- 22 Sep, 2022 1 commit
-
-
Wen Gong authored
Currently commit 1f682dc9 ("ath11k: reduce the wait time of 11d scan and hw scan while add interface") introduced a wait_for_completion_timeout operation for ar->scan.completed, another one is existed in ath11k_scan_stop(), then ath11k has two places to wait for the ar->scan.completed and they run in different thread, thus it is possible to happend that the two thread both enter wait status. To handle this scenario, ath11k should change the complete() to complete_all() for the ar->scan.completed. This also work well when it is only one thread wait for ar->scan.completed. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220919024413.25083-1-quic_wgong@quicinc.com
-
- 19 Sep, 2022 5 commits
-
-
Manikanta Pubbisetty authored
Add support for WoW on WCN6750 chipset. Unlike other chips where WoW exit happens after sending WoW wakeup WMI command, exit from WoW suspend in the case of WCN6750 happens upon sending a WoW exit SMP2P (Shared memory point to point) message to the firmware. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
-
Manikanta Pubbisetty authored
Add required bindings to support WoW (Wake on Wireless) on WCN6750 which is based on ath11k driver. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Baochen Qiang authored
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only when ARP method is used, this causes firmware always to crash when wowlan is enabled because firmware needs it to be present no matter ARP method is used or not. Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by default. Also fix below typo: s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/ Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Fixes: 0f84a156 ("ath11k: Handle keepalive during WoWLAN suspend and resume") Signed-off-by:
Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
-
Jilin Yuan authored
Delete the redundant word 'that'. Signed-off-by:
Jilin Yuan <yuanjilin@cdjrlc.com> Signed-off-by:
-
Bryan O'Donoghue authored
The signal-to-noise-ratio SNR is returned by the wcn36xx firmware for each received frame. SNR represents all of the unwanted interference signal after filtering out the fundamental frequency and harmonics of the frequency. Noise can come from various electromagnetic sources, from temperature affecting the performance hardware components or quantization effects converting from analog to digital domains. The SNR value returned by the WiFi firmware then is a good source of entropy. Other WiFi drivers offer up the noise component of the FFT as an entropy source for the random pool e.g. commit 2aa56cca ("ath9k: Mix the received FFT bins to the random pool") I attended Jason's talk on sources of randomness at Plumbers and it occurred to me that SNR is a reasonable candidate to add. Cc: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
- 16 Sep, 2022 3 commits
-
-
Jeff Johnson authored
Fix documentation issues reported by kernel-doc: - Incorrect use of /** for non-kernel-doc comments - Mismatch between documented and actual identifiers - Incorrect identifier syntax Signed-off-by:
Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by:
-
Jeff Johnson authored
Fix misspellings flagged by 'codespell'. Signed-off-by:
-
Jeff Johnson authored
Fix misspellings flagged by 'codespell'. Signed-off-by:
-
- 10 Sep, 2022 6 commits
-
-
Manikanta Pubbisetty authored
Increase TCL data ring size to 2048 for WCN6750. This is needed to meet 160 MHz TX throughput. Add a new hw_param to indicate the TX ring size for individual devices. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
Manikanta Pubbisetty authored
Currently in the case of WCN6750, only one TCL ring is used for TX, this is limiting the TX throughput in 160 MHz case, enabling multiple TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in the case of TCP TX, therefore add the support of multi TX ring for WCN6750. Currently TCL ring is selected based on CPU ID, this logic cannot be applied for WCN6750 as there is chance of out of order TX of packets and to avoid this, choose TCL ring based on flow hash so that packets of the same flow will end up on same TCL ring. For the same reason, TCL ring retry logic is also not applicable for WCN6750. Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from existing devices. Create a new TCM/WBM/RBM mapping for WCN6750. Change does not impact existing ath11k devices. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
Manikanta Pubbisetty authored
Enable threaded NAPI on all ath11k targets. Unlike traditional NAPI poll which runs in softirq context and on the core which scheduled the NAPI, threaded NAPI makes use of kernel threads which are under direct control of the scheduler and helps in balancing the NAPI processing load across multiple CPUs thereby improving throughput. In the case of WCN6750, enabling threaded NAPI has improved 160 MHz RX throughput by nearly 400 Mbps. Similar gains can be expected on other ath11k devices as well. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
Jianglei Nie authored
mhi_alloc_controller() allocates a memory space for mhi_ctrl. When gets some error, mhi_ctrl should be freed with mhi_free_controller(). But when ath11k_mhi_read_addr_from_dt() fails, the function returns without calling mhi_free_controller(), which will lead to a memory leak. We can fix it by calling mhi_free_controller() when ath11k_mhi_read_addr_from_dt() fails. Signed-off-by:
Jianglei Nie <niejianglei2021@163.com> Reviewed-by:
-
Baochen Qiang authored
On-board SRAM contains valuable information for firmware debugging so add a new file named "sram" to debugfs with which we can dump SRAM content using following the following: cp /sys/kernel/debug/ath11k/wcn6855\ hw2.0/sram /tmp/sram Currently this feature is enabled for QCA6390 and WCN6855. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
Baochen Qiang authored
ath11k_pcic_write32/read32 tries to do wake up before doing actual write/read work, which means each time a u32 is written/read, wake up is performed. This is not necessary in case where we do a large amount of write/read, because only one time of wake up is needed. So split each one into two parts, the first part does wake up and release, and the second one does actual write/read work. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
-
- 07 Sep, 2022 1 commit
-
-
Manikanta Pubbisetty authored
Enable remain on channel support on WCN6750 as it is needed for GAS, Passpoint. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
- 02 Sep, 2022 3 commits
-
-
Manikanta Pubbisetty authored
Add support to connect to a non-transmit MBSSID AP profile. Non-transmit MBSSID profile parameters are passed to the firmware via WMI VDEV UP command and this helps firmware to track MBSSID profile within the multi-BSS beacon and report beacon loss if any. WCN6750, QCA6390 & WCN6855 firmwares have the support and hence enable the support on these hardwares. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
Manikanta Pubbisetty authored
Currently, creation of debugfs entries for TWT is failing during hardware restart because of the residual TWT files which were created during add_interface(). Since, struct arvif{} is memset to zero upon add_interface() invocation, when the hardware restart is triggered, arvif is memset to 0 and TWT files are attempted to create again which will fail because of the residual TWT files already in place, this leads to hardware restart failure. Also, it is not a good idea to return error from add_interface() because of debugfs file creation failures. Moreover, debugfs framework can very well handle the errors in it's create file & remove file APIs and the errors returned by these APIs are not checked in most usecases. Fix the HW restart failure by ignoring the errors returned from the debugfs APIs. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Fixes: fe98a613 ("ath11k: add debugfs for TWT debug calls") Signed-off-by: -
Manikanta Pubbisetty authored
Currently TWT debugfs files required for manually testing the TWT feature are created only for the AP interfaces; these debugfs hooks are also required for the station interfaces in order to test the TWT feature manually, therefore create these debugfs hooks for station iftype as well. In the case of station interfaces, TWT is entirely handled in the firmware based on input parameters passed to it during association via TWT enable WMI command. In order to manually test this feature, firmware expects to first disable the TWT feature and then send the enable command with sta_cong_timer_ms parameter set to 0. This is true for WCN6750, QCA6390 & WCN6855 hardwares. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
- 01 Sep, 2022 3 commits
-
-
Manikanta Pubbisetty authored
Add cold boot calibration support on WCN6750. Unlike other chipsets where firmware(FW) is restarted after cold boot calibration is completed, it is recommended not to restart the firmware for WCN6750. For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication to the driver after cold boot calibration is completed. QMI message flow for WCN6750 with cold boot support: FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host -> FW_READY to Host -> MODE_ON to FW QMI message flow for other chipsets with cold boot support: FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host -> Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW QMI message flow for chipsets without cold boot support: FW_INIT_DONE to Host -> MODE_ON to FW Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
Manikanta Pubbisetty authored
QMI message IDs for some of the QMI messages were incorrectly defined in the original implementation. These have to be corrected to enable cold boot support on WCN6750. These corrections are applicable for all chipsets and will not impact them. Refactor the code accordingly. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by:
-
Manikanta Pubbisetty authored
When the system shuts down, SMMU driver will be stopped and will not assist in IOVA translations. SMMU driver expects all of its consumers to shutdown before shutting down itself. WCN6750 being one of the consumer device should not perform any DMA operations after the SMMU has shutdown which will otherwise result in SMMU faults. SMMU driver will call the shutdown() callback of all its consumer devices and the consumers shall stop further DMA activity after the invocation of their respective shutdown() callbacks. Register the shutdown() callback to the platform core for WCN6750. Change will not impact other AHB ath11k devices. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
-
- 30 Aug, 2022 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v6.1. Only fixes this time.
-
Tetsuo Handa authored
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with pkt_len = 0 but ath9k_hif_usb_rx_stream() uses __dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb with uninitialized memory and ath9k_htc_rx_msg() is reading from uninitialized memory. Since bytes accessed by ath9k_htc_rx_msg() is not known until ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in ath9k_hif_usb_rx_stream(). We have two choices. One is to workaround by adding __GFP_ZERO so that ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose the latter. Note that I'm not sure threshold condition is correct, for I can't find details on possible packet length used by this protocol. Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1] Reported-by:syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
- 29 Aug, 2022 1 commit
-
-
Sun Ke authored
Add the missing unlock before return in the error handling case. Fixes: ccdde7c7 ("wifi: mac80211: properly implement MLO key handling") Signed-off-by:
Sun Ke <sunke32@huawei.com> Link: https://lore.kernel.org/r/20220827022452.823381-1-sunke32@huawei.comSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
- 26 Aug, 2022 15 commits
-
-
David S. Miller authored
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Johannes berg says: ==================== Various updates: * rtw88: operation, locking, warning, and code style fixes * rtw89: small updates * cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work * brcmfmac: a couple of fixes * misc cleanups etc. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jean-Francois Le Fillatre authored
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as a broken CDC device by default. Add the custom Lenovo PID to the r8152 driver to support it properly. Also, systems compatible with this dock provide a BIOS option to enable MAC address passthrough (as per Lenovo document "ThinkPad Docking Solutions 2017"). Add the custom PID to the MAC passthrough list too. Tested on a ThinkPad 13 1st gen with the expected results: passthrough disabled: Invalid header when reading pass-thru MAC addr passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX Signed-off-by:
Jean-Francois Le Fillatre <jflf_kernel@gmx.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-08-24 (ice) This series contains updates to ice driver only. Marcin adds support for TC parsing on TTL and ToS fields. Anatolli adds support for devlink port split command to allow configuration of various port configurations. Jake allows for passing and writing an additional NVM write activate field by expanding current cmd_flag. Ani makes PHY debug output more readable. ==================== Signed-off-by: -
Ping-Ke Shih authored
clang reports uninitialized use: >> drivers/net/wireless/realtek/rtw88/main.c:731:2: warning: variable 'primary_channel_idx' is used uninitialized whenever switch default is taken [-Wsometimes-uninitialized] default: ^~~~~~~ drivers/net/wireless/realtek/rtw88/main.c:754:39: note: uninitialized use occurs here hal->current_primary_channel_index = primary_channel_idx; ^~~~~~~~~~~~~~~~~~~ drivers/net/wireless/realtek/rtw88/main.c:687:24: note: initialize the variable 'primary_channel_idx' to silence this warning u8 primary_channel_idx; ^ = '\0' This situation could not happen, because possible channel bandwidth 20/40/80MHz are enumerated. Fixes: 341dd1f7 ("wifi: rtw88: add the update channel flow to support setting by parameters") Reported-by:kernel test robot <lkp@intel.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Reviewed-by:
Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20220815062004.22920-1-pkshih@realtek.comSigned-off-by:
-
Qingfang DENG authored
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an optional in-band status feature where the PHY's link status, speed and duplex mode can be passed to the MAC. Allow RGMII/RTBI to use in-band status. Signed-off-by:
Qingfang DENG <dqfext@gmail.com> Signed-off-by:
-
David S. Miller authored
Maksym Glubokiy says: ==================== net: prestera: matchall features This patch series extracts matchall rules management out of SPAN API implementation and adds 2 features on top of that: - support for egress traffic (mirred egress action) - proper rule priorities management between matchall and flower ==================== Signed-off-by: -
Maksym Glubokiy authored
matchall rules can be added only to chain 0 and their priorities have limitations: - new matchall ingress rule's priority must be higher (lower value) than any existing flower rule; - new matchall egress rule's priority must be lower (higher value) than any existing flower rule. The opposite works for flower rule adding: - new flower ingress rule's priority must be lower (higher value) than any existing matchall rule; - new flower egress rule's priority must be higher (lower value) than any existing matchall rule. This is a hardware limitation and thus must be properly handled in driver by reporting errors to the user when newly added rule has such a priority that cannot be installed into the hardware. To achieve this, the driver must maintain both min/max matchall priorities for every flower block when user adds/deletes a matchall rule, as well as both min/max flower priorities for chain 0 for every adding/deletion of flower rules for chain 0. Cc: Serhiy Boiko <serhiy.boiko@plvision.eu> Signed-off-by:
Maksym Glubokiy <maksym.glubokiy@plvision.eu> Signed-off-by:
-
Serhiy Boiko authored
This enables adding matchall rules for egress: tc filter add .. egress .. matchall skip_sw \ action mirred egress mirror dev .. Signed-off-by:Serhiy Boiko <serhiy.boiko@plvision.eu> Signed-off-by:
-
Serhiy Boiko authored
This commit adds more clarity to handling of TC_CLSMATCHALL_REPLACE and TC_CLSMATCHALL_DESTROY events by calling newly added *_mall_*() handlers instead of directly calling SPAN API. This also extracts matchall rules management out of SPAN API since SPAN is a hardware module which is used to implement 'matchall egress mirred' action only. Signed-off-by:
Taras Chornyi <tchornyi@marvell.com> Signed-off-by:
-
Oleksij Rempel authored
Add phylink based ethtool pause configuration Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Oleksij Rempel authored
There are some exotic ax88772 based devices which may require functionality provide by the phylink framework. For example: - US100A20SFP, USB 2.0 auf LWL Converter with SFP Cage - AX88772B USB to 100Base-TX Ethernet (with RMII) demo board, where it is possible to switch between internal PHY and external RMII based connection. So, convert this driver to phylink as soon as possible. Tested with: - AX88772A + internal PHY - AX88772B + external DP83TD510E T1L PHY Signed-off-by:
-
Xin Gao authored
The full 'unsigned int' is better than 'unsigned'. Signed-off-by:
Xin Gao <gaoxin@cdjrlc.com> Link: https://lore.kernel.org/r/20220816181040.9044-1-gaoxin@cdjrlc.com [fix indentation] Signed-off-by:
-
Wolfram Sang authored
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Ryder Lee authored
Driver may update sinfo directly through .sta_statistics, so this patch makes sure that ethool gets the correct statistics. Signed-off-by:
Ryder Lee <ryder.lee@mediatek.com> Link: https://lore.kernel.org/r/f9edff14dd7f5205acf1c21bae8e9d8f9802dd88.1661466499.git.ryder.lee@mediatek.comSigned-off-by:
-
Johannes Berg authored
If we add 6 GHz capability in MLO, we cannot use the SMPS mode from the deflink. Pass it separately instead since on a second link we don't even have a link data struct yet. Signed-off-by:
-
