Support use of the WM8903 IRQ for reporting of microphone presence
and short detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Currently used to detect completion of the write sequencer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Provide support for WM8903 microphone presence and short detection
using the GPIOs to route out a logic signal suitable for handling
using snd_soc_jack_add_gpios() on the processor GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Allow users to pass in a default configuration for the GPIOs of
the WM8903 as platform data. This allows configuration of the pin
muxing of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.

The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Use the new delay calback function to report the delay through
ALSA for application caused by the internal FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

New functions for querying the FIFO caused delay on both
TX and RX path.
On TX path the return value shows the number of used
locations in the FIFO.
On RX papth it returns the number of locations to be filled
to reach the threshold value (DMA will be triggered to read
the data out from the FIFO).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Platform data option for the codec to keep the BCLK clock
continuously running in FIFO modes (codec master).

OMAP3 McBSP when in slave mode needs continuous BCLK running
on the serial bus in order to operate correctly.

Since in FIFO mode the DAC33 can also shut down the BCLK clock
and enable it only when it is needed, let the platforms decide
if the CPU side needs the BCLK running or not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

To avoid race condition especially in FIFO modes the
sequence for enabling and disabling the codec need to
be changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The DM365 EVM has two codecs: the Audio Codec (AIC3x) and the Voice Codec,
the idea is to have both enabled in the same kernel simultaneously. However,
the current soc-core doesn't support simultaneous codecs, once that
support will have added, a patch will be posted to enable both codecs in
the DM365 EVM.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Currently the DM365 is the only SoC that includes this Voice Codec.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds the support for the interface needed by the DaVinci
Voice Codec CQ93VC.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is the MFD driver for the DaVinci Voice codec, it has two clients:

* Voice codec interface
* Voice codec CQ93VC
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

For ASoC, if either CPU or CODEC driver has set the flag, the MACHINE driver
should be given a chance to figure out if the dai, that set the flag, can
accomodate a rate that it does not explicitly specify but is specified
by the dai at the other end of the link.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This driver USE PLL for 11025/22050/44100/88200 rate.
To enable switching to bypass mode, PLL is always turned on.
Special thanks to Phil
Signed-off-by: Phil Edworthy <Phil.Edworthy@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Towards having build for multiple SoCs segregate hw_params callback
for s3c2412 and s3c64xx.
Since, all new SoCs have s3c64xx like register map, we keep that as
default implementation if no SoC specific callback is already defined.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

For some CPU-CODEC and source clock combination we might need to set
BCLK to N*Sample_size*LRCLK, where N may be even 3 or 4, not just 2.

We can simply remove the dependency of BCLK on sample size as there
is already a callback(S3C_I2SV2_DIV_BCLK) available to set required BCLK.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Towards generalizing CPU driver interface, do not accept direct field
values for the BCLK and RCLK.
The machine driver should simply request the FS-multiple and not provide
the value to be set in divide field of IISMOD.

[Confirmed by Jassi that no existing machine drivers are affected --
broonie]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In order for the RATE and FMT defines to be reuseable in future by the
i2sv4 driver, move the MACROs out to the header file.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

s3c64xx-i2s remove unncessary headers
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

s3c-i2s-v2 remove unnecessary headers
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rather than having the multiple definitions of the same clocks,
define them in one common place and refer by SoC specific names.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add missing semicolon after s3c2412_i2s_delay
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

No point in duplicating this structure layout in each driver.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

On TI DM6467 EVM, S/PDIF DIT codec fails to open as it is unable to install
hardware params. This dummy codec has no set_fmt and set_sysclk implementations
and calls from the application to these functions cause errors. This patch adds
a new hardware params callback function for S/PDIF transciever codec.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Phil Edworthy <Phil.Edworthy@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (62 commits)
  msi-laptop: depends on RFKILL
  msi-laptop: Detect 3G device exists by standard ec command
  msi-laptop: Add resume method for set the SCM load again
  msi-laptop: Support some MSI 3G netbook that is need load SCM
  msi-laptop: Add threeg sysfs file for support query 3G state by standard 66/62 ec command
  msi-laptop: Support standard ec 66/62 command on MSI notebook and nebook
  Driver core: create lock/unlock functions for struct device
  sysfs: fix for thinko with sysfs_bin_attr_init()
  sysfs: Kill unused sysfs_sb variable.
  sysfs: Pass super_block to sysfs_get_inode
  driver core: Use sysfs_rename_link in device_rename
  sysfs: Implement sysfs_rename_link
  sysfs: Pack sysfs_dirent more tightly.
  sysfs: Serialize updates to the vfs inode
  sysfs: windfarm: init sysfs attributes
  sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on module dynamic attributes
  sysfs: Document sysfs_attr_init and sysfs_bin_attr_init
  sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on dynamic attributes
  sysfs: Use one lockdep class per sysfs attribute.
  sysfs: Only take active references on attributes.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] i6300esb.c: change platform_driver to pci_driver
  [WATCHDOG] i6300esb: fix unlock register with
  [WATCHDOG] drivers/watchdog/wdt.c:wdt_ioctl(): make `ident' non-static
  [WATCHDOG] change reboot_notifier to platform-shutdown method.
  [WATCHDOG] watchdog_info constify
  [WATCHDOG] gef_wdt: Author corrections following split of GE Fanuc joint venture
  [WATCHDOG] iTCO_wdt: clean up probe(), modify err msg
  [WATCHDOG] ep93xx: watchdog timer driver for TS-72xx SBCs cleanup
  [WATCHDOG] support for max63xx watchdog timer chips
  [WATCHDOG] ep93xx: added platform side support for TS-72xx WDT driver
  [WATCHDOG] ep93xx: implemented watchdog timer driver for TS-72xx SBCs

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
  ALSA: hdmi - show debug message on changing audio infoframe
  ALSA: hdmi - merge common code for intelhdmi and nvhdmi
  ALSA: hda - Add ASRock mobo to MSI blacklist
  ALSA: hda: uninitialized variable fix
  ALSA: hda: Use LPIB for a Biostar Microtech board
  ALSA: usb/audio.h: Fix field order
  ALSA: fix jazz16 compile (udelay)
  ALSA: hda: Use LPIB for Dell Latitude 131L
  ALSA: hda - Build hda_eld into snd-hda-codec module
  ALSA: hda - Support NVIDIA MCP89 and GT21x hdmi audio
  ALSA: hda - Support max codecs to 8 for nvidia hda controller
  ALSA: riptide: clean up while loop
  ALSA: usbaudio - remove debug "SAMPLE BYTES" printk line
  ALSA: timer - pass real event in snd_timer_notify1() to instance callback
  ALSA: oxygen: change || to &&
  ALSA: opti92x: use PnP data to select Master Control port
  ASoC: fix ak4104 register array access
  ASoC: soc_pcm_open: Add missing bailout tag
  ALSA: usbaudio: Fix wrong bitrate for Creative Creative VF0470 Live Cam
  ALSA: ua101: removing debugging code
  ...

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] smsgiucv_app: deliver z/VM CP special messages (SMSG) as uevents
  [S390] smsgiucv: declare char pointers as "const"
  [S390] dasd: automatic recognition of read-only devices
  [S390] remove unused qdio flags in zfcp and qeth
  [S390] Cleanup xtime usage
  [S390] qdio: add missing bracket
  [S390] cio: fix init_count in case of recognition after steal lock
  [S390] dasd: security and PSF update patch for EMC CKD ioctl
  [S390] hvc_iucv: allocate memory buffers for IUCV in zone DMA
  [S390] uaccess: make sure copy_from_user_overflow is builtin

Remove the EXPERIMENTAL flag from FS-Cache so that Ubuntu can make use of the
facility.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since the intel 6300esb platform uses a dedicated PCI ID for
it's watchdog timer (00:1d.4), it's better and easier to have
this as a pci_driver.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".

When the callback is called for special messages, the driver creates
an uevent for the received message.  The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.

udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Declare the smsgiucv prefix char pointer as "const" and use
use const char pointers in callback functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>