- 03 May, 2017 39 commits
-
-
Michal Hocko authored
The current implementation of the reclaim lockup detection can lead to false positives and those even happen and usually lead to tweak the code to silence the lockdep by using GFP_NOFS even though the context can use __GFP_FS just fine. See http://lkml.kernel.org/r/20160512080321.GA18496@dastard as an example. ================================= [ INFO: inconsistent lock state ] 4.5.0-rc2+ #4 Tainted: G O --------------------------------- inconsistent {RECLAIM_FS-ON-R} -> {IN-RECLAIM_FS-W} usage. kswapd0/543 [HC0[0]:SC0[0]:HE1:SE1] takes: (&xfs_nondir_ilock_class){++++-+}, at: xfs_ilock+0x177/0x200 [xfs] {RECLAIM_FS-ON-R} state was registered at: mark_held_locks+0x79/0xa0 lockdep_trace_alloc+0xb3/0x100 kmem_cache_alloc+0x33/0x230 kmem_zone_alloc+0x81/0x120 [xfs] xfs_refcountbt_init_cursor+0x3e/0xa0 [xfs] __xfs_refcount_find_shared+0x75/0x580 [xfs] xfs_refcount_find_shared+0x84/0xb0 [xfs] xfs_getbmap+0x608/0x8c0 [xfs] xfs_vn_fiemap+0xab/0xc0 [xfs] do_vfs_ioctl+0x498/0x670 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x12/0x6f CPU0 ---- lock(&xfs_nondir_ilock_class); <Interrupt> lock(&xfs_nondir_ilock_class); *** DEADLOCK *** 3 locks held by kswapd0/543: stack backtrace: CPU: 0 PID: 543 Comm: kswapd0 Tainted: G O 4.5.0-rc2+ #4 Call Trace: lock_acquire+0xd8/0x1e0 down_write_nested+0x5e/0xc0 xfs_ilock+0x177/0x200 [xfs] xfs_reflink_cancel_cow_range+0x150/0x300 [xfs] xfs_fs_evict_inode+0xdc/0x1e0 [xfs] evict+0xc5/0x190 dispose_list+0x39/0x60 prune_icache_sb+0x4b/0x60 super_cache_scan+0x14f/0x1a0 shrink_slab.part.63.constprop.79+0x1e9/0x4e0 shrink_zone+0x15e/0x170 kswapd+0x4f1/0xa80 kthread+0xf2/0x110 ret_from_fork+0x3f/0x70 To quote Dave: "Ignoring whether reflink should be doing anything or not, that's a "xfs_refcountbt_init_cursor() gets called both outside and inside transactions" lockdep false positive case. The problem here is lockdep has seen this allocation from within a transaction, hence a GFP_NOFS allocation, and now it's seeing it in a GFP_KERNEL context. Also note that we have an active reference to this inode. So, because the reclaim annotations overload the interrupt level detections and it's seen the inode ilock been taken in reclaim ("interrupt") context, this triggers a reclaim context warning where it thinks it is unsafe to do this allocation in GFP_KERNEL context holding the inode ilock..." This sounds like a fundamental problem of the reclaim lock detection. It is really impossible to annotate such a special usecase IMHO unless the reclaim lockup detection is reworked completely. Until then it is much better to provide a way to add "I know what I am doing flag" and mark problematic places. This would prevent from abusing GFP_NOFS flag which has a runtime effect even on configurations which have lockdep disabled. Introduce __GFP_NOLOCKDEP flag which tells the lockdep gfp tracking to skip the current allocation request. While we are at it also make sure that the radix tree doesn't accidentaly override tags stored in the upper part of the gfp_mask. Link: http://lkml.kernel.org/r/20170306131408.9828-3-mhocko@kernel.orgSigned-off-by:
Michal Hocko <mhocko@suse.com> Suggested-by:
Peter Zijlstra <peterz@infradead.org> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Dave Chinner <david@fromorbit.com> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Chris Mason <clm@fb.com> Cc: David Sterba <dsterba@suse.cz> Cc: Jan Kara <jack@suse.cz> Cc: Brian Foster <bfoster@redhat.com> Cc: Darrick J. Wong <darrick.wong@oracle.com> Cc: Nikolay Borisov <nborisov@suse.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Nikolay Borisov authored
Patch series "scope GFP_NOFS api", v5. This patch (of 7): Commit 21caf2fc ("mm: teach mm by current context info to not do I/O during memory allocation") added the memalloc_noio_(save|restore) functions to enable people to modify the MM behavior by disabling I/O during memory allocation. This was further extended in commit 934f3072 ("mm: clear __GFP_FS when PF_MEMALLOC_NOIO is set"). memalloc_noio_* functions prevent allocation paths recursing back into the filesystem without explicitly changing the flags for every allocation site. However, lockdep hasn't been keeping up with the changes and it entirely misses handling the memalloc_noio adjustments. Instead, it is left to the callers of __lockdep_trace_alloc to call the function after they have shaven the respective GFP flags which can lead to false positives: ================================= [ INFO: inconsistent lock state ] 4.10.0-nbor #134 Not tainted --------------------------------- inconsistent {IN-RECLAIM_FS-W} -> {RECLAIM_FS-ON-W} usage. fsstress/3365 [HC0[0]:SC0[0]:HE1:SE1] takes: (&xfs_nondir_ilock_class){++++?.}, at: xfs_ilock+0x141/0x230 {IN-RECLAIM_FS-W} state was registered at: __lock_acquire+0x62a/0x17c0 lock_acquire+0xc5/0x220 down_write_nested+0x4f/0x90 xfs_ilock+0x141/0x230 xfs_reclaim_inode+0x12a/0x320 xfs_reclaim_inodes_ag+0x2c8/0x4e0 xfs_reclaim_inodes_nr+0x33/0x40 xfs_fs_free_cached_objects+0x19/0x20 super_cache_scan+0x191/0x1a0 shrink_slab+0x26f/0x5f0 shrink_node+0xf9/0x2f0 kswapd+0x356/0x920 kthread+0x10c/0x140 ret_from_fork+0x31/0x40 irq event stamp: 173777 hardirqs last enabled at (173777): __local_bh_enable_ip+0x70/0xc0 hardirqs last disabled at (173775): __local_bh_enable_ip+0x37/0xc0 softirqs last enabled at (173776): _xfs_buf_find+0x67a/0xb70 softirqs last disabled at (173774): _xfs_buf_find+0x5db/0xb70 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&xfs_nondir_ilock_class); <Interrupt> lock(&xfs_nondir_ilock_class); *** DEADLOCK *** 4 locks held by fsstress/3365: #0: (sb_writers#10){++++++}, at: mnt_want_write+0x24/0x50 #1: (&sb->s_type->i_mutex_key#12){++++++}, at: vfs_setxattr+0x6f/0xb0 #2: (sb_internal#2){++++++}, at: xfs_trans_alloc+0xfc/0x140 #3: (&xfs_nondir_ilock_class){++++?.}, at: xfs_ilock+0x141/0x230 stack backtrace: CPU: 0 PID: 3365 Comm: fsstress Not tainted 4.10.0-nbor #134 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014 Call Trace: kmem_cache_alloc_node_trace+0x3a/0x2c0 vm_map_ram+0x2a1/0x510 _xfs_buf_map_pages+0x77/0x140 xfs_buf_get_map+0x185/0x2a0 xfs_attr_rmtval_set+0x233/0x430 xfs_attr_leaf_addname+0x2d2/0x500 xfs_attr_set+0x214/0x420 xfs_xattr_set+0x59/0xb0 __vfs_setxattr+0x76/0xa0 __vfs_setxattr_noperm+0x5e/0xf0 vfs_setxattr+0xae/0xb0 setxattr+0x15e/0x1a0 path_setxattr+0x8f/0xc0 SyS_lsetxattr+0x11/0x20 entry_SYSCALL_64_fastpath+0x23/0xc6 Let's fix this by making lockdep explicitly do the shaving of respective GFP flags. Fixes: 934f3072 ("mm: clear __GFP_FS when PF_MEMALLOC_NOIO is set") Link: http://lkml.kernel.org/r/20170306131408.9828-2-mhocko@kernel.orgSigned-off-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
-
David Rientjes authored
After "mm, vmstat: print non-populated zones in zoneinfo", /proc/zoneinfo will show unpopulated zones. The per-cpu pageset statistics are not relevant for unpopulated zones and can be potentially lengthy, so supress them when they are not interesting. Also moves lowmem reserve protection information above pcp stats since it is relevant for all zones per vm.lowmem_reserve_ratio. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1703061400500.46428@chino.kir.corp.google.comSigned-off-by:
David Rientjes <rientjes@google.com> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
David Rientjes authored
Initscripts can use the information (protection levels) from /proc/zoneinfo to configure vm.lowmem_reserve_ratio at boot. vm.lowmem_reserve_ratio is an array of ratios for each configured zone on the system. If a zone is not populated on an arch, /proc/zoneinfo suppresses its output. This results in there not being a 1:1 mapping between the set of zones emitted by /proc/zoneinfo and the zones configured by vm.lowmem_reserve_ratio. This patch shows statistics for non-populated zones in /proc/zoneinfo. The zones exist and hold a spot in the vm.lowmem_reserve_ratio array. Without this patch, it is not possible to determine which index in the array controls which zone if one or more zones on the system are not populated. Remaining users of walk_zones_in_node() are unchanged. Files such as /proc/pagetypeinfo require certain zone data to be initialized properly for display, which is not done for unpopulated zones. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1703031451310.98023@chino.kir.corp.google.comSigned-off-by:
Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by:
-
Xishi Qiu authored
Use is_migrate_isolate_page() to simplify the code, no functional changes. Link: http://lkml.kernel.org/r/58B94FB1.8020802@huawei.comSigned-off-by:
Xishi Qiu <qiuxishi@huawei.com> Acked-by:
-
Xishi Qiu authored
Introduce two helpers, is_migrate_highatomic() and is_migrate_highatomic_page(). Simplify the code, no functional changes. [akpm@linux-foundation.org: use static inlines rather than macros, per mhocko] Link: http://lkml.kernel.org/r/58B94F15.6060606@huawei.comSigned-off-by:
-
Huang Ying authored
Before using cluster lock in free_swap_and_cache(), the swap_info_struct->lock will be held during freeing the swap entry and acquiring page lock, so the page swap count will not change when testing page information later. But after using cluster lock, the cluster lock (or swap_info_struct->lock) will be held only during freeing the swap entry. So before acquiring the page lock, the page swap count may be changed in another thread. If the page swap count is not 0, we should not delete the page from the swap cache. This is fixed via checking page swap count again after acquiring the page lock. I found the race when I review the code, so I didn't trigger the race via a test program. If the race occurs for an anonymous page shared by multiple processes via fork, multiple pages will be allocated and swapped in from the swap device for the previously shared one page. That is, the user-visible runtime effect is more memory will be used and the access latency for the page will be higher, that is, the performance regression. Link: http://lkml.kernel.org/r/20170301143905.12846-1-ying.huang@intel.comSigned-off-by:
"Huang, Ying" <ying.huang@intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: Shaohua Li <shli@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Tim Chen <tim.c.chen@intel.com> Signed-off-by:
-
Johannes Weiner authored
Cgroups currently don't report how much shmem they use, which can be useful data to have, in particular since shmem is included in the cache/file item while being reclaimed like anonymous memory. Add a counter to track shmem pages during charging and uncharging. Link: http://lkml.kernel.org/r/20170221164343.32252-1-hannes@cmpxchg.orgSigned-off-by:
Johannes Weiner <hannes@cmpxchg.org> Reported-by:
Chris Down <cdown@fb.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Signed-off-by:
-
Shaohua Li authored
Show MADV_FREE pages info of each vma in smaps. The interface is for diganose or monitoring purpose, userspace could use it to understand what happens in the application. Since userspace could dirty MADV_FREE pages without notice from kernel, this interface is the only place we can get accurate accounting info about MADV_FREE pages. [mhocko@kernel.org: update Documentation/filesystems/proc.txt] Link: http://lkml.kernel.org/r/89efde633559de1ec07444f2ef0f4963a97a2ce8.1487965799.git.shli@fb.comSigned-off-by:
Shaohua Li <shli@fb.com> Acked-by:
Minchan Kim <minchan@kernel.org> Acked-by:
Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Hugh Dickins <hughd@google.com> Cc: Rik van Riel <riel@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Shaohua Li authored
Now MADV_FREE pages can be easily reclaimed even for swapless system. We can safely enable MADV_FREE for all systems. Link: http://lkml.kernel.org/r/155648585589300bfae1d45078e7aebb3d988b87.1487965799.git.shli@fb.comSigned-off-by:
-
Minchan Kim authored
If a page is swapbacked, it means it should be in swapcache in try_to_unmap_one's path. If a page is !swapbacked, it mean it shouldn't be in swapcache in try_to_unmap_one's path. Check both two cases all at once and if it fails, warn and return SWAP_FAIL. Such bug never mean we should shut down the kernel. [minchan@kernel.org: do not use VM_WARN_ON_ONCE as if condition[ Link: http://lkml.kernel.org/r/20170309060226.GB854@bbox Link: http://lkml.kernel.org/r/20170307055551.GC29458@bboxSigned-off-by:
-
Shaohua Li authored
When memory pressure is high, we free MADV_FREE pages. If the pages are not dirty in pte, the pages could be freed immediately. Otherwise we can't reclaim them. We put the pages back to anonumous LRU list (by setting SwapBacked flag) and the pages will be reclaimed in normal swapout way. We use normal page reclaim policy. Since MADV_FREE pages are put into inactive file list, such pages and inactive file pages are reclaimed according to their age. This is expected, because we don't want to reclaim too many MADV_FREE pages before used once pages. Based on Minchan's original patch [minchan@kernel.org: clean up lazyfree page handling] Link: http://lkml.kernel.org/r/20170303025237.GB3503@bbox Link: http://lkml.kernel.org/r/14b8eb1d3f6bf6cc492833f183ac8c304e560484.1487965799.git.shli@fb.comSigned-off-by:
-
Shaohua Li authored
madv()'s MADV_FREE indicate pages are 'lazyfree'. They are still anonymous pages, but they can be freed without pageout. To distinguish these from normal anonymous pages, we clear their SwapBacked flag. MADV_FREE pages could be freed without pageout, so they pretty much like used once file pages. For such pages, we'd like to reclaim them once there is memory pressure. Also it might be unfair reclaiming MADV_FREE pages always before used once file pages and we definitively want to reclaim the pages before other anonymous and file pages. To speed up MADV_FREE pages reclaim, we put the pages into LRU_INACTIVE_FILE list. The rationale is LRU_INACTIVE_FILE list is tiny nowadays and should be full of used once file pages. Reclaiming MADV_FREE pages will not have much interfere of anonymous and active file pages. And the inactive file pages and MADV_FREE pages will be reclaimed according to their age, so we don't reclaim too many MADV_FREE pages too. Putting the MADV_FREE pages into LRU_INACTIVE_FILE_LIST also means we can reclaim the pages without swap support. This idea is suggested by Johannes. This patch doesn't move MADV_FREE pages to LRU_INACTIVE_FILE list yet to avoid bisect failure, next patch will do it. The patch is based on Minchan's original patch. [akpm@linux-foundation.org: coding-style fixes] Link: http://lkml.kernel.org/r/2f87063c1e9354677b7618c647abde77b07561e5.1487965799.git.shli@fb.comSigned-off-by:
-
Shaohua Li authored
There are a few places the code assumes anonymous pages should have SwapBacked flag set. MADV_FREE pages are anonymous pages but we are going to add them to LRU_INACTIVE_FILE list and clear SwapBacked flag for them. The assumption doesn't hold any more, so fix them. Link: http://lkml.kernel.org/r/3945232c0df3dd6c4ef001976f35a95f18dcb407.1487965799.git.shli@fb.comSigned-off-by:
-
Shaohua Li authored
Patch series "mm: fix some MADV_FREE issues", v5. We are trying to use MADV_FREE in jemalloc. Several issues are found. Without solving the issues, jemalloc can't use the MADV_FREE feature. - Doesn't support system without swap enabled. Because if swap is off, we can't or can't efficiently age anonymous pages. And since MADV_FREE pages are mixed with other anonymous pages, we can't reclaim MADV_FREE pages. In current implementation, MADV_FREE will fallback to MADV_DONTNEED without swap enabled. But in our environment, a lot of machines don't enable swap. This will prevent our setup using MADV_FREE. - Increases memory pressure. page reclaim bias file pages reclaim against anonymous pages. This doesn't make sense for MADV_FREE pages, because those pages could be freed easily and refilled with very slight penality. Even page reclaim doesn't bias file pages, there is still an issue, because MADV_FREE pages and other anonymous pages are mixed together. To reclaim a MADV_FREE page, we probably must scan a lot of other anonymous pages, which is inefficient. In our test, we usually see oom with MADV_FREE enabled and nothing without it. - Accounting. There are two accounting problems. We don't have a global accounting. If the system is abnormal, we don't know if it's a problem from MADV_FREE side. The other problem is RSS accounting. MADV_FREE pages are accounted as normal anon pages and reclaimed lazily, so application's RSS becomes bigger. This confuses our workloads. We have monitoring daemon running and if it finds applications' RSS becomes abnormal, the daemon will kill the applications even kernel can reclaim the memory easily. To address the first the two issues, we can either put MADV_FREE pages into a separate LRU list (Minchan's previous patches and V1 patches), or put them into LRU_INACTIVE_FILE list (suggested by Johannes). The patchset use the second idea. The reason is LRU_INACTIVE_FILE list is tiny nowadays and should be full of used once file pages. So we can still efficiently reclaim MADV_FREE pages there without interference with other anon and active file pages. Putting the pages into inactive file list also has an advantage which allows page reclaim to prioritize MADV_FREE pages and used once file pages. MADV_FREE pages are put into the lru list and clear SwapBacked flag, so PageAnon(page) && !PageSwapBacked(page) will indicate a MADV_FREE pages. These pages will directly freed without pageout if they are clean, otherwise normal swap will reclaim them. For the third issue, the previous post adds global accounting and a separate RSS count for MADV_FREE pages. The problem is we never get accurate accounting for MADV_FREE pages. The pages are mapped to userspace, can be dirtied without notice from kernel side. To get accurate accounting, we could write protect the page, but then there is extra page fault overhead, which people don't want to pay. Jemalloc guys have concerns about the inaccurate accounting, so this post drops the accounting patches temporarily. The info exported to /proc/pid/smaps for MADV_FREE pages are kept, which is the only place we can get accurate accounting right now. This patch (of 6): Johannes pointed out TTU_LZFREE is unnecessary. It's true because we always have the flag set if we want to do an unmap. For cases we don't do an unmap, the TTU_LZFREE part of code should never run. Also the TTU_UNMAP is unnecessary. If no other flags set (for example, TTU_MIGRATION), an unmap is implied. The patch includes Johannes's cleanup and dead TTU_ACTION macro removal code Link: http://lkml.kernel.org/r/4be3ea1bc56b26fd98a54d0a6f70bec63f6d8980.1487965799.git.shli@fb.comSigned-off-by:
-
Geliang Tang authored
Use setup_deferrable_timer() instead of init_timer_deferrable() to simplify the code. Link: http://lkml.kernel.org/r/e8e3d4280a34facbc007346f31df833cec28801e.1488070291.git.geliangtang@gmail.comSigned-off-by:
Geliang Tang <geliangtang@gmail.com> Signed-off-by:
-
Johannes Weiner authored
The backoff mechanism is not needed. If we have MAX_RECLAIM_RETRIES loops without progress, we'll OOM anyway; backing off might cut one or two iterations off that in the rare OOM case. If we have intermittent success reclaiming a few pages, the backoff function gets reset also, and so is of little help in these scenarios. We might want a backoff function for when there IS progress, but not enough to be satisfactory. But this isn't that. Remove it. Link: http://lkml.kernel.org/r/20170228214007.5621-10-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
This reverts commit d7f05528. Now that reclaimability of a node is no longer based on the ratio between pages scanned and theoretically reclaimable pages, we can remove accounting tricks for pages skipped due to zone constraints. Link: http://lkml.kernel.org/r/20170228214007.5621-9-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
NR_PAGES_SCANNED counts number of pages scanned since the last page free event in the allocator. This was used primarily to measure the reclaimability of zones and nodes, and determine when reclaim should give up on them. In that role, it has been replaced in the preceding patches by a different mechanism. Being implemented as an efficient vmstat counter, it was automatically exported to userspace as well. It's however unlikely that anyone outside the kernel is using this counter in any meaningful way. Remove the counter and the unused pgdat_reclaimable(). Link: http://lkml.kernel.org/r/20170228214007.5621-8-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
Commit 246e87a9 ("memcg: fix get_scan_count() for small targets") sought to avoid high reclaim priorities for memcg by forcing it to scan a minimum amount of pages when lru_pages >> priority yielded nothing. This was done at a time when reclaim decisions like dirty throttling were tied to the priority level. Nowadays, the only meaningful thing still tied to priority dropping below DEF_PRIORITY - 2 is gating whether laptop_mode=1 is generally allowed to write. But that is from an era where direct reclaim was still allowed to call ->writepage, and kswapd nowadays avoids writes until it's scanned every clean page in the system. Potential changes to how quick sc->may_writepage could trigger are of little concern. Remove the force_scan stuff, as well as the ugly multi-pass target calculation that it necessitated. Link: http://lkml.kernel.org/r/20170228214007.5621-7-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
Commit 246e87a9 ("memcg: fix get_scan_count() for small targets") sought to avoid high reclaim priorities for kswapd by forcing it to scan a minimum amount of pages when lru_pages >> priority yielded nothing. Commit b95a2f2d ("mm: vmscan: convert global reclaim to per-memcg LRU lists"), due to switching global reclaim to a round-robin scheme over all cgroups, had to restrict this forceful behavior to unreclaimable zones in order to prevent massive overreclaim with many cgroups. The latter patch effectively neutered the behavior completely for all but extreme memory pressure. But in those situations we might as well drop the reclaimers to lower priority levels. Remove the check. Link: http://lkml.kernel.org/r/20170228214007.5621-6-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
NUMA balancing already checks the watermarks of the target node to decide whether it's a suitable balancing target. Whether the node is reclaimable or not is irrelevant when we don't intend to reclaim. Link: http://lkml.kernel.org/r/20170228214007.5621-5-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
Commit 1d82de61 ("mm, vmscan: make kswapd reclaim in terms of nodes") allowed laptop_mode=1 to start writing not just when the priority drops to DEF_PRIORITY - 2 but also when the node is unreclaimable. That appears to be a spurious change in this patch as I doubt the series was tested with laptop_mode, and neither is that particular change mentioned in the changelog. Remove it, it's still recent. Link: http://lkml.kernel.org/r/20170228214007.5621-4-hannes@cmpxchg.orgSigned-off-by:
Mel Gorman <mgorman@techsingularity.net> Acked-by:
-
Johannes Weiner authored
PF_MEMALLOC direct reclaimers get throttled on a node when the sum of all free pages in each zone fall below half the min watermark. During the summation, we want to exclude zones that don't have reclaimables. Checking the same pgdat over and over again doesn't make sense. Fixes: 599d0c95 ("mm, vmscan: move LRU lists to node") Link: http://lkml.kernel.org/r/20170228214007.5621-3-hannes@cmpxchg.orgSigned-off-by:
-
Johannes Weiner authored
Patch series "mm: kswapd spinning on unreclaimable nodes - fixes and cleanups". Jia reported a scenario in which the kswapd of a node indefinitely spins at 100% CPU usage. We have seen similar cases at Facebook. The kernel's current method of judging its ability to reclaim a node (or whether to back off and sleep) is based on the amount of scanned pages in proportion to the amount of reclaimable pages. In Jia's and our scenarios, there are no reclaimable pages in the node, however, and the condition for backing off is never met. Kswapd busyloops in an attempt to restore the watermarks while having nothing to work with. This series reworks the definition of an unreclaimable node based not on scanning but on whether kswapd is able to actually reclaim pages in MAX_RECLAIM_RETRIES (16) consecutive runs. This is the same criteria the page allocator uses for giving up on direct reclaim and invoking the OOM killer. If it cannot free any pages, kswapd will go to sleep and leave further attempts to direct reclaim invocations, which will either make progress and re-enable kswapd, or invoke the OOM killer. Patch #1 fixes the immediate problem Jia reported, the remainder are smaller fixlets, cleanups, and overall phasing out of the old method. Patch #6 is the odd one out. It's a nice cleanup to get_scan_count(), and directly related to #5, but in itself not relevant to the series. If the whole series is too ambitious for 4.11, I would consider the first three patches fixes, the rest cleanups. This patch (of 9): Jia He reports a problem with kswapd spinning at 100% CPU when requesting more hugepages than memory available in the system: $ echo 4000 >/proc/sys/vm/nr_hugepages top - 13:42:59 up 3:37, 1 user, load average: 1.09, 1.03, 1.01 Tasks: 1 total, 1 running, 0 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.0 us, 12.5 sy, 0.0 ni, 85.5 id, 2.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 31371520 total, 30915136 used, 456384 free, 320 buffers KiB Swap: 6284224 total, 115712 used, 6168512 free. 48192 cached Mem PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 76 root 20 0 0 0 0 R 100.0 0.000 217:17.29 kswapd3 At that time, there are no reclaimable pages left in the node, but as kswapd fails to restore the high watermarks it refuses to go to sleep. Kswapd needs to back away from nodes that fail to balance. Up until commit 1d82de61 ("mm, vmscan: make kswapd reclaim in terms of nodes") kswapd had such a mechanism. It considered zones whose theoretically reclaimable pages it had reclaimed six times over as unreclaimable and backed away from them. This guard was erroneously removed as the patch changed the definition of a balanced node. However, simply restoring this code wouldn't help in the case reported here: there *are* no reclaimable pages that could be scanned until the threshold is met. Kswapd would stay awake anyway. Introduce a new and much simpler way of backing off. If kswapd runs through MAX_RECLAIM_RETRIES (16) cycles without reclaiming a single page, make it back off from the node. This is the same number of shots direct reclaim takes before declaring OOM. Kswapd will go to sleep on that node until a direct reclaimer manages to reclaim some pages, thus proving the node reclaimable again. [hannes@cmpxchg.org: check kswapd failure against the cumulative nr_reclaimed count] Link: http://lkml.kernel.org/r/20170306162410.GB2090@cmpxchg.org [shakeelb@google.com: fix condition for throttle_direct_reclaim] Link: http://lkml.kernel.org/r/20170314183228.20152-1-shakeelb@google.com Link: http://lkml.kernel.org/r/20170228214007.5621-2-hannes@cmpxchg.orgSigned-off-by:
Shakeel Butt <shakeelb@google.com> Reported-by:
Jia He <hejianet@gmail.com> Tested-by:
-
Greg Thelen authored
Each slab kmem cache has per cpu array caches. The array caches are created when the kmem_cache is created, either via kmem_cache_create() or lazily when the first object is allocated in context of a kmem enabled memcg. Array caches are replaced by writing to /proc/slabinfo. Array caches are protected by holding slab_mutex or disabling interrupts. Array cache allocation and replacement is done by __do_tune_cpucache() which holds slab_mutex and calls kick_all_cpus_sync() to interrupt all remote processors which confirms there are no references to the old array caches. IPIs are needed when replacing array caches. But when creating a new array cache, there's no need to send IPIs because there cannot be any references to the new cache. Outside of memcg kmem accounting these IPIs occur at boot time, so they're not a problem. But with memcg kmem accounting each container can create kmem caches, so the IPIs are wasteful. Avoid unnecessary IPIs when creating array caches. Test which reports the IPI count of allocating slab in 10000 memcg: import os def ipi_count(): with open("/proc/interrupts") as f: for l in f: if 'Function call interrupts' in l: return int(l.split()[1]) def echo(val, path): with open(path, "w") as f: f.write(val) n = 10000 os.chdir("/mnt/cgroup/memory") pid = str(os.getpid()) a = ipi_count() for i in range(n): os.mkdir(str(i)) echo("1G\n", "%d/memory.limit_in_bytes" % i) echo("1G\n", "%d/memory.kmem.limit_in_bytes" % i) echo(pid, "%d/cgroup.procs" % i) open("/tmp/x", "w").close() os.unlink("/tmp/x") b = ipi_count() print "%d loops: %d => %d (+%d ipis)" % (n, a, b, b-a) echo(pid, "cgroup.procs") for i in range(n): os.rmdir(str(i)) patched: 10000 loops: 1069 => 1170 (+101 ipis) unpatched: 10000 loops: 1192 => 48933 (+47741 ipis) Link: http://lkml.kernel.org/r/20170416214544.109476-1-gthelen@google.comSigned-off-by:Greg Thelen <gthelen@google.com> Acked-by:
Joonsoo Kim <iamjoonsoo.kim@lge.com> Acked-by:
-
Geliang Tang authored
Use offset_in_page() macro instead of open-coding. Link: http://lkml.kernel.org/r/4dbc77ccaaed98b183cf4dba58a4fa325fd65048.1492758503.git.geliangtang@gmail.comSigned-off-by:
-
Junxiao Bi authored
Configfs is the interface for ocfs2-tools to set configure to kernel and $configfs_dir/cluster/$clustername/heartbeat/dead_threshold is the one used to configure heartbeat dead threshold. Kernel has a default value of it but user can set O2CB_HEARTBEAT_THRESHOLD in /etc/sysconfig/o2cb to override it. Commit 45b99773 ("ocfs2/cluster: use per-attribute show and store methods") changed heartbeat dead threshold name while ocfs2-tools did not, so ocfs2-tools won't set this configurable and the default value is always used. So revert it. Fixes: 45b99773 ("ocfs2/cluster: use per-attribute show and store methods") Link: http://lkml.kernel.org/r/1490665245-15374-1-git-send-email-junxiao.bi@oracle.comSigned-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Acked-by:
Joseph Qi <jiangqi903@gmail.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by:
-
Geliang Tang authored
Use setup_timer() instead of init_timer() to simplify the code. Link: http://lkml.kernel.org/r/5e75bf07beb91e092d5aa36c36769949a480456a.1489060564.git.geliangtang@gmail.comSigned-off-by:
-
Masahiro Yamada authored
In many of clk_disable() implementations, it is a no-op for a NULL pointer input, but this is one of the exceptions. Making it treewide consistent will allow clock consumers to call clk_disable() without NULL pointer check. Link: http://lkml.kernel.org/r/1490692624-11931-4-git-send-email-yamada.masahiro@socionext.comSigned-off-by:
Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Steven Miao <realmz6@gmail.com> Signed-off-by:
-
Colin Ian King authored
Here are some of the more common spelling mistakes that I've found while fixing up spelling mistakes in kernel error message text. They probably should be added to this list so we don't keep on seeing them appearing again. Link: http://lkml.kernel.org/r/20170421122534.5378-1-colin.king@canonical.comSigned-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Kees Cook <keescook@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Joe Perches <joe@perches.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Pankaj Gupta authored
Interrupt enable/disabled with spinlock is not a valid operation for RT as it can make executing tasks sleep from a non-sleepable context. So convert it to spin_lock_irq[save, restore]. Link: http://lkml.kernel.org/r/1492065666-3816-1-git-send-email-pagupta@redhat.comSigned-off-by:
Pankaj Gupta <pagupta@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: Vinod Koul <vinod.koul@intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Ville Syrjl <ville.syrjala@linux.intel.com> Cc: Miles Chen <miles.chen@mediatek.com> Cc: Marcelo Tosatti <mtosatti@redhat.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
git://git.infradead.org/users/pcmoore/auditLinus Torvalds authored
Pull audit updates from Paul Moore: "Fourteen audit patches for v4.12 that span the full range of fixes, new features, and internal cleanups. We have a patches to move to 64-bit timestamps, convert refcounts from atomic_t to refcount_t, track PIDs using the pid struct instead of pid_t, convert our own private audit buffer cache to a standard kmem_cache, log kernel module names when they are unloaded, and normalize the NETFILTER_PKT to make the userspace folks happier. From a fixes perspective, the most important is likely the auditd connection tracking RCU fix; it was a rather brain dead bug that I'll take the blame for, but thankfully it didn't seem to affect many people (only one report). I think the patch subject lines and commit descriptions do a pretty good job of explaining the details and why the changes are important so I'll point you there instead of duplicating it here; as usual, if you have any questions you know where to find us. We also manage to take out more code than we put in this time, that always makes me happy :)" * 'stable-4.12' of git://git.infradead.org/users/pcmoore/audit: audit: fix the RCU locking for the auditd_connection structure audit: use kmem_cache to manage the audit_buffer cache audit: Use timespec64 to represent audit timestamps audit: store the auditd PID as a pid struct instead of pid_t audit: kernel generated netlink traffic should have a portid of 0 audit: combine audit_receive() and audit_receive_skb() audit: convert audit_watch.count from atomic_t to refcount_t audit: convert audit_tree.count from atomic_t to refcount_t audit: normalize NETFILTER_PKT netfilter: use consistent ipv4 network offset in xt_AUDIT audit: log module name on delete_module audit: remove unnecessary semicolon in audit_watch_handle_event() audit: remove unnecessary semicolon in audit_mark_handle_event() audit: remove unnecessary semicolon in audit_field_valid()
-
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-securityLinus Torvalds authored
Pull security subsystem updates from James Morris: "Highlights: IMA: - provide ">" and "<" operators for fowner/uid/euid rules KEYS: - add a system blacklist keyring - add KEYCTL_RESTRICT_KEYRING, exposes keyring link restriction functionality to userland via keyctl() LSM: - harden LSM API with __ro_after_init - add prlmit security hook, implement for SELinux - revive security_task_alloc hook TPM: - implement contextual TPM command 'spaces'" * 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (98 commits) tpm: Fix reference count to main device tpm_tis: convert to using locality callbacks tpm: fix handling of the TPM 2.0 event logs tpm_crb: remove a cruft constant keys: select CONFIG_CRYPTO when selecting DH / KDF apparmor: Make path_max parameter readonly apparmor: fix parameters so that the permission test is bypassed at boot apparmor: fix invalid reference to index variable of iterator line 836 apparmor: use SHASH_DESC_ON_STACK security/apparmor/lsm.c: set debug messages apparmor: fix boolreturn.cocci warnings Smack: Use GFP_KERNEL for smk_netlbl_mls(). smack: fix double free in smack_parse_opts_str() KEYS: add SP800-56A KDF support for DH KEYS: Keyring asymmetric key restrict method with chaining KEYS: Restrict asymmetric key linkage using a specific keychain KEYS: Add a lookup_restriction function for the asymmetric key type KEYS: Add KEYCTL_RESTRICT_KEYRING KEYS: Consistent ordering for __key_link_begin and restrict check KEYS: Add an optional lookup_restriction hook to key_type ... -
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivialLinus Torvalds authored
Pull trivial tree updates from Jiri Kosina. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: tty: fix comment for __tty_alloc_driver() init/main: properly align the multi-line comment init/main: Fix double "the" in comment Fix dead URLs to ftp.kernel.org drivers: Clean up duplicated email address treewide: Fix typo in xml/driver-api/basics.xml tools/testing/selftests/powerpc: remove redundant CFLAGS in Makefile: "-Wall -O2 -Wall" -> "-O2 -Wall" selftests/timers: Spelling s/privledges/privileges/ HID: picoLCD: Spelling s/REPORT_WRTIE_MEMORY/REPORT_WRITE_MEMORY/ net: phy: dp83848: Fix Typo UBI: Fix typos Documentation: ftrace.txt: Correct nice value of 120 priority net: fec: Fix typo in error msg and comment treewide: Fix typos in printk
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatchingLinus Torvalds authored
Pull livepatch updates from Jiri Kosina: - a per-task consistency model is being added for architectures that support reliable stack dumping (extending this, currently rather trivial set, is currently in the works). This extends the nature of the types of patches that can be applied by live patching infrastructure. The code stems from the design proposal made [1] back in November 2014. It's a hybrid of SUSE's kGraft and RH's kpatch, combining advantages of both: it uses kGraft's per-task consistency and syscall barrier switching combined with kpatch's stack trace switching. There are also a number of fallback options which make it quite flexible. Most of the heavy lifting done by Josh Poimboeuf with help from Miroslav Benes and Petr Mladek [1] https://lkml.kernel.org/r/20141107140458.GA21774@suse.cz - module load time patch optimization from Zhou Chengming - a few assorted small fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching: livepatch: add missing printk newlines livepatch: Cancel transition a safe way for immediate patches livepatch: Reduce the time of finding module symbols livepatch: make klp_mutex proper part of API livepatch: allow removal of a disabled patch livepatch: add /proc/<pid>/patch_state livepatch: change to a per-task consistency model livepatch: store function sizes livepatch: use kstrtobool() in enabled_store() livepatch: move patching functions into patch.c livepatch: remove unnecessary object loaded check livepatch: separate enabled and patched states livepatch/s390: add TIF_PATCH_PENDING thread flag livepatch/s390: reorganize TIF thread flag bits livepatch/powerpc: add TIF_PATCH_PENDING thread flag livepatch/x86: add TIF_PATCH_PENDING thread flag livepatch: create temporary klp_update_patch_state() stub x86/entry: define _TIF_ALLWORK_MASK flags explicitly stacktrace/x86: add function for detecting reliable stack traces
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hidLinus Torvalds authored
Pull HID subsystem updates from Jiri Kosina: - The need for HID_QUIRK_NO_INIT_REPORTS per-device quirk has been growing dramatically during past years, so the time has come to switch over the default, and perform the pro-active reading only in cases where it's really needed (multitouch, wacom). The only place where this behavior is (in some form) preserved is hiddev so that we don't introduce userspace-visible change of behavior. From Benjamin Tissoires - HID++ support for power_supply / baterry reporting. From Benjamin Tissoires and Bastien Nocera - Vast improvements / rework of DS3 and DS4 in Sony driver. From Roderick Colenbrander - Improvment (in terms of getting closer to the Microsoft's interpretation of slightly ambiguous specification) of logical range interpretation in case null-state is set in the rdesc. From Valtteri Heikkilä and Tomasz Kramkowski - A lot of newly supported device IDs and small assorted fixes * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (71 commits) HID: usbhid: Add HID_QUIRK_NOGET for Aten CS-1758 KVM switch HID: asus: support backlight on USB keyboards HID: wacom: Move wacom_remote_irq and wacom_remote_status_irq HID: wacom: generic: sync pad events only for actual packets HID: sony: remove redundant check for -ve err HID: sony: Make sure to unregister sensors on failure HID: sony: Make DS4 bt poll interval adjustable HID: sony: Set proper bit flags on DS4 output report HID: sony: DS4 use brighter LED colors HID: sony: Improve navigation controller axis/button mapping HID: sony: Use DS3 MAC address as unique identifier on USB HID: logitech-hidpp: add a sysfs file to tell we support power_supply HID: logitech-hidpp: enable HID++ 1.0 battery reporting HID: logitech-hidpp: add support for battery status for the K750 HID: logitech-hidpp: battery: provide CAPACITY_LEVEL HID: logitech-hidpp: rename battery level into capacity HID: logitech-hidpp: battery: provide ONLINE property HID: logitech-hidpp: notify battery on connect HID: logitech-hidpp: return an error if the queried feature is not present HID: logitech-hidpp: create the battery for all types of HID++ devices ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrlLinus Torvalds authored
Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.12 cycle. The extra week before the merge window actually resulted in some of the type of fixes that usually arrive after the merge window already starting to trickle in from eager developers using -next, I'm impressed. I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal with the onset of Samsung patches. It works great. Apart from that it is a boring round, just incremental updates and fixes all over the place, no serious core changes or anything exciting like that. The most pleasing to see is Julia Cartwrights work to audit the irqchip-providing drivers for realtime locking compliance. It's one of those "I should really get around to looking into that" things that have been on my TODO list since forever. Summary: Core changes: - add bi-directional and output-enable pin configurations to the generic bindings and generic pin controlling core. New drivers or subdrivers: - Armada 37xx SoC pin controller and GPIO support. - Axis ARTPEC-6 SoC pin controller support. - AllWinner A64 R_PIO controller support, and opening up the AllWinner sunxi driver for ARM64 use. - Rockchip RK3328 support. - Renesas R-Car H3 ES2.0 support. - STM32F469 support in the STM32 driver. - Aspeed G4 and G5 pin controller support. Improvements: - a whole slew of realtime improvements to drivers implementing irqchips: BCM, AMD, SiRF, sunxi, rockchip. - switch meson driver to get the GPIO ranges from the device tree. - input schmitt trigger support on the Rockchip driver. - enable the sunxi (AllWinner) driver to also be used on ARM64 silicon. - name the Qualcomm QDF2xxx GPIO lines. - support GMMR GPIO regions on the Intel Cherryview. This fixes a serialization problem on these platforms. - pad retention support for the Samsung Exynos 5433. - handle suspend-to-ram in the AT91-pio4 driver. - pin configuration support in the Aspeed driver. Cleanups: - the final name of Rockchip RK1108 was RV1108 so rename the driver and variables to stay consistent" * tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits) pinctrl: mediatek: Add missing pinctrl bindings for mt7623 pinctrl: artpec6: Fix return value check in artpec6_pmx_probe() pinctrl: artpec6: Remove .owner field for driver pinctrl: tegra: xusb: Silence sparse warnings ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller" pinctrl: make artpec6 explicitly non-modular pinctrl: aspeed: g5: Add pinconf support pinctrl: aspeed: g4: Add pinconf support pinctrl: aspeed: Add core pinconf support pinctrl: aspeed: Document pinconf in devicetree bindings pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl pinctrl: stm32: Add STM32F469 MCU support Documentation: dt: Remove ngpios from stm32-pinctrl binding pinctrl: stm32: replace device_initcall() with arch_initcall() pinctrl: stm32: add possibility to use gpio-ranges to declare bank range pinctrl: armada-37xx: Add gpio support pinctrl: armada-37xx: Add pin controller support for Armada 37xx pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers pinctrl: core: Make pinctrl_init_controller() static pinctrl: generic: Add bi-directional and output-enable ... -
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds authored
Pull MMC updates from Ulf Hansson: "MMC core: - Continue to re-factor code to prepare for eMMC CMDQ and blkmq support - Introduce queue semantics to prepare for eMMC CMDQ and blkmq support - Add helper functions to manage temporary enable/disable of eMMC CMDQ - Improve wait-busy detection for SDIO MMC host: - cavium: Add driver to support Cavium controllers - cavium: Extend Cavium driver to support Octeon and ThunderX SOCs - bcm2835: Add new driver for Broadcom BCM2835 controller - sdhci-xenon: Add driver to support Marvell Xenon SDHCI controller - sdhci-tegra: Add support for the Tegra186 variant - sdhci-of-esdhc: Support for UHS-I SD cards - sdhci-of-esdhc: Support for eMMC HS200 cards - sdhci-cadence: Add eMMC HS400 enhanced strobe support - sdhci-esdhc-imx: Reset tuning circuit when needed - sdhci-pci: Modernize and clean-up some PM related code - sdhci-pci: Avoid re-tuning at runtime PM for some Intel devices - sdhci-pci|acpi: Use aggressive PM for some Intel BYT controllers - sdhci: Re-factoring and modernizations - sdhci: Optimize delay loops - sdhci: Improve register dump print format - sdhci: Add support for the Command Queue Engine - meson-gx: Various improvements and clean-ups - meson-gx: Add support for CMD23 - meson-gx: Basic tuning support to avoid CRC errors - s3cmci: Enable probing via DT - mediatek: Improve tuning support for eMMC HS200 and HS400 mode - tmio: Improve DMA support - tmio: Use correct response for CMD12 - dw_mmc: Minor improvements and clean-ups" * tag 'mmc-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (148 commits) mmc: sdhci-of-esdhc: limit SD clock for ls1012a/ls1046a mmc: sdhci-of-esdhc: poll ESDHC_CLOCK_STABLE bit with udelay mmc: sdhci-xenon: Fix default value of LOGIC_TIMING_ADJUST for eMMC5.0 PHY mmc: sdhci-xenon: Fix the work flow in xenon_remove(). MIPS: Octeon: cavium_octeon_defconfig: Enable Octeon MMC mmc: sdhci-xenon: Remove redundant dev_err call in get_dt_pad_ctrl_data() mmc: cavium: Use module_pci_driver to simplify the code mmc: cavium: Add MMC support for Octeon SOCs. mmc: cavium: Fix detection of block or byte addressing. mmc: core: Export API to allow hosts to get the card address mmc: sdio: Fix sdio wait busy implement limitation mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card clk: apn806: fix spelling mistake: "mising" -> "missing" mmc: sdhci-of-esdhc: add delay between tuning cycles mmc: sdhci: Control the delay between tuning commands mmc: sdhci-of-esdhc: add tuning support mmc: sdhci-of-esdhc: add support for signal voltage switch mmc: sdhci-of-esdhc: add peripheral clock support mmc: sdhci-pci: Allow for 3 bytes from Intel DSM mmc: cavium: Fix a shift wrapping bug ...
-
- 02 May, 2017 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds authored
Pull networking updates from David Millar: "Here are some highlights from the 2065 networking commits that happened this development cycle: 1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri) 2) Add a generic XDP driver, so that anyone can test XDP even if they lack a networking device whose driver has explicit XDP support (me). 3) Sparc64 now has an eBPF JIT too (me) 4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei Starovoitov) 5) Make netfitler network namespace teardown less expensive (Florian Westphal) 6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana) 7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger) 8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky) 9) Multiqueue support in stmmac driver (Joao Pinto) 10) Remove TCP timewait recycling, it never really could possibly work well in the real world and timestamp randomization really zaps any hint of usability this feature had (Soheil Hassas Yeganeh) 11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay Aleksandrov) 12) Add socket busy poll support to epoll (Sridhar Samudrala) 13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso, and several others) 14) IPSEC hw offload infrastructure (Steffen Klassert)" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits) tipc: refactor function tipc_sk_recv_stream() tipc: refactor function tipc_sk_recvmsg() net: thunderx: Optimize page recycling for XDP net: thunderx: Support for XDP header adjustment net: thunderx: Add support for XDP_TX net: thunderx: Add support for XDP_DROP net: thunderx: Add basic XDP support net: thunderx: Cleanup receive buffer allocation net: thunderx: Optimize CQE_TX handling net: thunderx: Optimize RBDR descriptor handling net: thunderx: Support for page recycling ipx: call ipxitf_put() in ioctl error path net: sched: add helpers to handle extended actions qed*: Fix issues in the ptp filter config implementation. qede: Fix concurrency issue in PTP Tx path processing. stmmac: Add support for SIMATIC IOT2000 platform net: hns: fix ethtool_get_strings overflow in hns driver tcp: fix wraparound issue in tcp_lp bpf, arm64: fix jit branch offset related to ldimm64 bpf, arm64: implement jiting of BPF_XADD ...
-
