Node names are supposed to be generic, fix the RTC and codec node
names for both Hummingboard and Cubox-i.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the SD card regulator, which allows the SD card power to be switched
on/off.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rev 1.5 microsoms include eMMC support on-board.  Add a microsom include
file which can be used to add support for this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the TI Wi-Fi WL1837 device on SolidRun's revision
1.5 microsoms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a 3.3V regulator for devices connected to the vcc_3v3 supply
signal on the microsom.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDIO clock is really the Broadcom clock.  Rename it as such.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi.  The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use real iomuxc values rather than preserving the boot loader value for
the SOMs ethernet.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the microsom includes into the .dts files so different options can
be accomodated at the lowest level.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom.  Change the name to the shorter "imx6qdl-sr-som".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file.  Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The regulators node is redundant, and serves no useful function.
Remove it from i.MX6 SolidRun platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.

This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).

Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).

To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As explained in Documentation/devicetree/bindings/net/fsl-fec.txt the
phy-reset-gpios is active high only if the 'phy-reset-active-high' is
present.

As 'phy-reset-active-high' is not used here, fix the device tree
description by passing GPIO_ACTIVE_LOW flag.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On imx6qdl-sabreauto the HDMI DDC bus is connected to I2C2, so
pass the 'ddc-i2c-bus' property accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for PCIe support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently the imx pci driver fails to probe on i.MX6SX.

Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.

Tested on a im6sx-sdb board:

00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.

This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit a22950c8 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in i.MX dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.

Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.

On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7s/imx7d has the ptp interrupt newly added as well.

For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2

For imx6sx, "int0" handles all 3 queues and ENET_MII

And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is needed for the bootloader to patch in the correct MAC address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warning is seen with W=1:

Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property

Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:

Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Tested-by: Lothar Waßmann <LW@karo-electronics.de>
Acked-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HPFS does not set SB_I_VERSION and does not use the i_version counter
internally.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Mikulas Patocka <mikulas@twibright.com>
Reviewed-by: Mikulas Patocka <mikulas@twibright.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sign_extend32 counts the sign bit parameter from 0, not from 1.  So we
have to use "11" for 12th bit, not "12".

This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a4 ("futex: Remove duplicated code and fix undefined
behaviour") till now.

Fixes: 30d6e0a4 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs fixes from David Sterba:
 "This contains a few fixes (error handling, quota leak, FUA vs
  nobarrier mount option).

  There's one one worth mentioning separately - an off-by-one fix that
  leads to overwriting first byte of an adjacent page with 0, out of
  bounds of the memory allocated by an ioctl. This is under a privileged
  part of the ioctl, can be triggerd in some subvolume layouts"

* tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Fix possible off-by-one in btrfs_search_path_in_tree
  Btrfs: disable FUA if mounted with nobarrier
  btrfs: fix missing error return in btrfs_drop_snapshot
  btrfs: handle errors while updating refcounts in update_ref_for_cow
  btrfs: Fix quota reservation leak on preallocated files

Pull ARM SoC fixes from Olof Johansson:

 - A revert of all SCPI changes from the 4.15 merge window. They had
   regressions on the Amlogic platforms, and the submaintainer isn't
   around to fix these bugs due to vacation, etc. So we agreed to revert
   and revisit in next release cycle.

 - A series fixing a number of bugs for ARM CCN interconnect, around
   module unload, smp_processor_id() in preemptable context, and fixing
   some memory allocation failure checks.

 - A handful of devicetree fixes for different platforms, fixing
   warnings and errors that were previously ignored by the compiler.

 - The usual set of mostly minor fixes for different platforms.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
  arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  firmware: arm_scpi: Revert updates made during v4.15 merge window
  arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
  arm64: dts: sort vendor subdirectories in Makefile alphabetically
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
  MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
  arm64: dts: uniphier: remove unnecessary interrupt-parent
  ...

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - A number of issues in the vgic discovered using SMATCH
   - A bit one-off calculation in out stage base address mask (32-bit
     and 64-bit)
   - Fixes to single-step debugging instructions that trap for other
     reasons such as MMMIO aborts
   - Printing unavailable hyp mode as error
   - Potential spinlock deadlock in the vgic
   - Avoid calling vgic vcpu free more than once
   - Broken bit calculation for big endian systems

 s390:
   - SPDX tags
   - Fence storage key accesses from problem state
   - Make sure that irq_state.flags is not used in the future

  x86:
   - Intercept port 0x80 accesses to prevent host instability (CVE)
   - Use userspace FPU context for guest FPU (mainly an optimization
     that fixes a double use of kernel FPU)
   - Do not leak one page per module load
   - Flush APIC page address cache from MMU invalidation notifiers"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  KVM: x86: fix APIC page invalidation
  KVM: s390: Fix skey emulation permission check
  KVM: s390: mark irq_state.flags as non-usable
  KVM: s390: Remove redundant license text
  KVM: s390: add SPDX identifiers to the remaining files
  KVM: VMX: fix page leak in hardware_setup()
  KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
  x86,kvm: remove KVM emulator get_fpu / put_fpu
  x86,kvm: move qemu/guest FPU switching out to vcpu_run
  KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
  KVM: arm/arm64: kvm_arch_destroy_vm cleanups
  KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
  kvm: arm: don't treat unavailable HYP mode as an error
  KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
  kvm: arm64: handle single-step of hyp emulated mmio instructions
  kvm: arm64: handle single-step during SError exceptions
  kvm: arm64: handle single-step of userspace mmio instructions
  kvm: arm64: handle single-stepping trapped instructions
  KVM: arm/arm64: debug: Introduce helper for single-step
  arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
  ...

* fixes:
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node

Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo

* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: fix UART pclk clock name
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>