- 17 Feb, 2007 13 commits
-
-
Bartlomiej Zolnierkiewicz authored
->init_dma() cannot be called with dmabase == 0 (see drivers/ide/setup-pci.c) Signed-off-by:Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Bartlomiej Zolnierkiewicz authored
In drivers/ide/Kconfig BLK_DEV_TRM290 depends on BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on). Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
'speed' is always equal to 'mode' when ide_config_drive_speed() is called Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
CONFIG_PDC202XX_MASTER config option doesn't exist Signed-off-by: -
Kou Ishizaki authored
This is the patch (based on 2.6.19-rc4) for PATA controller of Toshiba Cell reference set(Celleb). The reference set consists of Cell, 512MB memory, Super Companion Chip(SCC) and some peripherals such as HDD, GbE, etc. You can see brief explanation and picture of Cell reference set at following URLs. http://www.toshiba.co.jp/about/press/2005_09/pr2001.htm http://cell-industries.com/toshiba_announces.php We use a drivers/ide driver because its design is more suitable for SCC IDE controller than libata driver. Since SCC supports only 32bit read/write, we must override many callbacks of ata_port_operations by modifying generic helpers. Each time the libata common code is updated, we must update those modified helpers. It is very hard for us. But we will try to implement the libata driver as needed. Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp> Signed-off-by: -
Sergei Shtylyov authored
Fix a number of issues with the DMA support code: - driver claims support for all SW/MW DMA modes while supporting only MWDMA2; - ide_dma_check() method tries to enable DMA on the "known good" drives which don't support MWDMA2; - ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already tuned PIO mode and calls ide_dma_off() method instead of returning error; - ide_dma_off() method sets drive->current_speed while it doesn't actually change (only the PIO timings are re-loaded into the chip's registers); - init_hwif() method forcibly sets/resets both "drive DMA capable" bits while this is properly handled by ide_dma_{on,off}() methods being called later... Signed-off-by:Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Sergei Shtylyov authored
Fix the driver's tuneproc() method to always set the PIO mode requested and not pick the best possible one, rename it to pdc202xx_tune_drive(), and change the calls to it accordingly; remove the preceding comment which has nothing to do with the code. Sergei Shtylyov wrote: > The tuneproc() method should take arg 255 for auto-selecting the best PIO > mode, not 5 as it did here + this driver's method always auto-selected instead > of setting the mode it's been told to -- issue typical to drivers/ide/... Signed-off-by:
-
Sergei Shtylyov authored
Fix two typos found by SiI680A documentation check. They caused the taskfile transfer overclocking: - in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers; - in PIO mode 2 as data and taskfile timings are swapped when writing to the MMIO regs. Fix coding style and trailing whitespace in enclosing statements while at it... Signed-off-by:
-
Albert Lee authored
patch 2/2: Remove clearing bmdma status from cdrom_decode_status() since ATA devices might need it as well. (http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94) Signed-off-by:
Albert Lee <albertcc@tw.ibm.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: "Adam W. Hawks" <awhawks@us.ibm.com> Signed-off-by:
-
Albert Lee authored
patch 1/2 (revised): - Fix drive->waiting_for_dma to work with CDB-intr devices. - Do the dma status clearing in ide_intr() and add a new hwif->ide_dma_clear_irq for Intel ICHx controllers. Revised per Alan, Sergei and Bart's advice. Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters. Please review/apply, thanks. Signed-off-by:
-
Alan Cox authored
A ZIP or similar with unformatted media will cause crashes when attempts are made to read/write it in some cases. This is because bs_factor is zero and we divide by it causing an oops. As the size of a non-accessible/non-existant media is really a bit of a zen question it doesn't matter if non-existant media is 512 bytes per sector or zero. Setting it to 1 causes us to generate 512 bytes/sector accesses and error properly. Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh) Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0, atiixp_dma_check() will tune the correct PIO mode anyway * jmicron: if DMA can't be used config_chipset_for_dma() should return 0, micron_config_drive_for_dma() will tune the correct PIO mode anyway config_jmicron_chipset_for_pio(drive, !speed) doesn't program device transfer mode for speed != 0 (only wastes some CPU cycles on ide_get_best_pio_mode() call) so remove it * triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0, triflex_config_drive_xfer_rate() will tune correct PIO mode anyway Above changes also fix (theoretical) issue when ->speedproc fails to set device transfer mode (i.e. when ide_config_drive_speed() fails to program it) but one of DMA transfer modes is already enabled on the device by the BIOS. In such scenario ide_dma_enable() will incorrectly return true statement and ->ide_dma_check will try to enable DMA on the device. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* remember to clear reg2 bits for the current device before setting mode * remove no longer needed hpt34x_clear_chipset() Signed-off-by:
-
- 16 Feb, 2007 27 commits
-
-
git://www.atmel.no/~hskinnemoen/linux/kernel/avr32Linus Torvalds authored
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32: [AVR32] Use per-controller spi_board_info structures [AVR32] Warn, don't BUG if clk_disable is called too many times [AVR32] Make sure all genclocks have a parent [AVR32] Remove unnecessary sys_nfsservctl conditional [AVR32] Wire up the SysV IPC calls properly [AVR32] Define ioremap_nocache, ioport_map and ioport_unmap [AVR32] Fix prototypes for __raw_writesb and friends
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart: [AGPGART] allow drm populated agp memory types cleanups [AGPGART] intel-agp: Use ARRAY_SIZE macro when appropriate [AGPGART] Add agp-type-to-mask-type method missing from some drivers. [AGPGART] Don't try to remap i810 registers on resume. [AGPGART] Allow drm-populated agp memory types [AGPGART] compat ioctl
-
Linus Torvalds authored
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ] Longhaul - Redo Longhaul ver. 2 [CPUFREQ] EPS - Correct 2nd brand test [CPUFREQ] Longhaul - Separate frequency and voltage transition [CPUFREQ] Longhaul - Models of Nehemiah [CPUFREQ] Whitespace fixup [CPUFREQ] Longhaul - Simplier minmult [CPUFREQ] CPU_FREQ_TABLE shouldn't be a def_tristate [CPUFREQ] ondemand governor use new cpufreq rwsem locking in work callback [CPUFREQ] ondemand governor restructure the work callback [CPUFREQ] Rewrite lock in cpufreq to eliminate cpufreq/hotplug related issues [CPUFREQ] Remove hotplug cpu crap [CPUFREQ] Enhanced PowerSaver driver [CPUFREQ] Longhaul - Add VT8235 support [CPUFREQ] Longhaul - Fix guess_fsb function [CPUFREQ] Longhaul - Remove duplicate tables [CPUFREQ] Longhaul - Introduce Nehemiah C [CPUFREQ] fix cpuinfo_cur_freq for CPU_HW_PSTATE [CPUFREQ] Longhaul - Remove "ignore_latency" option
-
Ben Dooks authored
The current driver is not setting the dev field in the private data structure, which can lead to an OOPS if the driver tries to report an error. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Cc: James Simmons <jsimmons@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Thomas Hisch authored
Add format specifier %d for uid in ecryptfs_printk Signed-off-by:
Thomas Hisch <t.hisch@gmail.com> Cc: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by:
-
Michael Halcrow authored
eCryptfs is gobbling a lot of stack in ecryptfs_generate_key_packet_set() because it allocates a temporary memory-hungry ecryptfs_key_record struct. This patch introduces a new kmem_cache for that struct and converts ecryptfs_generate_key_packet_set() to use it. Signed-off-by:
Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by:
-
NeilBrown authored
When NFSD receives a write request, the data is typically in a number of 1448 byte segments and writev is used to collect them together. Unfortunately, generic_file_buffered_write passes these to the filesystem one at a time, so an e.g. 32K over-write becomes a series of partial-page writes to each page, causing the filesystem to have to pre-read those pages - wasted effort. generic_file_buffered_write handles one segment of the vector at a time as it has to pre-fault in each segment to avoid deadlocks. When writing from kernel-space (and nfsd does) this is not an issue, so generic_file_buffered_write does not need to break and iovec from nfsd into little pieces. This patch avoids the splitting when get_fs is KERNEL_DS as it is from NFSd. This issue was introduced by commit 6527c2bdAcked-by:
Nick Piggin <nickpiggin@yahoo.com.au> Cc: Norman Weathers <norman.r.weathers@conocophillips.com> Cc: Vladimir V. Saveliev <vs@namesys.com> Signed-off-by:
Neil Brown <neilb@suse.de> Signed-off-by:
-
J. Bruce Fields authored
When setting an ACL that lacks inheritable ACEs on a directory, we should set a default ACL of zero length, not a default ACL with all bits denied. Signed-off-by:
"J. Bruce Fields" <bfields@citi.umich.edu> Signed-off-by:
-
J. Bruce Fields authored
We're inserting deny's between some ACEs in order to enforce posix draft acl semantics which prevent permissions from accumulating across entries in an acl. That's fine, but we're doing that by inserting a deny after *every* allow, which is overkill. We shouldn't be adding them in places where they actually make no difference. Also replaced some helper functions for creating acl entries; I prefer just assigning directly to the struct fields--it takes a few more lines, but the field names provide some documentation that I think makes the result easier understand. Signed-off-by:
-
J. Bruce Fields authored
Return just the effective permissions, and forget about the mask. It isn't worth the complexity. WARNING: This breaks backwards compatibility with overly-picky nfsv4->posix acl translation, as may has been included in some patched versions of libacl. To our knowledge no such version was every distributed by anyone outside citi. Signed-off-by:
-
J. Bruce Fields authored
We should be returning ATTRNOTSUPP, not NOTSUPP, when acls are unsupported. Also fix a comment. Signed-off-by:
-
J. Bruce Fields authored
The wrong pointer is being kfree'd in savemem() when defer_free returns with an error. Signed-off-by:
Benny Halevy <bhalevy@panasas.com> Signed-off-by:
-
J. Bruce Fields authored
Simplify the memory management and code a bit by representing acls with an array instead of a linked list. Signed-off-by:
-
J. Bruce Fields authored
The code that splits an incoming nfsv4 ACL into inheritable and effective parts can be combined with the the code that translates each to a posix acl, resulting in simpler code that requires one less pass through the ACL. Signed-off-by:
-
J. Bruce Fields authored
The rfc allows us to be more permissive about the ACL inheritance bits we accept: "If the server supports a single "inherit ACE" flag that applies to both files and directories, the server may reject the request (i.e., requiring the client to set both the file and directory inheritance flags). The server may also accept the request and silently turn on the ACE4_DIRECTORY_INHERIT_ACE flag." Let's take the latter option--the ACL is a complex attribute that could be rejected for a wide variety of reasons, and the protocol gives us little ability to explain the reason for the rejection, so erroring out is a user-unfriendly last resort. Signed-off-by:
-
J. Bruce Fields authored
The server name is expected to be a null-terminated string, so we can't pass in the raw client identifier. What's more, the client identifier is just a binary, not necessarily printable, blob. Let's just use the ip address instead. The server name appears to exist just to help debugging by making some printk's more informative. Note that the string is copies into the rpc client structure, so the pointer to the local variable does not outlive the function call. Signed-off-by:
-
Jan Beulich authored
Use mask_ack_irq() where possible. Signed-off-by:
Jan Beulich <jbeulich@novell.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
Randy Dunlap authored
Fix kernel-doc warnings in IRQ management. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Ingo Molnar authored
Now that disable_irq() defaults to delayed-disable semantics, the IRQ_DISABLED flag is not needed anymore. Signed-off-by:
Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Ingo Molnar authored
Never mask interrupts immediately upon request. Disabling interrupts in high-performance codepaths is rare, and on the other hand this change could recover lost edges (or even other types of lost interrupts) by conservatively only masking interrupts after they happen. (NOTE: with this change the highlevel irq-disable code still soft-disables this IRQ line - and if such an interrupt happens then the IRQ flow handler keeps the IRQ masked.) Mark i8529A controllers as 'never loses an edge'. Signed-off-by:
-
Paul E. McKenney authored
Use RCU to avoid the need to acquire tasklist_lock in the single-threaded case of clock_gettime(). It still acquires tasklist_lock when for a (potentially multithreaded) process. This change allows realtime applications to frequently monitor CPU consumption of individual tasks, as requested (and now deployed) by some off-list users. This has been in Ingo Molnar's -rt patchset since late 2005 with no problems reported, and tests successfully on 2.6.20-rc6, so I believe that it is long-since ready for mainline adoption. [paulmck@linux.vnet.ibm.com: fix exit()/posix_cpu_clock_get() race spotted by Oleg] Signed-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
john stultz authored
Cleanup and re-enable vsyscall gettimeofday using the generic clocksource infrastructure. [akpm@osdl.org: cleanup] Signed-off-by:
John Stultz <johnstul@us.ibm.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@muc.de> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by:
-
john stultz authored
This patch converts x86_64 to use the GENERIC_TIME infrastructure and adds clocksource structures for both TSC and HPET (ACPI PM is shared w/ i386). [akpm@osdl.org: fix printk timestamps] [akpm@osdl.org: fix printk ckeanups] [akpm@osdl.org: hpet build fix] Signed-off-by:
-
john stultz authored
In preparation for the x86_64 generic time conversion, this patch splits out TSC and HPET related code from arch/x86_64/kernel/time.c into respective hpet.c and tsc.c files. [akpm@osdl.org: fix printk timestamps] [akpm@osdl.org: cleanup] Signed-off-by:
-
john stultz authored
In preparation for supporting generic timekeeping, this patch cleans up x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is also used in i386. This is necessary since the vxtime structure will be going away. Signed-off-by:
-
john stultz authored
Provides generic infrastructure for vsyscall-gtod. [akpm@osdl.org: cleanup] Signed-off-by:
-
Ingo Molnar authored
Add SysRq-Q to print pending timers and other timer info. Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by:
-
