Use SPI device pointer in the remaining two error and warning prints in
pxa2xx_spi_transfer_one() instead of platform device of the controller

It make prints in the function uniform and more useful especially the
error print here as it can reveal the driver that has mapped the DMA
itself and attempts to transfer more than the maximum supported DMA
transfer length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there
is no need to access it through the current SPI message pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Tegra SPI controller supports lsb first mode. Default is MSB bit first
and on selection of SPI_LSB_FIRST through SPI mode transmission happens
with LSB bit first.

This patch adds SPI_LSB_FIRST flag to mode_bits and also configures it
on request.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: Use packed mode for 32 bits per word transfers to increase
performance as each packet is a full 32-bit word.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The comment says that we should not allow changes (to
bits_per_word/speed_hz) while CS is active, and indeed the code below
does fsl_spi_setup_transfer() when the ->cs_change of the previous
spi_transfer was set (and for the very first transfer).

So the sanity checking is a bit too strict - we can change it to
follow the same logic as is used by the actual transfer loop.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

__spi_validate() in the generic SPI code sets ->speed_hz and
->bits_per_word to non-zero values, so this condition is always true.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds the dma support for the stm32-qspi hardware.
The memory buffer constraints (lowmem, vmalloc, kmap) are taken into
account by framework. In read mode, the memory map is preferred vs
dma (due to better throughput). If the dma transfer fails the buffer
is sent by polling.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch adds spi_master_put in release function
to drop the controller's refcount.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.

This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).

This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This checking is already done in __spi_validate_bits_per_word().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix sparse warning:

drivers/spi/atmel-quadspi.c:369:12: warning:
 symbol 'atmel_qspi_get_name' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The newly added tracepoints in the spi-mxs driver cause a link
error when the driver is a loadable module:

ERROR: "__tracepoint_spi_transfer_stop" [drivers/spi/spi-mxs.ko] undefined!
ERROR: "__tracepoint_spi_transfer_start" [drivers/spi/spi-mxs.ko] undefined!

I'm not quite sure where to put the export statements, but
directly after the inclusion of the header seems as good as
any other place.

Fixes: f3fdea3a ("spi: mxs: add tracing to custom .transfer_one_message callback")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

It's useful during debug to see what DMA burst size is.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some masters may have different DMA burst size than hard coded default.
In such case respect the value given by DMA burst size provided via
platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Synopsys SSI Controller has an interface clock, but most SoCs hide
this away. However, on some SoCs you need to explicitly enable the
interface clock in order to access the registers. Therefore, add support
for an optional interface clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add documentation to the Synopsys SPI dt-bindings to support an
optional interface clock that may be used for register access.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Synopsys SSI driver uses a mandatory clock that is not documented,
so detail it in the device tree bindings. Also correct the spelling of
"pins" in the "Optional Properties" section for the driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 2e541b64 ("spi: spi-mem: stm32-qspi: add suspend/resume support")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.1-rc1

There is nothing in the driver which requires OF specific header
to be included.

Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fixes: 944c01a8 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The MPC8309 has a dedicated signal, SPISEL_BOOT, usually used as chip
select for the flash device from which the bootloader is loaded. It is
not an ordinary gpio, but is simply controlled via the SPI_CS register
in the system configuration.

To allow accessing such a spi slave, we need to teach
fsl_spi_cs_control() how to control the SPISEL_BOOT signal. To
distinguish the gpio-controlled slaves, continue to have those use
chip_select values of 0..ngpios-1, and use chip_select == ngpios for
the boot flash.

I'm not too happy with all the ifdeffery, but it seems to be necessary
for guarding the sysdev/fsl_soc.h and use of
get_immrbase() (spi-fsl-lib.c already contains similar ifdeffery).

Googling suggests that the MPC8306 is similar, with the SPI_CS
register at the same offset.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>

Commit b7bb367a added support for inserting delays in between
individual words within a single SPI transaction. This makes it
accessible from userspace.

WARNING: This delay is silently ignored unless the SPI controller
implements extra support for it. This is similar to how the in-kernel
users handle the other existing property, spi_transfer->word_delay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>

Delete the extra space.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The spi_transfer *t will be used in one transfer whatever. If t is NULL,
there has no need to try sending data, so add an error return here.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add dma mode support for LPSPI. Any frame longer than half txfifosize will
be sent by dma mode.

For now, there are some limits:
1. The maximum transfer speed in master mode depends on the slave device,
   at least 40MHz(tested by spi-nor on 8qm-lpddr4-arm2 base board);
2. The maximum transfer speed in slave mode is 15MHz(imx7ulp),
   22MHz(8qm/qxp). In order to reach the maximum speed which is mentioned
   in datasheet, the load of connect wires between master and slave
   should be less than 15pF.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the default implementation of transfer_one_msg/chipselect/setup
functions in spi core to implement cs-gpio control.
Use fsl_lpspi_prepare_message to init the cs_gpio pin.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add a error info when set a speed which greater than half of per-clk of
spi module.

The minimum SCK period is 2 cycles(CCR[SCKDIV]). So the maximum transfer
speed is half of spi per-clk.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Enable the runtime power management for lpspi module.

Do some adaptation work from kernel 4.9 to 4.14.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add introductions of clocks and clock-names strings.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add both ipg and per clock for lpspi to support i.MX8QM/QXP boards.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Pull more Kbuild updates from Masahiro Yamada:

 - add more Build-Depends to Debian source package

 - prefix header search paths with $(srctree)/

 - make modpost show verbose section mismatch warnings

 - avoid hard-coded CROSS_COMPILE for h8300

 - fix regression for Debian make-kpkg command

 - add semantic patch to detect missing put_device()

 - fix some warnings of 'make deb-pkg'

 - optimize NOSTDINC_FLAGS evaluation

 - add warnings about redundant generic-y

 - clean up Makefiles and scripts

* tag 'kbuild-v5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: remove stale lxdialog/.gitignore
  kbuild: force all architectures except um to include mandatory-y
  kbuild: warn redundant generic-y
  Revert "modsign: Abort modules_install when signing fails"
  kbuild: Make NOSTDINC_FLAGS a simply expanded variable
  kbuild: deb-pkg: avoid implicit effects
  coccinelle: semantic code search for missing put_device()
  kbuild: pkg: grep include/config/auto.conf instead of $KCONFIG_CONFIG
  kbuild: deb-pkg: introduce is_enabled and if_enabled_echo to builddeb
  kbuild: deb-pkg: add CONFIG_ prefix to kernel config options
  kbuild: add workaround for Debian make-kpkg
  kbuild: source include/config/auto.conf instead of ${KCONFIG_CONFIG}
  unicore32: simplify linker script generation for decompressor
  h8300: use cc-cross-prefix instead of hardcoding h8300-unknown-linux-
  kbuild: move archive command to scripts/Makefile.lib
  modpost: always show verbose warning for section mismatch
  ia64: prefix header search path with $(srctree)/
  libfdt: prefix header search paths with $(srctree)/
  deb-pkg: generate correct build dependencies

Pull x86 asm updates from Thomas Gleixner:
 "Two cleanup patches removing dead conditionals and unused code"

* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/asm: Remove unused __constant_c_x_memset() macro and inlines
  x86/asm: Remove dead __GNUC__ conditionals

Pull perf fixes from Thomas Gleixner:
 "Three fixes for the fallout from the TSX errata workaround:

   - Prevent memory corruption caused by a unchecked out of bound array
     index.

   - Two trivial fixes to address compiler warnings"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Make dev_attr_allow_tsx_force_abort static
  perf/x86: Fixup typo in stub functions
  perf/x86/intel: Fix memory corruption

Pull xen fix from Juergen Gross:
 "A fix for a Xen bug introduced by David's series for excluding
  ballooned pages in vmcores"

* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: Fix mapping PG_offline pages to user space

Pull 9p updates from Dominique Martinet:
 "Here is a 9p update for 5.1; there honestly hasn't been much.

  Two fixes (leak on invalid mount argument and possible deadlock on
  i_size update on 32bit smp) and a fall-through warning cleanup"

* tag '9p-for-5.1' of git://github.com/martinetd/linux:
  9p/net: fix memory leak in p9_client_create
  9p: use inode->i_lock to protect i_size_write() under 32-bit
  9p: mark expected switch fall-through

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: kbuild-all@01.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190313184243.GA10820@lkp-sb-ep06