Implement SDR driver for Realtek RTL2832U chip as a DVB extension
module. SDR module is attached by DVB USB RTL28XXU driver as a DVB
SEC (satellite equipment controller) module. Abusing unused SEC here
has no harm as that is DVB-T only frontend.

SDR functionality is provided by RTL2832 DVB-T demodulator. I suspect
it is originally planned for DAB and FM, but it could be abused general
SDR, due to modern silicon tuners that has wide frequency range and a
lot of configurable parameters (filters, gains, ...).

http://thread.gmane.org/gmane.linux.drivers.video-input-infrastructure/44461Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Implement PLL lock control to get PLL lock flag status from tuner
synthesizer.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

There was 32-bit overflow on VCO frequency calculation which blocks
tuning to 1073 - 1104 MHz. Use 64 bit number in order to avoid VCO
frequency overflow.

After that fix device in question tunes to following range:
60 - 1104 MHz
1250 - 2207 MHz
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Implement gain and bandwidth controls using v4l2 control framework.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Driver conversion from proprietary DVB tuner model to more
general I2C driver model.

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

rc_map_get() takes a single string literal for the module to load,
so make sure it cannot be used as a format string in the call to
request_module().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The sizeimage is that of a single field, not that of a full frame.
That makes no sense, and in fact all drivers supporting ALTERNATE will
set sizeimage to that of a field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Be more specific as to who has to fill in each field/flag: the driver
or the application.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The code said for (i = 0; i > 30; ++i) instead of i < 30.

Fix this and clean it up a bit at the same time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Rename v4l2_format_sdr to v4l2_sdr_format in order to keep it in
line with other formats.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix msi3101 driver v4l2-compliance issues.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix msi001 driver v4l2-compliance issues.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

That value is coming from the user and we need only ensure it is
reasonable. That was pointed by Hans when reviewing rtl2832_sdr driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Mirics MSi2500 (MSi3101) SDR ADC + USB interface driver. Currently
in staging as SDR API is not ready.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Mirics MSi001 silicon tuner driver. Currently in staging as SDR API
is not ready.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Remove MSi001 RF tuner related code as MSi001 functionality is moved
to own driver.

Implement SPI master adapter.

Attach MSi001 driver via SPI / V4L subdev framework.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

That RF tuner driver is bound via SPI bus model and it implements V4L
subdev API. I split it out from MSi3101 SDR driver.
MSi3101 = MSi2500 + MSi001.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Massive rewrite. Use SDR API. Fix bugs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add volatile boolean control to indicate if tuner frequency synthesizer
is locked to requested frequency. That means tuner is able to receive
given frequency. Control is named as "PLL lock", since frequency
synthesizers are based of phase-locked-loop. Maybe more general name
could be wise still?

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Document PLL lock V4L2 control. It is read only RF tuner control
which is used to inform if tuner is receiving frequency or not.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add VIDIOC_ENUM_FREQ_BANDS, enumerate supported frequency bands,
IOCTL support for sub-device tuners too.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

V4L2_SDR_FMT_CU8 — Complex unsigned 8-bit IQ sample
V4L2_SDR_FMT_CU16LE — Complex unsigned 16-bit little endian IQ sample

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Document V4L2_SDR_FMT_CU16LE format.
It is complex unsigned 16-bit little endian IQ sample. Used by
software defined radio devices.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Document V4L2_SDR_FMT_CU8 SDR format.
It is complex unsigned 8-bit IQ sample. Used by software defined
radio devices.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add some info what is RF tuner in context of V4L RF tuner class.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It appears that controls are ordered by ID number when enumerating.
That could lead illogical UI as controls are usually enumerated and
drawn by the application at runtime.

Change order of controls by reorganizing assigned IDs now as we can.
It is not reasonable possible after the API is released. Also, leave
some spare space between IDs too for possible future extensions.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Modern silicon RF tuners has one or more adjustable filters on
signal path, in order to filter noise from desired radio channel.

Add channel bandwidth control to tell the driver which is radio
channel width we want receive. Filters could be then adjusted by
the driver or hardware, using RF frequency and channel bandwidth
as a base of filter calculations.

On automatic mode (normal mode), bandwidth is calculated from sampling
rate or tuning info got from userspace. That new control gives
possibility to set manual mode and let user have more control for
filters.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Use Hertz as a unit for radio channel bandwidth.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Add documentation for RF tuner bandwidth controls. These controls are
used to set filters on tuner signal path.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Fix spelling typo under Documentation/DocBook/media.
It is because these files are NOT generated by "make htmldocs",
I have to fix the files.

[m.chehab@samsung.com: fix a merge conflict]
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

0458:707f KYE Systems Corp. (Mouse Systems) TVGo DVB-T03 [RTL2832]

The USB dongle uses RTL2832U demodulator and FC0012 tuner.
Signed-off-by: Jan Vcelak <jv@fcelda.cz>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

The "Renesas Corporation" listed in the copyright notice doesn't exist.
Replace it with "Renesas Electronics Corporation" and update the
copyright years.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Check if index is within bounds _before_ accessing the value.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.

Currently that case is not possible as only used tuner has this callback.

Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Coverity CID 1166051: Logically dead code (DEADCODE)

TS clock calculation could be more accurate, but as it is not,
remove those unused clock speeds.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Coverity CID 1166050: Dead default in switch (DEADCODE)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

While playing with make coccicheck I noticed this message:
drivers/media/rc/rc-main.c:1245:3-9: preceding lock on line 1238

It was introduced by commit 587d1b06 ([media] rc-core: reuse device
numbers) which returns -ENOMEM after a mutex_lock without first
unlocking it when there are no more device numbers left. The added code
doesn't depend on the device lock, so move it before the lock is taken.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

Static checkers complain about the inconsistent NULL check here.

There is an unchecked dereference of "input->fe" in the call to
tuner_attach_tda18271() and there is a second unchecked dereference a
couple lines later when we do:
	input->fe2->tuner_priv = input->fe->tuner_priv;

But actually "intput->fe" can't be NULL because if demod_attach_drxk()
fails to allocate it, then we would have return an error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>

ARRAY_SIZE(buf) (8 elements) was intended instead of sizeof(buf) (16
bytes).  But this is just a sanity check and the callers always pass
valid values so this doesn't cause a problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>