD_CONTROL_OPT_CLKS_IN_RESET flag for dispc to fix dispc reset.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[b-cousson@ti.com: Remove a comment and update the subject]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: removed DSS "fck" role and some clkdev aliases at Tomi's
 request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Merge branches 'dmtimer_precleanup_3.1', 'hwmod_core_cleanup_a_3.1', 'combine_common_hwmod_3.1', 'omap4_hwmod_data_cleanup_a_3.1', 'clock_cleanup_a_3.1', 'prcm_cleanup_a_3.1', 'omap_pm_cleanup_3.1' and 'omap_device_cleanup_3.1' into prcm-cleanup-3.1

UNIPRO was removed from OMAP4 devices from ES2.0 onwards.
Since this IP was anyway non-functional and not supported,
it is best to remove it completely.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[b-cousson@ti.com: Update the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split PRCM header file changes into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

McASP2, 3 and MMC6 modules are not present in the OMAP4 family.
Remove the fclk and the clksel related to these nodes.
Rename the references that were potentially re-used in order nodes.

Remove related macros in prcm header files.

Update TI copyright date.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[b-cousson@ti.com: Update the patch according to autogen output]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: split PRCM data changes into a separate patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The current code base is not linking with the OMAP_PM_NONE
option set.
Since the option OMAP_PM_NOOP provides a no-op/debug layer,
OMAP_PM_NONE can be removed.
OMAP_PM_NOOP is enabled by default by Kconfig.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The omap_device layer currently has two ways of getting an omap_device
pointer from a platform_device pointer.

Replace current usage of _find_by_pdev() with to_omap_device() since
to_omap_device() is more familiar to the existing to_platform_device()
used when getting a platform_device pointer from a struct device pointer.

Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

MPUSS was renamed MPU and L3_D2D D2D.
The rename will slightly change the order of the structure
and thus generate some structures moves.

Add a comment and remove a comma.

Update Copyright for TI and Nokia and add back Paul
in the author list.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Some maros were not well aligned. Re-align them.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The restore part of the CM is an alias of some regular registers
used only during the SAR restore to facilate the dma to write
a contiguous set of registers.
The registers should never be used by the SW, only the original
register have to be used.

Remove them from cmX_44xx.h files to avoid anybody to use them by
mistake.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Indent flags to be aligned with other fields.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
[paul@pwsan.com: split this patch from an earlier patch by Benoît;
 edited commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The following commit introduced new macros to define an offset
per clock domain in an instance.

commit e4156ee5

    OMAP4: CM instances: add clockdomain register offsets

The PRM contains only two clock controls management entities:
EMU and WKUP.
Remove the other ones.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

A couple of macros were wrongly changed during the _MOD to _INST
rename done in the following commit:

  OMAP4: PRCM: rename _MOD macros to _INST
  cdb54c44

Fix them to their original name.

Some CM and PRM instances were not well aligned. Align them.

Remove one blank line in cm2_44xx.h to align the output with
the other (cm1_44xx.h, prm44xx.h) files.

Update header copyright date.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The DPLL USB can generate higher speed (x2) than the regular ones.
The max multiplication value is then twice the previous value.

Fix both max_mult and max_div with that correct values.

Change the max_div variable type to u16 to allow storing up to 256.

Replace as well the define with the value to avoid
unneeded indirection and provide a better readability.

Remove the defines that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

A couple of fieds were edited manually and thus do not stick
to the template used by the generator and by other structures.

Move them to the correct location.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped the UNIPRO changes since those will be removed
 in a later patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

usb_host_fs_fck does have a clkdev mapping with "usbhs-omap.0"
and "fs_fck" alias used by the driver.
The entry with NULL dev is thus not needed anymore.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The USB DPLL is a J-Type DPLL with the sddiv extra parameter.  Add it
in USB DPLL.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: dropped UNIPRO change since it is removed in a later patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The interconnect modules were using a slightly different layout than
the regular modules.
Align the layout for better consitency.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Fix .prcm alignement and usb_otg_hs class and hwmod structures.

Add a couple of more potential hwmods in the comment.
Remove hsi, since it is already included in the data.

Remove one blank line.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

A couple of parens were added around some flags.

Remove them, since they are not needed and not used
for any other hwmods.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Change the position of the ocp_if structure to match the template.

Remove unneeded comma at the end of address space flag field.

Remove USER_SDMA since this ocp link is only from the l3_main_1
path that is accessible only from the MPU in that case and not
the SDMA.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_class and omap_hwmod_class_sysconfig arrays across OMAP2xxx
and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_dma_info arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_mpu_irqs arrays across OMAP2xxx and 3xxx hwmod data files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

To reduce kernel source file data duplication, share struct
omap_hwmod_addr_space arrays across OMAP2xxx and 3xxx hwmod data
files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Move the pr_debug at the top of the function
to trace the entry even if the first test is failing.
That help understanding that we entered the function
but failed in it.

Move the _enable last part out of the test to reduce
indentation and improve readability.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

Change the debug into warning to check what IPs are failing.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The HW reset must be de-assert after the clocks are enabled
but before waiting for the target to be ready. Otherwise the
reset might not work properly since the clock is not running
to proceed the reset.

De-assert the reset after _enable_clocks and before
_wait_target_ready.
Re-assert it only when the clocks are disabled.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

It is perfectly valid for some hwmod to not have any
register target address for sysconfig. This is especially
true for interconnect hwmods.
Remove the warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

The Type 2 type of IPs will not have any enawakeup bit in their sysconfig.
Writing to that bit will instead trigger a softreset.
Check the flag to write this bit only if the module supports it.
Reported-by: Miguel Vadillo <vadillo@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>