- 05 Apr, 2019 11 commits
-
-
Tonghao Zhang authored
[ Upstream commit 24319258 ] If we try to set VFs rate on a VF (not PF) net device, the kernel will be crash. The commands are show as below: $ echo 2 > /sys/class/net/$MLX_PF0/device/sriov_numvfs $ ip link set $MLX_VF0 vf 0 max_tx_rate 2 min_tx_rate 1 If not applied the first patch ("net/mlx5: Avoid panic when setting vport mac, getting vport config"), the command: $ ip link set $MLX_VF0 vf 0 rate 100 can also crash the kernel. [ 1650.006388] RIP: 0010:mlx5_eswitch_set_vport_rate+0x1f/0x260 [mlx5_core] [ 1650.007092] do_setlink+0x982/0xd20 [ 1650.007129] __rtnl_newlink+0x528/0x7d0 [ 1650.007374] rtnl_newlink+0x43/0x60 [ 1650.007407] rtnetlink_rcv_msg+0x2a2/0x320 [ 1650.007484] netlink_rcv_skb+0xcb/0x100 [ 1650.007519] netlink_unicast+0x17f/0x230 [ 1650.007554] netlink_sendmsg+0x2d2/0x3d0 [ 1650.007592] sock_sendmsg+0x36/0x50 [ 1650.007625] ___sys_sendmsg+0x280/0x2a0 [ 1650.007963] __sys_sendmsg+0x58/0xa0 [ 1650.007998] do_syscall_64+0x5b/0x180 [ 1650.009438] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: c9497c98 ("net/mlx5: Add support for setting VF min rate") Cc: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by:
Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Acked-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Douglas Anderson authored
[ Upstream commit 31b265b3 ] As reported back in 2016-11 [1], the "ftdump" kdb command triggers a BUG for "sleeping function called from invalid context". kdb's "ftdump" command wants to call ring_buffer_read_prepare() in atomic context. A very simple solution for this is to add allocation flags to ring_buffer_read_prepare() so kdb can call it without triggering the allocation error. This patch does that. Note that in the original email thread about this, it was suggested that perhaps the solution for kdb was to either preallocate the buffer ahead of time or create our own iterator. I'm hoping that this alternative of adding allocation flags to ring_buffer_read_prepare() can be considered since it means I don't need to duplicate more of the core trace code into "trace_kdb.c" (for either creating my own iterator or re-preparing a ring allocator whose memory was already allocated). NOTE: another option for kdb is to actually figure out how to make it reuse the existing ftrace_dump() function and totally eliminate the duplication. This sounds very appealing and actually works (the "sr z" command can be seen to properly dump the ftrace buffer). The downside here is that ftrace_dump() fully consumes the trace buffer. Unless that is changed I'd rather not use it because it means "ftdump | grep xyz" won't be very useful to search the ftrace buffer since it will throw away the whole trace on the first grep. A future patch to dump only the last few lines of the buffer will also be hard to implement. [1] https://lkml.kernel.org/r/20161117191605.GA21459@google.com Link: http://lkml.kernel.org/r/20190308193205.213659-1-dianders@chromium.orgReported-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Chao Yu authored
[ Upstream commit aadcef64 ] As Jiqun Li reported in bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202883 sometimes, dead lock when make system call SYS_getdents64 with fsync() is called by another process. monkey running on android9.0 1. task 9785 held sbi->cp_rwsem and waiting lock_page() 2. task 10349 held mm_sem and waiting sbi->cp_rwsem 3. task 9709 held lock_page() and waiting mm_sem so this is a dead lock scenario. task stack is show by crash tools as following crash_arm64> bt ffffffc03c354080 PID: 9785 TASK: ffffffc03c354080 CPU: 1 COMMAND: "RxIoScheduler-3" >> #7 [ffffffc01b50fac0] __lock_page at ffffff80081b11e8 crash-arm64> bt 10349 PID: 10349 TASK: ffffffc018b83080 CPU: 1 COMMAND: "BUGLY_ASYNC_UPL" >> #3 [ffffffc01f8cfa40] rwsem_down_read_failed at ffffff8008a93afc PC: 00000033 LR: 00000000 SP: 00000000 PSTATE: ffffffffffffffff crash-arm64> bt 9709 PID: 9709 TASK: ffffffc03e7f3080 CPU: 1 COMMAND: "IntentService[A" >> #3 [ffffffc001e67850] rwsem_down_read_failed at ffffff8008a93afc >> #8 [ffffffc001e67b80] el1_ia at ffffff8008084fc4 PC: ffffff8008274114 [compat_filldir64+120] LR: ffffff80083584d4 [f2fs_fill_dentries+448] SP: ffffffc001e67b80 PSTATE: 80400145 X29: ffffffc001e67b80 X28: 0000000000000000 X27: 000000000000001a X26: 00000000000093d7 X25: ffffffc070d52480 X24: 0000000000000008 X23: 0000000000000028 X22: 00000000d43dfd60 X21: ffffffc001e67e90 X20: 0000000000000011 X19: ffffff80093a4000 X18: 0000000000000000 X17: 0000000000000000 X16: 0000000000000000 X15: 0000000000000000 X14: ffffffffffffffff X13: 0000000000000008 X12: 0101010101010101 X11: 7f7f7f7f7f7f7f7f X10: 6a6a6a6a6a6a6a6a X9: 7f7f7f7f7f7f7f7f X8: 0000000080808000 X7: ffffff800827409c X6: 0000000080808000 X5: 0000000000000008 X4: 00000000000093d7 X3: 000000000000001a X2: 0000000000000011 X1: ffffffc070d52480 X0: 0000000000800238 >> #9 [ffffffc001e67be0] f2fs_fill_dentries at ffffff80083584d0 PC: 0000003c LR: 00000000 SP: 00000000 PSTATE: 000000d9 X12: f48a02ff X11: d4678960 X10: d43dfc00 X9: d4678ae4 X8: 00000058 X7: d4678994 X6: d43de800 X5: 000000d9 X4: d43dfc0c X3: d43dfc10 X2: d46799c8 X1: 00000000 X0: 00001068 Below potential deadlock will happen between three threads: Thread A Thread B Thread C - f2fs_do_sync_file - f2fs_write_checkpoint - down_write(&sbi->node_change) -- 1) - do_page_fault - down_write(&mm->mmap_sem) -- 2) - do_wp_page - f2fs_vm_page_mkwrite - getdents64 - f2fs_read_inline_dir - lock_page -- 3) - f2fs_sync_node_pages - lock_page -- 3) - __do_map_lock - down_read(&sbi->node_change) -- 1) - f2fs_fill_dentries - dir_emit - compat_filldir64 - do_page_fault - down_read(&mm->mmap_sem) -- 2) Since f2fs_readdir is protected by inode.i_rwsem, there should not be any updates in inode page, we're safe to lookup dents in inode page without its lock held, so taking off the lock to improve concurrency of readdir and avoid potential deadlock. Reported-by:
Jiqun Li <jiqun.li@unisoc.com> Signed-off-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
[ Upstream commit fc2b47b5 ] It believe it is a bad idea to hardcode a specific compiler prefix that may or may not be installed on a user's system. It is annoying when testing features that should not require compilers at all. For example, mrproper, headers_install, etc. should work without any compiler. They look like follows on my machine. $ make ARCH=h8300 mrproper ./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found ./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found make: h8300-unknown-linux-gcc: Command not found make: h8300-unknown-linux-gcc: Command not found [ a bunch of the same error messages continue ] $ make ARCH=h8300 headers_install ./scripts/gcc-version.sh: line 26: h8300-unknown-linux-gcc: command not found ./scripts/gcc-version.sh: line 27: h8300-unknown-linux-gcc: command not found make: h8300-unknown-linux-gcc: Command not found HOSTCC scripts/basic/fixdep make: h8300-unknown-linux-gcc: Command not found WRAP arch/h8300/include/generated/uapi/asm/kvm_para.h [ snip ] The solution is to delete this line, or to use cc-cross-prefix like some architectures do. I chose the latter as a moderate fixup. I added an alternative 'h8300-linux-' because it is available at: https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/Signed-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by:
-
Aurelien Aptel authored
[ Upstream commit bc31d0cd ] We have a customer reporting crashes in lock_get_status() with many "Leaked POSIX lock" messages preceeding the crash. Leaked POSIX lock on dev=0x0:0x56 ... Leaked POSIX lock on dev=0x0:0x56 ... Leaked POSIX lock on dev=0x0:0x56 ... Leaked POSIX lock on dev=0x0:0x53 ... Leaked POSIX lock on dev=0x0:0x53 ... Leaked POSIX lock on dev=0x0:0x53 ... Leaked POSIX lock on dev=0x0:0x53 ... POSIX: fl_owner=ffff8900e7b79380 fl_flags=0x1 fl_type=0x1 fl_pid=20709 Leaked POSIX lock on dev=0x0:0x4b ino... Leaked locks on dev=0x0:0x4b ino=0xf911400000029: POSIX: fl_owner=ffff89f41c870e00 fl_flags=0x1 fl_type=0x1 fl_pid=19592 stack segment: 0000 [#1] SMP Modules linked in: binfmt_misc msr tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag rpcsec_gss_krb5 arc4 ecb auth_rpcgss nfsv4 md4 nfs nls_utf8 lockd grace cifs sunrpc ccm dns_resolver fscache af_packet iscsi_ibft iscsi_boot_sysfs vmw_vsock_vmci_transport vsock xfs libcrc32c sb_edac edac_core crct10dif_pclmul crc32_pclmul ghash_clmulni_intel drbg ansi_cprng vmw_balloon aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd joydev pcspkr vmxnet3 i2c_piix4 vmw_vmci shpchp fjes processor button ac btrfs xor raid6_pq sr_mod cdrom ata_generic sd_mod ata_piix vmwgfx crc32c_intel drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm serio_raw ahci libahci drm libata vmw_pvscsi sg dm_multipath dm_mod scsi_dh_rdac scsi_dh_emc scsi_dh_alua scsi_mod autofs4 Supported: Yes CPU: 6 PID: 28250 Comm: lsof Not tainted 4.4.156-94.64-default #1 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/05/2016 task: ffff88a345f28740 ti: ffff88c74005c000 task.ti: ffff88c74005c000 RIP: 0010:[<ffffffff8125dcab>] [<ffffffff8125dcab>] lock_get_status+0x9b/0x3b0 RSP: 0018:ffff88c74005fd90 EFLAGS: 00010202 RAX: ffff89bde83e20ae RBX: ffff89e870003d18 RCX: 0000000049534f50 RDX: ffffffff81a3541f RSI: ffffffff81a3544e RDI: ffff89bde83e20ae RBP: 0026252423222120 R08: 0000000020584953 R09: 000000000000ffff R10: 0000000000000000 R11: ffff88c74005fc70 R12: ffff89e5ca7b1340 R13: 00000000000050e5 R14: ffff89e870003d30 R15: ffff89e5ca7b1340 FS: 00007fafd64be800(0000) GS:ffff89f41fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000001c80018 CR3: 000000a522048000 CR4: 0000000000360670 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Stack: 0000000000000208 ffffffff81a3d6b6 ffff89e870003d30 ffff89e870003d18 ffff89e5ca7b1340 ffff89f41738d7c0 ffff89e870003d30 ffff89e5ca7b1340 ffffffff8125e08f 0000000000000000 ffff89bc22b67d00 ffff88c74005ff28 Call Trace: [<ffffffff8125e08f>] locks_show+0x2f/0x70 [<ffffffff81230ad1>] seq_read+0x251/0x3a0 [<ffffffff81275bbc>] proc_reg_read+0x3c/0x70 [<ffffffff8120e456>] __vfs_read+0x26/0x140 [<ffffffff8120e9da>] vfs_read+0x7a/0x120 [<ffffffff8120faf2>] SyS_read+0x42/0xa0 [<ffffffff8161cbc3>] entry_SYSCALL_64_fastpath+0x1e/0xb7 When Linux closes a FD (close(), close-on-exec, dup2(), ...) it calls filp_close() which also removes all posix locks. The lock struct is initialized like so in filp_close() and passed down to cifs ... lock.fl_type = F_UNLCK; lock.fl_flags = FL_POSIX | FL_CLOSE; lock.fl_start = 0; lock.fl_end = OFFSET_MAX; ... Note the FL_CLOSE flag, which hints the VFS code that this unlocking is done for closing the fd. filp_close() locks_remove_posix(filp, id); vfs_lock_file(filp, F_SETLK, &lock, NULL); return filp->f_op->lock(filp, cmd, fl) => cifs_lock() rc = cifs_setlk(file, flock, type, wait_flag, posix_lck, lock, unlock, xid); rc = server->ops->mand_unlock_range(cfile, flock, xid); if (flock->fl_flags & FL_POSIX && !rc) rc = locks_lock_file_wait(file, flock) Notice how we don't call locks_lock_file_wait() which does the generic VFS lock/unlock/wait work on the inode if rc != 0. If we are closing the handle, the SMB server is supposed to remove any locks associated with it. Similarly, cifs.ko frees and wakes up any lock and lock waiter when closing the file: cifs_close() cifsFileInfo_put(file->private_data) /* * Delete any outstanding lock records. We'll lose them when the file * is closed anyway. */ down_write(&cifsi->lock_sem); list_for_each_entry_safe(li, tmp, &cifs_file->llist->locks, llist) { list_del(&li->llist); cifs_del_lock_waiters(li); kfree(li); } list_del(&cifs_file->llist->llist); kfree(cifs_file->llist); up_write(&cifsi->lock_sem); So we can safely ignore unlocking failures in cifs_lock() if they happen with the FL_CLOSE flag hint set as both the server and the client take care of it during the actual closing. This is not a proper fix for the unlocking failure but it's safe and it seems to prevent the lock leakages and crashes the customer experiences. Signed-off-by:
Aurelien Aptel <aaptel@suse.com> Signed-off-by:
NeilBrown <neil@brown.name> Signed-off-by:
Steve French <stfrench@microsoft.com> Acked-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
-
Yang Shi authored
commit a7f40cfe upstream. When MPOL_MF_STRICT was specified and an existing page was already on a node that does not follow the policy, mbind() should return -EIO. But commit 6f4576e3 ("mempolicy: apply page table walker on queue_pages_range()") broke the rule. And commit c8633798 ("mm: mempolicy: mbind and migrate_pages support thp migration") didn't return the correct value for THP mbind() too. If MPOL_MF_STRICT is set, ignore vma_migratable() to make sure it reaches queue_pages_to_pte_range() or queue_pages_pmd() to check if an existing page was already on a node that does not follow the policy. And, non-migratable vma may be used, return -EIO too if MPOL_MF_MOVE or MPOL_MF_MOVE_ALL was specified. Tested with https://github.com/metan-ucw/ltp/blob/master/testcases/kernel/syscalls/mbind/mbind02.c [akpm@linux-foundation.org: tweak code comment] Link: http://lkml.kernel.org/r/1553020556-38583-1-git-send-email-yang.shi@linux.alibaba.com Fixes: 6f4576e3 ("mempolicy: apply page table walker on queue_pages_range()") Signed-off-by:
Yang Shi <yang.shi@linux.alibaba.com> Signed-off-by:
Oscar Salvador <osalvador@suse.de> Reported-by:
Cyril Hrubis <chrubis@suse.cz> Suggested-by:
Kirill A. Shutemov <kirill@shutemov.name> Acked-by:
Rafael Aquini <aquini@redhat.com> Reviewed-by:
David Rientjes <rientjes@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Razvan Stefanescu authored
commit 69646d7a upstream. In half-duplex operation, RX should be started after TX completes. If DMA is used, there is a case when the DMA transfer completes but the TX FIFO is not emptied, so the RX cannot be restarted just yet. Use a boolean variable to store this state and rearm TX interrupt mask to be signaled again that the transfer finished. In interrupt transmit handler this variable is used to start RX. A warning message is generated if RX is activated before TX fifo is cleared. Fixes: b389f173 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done") Signed-off-by:
Razvan Stefanescu <razvan.stefanescu@microchip.com> Acked-by:
Richard Genoud <richard.genoud@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Razvan Stefanescu authored
commit f3040983 upstream. Use a helper function to check that a port needs to use half duplex communication, replacing several occurrences of multi-line bit checking. Fixes: b389f173 ("tty/serial: atmel: RS485 half duplex w/DMA: enable RX after TX is done") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Peter Zijlstra authored
commit f8ae107e upstream. The initial value (@M) compute is: m = 1UL << (BITS_PER_LONG - 2); while (m > x) m >>= 2; Which is a linear search for the highest even bit smaller or equal to @x We can implement this using a binary search using __fls() (or better when its hardware implemented). m = 1UL << (__fls(x) & ~1UL); Especially for small values of @x; which are the more common arguments when doing a CDF on idle times; the linear search is near to worst case, while the binary search of __fls() is a constant 6 (or 5 on 32bit) branches. cycles: branches: branch-misses: PRE: hot: 43.633557 +- 0.034373 45.333132 +- 0.002277 0.023529 +- 0.000681 cold: 207.438411 +- 0.125840 45.333132 +- 0.002277 6.976486 +- 0.004219 SOFTWARE FLS: hot: 29.576176 +- 0.028850 26.666730 +- 0.004511 0.019463 +- 0.000663 cold: 165.947136 +- 0.188406 26.666746 +- 0.004511 6.133897 +- 0.004386 HARDWARE FLS: hot: 24.720922 +- 0.025161 20.666784 +- 0.004509 0.020836 +- 0.000677 cold: 132.777197 +- 0.127471 20.666776 +- 0.004509 5.080285 +- 0.003874 Averages computed over all values <128k using a LFSR to generate order. Cold numbers have a LFSR based branch trace buffer 'confuser' ran between each int_sqrt() invocation. Link: http://lkml.kernel.org/r/20171020164644.936577234@infradead.orgSigned-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Suggested-by:
Joe Perches <joe@perches.com> Acked-by:
Will Deacon <will.deacon@arm.com> Acked-by:
-
zhangyi (F) authored
commit 5e86bdda upstream. Currently, we are releasing the indirect buffer where we are done with it in ext4_ind_remove_space(), so we can see the brelse() and BUFFER_TRACE() everywhere. It seems fragile and hard to read, and we may probably forget to release the buffer some day. This patch cleans up the code by putting of the code which releases the buffers to the end of the function. Signed-off-by:
zhangyi (F) <yi.zhang@huawei.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Jari Ruusu <jari.ruusu@gmail.com> Signed-off-by:
-
Will Deacon authored
commit b9a4b9d0 upstream. FAR_EL1 is UNKNOWN for all debug exceptions other than those caused by taking a hardware watchpoint. Unfortunately, if a debug handler returns a non-zero value, then we will propagate the UNKNOWN FAR value to userspace via the si_addr field of the SIGTRAP siginfo_t. Instead, let's set si_addr to take on the PC of the faulting instruction, which we have available in the current pt_regs. Cc: <stable@vger.kernel.org> Reviewed-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
- 03 Apr, 2019 29 commits
-
-
Greg Kroah-Hartman authored
-
Cornelia Huck authored
commit 50b7f1b7 upstream. When we get an interrupt for a channel program, it is not necessarily the final interrupt; for example, the issuing guest may request an intermediate interrupt by specifying the program-controlled-interrupt flag on a ccw. We must not switch the state to idle if the interrupt is not yet final; even more importantly, we must not free the translated channel program if the interrupt is not yet final, or the host can crash during cp rewind. Fixes: e5f84dba ("vfio: ccw: return I/O results asynchronously") Cc: stable@vger.kernel.org # v4.12+ Reviewed-by:
Eric Farman <farman@linux.ibm.com> Signed-off-by:
Cornelia Huck <cohuck@redhat.com> Signed-off-by:
-
Greg Kroah-Hartman authored
commit cf4df407 upstream. This reverts commit 32fd87b3. Alan wrote a better fix for this... Cc: Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Sean Christopherson authored
commit 0cf9135b upstream. The CPUID flag ARCH_CAPABILITIES is unconditioinally exposed to host userspace for all x86 hosts, i.e. KVM advertises ARCH_CAPABILITIES regardless of hardware support under the pretense that KVM fully emulates MSR_IA32_ARCH_CAPABILITIES. Unfortunately, only VMX hosts handle accesses to MSR_IA32_ARCH_CAPABILITIES (despite KVM_GET_MSRS also reporting MSR_IA32_ARCH_CAPABILITIES for all hosts). Move the MSR_IA32_ARCH_CAPABILITIES handling to common x86 code so that it's emulated on AMD hosts. Fixes: 1eaafe91 ("kvm: x86: IA32_ARCH_CAPABILITIES is always supported") Cc: stable@vger.kernel.org Reported-by:
Xiaoyao Li <xiaoyao.li@linux.intel.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Sean Christopherson authored
commit ddba9180 upstream. KVM's API requires thats ioctls must be issued from the same process that created the VM. In other words, userspace can play games with a VM's file descriptors, e.g. fork(), SCM_RIGHTS, etc..., but only the creator can do anything useful. Explicitly reject device ioctls that are issued by a process other than the VM's creator, and update KVM's API documentation to extend its requirements to device ioctls. Fixes: 852b6d57 ("kvm: add device control API") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Thomas Gleixner authored
commit bebd024e upstream. The SMT disable 'nosmt' command line argument is not working properly when CONFIG_HOTPLUG_CPU is disabled. The teardown of the sibling CPUs which are required to be brought up due to the MCE issues, cannot work. The CPUs are then kept in a half dead state. As the 'nosmt' functionality has become popular due to the speculative hardware vulnerabilities, the half torn down state is not a proper solution to the problem. Enforce CONFIG_HOTPLUG_CPU=y when SMP is enabled so the full operation is possible. Reported-by:
Tianyu Lan <Tianyu.Lan@microsoft.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Acked-by:
-
Thomas Gleixner authored
commit 206b9235 upstream. Tianyu reported a crash in a CPU hotplug teardown callback when booting a kernel which has CONFIG_HOTPLUG_CPU disabled with the 'nosmt' boot parameter. It turns out that the SMP=y CONFIG_HOTPLUG_CPU=n case has been broken forever in case that a bringup callback fails. Unfortunately this issue was not recognized when the CPU hotplug code was reworked, so the shortcoming just stayed in place. When a bringup callback fails, the CPU hotplug code rolls back the operation and takes the CPU offline. The 'nosmt' command line argument uses a bringup failure to abort the bringup of SMT sibling CPUs. This partial bringup is required due to the MCE misdesign on Intel CPUs. With CONFIG_HOTPLUG_CPU=y the rollback works perfectly fine, but CONFIG_HOTPLUG_CPU=n lacks essential mechanisms to exercise the low level teardown of a CPU including the synchronizations in various facilities like RCU, NOHZ and others. As a consequence the teardown callbacks which must be executed on the outgoing CPU within stop machine with interrupts disabled are executed on the control CPU in interrupt enabled and preemptible context causing the kernel to crash and burn. The pre state machine code has a different failure mode which is more subtle and resulting in a less obvious use after free crash because the control side frees resources which are still in use by the undead CPU. But this is not a x86 only problem. Any architecture which supports the SMP=y HOTPLUG_CPU=n combination suffers from the same issue. It's just less likely to be triggered because in 99.99999% of the cases all bringup callbacks succeed. The easy solution of making HOTPLUG_CPU mandatory for SMP is not working on all architectures as the following architectures have either no hotplug support at all or not all subarchitectures support it: alpha, arc, hexagon, openrisc, riscv, sparc (32bit), mips (partial). Crashing the kernel in such a situation is not an acceptable state either. Implement a minimal rollback variant by limiting the teardown to the point where all regular teardown callbacks have been invoked and leave the CPU in the 'dead' idle state. This has the following consequences: - the CPU is brought down to the point where the stop_machine takedown would happen. - the CPU stays there forever and is idle - The CPU is cleared in the CPU active mask, but not in the CPU online mask which is a legit state. - Interrupts are not forced away from the CPU - All facilities which only look at online mask would still see it, but that is the case during normal hotplug/unplug operations as well. It's just a (way) longer time frame. This will expose issues, which haven't been exposed before or only seldom, because now the normally transient state of being non active but online is a permanent state. In testing this exposed already an issue vs. work queues where the vmstat code schedules work on the almost dead CPU which ends up in an unbound workqueue and triggers 'preemtible context' warnings. This is not a problem of this change, it merily exposes an already existing issue. Still this is better than crashing fully without a chance to debug it. This is mainly thought as workaround for those architectures which do not support HOTPLUG_CPU. All others should enforce HOTPLUG_CPU for SMP. Fixes: 2e1a3483 ("cpu/hotplug: Split out the state walk into functions") Reported-by:
-
Adrian Hunter authored
commit f3b4e06b upstream. A TSC packet can slip past MTC packets so that the timestamp appears to go backwards. One estimate is that can be up to about 40 CPU cycles, which is certainly less than 0x1000 TSC ticks, but accept slippage an order of magnitude more to be on the safe side. Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org Fixes: 79b58424 ("perf tools: Add Intel PT support for decoding MTC packets") Link: http://lkml.kernel.org/r/20190325135135.18348-1-adrian.hunter@intel.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Lars Persson authored
commit d2b2c6dd upstream. Our MIPS 1004Kc SoCs were seeing random userspace crashes with SIGILL and SIGSEGV that could not be traced back to a userspace code bug. They had all the magic signs of an I/D cache coherency issue. Now recently we noticed that the /proc/sys/vm/compact_memory interface was quite efficient at provoking this class of userspace crashes. Studying the code in mm/migrate.c there is a distinction made between migrating a page that is mapped at the instant of migration and one that is not mapped. Our problem turned out to be the non-mapped pages. For the non-mapped page the code performs a copy of the page content and all relevant meta-data of the page without doing the required D-cache maintenance. This leaves dirty data in the D-cache of the CPU and on the 1004K cores this data is not visible to the I-cache. A subsequent page-fault that triggers a mapping of the page will happily serve the process with potentially stale code. What about ARM then, this bug should have seen greater exposure? Well ARM became immune to this flaw back in 2010, see commit c0177800 ("ARM: 6379/1: Assume new page cache pages have dirty D-cache"). My proposed fix moves the D-cache maintenance inside move_to_new_page to make it common for both cases. Link: http://lkml.kernel.org/r/20190315083502.11849-1-larper@axis.com Fixes: 97ee0524 ("flush cache before installing new page at migraton") Signed-off-by:
Lars Persson <larper@axis.com> Reviewed-by:
Paul Burton <paul.burton@mips.com> Acked-by:
Mel Gorman <mgorman@techsingularity.net> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Romain Izard authored
commit 93e1c8a6 upstream. When the kernel is compiled with preemption enabled, the URB completion handler can run in parallel with the work responsible for waking up the tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the call to tty_port_tty_wakeup() to signal that there is room for additional input, it will be cleared at the end of this call. As a result, TX traffic on the upper layer will be blocked. This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast modem connected with PPP running over a USB CDC-ACM port. Use test_and_clear_bit() instead, which ensures that each wakeup requested by the URB completion code will trigger a call to tty_port_tty_wakeup(). Fixes: 1aba579f cdc-acm: handle read pipe errors Signed-off-by:
Romain Izard <romain.izard.pro@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
Mathias Nyman authored
commit 6cbcf596 upstream. A suspended SS port in U3 link state will go to U0 when resumed, but can almost immediately after that enter U1 or U2 link power save states before host controller driver reads the port status. Host controller driver only checks for U0 state, and might miss the finished resume, leaving flags unclear and skip notifying usb code of the wake. Add U1 and U2 to the possible link states when checking for finished port resume. Cc: stable <stable@vger.kernel.org> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Yasushi Asano authored
commit 40fc1653 upstream. When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN Adapter, warning messages filled up dmesg. [ 101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk? [ 101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk? [ 101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk? Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue. Signed-off-by:
Yasushi Asano <yasano@jp.adit-jv.com> Signed-off-by:
Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com> Acked-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Fabrizio Castro authored
commit 238e0268 upstream. There are cases where multiple device tree nodes point to the same phy node by means of the "phys" property, but we should only consider those nodes that are marked as available rather than just any node. Fixes: 98bfb394 ("usb: of: add an api to get dr_mode by the phy node") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by:
Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by:
-
Radoslav Gerganov authored
commit 072684e8 upstream. In f_hidg_write() the write_spinlock is acquired before calling usb_ep_queue() which causes a deadlock when dummy_hcd is being used. This is because dummy_queue() callbacks into f_hidg_req_complete() which tries to acquire the same spinlock. This is (part of) the backtrace when the deadlock occurs: 0xffffffffc06b1410 in f_hidg_req_complete 0xffffffffc06a590a in usb_gadget_giveback_request 0xffffffffc06cfff2 in dummy_queue 0xffffffffc06a4b96 in usb_ep_queue 0xffffffffc06b1eb6 in f_hidg_write 0xffffffff8127730b in __vfs_write 0xffffffff812774d1 in vfs_write 0xffffffff81277725 in SYSC_write Fix this by releasing the write_spinlock before calling usb_ep_queue() Reviewed-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by:
Radoslav Gerganov <rgerganov@vmware.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Arnd Bergmann authored
commit 3d54d10c upstream. When EXTCON is a loadable module, mtu3 fails to link as built-in: drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe': mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle' Add a Kconfig dependency to force mtu3 also to be a loadable module if extconn is, but still allow it to be built without extcon. Fixes: d0ed062a ("usb: mtu3: dual-role mode support") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Chen-Yu Tsai authored
commit 1396929e upstream. While only the first PHY supports mode switching, the remaining PHYs work in USB host mode. They should support set_mode with mode=USB_HOST instead of failing. This is especially needed now that the USB core does set_mode for all USB ports, which was added in commit b97a3134 ("usb: core: comply to PHY framework"). Make set_mode with mode=USB_HOST a no-op instead of failing for the non-OTG USB PHYs. Fixes: 6ba43c29 ("phy-sun4i-usb: Add support for phy_set_mode") Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Axel Lin authored
commit c5bc6e52 upstream. Current code test wrong value so it does not verify if the written data is correctly read back. Fix it. Also make it return -EPERM if read value does not match written bit, just like it done for adnp_gpio_direction_output(). Fixes: 5e969a40 ("gpio: Add Avionic Design N-bit GPIO expander support") Cc: <stable@vger.kernel.org> Signed-off-by:
Axel Lin <axel.lin@ingics.com> Reviewed-by:
Thierry Reding <thierry.reding@gmail.com> Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
-
Kangjie Lu authored
commit 7ecced09 upstream. ida_simple_get may fail and return a negative error number. The fix checks its return value; if it fails, go to err_destroy. Cc: <stable@vger.kernel.org> Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Signed-off-by:
-
Eric Biggers authored
commit 21d2b122 upstream. If drm_gem_handle_create() fails in vgem_gem_create(), then the drm_vgem_gem_object is freed twice: once when the reference is dropped by drm_gem_object_put_unlocked(), and again by __vgem_gem_destroy(). This was hit by syzkaller using fault injection. Fix it by skipping the second free. Reported-by: syzbot+e73f2fb5ed5a5df36d33@syzkaller.appspotmail.com Fixes: af33a919 ("drm/vgem: Enable dmabuf import interfaces") Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Laura Abbott <labbott@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org Signed-off-by:
Eric Biggers <ebiggers@google.com> Acked-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190226214451.195123-1-ebiggers@kernel.orgSigned-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
YueHaibing authored
commit 23da9588 upstream. Syzkaller reports: kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] SMP KASAN PTI CPU: 1 PID: 5373 Comm: syz-executor.0 Not tainted 5.0.0-rc8+ #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 RIP: 0010:put_links+0x101/0x440 fs/proc/proc_sysctl.c:1599 Code: 00 0f 85 3a 03 00 00 48 8b 43 38 48 89 44 24 20 48 83 c0 38 48 89 c2 48 89 44 24 28 48 b8 00 00 00 00 00 fc ff df 48 c1 ea 03 <80> 3c 02 00 0f 85 fe 02 00 00 48 8b 74 24 20 48 c7 c7 60 2a 9d 91 RSP: 0018:ffff8881d828f238 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: ffff8881e01b1140 RCX: ffffffff8ee98267 RDX: 0000000000000007 RSI: ffffc90001479000 RDI: ffff8881e01b1178 RBP: dffffc0000000000 R08: ffffed103ee27259 R09: ffffed103ee27259 R10: 0000000000000001 R11: ffffed103ee27258 R12: fffffffffffffff4 R13: 0000000000000006 R14: ffff8881f59838c0 R15: dffffc0000000000 FS: 00007f072254f700(0000) GS:ffff8881f7100000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fff8b286668 CR3: 00000001f0542002 CR4: 00000000007606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: drop_sysctl_table+0x152/0x9f0 fs/proc/proc_sysctl.c:1629 get_subdir fs/proc/proc_sysctl.c:1022 [inline] __register_sysctl_table+0xd65/0x1090 fs/proc/proc_sysctl.c:1335 br_netfilter_init+0xbc/0x1000 [br_netfilter] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x462e99 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f072254ec58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99 RDX: 0000000000000000 RSI: 0000000020000280 RDI: 0000000000000003 RBP: 00007f072254ec70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f072254f6bc R13: 00000000004bcefa R14: 00000000006f6fb0 R15: 0000000000000004 Modules linked in: br_netfilter(+) dvb_usb_dibusb_mc_common dib3000mc dibx000_common dvb_usb_dibusb_common dvb_usb_dw2102 dvb_usb classmate_laptop palmas_regulator cn videobuf2_v4l2 v4l2_common snd_soc_bd28623 mptbase snd_usb_usx2y snd_usbmidi_lib snd_rawmidi wmi libnvdimm lockd sunrpc grace rc_kworld_pc150u rc_core rtc_da9063 sha1_ssse3 i2c_cros_ec_tunnel adxl34x_spi adxl34x nfnetlink lib80211 i5500_temp dvb_as102 dvb_core videobuf2_common videodev media videobuf2_vmalloc videobuf2_memops udc_core lnbp22 leds_lp3952 hid_roccat_ryos s1d13xxxfb mtd vport_geneve openvswitch nf_conncount nf_nat_ipv6 nsh geneve udp_tunnel ip6_udp_tunnel snd_soc_mt6351 sis_agp phylink snd_soc_adau1761_spi snd_soc_adau1761 snd_soc_adau17x1 snd_soc_core snd_pcm_dmaengine ac97_bus snd_compress snd_soc_adau_utils snd_soc_sigmadsp_regmap snd_soc_sigmadsp raid_class hid_roccat_konepure hid_roccat_common hid_roccat c2port_duramar2150 core mdio_bcm_unimac iptable_security iptable_raw iptable_mangle iptable_nat nf_nat_ipv4 nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter bpfilter ip6_vti ip_vti ip_gre ipip sit tunnel4 ip_tunnel hsr veth netdevsim devlink vxcan batman_adv cfg80211 rfkill chnl_net caif nlmon dummy team bonding vcan bridge stp llc ip6_gre gre ip6_tunnel tunnel6 tun crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel joydev mousedev ide_pci_generic piix aesni_intel aes_x86_64 ide_core crypto_simd atkbd cryptd glue_helper serio_raw ata_generic pata_acpi i2c_piix4 floppy sch_fq_codel ip_tables x_tables ipv6 [last unloaded: lm73] Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 770020de38961fd0 ]--- A new dir entry can be created in get_subdir and its 'header->parent' is set to NULL. Only after insert_header success, it will be set to 'dir', otherwise 'header->parent' is set to NULL and drop_sysctl_table is called. However in err handling path of get_subdir, drop_sysctl_table also be called on 'new->header' regardless its value of parent pointer. Then put_links is called, which triggers NULL-ptr deref when access member of header->parent. In fact we have multiple error paths which call drop_sysctl_table() there, upon failure on insert_links() we also call drop_sysctl_table().And even in the successful case on __register_sysctl_table() we still always call drop_sysctl_table().This patch fix it. Link: http://lkml.kernel.org/r/20190314085527.13244-1-yuehaibing@huawei.com Fixes: 0e47c99d ("sysctl: Replace root_list with links between sysctl_table_sets") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reported-by:
Hulk Robot <hulkci@huawei.com> Acked-by:
Luis Chamberlain <mcgrof@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> [3.4+] Signed-off-by:
-
Wentao Wang authored
commit 3ec80029 upstream. Echo "" to /sys/module/kgdboc/parameters/kgdboc will fail with "No such device” error. This is caused by function "configure_kgdboc" who init err to ENODEV when the config is empty (legal input) the code go out with ENODEV returned. Fixes: 2dd45316 ("kgdboc: Fix restrict error") Signed-off-by:
Wentao Wang <witallwang@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by:
-
Bjørn Mork authored
commit 84f3b43f upstream. This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Cc: stable@vger.kernel.org Signed-off-by:
Bjørn Mork <bjorn@mork.no> [ johan: use tabs to align comments in adjacent lines ] Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Kristian Evensen authored
commit d1252f02 upstream. The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the same way as the EP06 (including the dynamic configuration behavior), so the same checks on reserved interfaces, etc. are needed. Signed-off-by:
Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mans Rullgard authored
commit f8df5c2c upstream. The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4 of which are serial ports. The fifth is a network interface supported by the qmi-wwan driver. Furthermore, the serial ports do not support modem control signals. Add driver_info flags to reflect this. Signed-off-by:
Mans Rullgard <mans@mansr.com> Fixes: ec0cd94d ("usb: option: add SIMCom SIM5218") Cc: stable <stable@vger.kernel.org> # 3.2 Signed-off-by:
-
Lin Yi authored
commit 2908b076 upstream. The write_parport_reg_nonblock() helper takes a reference to the struct mos_parport, but failed to release it in a couple of error paths after allocation failures, leading to a memory leak. Johan said that move the kref_get() and mos_parport assignment to the end of urbtrack initialisation is a better way, so move it. and mos_parport do not used until urbtrack initialisation. Signed-off-by:
Lin Yi <teroincn@163.com> Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Signed-off-by:
-
George McCollister authored
commit 422c2537 upstream. Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be automatically detected. Signed-off-by:
George McCollister <george.mccollister@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
commit a595ecdd upstream. Lorenz Messtechnik has a device that is controlled by the cp210x driver, so add the device id to the driver. The device id was provided by Silicon-Labs for the devices from this vendor. Reported-by:
Uli <t9cpu@web.de> Signed-off-by:
-
Hoan Nguyen An authored
commit 93bcefd4 upstream. We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted (if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer, re-enable the SCSCR_TIE bit, which was done at sci_start_tx(). This is unnecessary processing, wasting CPU operation if the data transmission length is large. And further, transmit end, FIFO empty bits disabling have also been performed in the step above. Signed-off-by:
Hoan Nguyen An <na-hoan@jinso.co.jp> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Aditya Pakki authored
commit 3a10e3dd upstream. of_match_device can return a NULL pointer when matching device is not found. This patch avoids a scenario causing NULL pointer derefernce. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
