Currently the shdma dmaengine driver uses runtime PM to save power, when
no channel on the specific controller is requested by a user. This patch
switches the driver to count individual DMA transfers. That way the
controller can be powered down between transfers, even if some of its
channels are in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>

The IRQ handler of the shdma driver accesses common hardware registers,
that are also accessed from other contexts. Therefore access to them
has to be performed with interrupts disabled, not only with disabled
bottom halves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>

Add missing include of linux/module.h to fix build error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

dma_async_device_register will re-init chan_id and chancnt,
so whatever chan_id and chancnt are set in drivers, they will
be re-written by dma_async_device_register.

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

In pl08x_free_txd(), check if pool is allocated successfully before freeing it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Untill now, sg_len greater than one is not supported. This patch adds support to
do that.

Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

On some sh-mobile systems there are more than one DMA controllers, that
can be used for serial ports. Specifying a DMA device in sh-sci platform
data unnecessarily restricts the driver to only use one DMA controller.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[Fixed the trivial conflict in include/linux/serial_sci.h]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch removes the samsung specific enum type 's3c2410_dmasrc'
and uses 'dma_data_direction' instead.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds to support the DMA PL330 driver that uses
DMA generic API. Samsung sound driver uses DMA generic API
if architecture supports it. Otherwise, use samsung specific
S3C-PL330 API driver to transfer PCM data.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: removed useless variable]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch modifies to merge the dma control code. Original
s3c64xx spi driver has each dma control code for rx and tx
channel. This patch merges these dma control codes into one.
With this patch, a dma setup function and callback function
handle for both rx and tx channel.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds to support DMA generic API to transfer raw
SPI data. Basiclly the spi driver uses DMA generic API if
architecture supports it. Otherwise, uses Samsung specific
S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Since DMA generic APIs can be used for Samsung DMA now so that
the s3c-pl330 which includes Samsung specific DMA APIs can be
removed.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch makes Samsung S5P64X0 to use DMA PL330 driver
on DMADEVICE. The S5P64X0 uses DMA generic APIs instead of
SAMSUNG specific S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch makes Samsung S5PC100 to use DMA PL330 driver
on DMADEVICE. The S5PC100 uses DMA generic APIs instead of
SAMSUNG specific S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch makes Samsung S5PV210 to use DMA PL330 driver
on DMADEVICE. The S5PV210 uses DMA generic APIs instead of
SAMSUNG specific S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch makes Samsung EXYNOS4 to use DMA PL330 driver
on DMADEVICE. The EXYNOS4 uses DMA generic APIs instead of
SAMSUNG specific S3C-PL330 APIs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds common DMA operations which are used for Samsung DMA
drivers. Currently there are two types of DMA driver for Samsung SoCs.
The one is S3C-DMA for S3C SoCs and the other is PL330-DMA for S5P SoCs.
This patch provides funcion pointers for common DMA operations to DMA
client driver like SPI and Audio. It makes DMA client drivers support
multi-platform.
In addition, this common DMA operations implement the shared actions
that are needed for DMA client driver. For example shared actions are
filter() function for dma_request_channel() and parameter passing for
device_prep_slave_sg().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds to support PL330-DMA driver on DMADEVICE for S5P SoCs.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds DMA_CYCLIC capability that is used for audio driver.
DMA driver activated with it reuses the dma requests that were submitted
through tx_submit().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Original code carries out the start operation after flush operation.
But start operation is not required for DMA_TERMINATE_ALL command.
So, this patch removes the unnecessary start operation and only carries out
the flush operation for handling DMA_TERMINATE_ALL command.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[Fixed typos in changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch updates following 3 items.
1. Removes unneccessary code.
2. Add AMBA, PL330 configuration
3. Change the meaning of 'peri_id' variable
   from PL330 event number to specific dma id by user.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Before converting the dma channel to our private data structure, first
check that the channel is indeed one which our driver registered.  We
do this by ensuring that the underlying device is bound to our driver.

This avoids potential oopses if we try to reference 'plchan->name'
against a foreign drivers dma channel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().

Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0    Not tainted  (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

d40_desc_free() already calls d40_pool_lli_free().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Fixed trivial conflicts  in  drivers/dma/amba-pl08x.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The firmware blob may not be available when the driver
probes. Instead of blocking the whole kernel use
request_firmware_nowait() and continue without firmware.
The ROM scripts can already be used then if available.
For the devicetree case the ROM scripts are not available,
still the probe function should not block. The driver
will be unusable in this case, but we have no way of
detecting this properly. The configuration of the dma
channels will fail, so nothing bad should happen.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

If we do not have a firmare script for a given transfer,
the setup of this channel must fail. For this the script
addresses have to be < 0 initially, not 0.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

channel0 of the sdma engine is the configuration channel. It
is a shared resource and thus must be protected by a mutex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Making dmatest threads freezable allows its use for system PM testing.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
  OMAP: omap_device: only override _noirq methods, not normal suspend/resume
  PM / Runtime: Correct documentation of pm_runtime_irq_safe()
  ARM: mach-shmobile: sh7372 LCDC1 suspend fix
  sh-sci / PM: Use power.irq_safe
  PM: Use spinlock instead of mutex in clock management functions

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: sbp2: fix panic after rmmod with slow targets

This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
 - Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
  i915: do not setup intel_backlight twice