- 03 Sep, 2022 14 commits
-
-
Johannes Berg authored
Refactor the code to apply QoS settings to the driver so we can call it on link switch. Signed-off-by:Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Catch the bugs fixed in mac80211 by the previous commits and warn if an invalid address is added (or removed). Signed-off-by: -
Johannes Berg authored
When we stop a not-yet-started scan, we erroneously call into the driver, causing a sequence of sw_scan_start() followed by sw_scan_complete() twice. This will cause a warning in hwsim with next in line commit that validates the address passed to wmediumd/virtio. Fix this by doing the calls only if we were actually scanning. Signed-off-by: -
Johannes Berg authored
Right now, we assign the link address only after we add the link to the driver, which is quite obviously wrong. It happens to work in many cases because it gets updated immediately, and then link_conf updates may update it, but it's clearly not really right. Set the link address during ieee80211_mgd_setup_link() so it's set before telling the driver about the link. Fixes: 81151ce4 ("wifi: mac80211: support MLO authentication/association with one link") Signed-off-by:
-
Johannes Berg authored
We probably should've done that originally, we already have about 300 lines of code there, and will add more. Move all the link code we wrote to a new file. Signed-off-by: -
Johannes Berg authored
Refactor some common RX functionality between the netlink and non-netlink paths, adding the special hwsim TLV (if compiled) also in the netlink path. Signed-off-by: -
Johannes Berg authored
Just as an additional check that mac80211 isn't doing anything strange, add a check of the STA magic (which gets assigned when the station is added, and cleared when the station is removed). Signed-off-by: -
Johannes Berg authored
We don't need the sdata argument, and it doesn't make any sense for a direct conversion from one value to another, so just remove the argument Signed-off-by: -
Johannes Berg authored
Now that we have proper multicast TX in mac80211, there's no longer a need to fake something here. Signed-off-by: -
Jinpeng Cui authored
Return value from rdev_set_mcast_rate() directly instead of taking this in another redundant variable. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Jinpeng Cui <cui.jinpeng2@zte.com.cn> Signed-off-by:
-
James Prestwood authored
Adds support in mac80211 for NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE. The motivation behind this functionality is to fix limitations of address randomization on frequencies which are disallowed in world roaming. The way things work now, if a client wants to randomize their address per-connection it must power down the device, change the MAC, and power back up. Here lies a problem since powering down the device may result in frequencies being disabled (until the regdom is set). If the desired BSS is on one such frequency the client is unable to connect once the phy is powered again. For mac80211 based devices changing the MAC while powered is possible but currently disallowed (-EBUSY). This patch adds some logic to allow a MAC change while powered by removing the interface, changing the MAC, and adding it again. mac80211 will advertise support for this feature so userspace can determine the best course of action e.g. disallow address randomization on certain frequencies if not supported. There are certain limitations put on this which simplify the logic: - No active connection - No offchannel work, including scanning. Signed-off-by:
James Prestwood <prestwoj@gmail.com> Signed-off-by:
-
James Prestwood authored
Add a new extended feature bit signifying that the wireless hardware supports changing the MAC address while the underlying net_device is powered. Note that this has a different meaning from IFF_LIVE_ADDR_CHANGE as additional restrictions might be imposed by the hardware, such as: - No connection is active on this interface, carrier is off - No scan is in progress - No offchannel operations are in progress Signed-off-by:
-
Johannes Berg authored
We haven't tried this yet, and it's not very likely to work well right now, so for now disable 4-addr use on interfaces that are MLDs. Signed-off-by:
-
Johannes Berg authored
Do not allow VLANs to be added to AP interfaces that are MLDs, this isn't going to work because the link structs aren't propagated to the VLAN interfaces yet. Signed-off-by:
-
- 02 Sep, 2022 26 commits
-
-
Wolfram Sang authored
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220830201457.7984-2-wsa+renesas@sang-engineering.com
-
Jinpeng Cui authored
Return value from cfg80211_rx_mgmt() directly instead of taking this in another redundant variable. Reported-by:
-
Yang Yingliang authored
Add the missing destroy_workqueue() before return from rtw_core_init() in error path. Fixes: fe101716 ("rtw88: replace tx tasklet with work queue") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Dan Carpenter authored
This does a "chunk_len - 4" subtraction later when it calls: ret = wfx_hif_configuration(wdev, buf + 4, chunk_len - 4); so check for "chunk_len" is less than 4. Fixes: dcbecb49 ("staging: wfx: allow new PDS format") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Jérôme Pouiller <jerome.pouiller@silabs.com> Signed-off-by:
-
Dan Carpenter authored
There some bounds checking to ensure that "map_addr" is not out of bounds before the start of the loop. But the checking needs to be done as we iterate through the loop because "map_addr" gets larger as we iterate. Fixes: 26f1fad2 ("New driver: rtl8xxxu (mac80211)") Signed-off-by:
Jes Sorensen <Jes.Sorensen@gmail.com> Signed-off-by:
-
Ping-Ke Shih authored
Declare this to tell AP we can support beamformee over bandwidth 160M, and then yield better performance in field. Signed-off-by:
-
Ping-Ke Shih authored
Writing address to kick hardware to initialize address CAM, and then poll ready bit to determine completed. Old wrong code poll wrong register address, so it can lead error and fail to bring up interface. Signed-off-by:
-
Ping-Ke Shih authored
Packets containing HTC field with legacy rate could be dropped by AP. If TX rate of report is lower than MCS2, hardware might fall back rate to legacy. Therefore, add a checking rule to avoid HTC field in this situation. Signed-off-by:
-
Ping-Ke Shih authored
Number of TX resource must be minimum of TX_BD and TX_WD. Only considering TX_BD could drop TX packets pulled from mac80211 if TX_WD is unavailable. Fixes: 52edbb9f ("rtw89: ps: access TX/RX rings via another registers in low power mode") Signed-off-by:
-
Ping-Ke Shih authored
We turn off interrupt in ISR, and re-enable interrupt in threadfn or napi_poll according to the mode it stays. If we are turning off interrupt, rtwpci->running flag is unset and interrupt handler stop processing even if it was called, so disallow to re-enable interrupt in this situation. Or, wifi chip doesn't trigger interrupt events anymore because interrupt status (ISR) isn't clear by interrupt handler anymore. Fixes: c83dcd05 ("rtw89: pci: add a separate interrupt handler for low power mode") Signed-off-by:
-
Cheng-Chieh Hsieh authored
The calibration value of XTAL offset may be too large in some wifi modules, that the CFO tracking mechanism under the existing tracking boundary can not adjust the CFO to the tolerable range. So we enlarge it. Signed-off-by:
Cheng-Chieh Hsieh <cj.hsieh@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
We find that suspend/resume tests cause 8852CE lost, because some pci registers are changed for 8852CE. So, correct them accordingly. Signed-off-by:
Chin-Yen Lee <timlee@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
8852CE controls CLKREQ, ASPM L1, L1ss via wifi registers instead, so change them accordingly. Signed-off-by:
-
Chia-Yuan Li authored
There is chance that PCI PHY auto adaption fail. When first time boot up, software restore the right adaption value and close PHY auto adaption mechanism. Signed-off-by:
Chia-Yuan Li <leo.li@realtek.com> Signed-off-by:
-
Chia-Yuan Li authored
It is found that 8852ce loses some beacon after enabling deep ps mode. We set TBTT shift to wake up firmware early to open RF/BB for receiving beacon in time. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
-
Chin-Yen Lee authored
When starting to send heavy traffic in low power mode, driver will call multiple tx wake notify to wake firmware within a short time. In this situation, firmware may miss power mode change request from driver and leads to status error. So we change driver to call power_mode_change at most three times to make sure firmware could get the request. Signed-off-by:
-
Ping-Ke Shih authored
BA CAM entries are global resource of hardware, so move the bitmap and instances to rtw89_cam_info, and then use link list from rtw89_sta to these instances. To check the allocation, add ba_cam to debugfs: map: mac_id: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 addr_cam: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bssid_cam: 01 00 00 00 00 00 00 00 sec_cam: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ba_cam: 03 00 00 00 00 00 00 00 VIF [0] 94:08:53:8e:ef:21 bssid_cam_idx=0 addr_cam_idx=0 -> bssid_cam_idx=0 sec_cam_bitmap=00 00 00 00 00 00 00 00 STA [0] 38:78:62:8b:cb:c6 addr_cam_idx=0 -> bssid_cam_idx=0 sec_cam_bitmap=00 00 00 00 00 00 00 00 ba_cam tid[6]=0, tid[1]=1 Signed-off-by:
-
Ping-Ke Shih authored
The bacam_v1 must do additional initialization, and H2C content of BA CAM is also different. So, correct them accordingly. Signed-off-by:
-
Ping-Ke Shih authored
8852A has 2 BA CAM entries, but 8852C has 8 entries. Add a field to discriminate their differences. Signed-off-by:
-
Zong-Zhe Yang authored
TX power byrate: doesn't change TX power limit: configure values for KCC and UK refine a bit configuration vales TX power limit_ru: configure values for KCC and UK refine a bit configuration values change 6GHz to follow indoor setting configure 6GHz values for ETSI TX power shape: change with TX power limit/limit_ru Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Update 8852c radio A/B parameters from internal HALRF_027_00_071 R49. Signed-off-by:
-
Zong-Zhe Yang authored
Some chips' RF TX power limit/limit_ru tables start to configure some negative values. Fix the setting logic to prevent negative values from polluting fields of others. Signed-off-by:
-
Ching-Te Ku authored
Because RTL8852c firmware handshake use different structure definition with RTL8852a, so it's necessary to update a version for RTL8852c. Signed-off-by:
Ching-Te Ku <ku920601@realtek.com> Signed-off-by:
-
Ching-Te Ku authored
Because the later firmware had patched some new feature, it can control the Wi-Fi/BT slots more efficiently. This patch enhance it for better Wi-Fi SCC mode performance. Signed-off-by:
-
Ching-Te Ku authored
Due to the difference of Wi-Fi firmware supported feature, RTL8852C need to defined more policy to enable the features. (Ex: DBCC, Wi-Fi multi-role, TDMA instant and so on) Signed-off-by:
-
Ching-Te Ku authored
The H2C format and support feature are different. The newer Wi-Fi firmware and driver branch need to handshake more information like DBCC or P2P connection info. Signed-off-by:
-
