A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.

If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.

Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps

Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The flow control workaround for ASM1042A xHC hosts sleeps between
register polling. The workaround gets called in several places, among
them with spin_lock_irq() held when xHC host is resumed or hoplug removed.

This was noticed as kernel panics at resume on a Dell XPS15 9550 with
TB16 thunderbolt dock.

Avoid sleeping with spin_lock_irq() held, use udelay() instead

The original workaround was added to 4.9 and 4.12 stable releases,
this patch needs to be applied to those as well.

Fixes: 9da5a109 ("xhci: Bad Ethernet performance plugged in ASM1042A host")
Cc: <stable@vger.kernel.org> #4.9+
Reported-by: Jose Marino <marinoj@nso.edu>
Tested-by: Jose Marino <marinoj@nso.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 4c39d4b9 ("usb: xhci: use bus->sysdev for DMA configuration")
updated the method determining DMA for XHCI from sysdev. However, this
patch broke the ability to enumerate the FWNODE from parent ACPI devices
from the child plat XHCI device.

Currently, xhci_plat is not set up properly when the parent device is an
ACPI node. The conditions that xhci_plat_probe should satisfy are

1. xhci_plat comes from firmware
2. xhci_plat is child of a device from firmware (dwc3-plat)
3. xhci_plat is grandchild of a pci device (dwc3-pci)

Case 2 is covered when the child is an OF node (by checking
sysdev->parent->of_node), however, an ACPI parent will return NULL in
the of_node check and will thus not result in sysdev being set to
sysdev->parent

[   17.591549] xhci-hcd: probe of xhci-hcd.6.auto failed with error -5

This change adds a check for ACPI to completely allow for condition 2.
This is done by first checking if the parent node is of type ACPI (e.g.,
dwc3-plat) and set sysdev to sysdev->parent if either of the two
following conditions are met:

1: If fwnode is empty (in the case that platform_device_add_properties
was not called on the allocated platform device)
2: fwnode exists but is not of type ACPI (this would happen if
platform_device_add_properties was called on the allocated device.
Instead of type FWNODE_ACPI, you would end up with FWNODE_PDATA)

Cc: stable@vger.kernel.org #4.12.x
Cc: stable@vger.kernel.org #4.13.x

Fixes: 4c39d4b9 ("usb: xhci: use bus->sysdev for DMA configuration")
Tested-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Read the endpiont ESIT from endpiont context using correct macro.
Add a macro for reading the high bits of ESIT for Large ESIT Payload
Capable hosts (LEC=1)

Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.

The wrong units were also corrected in a second handshake call.

Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Dickerson <jim.dickerson@hpe.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)

The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.

This caused null pointer dereference errors in bus_resume function.

Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the xhci_add_endpoint(), a new ring was allocated and saved at
xhci_virt_ep->new_ring. Hence, when error happens, we need to free
the allocated ring before returning error.

Current code frees xhci_virt_ep->ring instead of the new_ring. This
patch fixes this.

Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit e0429362
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.

The workaround is introducing delay for some USB operations.

According to our testing, delay introduced by original commit
is not long enough and in rare cases we still see issues described
by the aforementioned commit.

This patch increases delays introduced by original commit.
Having this patch applied we do not see those problems anymore.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uwbd_start() calls kthread_run() and checks that the return value is
not NULL. But the return value is not NULL in case kthread_run() fails,
it takes the form of ERR_PTR(-EINTR).

Use IS_ERR() instead.

Also add a check to uwbd_stop().
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwarc_neep_init() assumes that endpoint 0 is interrupt, but there's no
check for that, which results in a WARNING in USB core code, when a bad
USB descriptor is provided from a device:

usb 1-1: BOGUS urb xfer, pipe 1 != type 3
------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at drivers/usb/core/urb.c:449 usb_submit_urb+0xf8a/0x11d0
Modules linked in:
CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.13.0+ #111
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
task: ffff88006bdc1a00 task.stack: ffff88006bde8000
RIP: 0010:usb_submit_urb+0xf8a/0x11d0 drivers/usb/core/urb.c:448
RSP: 0018:ffff88006bdee3c0 EFLAGS: 00010282
RAX: 0000000000000029 RBX: ffff8800672a7200 RCX: 0000000000000000
RDX: 0000000000000029 RSI: ffff88006c815c78 RDI: ffffed000d7bdc6a
RBP: ffff88006bdee4c0 R08: fffffbfff0fe00ff R09: fffffbfff0fe00ff
R10: 0000000000000018 R11: fffffbfff0fe00fe R12: 1ffff1000d7bdc7f
R13: 0000000000000003 R14: 0000000000000001 R15: ffff88006b02cc90
FS:  0000000000000000(0000) GS:ffff88006c800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe4daddf000 CR3: 000000006add6000 CR4: 00000000000006f0
Call Trace:
 hwarc_neep_init+0x4ce/0x9c0 drivers/uwb/hwa-rc.c:710
 uwb_rc_add+0x2fb/0x730 drivers/uwb/lc-rc.c:361
 hwarc_probe+0x34e/0x9b0 drivers/uwb/hwa-rc.c:858
 usb_probe_interface+0x351/0x8d0 drivers/usb/core/driver.c:361
 really_probe drivers/base/dd.c:385
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:625
 bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
 __device_attach+0x269/0x3c0 drivers/base/dd.c:682
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
 bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
 device_add+0xcf9/0x1640 drivers/base/core.c:1703
 usb_set_configuration+0x1064/0x1890 drivers/usb/core/message.c:1932
 generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
 usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
 really_probe drivers/base/dd.c:385
 driver_probe_device+0x610/0xa00 drivers/base/dd.c:529
 __device_attach_driver+0x230/0x290 drivers/base/dd.c:625
 bus_for_each_drv+0x15e/0x210 drivers/base/bus.c:463
 __device_attach+0x269/0x3c0 drivers/base/dd.c:682
 device_initial_probe+0x1f/0x30 drivers/base/dd.c:729
 bus_probe_device+0x1da/0x280 drivers/base/bus.c:523
 device_add+0xcf9/0x1640 drivers/base/core.c:1703
 usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
 hub_port_connect drivers/usb/core/hub.c:4890
 hub_port_connect_change drivers/usb/core/hub.c:4996
 port_event drivers/usb/core/hub.c:5102
 hub_event+0x23c8/0x37c0 drivers/usb/core/hub.c:5182
 process_one_work+0x9fb/0x1570 kernel/workqueue.c:2097
 worker_thread+0x1e4/0x1350 kernel/workqueue.c:2231
 kthread+0x324/0x3f0 kernel/kthread.c:231
 ret_from_fork+0x25/0x30 arch/x86/entry/entry_64.S:425
Code: 48 8b 85 30 ff ff ff 48 8d b8 98 00 00 00 e8 8e 93 07 ff 45 89
e8 44 89 f1 4c 89 fa 48 89 c6 48 c7 c7 a0 e5 55 86 e8 20 08 8f fd <0f>
ff e9 9b f7 ff ff e8 4a 04 d6 fd e9 80 f7 ff ff e8 60 11 a6
---[ end trace 55d741234124cfc3 ]---

Check that endpoint is interrupt.

Found by syzkaller.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE

Pull networking fixes from David Miller:

 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.

 2) Fix double-free in rmnet driver, from Dan Carpenter.

 3) INET connection socket layer can double put request sockets, fix
    from Eric Dumazet.

 4) Don't match collect metadata-mode tunnels if the device is down,
    from Haishuang Yan.

 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
    be2net driver, from Suresh Reddy.

 6) Fix scaling error in gen_estimator, from Eric Dumazet.

 7) Fix 64-bit statistics deadlock in systemport driver, from Florian
    Fainelli.

 8) Fix use-after-free in sctp_sock_dump, from Xin Long.

 9) Reject invalid BPF_END instructions in verifier, from Edward Cree.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
  Documentation: link in networking docs
  tcp: fix data delivery rate
  bpf/verifier: reject BPF_ALU64|BPF_END
  sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
  sctp: fix an use-after-free issue in sctp_sock_dump
  netvsc: increase default receive buffer size
  tcp: update skb->skb_mstamp more carefully
  net: ipv4: fix l3slave check for index returned in IP_PKTINFO
  net: smsc911x: Quieten netif during suspend
  net: systemport: Fix 64-bit stats deadlock
  net: vrf: avoid gcc-4.6 warning
  qed: remove unnecessary call to memset
  tg3: clean up redundant initialization of tnapi
  tls: make tls_sw_free_resources static
  sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
  MAINTAINERS: review Renesas DT bindings as well
  net_sched: gen_estimator: fix scaling error in bytes/packets samples
  nfp: wait for the NSP resource to appear on boot
  nfp: wait for board state before talking to the NSP
  ...

Pull more input updates from Dmitry Torokhov:
 "A second round of updates for the input subsystem:

   - a new driver for PWM-controlled vibrators

   - ucb1400 touchscreen driver had completely busted suspend/resume
     handling

   - we now handle "home" button found on some devices with Goodix
     touchscreens

   - assorted other fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Gigabyte P57 to the keyboard reset table
  Input: xpad - validate USB endpoint type during probe
  Input: ucb1400_ts - fix suspend and resume handling
  Input: edt-ft5x06 - fix access to non-existing register
  Input: elantech - make arrays debounce_packet static, reduces object code size
  Input: surface3_spi - make const array header static, reduces object code size
  Input: goodix - add support for capacitive home button
  Input: add a driver for PWM controllable vibrators
  Input: adi - make array seq static, reduces object code size

Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the
entire firmware directory.  Unfortunately it thereby also removed the
support for built-in firmware.

This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum.  The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Greg K-H <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix link in filter.txt.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now skb->mstamp_skb is updated later, we also need to call
tcp_rate_skb_sent() after the update is done.

Fixes: 8c72c65b ("tcp: update skb->skb_mstamp more carefully")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for 4.14 for MIPS; below a summary of
  the non-merge commits:

  CM:
   - Rename mips_cm_base to mips_gcr_base
   - Specify register size when generating accessors
   - Use BIT/GENMASK for register fields, order & drop shifts
   - Add cluster & block args to mips_cm_lock_other()

  CPC:
   - Use common CPS accessor generation macros
   - Use BIT/GENMASK for register fields, order & drop shifts
   - Introduce register modify (set/clear/change) accessors
   - Use change_*, set_* & clear_* where appropriate
   - Add CM/CPC 3.5 register definitions
   - Use GlobalNumber macros rather than magic numbers
   - Have asm/mips-cps.h include CM & CPC headers
   - Cluster support for topology functions
   - Detect CPUs in secondary clusters

  CPS:
   - Read GIC_VL_IDENT directly, not via irqchip driver

  DMA:
   - Consolidate coherent and non-coherent dma_alloc code
   - Don't use dma_cache_sync to implement fd_cacheflush

  FPU emulation / FP assist code:
   - Another series of 14 commits fixing corner cases such as NaN
     propgagation and other special input values.
   - Zero bits 32-63 of the result for a CLASS.D instruction.
   - Enhanced statics via debugfs
   - Do not use bools for arithmetic. GCC 7.1 moans about this.
   - Correct user fault_addr type

  Generic MIPS:
   - Enhancement of stack backtraces
   - Cleanup from non-existing options
   - Handle non word sized instructions when examining frame
   - Fix detection and decoding of ADDIUSP instruction
   - Fix decoding of SWSP16 instruction
   - Refactor handling of stack pointer in get_frame_info
   - Remove unreachable code from force_fcr31_sig()
   - Convert to using %pOF instead of full_name
   - Remove the R6000 support.
   - Move FP code from *_switch.S to *_fpu.S
   - Remove unused ST_OFF from r2300_switch.S
   - Allow platform to specify multiple its.S files
   - Add #includes to various files to ensure code builds reliable and
     without warning..
   - Remove __invalidate_kernel_vmap_range
   - Remove plat_timer_setup
   - Declare various variables & functions static
   - Abstract CPU core & VP(E) ID access through accessor functions
   - Store core & VP IDs in GlobalNumber-style variable
   - Unify checks for sibling CPUs
   - Add CPU cluster number accessors
   - Prevent direct use of generic_defconfig
   - Make CONFIG_MIPS_MT_SMP default y
   - Add __ioread64_copy
   - Remove unnecessary inclusions of linux/irqchip/mips-gic.h

  GIC:
   - Introduce asm/mips-gic.h with accessor functions
   - Use new GIC accessor functions in mips-gic-timer
   - Remove counter access functions from irq-mips-gic.c
   - Remove gic_read_local_vp_id() from irq-mips-gic.c
   - Simplify shared interrupt pending/mask reads in irq-mips-gic.c
   - Simplify gic_local_irq_domain_map() in irq-mips-gic.c
   - Drop gic_(re)set_mask() functions in irq-mips-gic.c
   - Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
     gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
   - Convert remaining shared reg access, local int mask access and
     remaining local reg access to new accessors
   - Move GIC_LOCAL_INT_* to asm/mips-gic.h
   - Remove GIC_CPU_INT* macros from irq-mips-gic.c
   - Move various definitions to the driver
   - Remove gic_get_usm_range()
   - Remove __gic_irq_dispatch() forward declaration
   - Remove gic_init()
   - Use mips_gic_present() in place of gic_present and remove
     gic_present
   - Move gic_get_c0_*_int() to asm/mips-gic.h
   - Remove linux/irqchip/mips-gic.h
   - Inline __gic_init()
   - Inline gic_basic_init()
   - Make pcpu_masks a per-cpu variable
   - Use pcpu_masks to avoid reading GIC_SH_MASK*
   - Clean up mti, reserved-cpu-vectors handling
   - Use cpumask_first_and() in gic_set_affinity()
   - Let the core set struct irq_common_data affinity

  microMIPS:
   - Fix microMIPS stack unwinding on big endian systems

  MIPS-GIC:
   - SYNC after enabling GIC region

  NUMA:
   - Remove the unused parent_node() macro

  R6:
   - Constify r2_decoder_tables
   - Add accessor & bit definitions for GlobalNumber

  SMP:
   - Constify smp ops
   - Allow boot_secondary SMP op to return errors

  VDSO:
   - Drop gic_get_usm_range() usage
   - Avoid use of linux/irqchip/mips-gic.h

  Platform changes:

  Alchemy:
   - Add devboard machine type to cpuinfo
   - update cpu feature overrides
   - Threaded carddetect irqs for devboards

  AR7:
   - allow NULL clock for clk_get_rate

  BCM63xx:
   - Fix ENETDMA_6345_MAXBURST_REG offset
   - Allow NULL clock for clk_get_rate

  CI20:
   - Enable GPIO and RTC drivers in defconfig
   - Add ethernet and fixed-regulator nodes to DTS

  Generic platform:
   - Move Boston and NI 169445 FIT image source to their own files
   - Include asm/bootinfo.h for plat_fdt_relocated()
   - Include asm/time.h for get_c0_*_int()
   - Include asm/bootinfo.h for plat_fdt_relocated()
   - Include asm/time.h for get_c0_*_int()
   - Allow filtering enabled boards by requirements
   - Don't explicitly disable CONFIG_USB_SUPPORT
   - Bump default NR_CPUS to 16

  JZ4700:
   - Probe the jz4740-rtc driver from devicetree

  Lantiq:
   - Drop check of boot select from the spi-falcon driver.
   - Drop check of boot select from the lantiq-flash MTD driver.
   - Access boot cause register in the watchdog driver through regmap
   - Add device tree binding documentation for the watchdog driver
   - Add docs for the RCU DT bindings.
   - Convert the fpi bus driver to a platform_driver
   - Remove ltq_reset_cause() and ltq_boot_select(
   - Switch to a proper reset driver
   - Switch to a new drivers/soc GPHY driver
   - Add an USB PHY driver for the Lantiq SoCs using the RCU module
   - Use of_platform_default_populate instead of __dt_register_buses
   - Enable MFD_SYSCON to be able to use it for the RCU MFD
   - Replace ltq_boot_select() with dummy implementation.

  Loongson 2F:
   - Allow NULL clock for clk_get_rate

  Malta:
   - Use new GIC accessor functions

  NI 169445:
   - Add support for NI 169445 board.
   - Only include in 32r2el kernels

  Octeon:
   - Add support for watchdog of 78XX SOCs.
   - Add support for watchdog of CN68XX SOCs.
   - Expose support for mips32r1, mips32r2 and mips64r1
   - Enable more drivers in config file
   - Add support for accessing the boot vector.
   - Remove old boot vector code from watchdog driver
   - Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
   - Make CSR functions node aware.
   - Allow access to CIU3 IRQ domains.
   - Misc cleanups in the watchdog driver

  Omega2+:
   - New board, add support and defconfig

  Pistachio:
   - Enable Root FS on NFS in defconfig

  Ralink:
   - Add Mediatek MT7628A SoC
   - Allow NULL clock for clk_get_rate
   - Explicitly request exclusive reset control in the pci-mt7620 PCI driver.

  SEAD3:
   - Only include in 32 bit kernels by default

  VoCore:
   - Add VoCore as a vendor t0 dt-bindings
   - Add defconfig file"

* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
  MIPS: Refactor handling of stack pointer in get_frame_info
  MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
  MIPS: microMIPS: Fix decoding of swsp16 instruction
  MIPS: microMIPS: Fix decoding of addiusp instruction
  MIPS: microMIPS: Fix detection of addiusp instruction
  MIPS: Handle non word sized instructions when examining frame
  MIPS: ralink: allow NULL clock for clk_get_rate
  MIPS: Loongson 2F: allow NULL clock for clk_get_rate
  MIPS: BCM63XX: allow NULL clock for clk_get_rate
  MIPS: AR7: allow NULL clock for clk_get_rate
  MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
  mips: Save all registers when saving the frame
  MIPS: Add DWARF unwinding to assembly
  MIPS: Make SAVE_SOME more standard
  MIPS: Fix issues in backtraces
  MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
  MIPS: Ci20: Enable RTC driver
  watchdog: octeon-wdt: Add support for 78XX SOCs.
  watchdog: octeon-wdt: Add support for cn68XX SOCs.
  watchdog: octeon-wdt: File cleaning.
  ...

Pull PCI fix from Bjorn Helgaas:
 "Revert an attempt to fix a race while enabling upstream bridges
  because it broke iwlwifi firmware loading"

* tag 'pci-v4.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: Avoid race while enabling upstream bridges"

Pull drm AMD fixes from Dave Airlie:
 "Just had a single AMD fixes pull from Alex for rc1"

* tag 'drm-fixes-for-v4.14-rc1' of git://people.freedesktop.org/~airlied/linux:
  drm/amdgpu: revert "fix deadlock of reservation between cs and gpu reset v2"
  drm/amdgpu: remove duplicate return statement
  drm/amdgpu: check memory allocation failure
  drm/amd/amdgpu: fix BANK_SELECT on Vega10 (v2)
  drm/amdgpu: inline amdgpu_ttm_do_bind again
  drm/amdgpu: fix amdgpu_ttm_bind
  drm/amdgpu: remove the GART copy hack
  drm/ttm:fix wrong decoding of bo_count
  drm/ttm: fix missing inc bo_count
  drm/amdgpu: set sched_hw_submission higher for KIQ (v3)
  drm/amdgpu: move default gart size setting into gmc modules
  drm/amdgpu: refine default gart size
  drm/amd/powerplay: ACG frequency added in PPTable
  drm/amdgpu: discard commands of killed processes
  drm/amdgpu: fix and cleanup shadow handling
  drm/amdgpu: add automatic per asic settings for gart_size
  drm/amdgpu/gfx8: fix spelling typo in mqd allocation
  drm/amd/powerplay: unhalt mec after loading
  drm/amdgpu/virtual_dce: Virtual display doesn't support disable vblank immediately
  drm/amdgpu: Fix huge page updates with CPU

Pull more i2c updates from Wolfram Sang:
 "I2C has two more new drivers: Altera FPGA and STM32F7"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-stm32f7: add driver
  i2c: i2c-stm32f4: use generic definition of speed enum
  dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
  i2c: altera: Add Altera I2C Controller driver
  dt-bindings: i2c: Add Altera I2C Controller

Pull more KVM updates from Paolo Bonzini:
 - PPC bugfixes
 - RCU splat fix
 - swait races fix
 - pointless userspace-triggerable BUG() fix
 - misc fixes for KVM_RUN corner cases
 - nested virt correctness fixes + one host DoS
 - some cleanups
 - clang build fix
 - fix AMD AVIC with default QEMU command line options
 - x86 bugfixes

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  kvm: nVMX: Handle deferred early VMLAUNCH/VMRESUME failure properly
  kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly
  kvm: nVMX: Remove nested_vmx_succeed after successful VM-entry
  kvm,mips: Fix potential swait_active() races
  kvm,powerpc: Serialize wq active checks in ops->vcpu_kick
  kvm: Serialize wq active checks in kvm_vcpu_wake_up()
  kvm,x86: Fix apf_task_wake_one() wq serialization
  kvm,lapic: Justify use of swait_active()
  kvm,async_pf: Use swq_has_sleeper()
  sched/wait: Add swq_has_sleeper()
  KVM: VMX: Do not BUG() on out-of-bounds guest IRQ
  KVM: Don't accept obviously wrong gsi values via KVM_IRQFD
  kvm: nVMX: Don't allow L2 to access the hardware CR8
  KVM: trace events: update list of exit reasons
  KVM: async_pf: Fix #DF due to inject "Page not Present" and "Page Ready" exceptions simultaneously
  KVM: X86: Don't block vCPU if there is pending exception
  KVM: SVM: Add irqchip_split() checks before enabling AVIC
  KVM: Add struct kvm_vcpu pointer parameter to get_enable_apicv()
  KVM: SVM: Refactor AVIC vcpu initialization into avic_init_vcpu()
  KVM: x86: fix clang build
  ...

Neither ___bpf_prog_run nor the JITs accept it.
Also adds a new test case.

Fixes: 17a52670 ("bpf: verifier (add verifier core)")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp_diag would not actually dump out sk/asoc if inet_sctp_diag_fill
returns err, in which case it shouldn't mark sk dumped by setting
cb->args[3] as 1 in sctp_sock_dump().

Otherwise, it could cause some asocs to have no parent's sk dumped
in 'ss --sctp'.

So this patch is to not set cb->args[3] when inet_sctp_diag_fill()
returns err in sctp_sock_dump().

Fixes: 8f840e47 ("sctp: add the sctp_diag.c file")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 86fdb344 ("sctp: ensure ep is not destroyed before doing the
dump") tried to fix an use-after-free issue by checking !sctp_sk(sk)->ep
with holding sock and sock lock.

But Paolo noticed that endpoint could be destroyed in sctp_rcv without
sock lock protection. It means the use-after-free issue still could be
triggered when sctp_rcv put and destroy ep after sctp_sock_dump checks
!ep, although it's pretty hard to reproduce.

I could reproduce it by mdelay in sctp_rcv while msleep in sctp_close
and sctp_sock_dump long time.

This patch is to add another param cb_done to sctp_for_each_transport
and dump ep->assocs with holding tsp after jumping out of transport's
traversal in it to avoid this issue.

It can also improve sctp diag dump to make it run faster, as no need
to save sk into cb->args[5] and keep calling sctp_for_each_transport
any more.

This patch is also to use int * instead of int for the pos argument
in sctp_for_each_transport, which could make postion increment only
in sctp_for_each_transport and no need to keep changing cb->args[2]
in sctp_sock_filter and sctp_sock_dump any more.

Fixes: 86fdb344 ("sctp: ensure ep is not destroyed before doing the dump")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.

Fixes: 8b532797 ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

liujian reported a problem in TCP_USER_TIMEOUT processing with a patch
in tcp_probe_timer() :
      https://www.spinics.net/lists/netdev/msg454496.html

After investigations, the root cause of the problem is that we update
skb->skb_mstamp of skbs in write queue, even if the attempt to send a
clone or copy of it failed. One reason being a routing problem.

This patch prevents this, solving liujian issue.

It also removes a potential RTT miscalculation, since
__tcp_retransmit_skb() is not OR-ing TCP_SKB_CB(skb)->sacked with
TCPCB_EVER_RETRANS if a failure happens, but skb->skb_mstamp has
been changed.

A future ACK would then lead to a very small RTT sample and min_rtt
would then be lowered to this too small value.

Tested:

# cat user_timeout.pkt
--local_ip=192.168.102.64

    0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 `ifconfig tun0 192.168.102.64/16; ip ro add 192.0.2.1 dev tun0`

   +0 < S 0:0(0) win 0 <mss 1460>
   +0 > S. 0:0(0) ack 1 <mss 1460>

  +.1 < . 1:1(0) ack 1 win 65530
   +0 accept(3, ..., ...) = 4

   +0 setsockopt(4, SOL_TCP, TCP_USER_TIMEOUT, [3000], 4) = 0
   +0 write(4, ..., 24) = 24
   +0 > P. 1:25(24) ack 1 win 29200
   +.1 < . 1:1(0) ack 25 win 65530

//change the ipaddress
   +1 `ifconfig tun0 192.168.0.10/16`

   +1 write(4, ..., 24) = 24
   +1 write(4, ..., 24) = 24
   +1 write(4, ..., 24) = 24
   +1 write(4, ..., 24) = 24

   +0 `ifconfig tun0 192.168.102.64/16`
   +0 < . 1:2(1) ack 25 win 65530
   +0 `ifconfig tun0 192.168.0.10/16`

   +3 write(4, ..., 24) = -1

# ./packetdrill user_timeout.pkt
Signed-off-by: Eric Dumazet <edumazet@googl.com>
Reported-by: liujian <liujian56@huawei.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rt_iif is only set to the actual egress device for the output path. The
recent change to consider the l3slave flag when returning IP_PKTINFO
works for local traffic (the correct device index is returned), but it
broke the more typical use case of packets received from a remote host
always returning the VRF index rather than the original ingress device.
Update the fixup to consider l3slave and rt_iif actually getting set.

Fixes: 1dfa7639 ("net: ipv4: add check for l3slave for index returned in IP_PKTINFO")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.

E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock.  If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.

As this is a race condition with a small time window, it is not so easy
to trigger at will.  Using pm_test may increase your chances:

    # echo 0 > /sys/module/printk/parameters/console_suspend
    # echo platform > /sys/power/pm_test
    # echo mem > /sys/power/state

To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.

[    5.780350] ================================
[    5.784679] WARNING: inconsistent lock state
[    5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[    5.794561] --------------------------------
[    5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[    5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[    5.810175]  (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[    5.818327] {SOFTIRQ-ON-W} state was registered at:
[    5.823278]   bcm_sysport_get_stats64+0x17c/0x258
[    5.828053]   dev_get_stats+0x38/0xac
[    5.831776]   rtnl_fill_stats+0x30/0x118
[    5.835761]   rtnl_fill_ifinfo+0x538/0xe24
[    5.839921]   rtmsg_ifinfo_build_skb+0x6c/0xd8
[    5.844430]   rtmsg_ifinfo_event.part.5+0x14/0x44
[    5.849201]   rtmsg_ifinfo+0x20/0x28
[    5.852837]   register_netdevice+0x628/0x6b8
[    5.857171]   register_netdev+0x14/0x24
[    5.861051]   bcm_sysport_probe+0x30c/0x438
[    5.865280]   platform_drv_probe+0x50/0xb0
[    5.869418]   driver_probe_device+0x2e8/0x450
[    5.873817]   __driver_attach+0x104/0x120
[    5.877871]   bus_for_each_dev+0x7c/0xc0
[    5.881834]   bus_add_driver+0x1b0/0x270
[    5.885797]   driver_register+0x78/0xf4
[    5.889675]   do_one_initcall+0x54/0x190
[    5.893646]   kernel_init_freeable+0x144/0x1d0
[    5.898135]   kernel_init+0x8/0x110
[    5.901665]   ret_from_fork+0x14/0x2c
[    5.905363] irq event stamp: 24263
[    5.908804] hardirqs last  enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[    5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[    5.925143] softirqs last  enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[    5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[    5.939985]
[    5.939985] other info that might help us debug this:
[    5.946576]  Possible unsafe locking scenario:
[    5.946576]
[    5.952556]        CPU0
[    5.955031]        ----
[    5.957506]   lock(&syncp->seq#2);
[    5.960955]   <Interrupt>
[    5.963604]     lock(&syncp->seq#2);
[    5.967227]
[    5.967227]  *** DEADLOCK ***
[    5.967227]
[    5.973222] 1 lock held by swapper/0/0:
[    5.977092]  #0:  (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54

So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.

Fixes: 10377ba7 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:

drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]

I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.

Fixes: 9ff74384 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.

Semantic patch used to resolve this issue:

@@
expression e,e2; constant c;
statement S;
@@

  e = kzalloc(e2, c);
  if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'firmware_removal-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull firmware removal from Greg KH:
 "Many many years ago (at the kernel summit in Boston), we all came to
  the agreement that the firmware/ tree should be dropped from the
  kernel, and everyone use the linux-firmware package instead. For some
  minor reason, David Woodhouse didn't send the pull request at that
  point in time, and everyone forgot about this.

  The topic came up in the hallway track at the Plumbers conference this
  week, so here's a single patch that drops the whole firmware tree. The
  last firmware update was back in 2013, and all distros have been using
  linux-firmware instead since at least that year, if not before. The
  only commits to that directory since 2013 was some kbuild fixups for
  various build tool issues.

  So lets finally drop this, we don't need to lug them around in the
  kernel source tree anymore, especially as no one wants or uses them.

  This has passed build testing with 0-day, I don't think it made it
  into linux-next this week, but I figured it was good to get in before
  4.14-rc1 was out"

* tag 'firmware_removal-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  firmware: delete in-kernel firmware

Pull arch/nios2 update from Ley Foon Tan.

* tag 'nios2-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: time: Read timer in get_cycles only if initialized
  nios2: add earlycon support to 3c120 devboard DTS

Pull powerpc fix from Michael Ellerman:
 "Just one fix, for the handling of alignment interrupts on dcbz
  instructions.

  Thanks to Paul Mackerras, Christian Zigotzky, Michal Sojka"

* tag 'powerpc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc: Fix handling of alignment interrupt on dcbz instruction

Pull orangefs updates from Mike Marshall:
 "Some cleanups and a big bug fix for ACLs.

  When I was reviewing Jan Kara's ACL patch, I realized that Orangefs
  ACL code was busted, not just in the kernel module, but in the server
  as well. I've been working on the code in the server mostly, but
  here's one kernel patch, there will be more"

* tag 'for-linus-4.14-ofs2' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
  orangefs: Adjust three checks for null pointers
  orangefs: Use kcalloc() in orangefs_prepare_cdm_array()
  orangefs: Delete error messages for a failed memory allocation in five functions
  orangefs: constify xattr_handler structure
  orangefs: don't call filemap_write_and_wait from fsync
  orangefs: off by ones in xattr size checks
  orangefs: documentation clean up
  orangefs: react properly to posix_acl_update_mode's aftermath.
  orangefs: Don't clear SGID when inheriting ACLs

Prepare second round of input updates for 4.14 merge window.

Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.

BugLink: https://bugs.launchpad.net/bugs/1594214Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>