Add the necessary dt nodes for gpu support in X1E80100.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240629015111.264564-6-quic_akhilpo@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

According to the power grid documentation, the 0.8v HS PHY shared
regulator is actually LDO3 from PM8550ve id J. Fix both CRD and QCP
boards.

Fixes: d7e03cce ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240629-x1e80100-dts-fix-hsphy-0-8v-supplies-v1-1-de99ee030b27@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Rb3Gen2 has a lt9611uxc DSI-to-HDMI bridge on i2c0, with
reset gpio from pm7250b gpio2 and irq gpio from tlmm gpio24.
Bridge supplies are Vdd connected to input supply directly
and vcc to L11c. Enable HDMI output, bridge and corresponding
DSI output.
Signed-off-by: Venkata Prahlad Valluru <quic_vvalluru@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240528141954.7567-1-quic_vvalluru@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

These are documented and supported everywhere, but not described in DT.
Add them.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240624120849.2550621-2-caleb.connolly@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add fastrpc nodes for ADSP and CDSP on X1E80100 SoC.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20240624100214.189991-1-quic_sibis@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the CPU and LLCC BWMONs on X1E80100 SoCs.
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20240624092214.146935-5-quic_sibis@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add node to support mmc controller inside of IPQ6018.
This controller supports both eMMC and SD cards.

Tested with:
  eMMC (HS200)
  SD Card (SDR50/SDR104)
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20240620150122.1406631-3-amadeus@jmu.edu.cnSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add clocks which need to be enbaled for configuring
QoS on sc7280.
Signed-off-by: Odelu Kukatla <quic_okukatla@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Link: https://lore.kernel.org/r/20240607173927.26321-5-quic_okukatla@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add device nodes for video and camera clock controllers on Qualcomm
SM8650 platform.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-9-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Merge the SM8650 video and clock controller drivers to gain access to
the constants from the DeviceTree binding.

Add support for the camera clock controller for camera clients to
be able to request for camcc clocks on SM8650 platform.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-8-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add device tree bindings for the camera clock controller on
Qualcomm SM8650 platform.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-7-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Update the order of SC8280XP camcc header file in SM8450 camcc
bindings.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-6-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add support to the SM8650 video clock controller by extending
the SM8550 video clock controller, which is mostly identical
but SM8650 has few additional clocks and minor differences.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-5-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add support for videocc XO clk ares for consumer drivers to be
able to request this reset.

Fixes: f53153a3 ("clk: qcom: videocc-sm8550: Add video clock controller driver for SM8550")
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-4-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

SM8650 video clock controller has most clocks same as SM8450,
but it also has few additional clocks and resets. Add device tree
bindings for the video clock controller on Qualcomm SM8650 platform
by defining these additional clocks and resets on top of SM8450.
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-3-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Correct the videocc header file name in SM8450 videocc bindings.

Fixes: 1e910b2b ("dt-bindings: clock: qcom: Add SM8450 video clock controller")
Signed-off-by: Jagadeesh Kona <quic_jkona@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240602114439.1611-2-quic_jkona@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Define the themal zones using the temperature values in stage1 for this
platform so that the spmi-temp-alarm driver becomes active.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240625-pm8916-tz-v1-1-a4c1f61e92dd@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add audio support to QCP platform which includes 2 x Speakers
Headset Mic and Headset support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240624-qcp-audio-v1-1-323a6b5e1fe5@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add a 20MB reserved memory region for use by SCM calls.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20240527-shm-bridge-v10-15-ce7afaa58d3a@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619-smsm-mbox-dts-v1-5-268ab7eef779@lucaweiss.euSigned-off-by: Bjorn Andersson <andersson@kernel.org>

With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619-smsm-mbox-dts-v1-4-268ab7eef779@lucaweiss.euSigned-off-by: Bjorn Andersson <andersson@kernel.org>

With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619-smsm-mbox-dts-v1-3-268ab7eef779@lucaweiss.euSigned-off-by: Bjorn Andersson <andersson@kernel.org>

With the smsm bindings and driver finally supporting mboxes, switch to
that and stop using apcs as syscon.
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619-smsm-mbox-dts-v1-2-268ab7eef779@lucaweiss.euSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add tsens and thermal zones nodes for x1e80100 SoC.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240621-x1e80100-dts-thermal-v3-1-abd6f416b609@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

PM8008 regulators are used for the cameras found on FP5. Configure the
chip and its voltages.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240621-fp4-fp5-pm8008-v1-2-dbedcd6f00f1@fairphone.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

PM8008 regulators are used for the cameras found on FP4. Configure the
chip and its voltages.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240621-fp4-fp5-pm8008-v1-1-dbedcd6f00f1@fairphone.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

There is PM8916 Battery voltage monitor on GPLUS FL8005A.
Add PM8916 BMS and the battery to the device tree.
Signed-off-by: Lin, Meng-Bo <linmengbo06890@proton.me>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240621141319.347088-1-linmengbo06890@proton.meSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add the compatible for this device.
Signed-off-by: Valeriy Klimin <vdos63@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240621-sony-aries-v2-1-dddf10722522@gmail.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Enable the PM8008 PMIC which is used to power the camera sensors.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240608155526.12996-13-johan+linaro@kernel.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add AIM300 AIoT Carrier board DTS support, including usb, UART, PCIe,
I2C functions support.
Here is a diagram of AIM300 AIoT Carrie Board and SoM
 +--------------------------------------------------+
 |             AIM300 AIOT Carrier Board            |
 |                                                  |
 |           +-----------------+                    |
 |power----->| Fixed regulator |---------+          |
 |           +-----------------+         |          |
 |                                       |          |
 |                                       v VPH_PWR  |
 | +----------------------------------------------+ |
 | |                          AIM300 SOM |        | |
 | |                                     |VPH_PWR | |
 | |                                     v        | |
 | |   +-------+       +--------+     +------+    | |
 | |   | UFS   |       | QCS8550|     |PMIC  |    | |
 | |   +-------+       +--------+     +------+    | |
 | |                                              | |
 | +----------------------------------------------+ |
 |                                                  |
 |                    +----+          +------+      |
 |                    |USB |          | UART |      |
 |                    +----+          +------+      |
 +--------------------------------------------------+
Co-developed-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Co-developed-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20240618072202.2516025-5-quic_tengfan@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

AIM300 Series is a highly optimized family of modules designed to
support AIoT applications. It integrates QCS8550 SoC, UFS and PMIC
chip etc.
Here is a diagram of AIM300 SoM:
          +----------------------------------------+
          |AIM300 SoM                              |
          |                                        |
          |                           +-----+      |
          |                      |--->| UFS |      |
          |                      |    +-----+      |
          |                      |                 |
          |                      |                 |
     3.7v |  +-----------------+ |    +---------+  |
  ---------->|       PMIC      |----->| QCS8550 |  |
          |  +-----------------+      +---------+  |
          |                      |                 |
          |                      |                 |
          |                      |    +-----+      |
          |                      |--->| ... |      |
          |                           +-----+      |
          |                                        |
          +----------------------------------------+
Co-developed-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20240618072202.2516025-4-quic_tengfan@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

QCS8550 is derived from SM8550. The difference between SM8550 and
QCS8550 is QCS8550 doesn't have modem RF system. QCS8550 is mainly used
in IoT products.
QCS8550 firmware has different memory map compared to SM8550.
The memory map will be runtime added through bootloader.
There are 3 types of reserved memory regions here:
1. Firmware related regions which aren't shared with kernel.
    The device tree source in kernel doesn't need to have node to indicate
the firmware related reserved information. Bootloader converys the
information by updating devicetree at runtime.
    This will be described as: UEFI saves the physical address of the
UEFI System Table to dts file's chosen node. Kernel read this table and
add reserved memory regions to efi config table. Current reserved memory
region may have reserved region which was not yet used, release note of
the firmware have such kind of information.
2. Firmware related memory regions which are shared with Kernel
    The device tree source in the kernel needs to include nodes that
indicate fimware-related shared information. A label name is suggested
because this type of shared information needs to be referenced by
specific drivers for handling purposes.
    Unlike previous platforms, QCS8550 boots using EFI and describes
most reserved regions in the ESRT memory map. As a result, reserved
memory regions which aren't relevant to the kernel(like the hypervisor
region) don't need to be described in DT.
3. Remoteproc regions.
    Remoteproc regions will be reserved and then assigned to subsystem
firmware later.
Here is a reserved memory map for this platform:
 0x80000000 +-------------------+
            |                   |
            | Firmware Related  |
            |                   |
 0x8a800000 +-------------------+
            |                   |
            | Remoteproc Region |
            |                   |
 0xa7000000 +-------------------+
            |                   |
            | Kernel Available  |
            |                   |
 0xd4d00000 +-------------------+
            |                   |
            | Firmware Related  |
            |                   |
0x100000000 +-------------------+
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20240618072202.2516025-3-quic_tengfan@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Document QCS8550 SoC and the AIM300 AIoT board bindings.
QCS8550 is derived from SM8550. The difference between SM8550 and
QCS8550 is QCS8550 doesn't have modem RF system. QCS8550 is mainly used
in IoT scenarios.
AIM300 Series is a highly optimized family of modules designed to
support AIoT applications. It integrates QCS8550 SoC, UFS and PMIC chip
etc.
AIM stands for Artificial Intelligence Module. AIoT stands for AI IoT.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Tengfei Fan <quic_tengfan@quicinc.com>
Link: https://lore.kernel.org/r/20240618072202.2516025-2-quic_tengfan@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Update the usb interrupts properties to fix the following
bindings check errors:
usb@a6f8800: interrupt-names:0: 'pwr_event' was expected
        from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
usb@a6f8800: interrupt-names:1: 'hs_phy_irq' was expected
	from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
usb@a6f8800: interrupt-names: ['hs_phy_irq', 'ss_phy_irq', 'dm_hs_phy_irq', 'dp_hs_phy_irq'] is too short
        from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#

Fixes: dd1bd5bf ("arm64: dts: qcom: qdu1000: Add USB3 and PHY support")
Cc: Krishna Kurapati <quic_kriskura@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406171241.YKuCm3SC-lkp@intel.com/Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240617115624.29875-1-quic_kbajaj@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Add a node for the PMU module of the QCA6391 present on the RB5 board.
Assign its LDO power outputs to the existing Bluetooth module. Add a
node for the PCIe port to sm8250.dtsi and define the WLAN node on it in
the board's .dts and also make it consume the power outputs of the PMU.

Tested-by: Caleb Connolly <caleb.connolly@linaro.org> # OnePlus 8T
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240605122729.24283-5-brgl@bgdev.plSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Describe the ath12k WLAN on-board the WCN7850 module present on the
board.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240605122729.24283-4-brgl@bgdev.plSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Describe the ath12k WLAN on-board the WCN7850 module present on the
board.

[Neil: authored the initial version of the change]
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240605122729.24283-3-brgl@bgdev.plSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Describe the ath12k WLAN on-board the WCN7850 module present on the
board.

[Neil: authored the initial version of the change]
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240605122729.24283-2-brgl@bgdev.plSigned-off-by: Bjorn Andersson <andersson@kernel.org>

Enable sound and modem for the GPLUS FL8005A.
The setup is similar to most MSM8916 devices, i.e.:

 - QDSP6 audio
 - Earpiece/headphones/microphones via digital/analog codec in
   MSM8916/PM8916
 - WWAN Internet via BAM-DMUX
Signed-off-by: Lin, Meng-Bo <linmengbo06890@proton.me>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619111523.54301-1-linmengbo06890@proton.meSigned-off-by: Bjorn Andersson <andersson@kernel.org>